Tektronix CSA7000 User manual

020-2423-xx
CSA7000 Series
Adapter Instructions

071-1014-00

CAUTION

RefertoHost

Instrument Manual

O/E Electrical Out-to-CH1 Input Adapter
Product Description

The O/E Electrical Out-to-CH1 Input adapter
allows you to connect the output of the
optical-to-electrical converter to the CH1 input on
Tektronix CSA7000 Series instruments. The
adapter preserves maximum signal integrity and
eliminates the need for additional external adapters
and cables, which can degrade the voltage
standing wave ratio (VSWR).

Installing the Adapter

1. Insert the O/E-to-SMA adapter onto the BMA
connector on the instrument.

2. Screw the adapter onto the BMA connector
finger tight.

3. Connect an SMA-type device to the adapter.

4. Connect the SMA-type device to the
circuit-under-test.

Removing the Adapter

1. Disconnect the device input and ground from
the circuit-under-test.

2. Disconnect the SMA-type device from the
adapter (if necessary, use a wrench).

3. Unscrew the adapter from the BMA connector
(if necessary, use a 7/16-inch wrench).

Storing the Adapter

Y ou may store the adapter in the cover of the
O/E-to-TekConnect adapter (see Figure 3).

www.tektronix.com

*P071101400*

071101400

Safety Summary

To avoid potential hazards, use these products
only as specified.

To avoid fire or personal injury

Connect and disconnect properly. Connect the

adapter to the host instrument before connecting
the device or cable to the circuit-under-test. Dis­connect the device input and ground from the
circuit-under-test before disconnecting the device
from the adapter and host instrument.

Ground the product. This product is indirectly

grounded through the grounding conductor of the
host instrument power cord. To avoid electric
shock, the grounding conductor must be con­nected to earth ground. Before making connec­tions to the input or output terminals of the prod­uct, ensure that the product is properly grounded.

Observe all terminal ratings. To avoid fire or shock

hazard, observe all ratings and markings on the
host instrument. Consult the host instrument
documentation for further ratings information
before making connections to the host instrument.

Do not apply a potential to any terminal, including
the common terminal, that exceeds the maximum
rating of that terminal.

Do not operate without covers. Do not operate this

product with covers or panels removed.

Do not operate with suspected failures. If you

suspect there is damage to this product, have it
inspected by qualified service personnel.

Do not operate in wet/damp conditions.

Do not operate in an explosive atmosphere.

Keep product surfaces clean and dry.

Figure 1: O/E Electrical Out-to-CH1 input adapter
(013-0327-xx)

Using the Adapter

The adapter connects directly to the TekConnect
interface on the host instrument.

Installing the Adapter

1. Insert the adapter into the TekConnect
interface for CH 1 on the instrument until the
adapter locks in place.

2. Finger tighten the two screws to provide
additional strength to hold the adapter in
place.

Removing the Adapter

1. Unscrew the two screws holding the adapter
in place (use a screw driver if necessary).

2. Remove the adapter from the instrument.

O/E-to-SMA Adapter
Product Description

The O/E-to-SMA adapter allows you to connect
cables with SMA connectors to the output of the
optical-to-electrical converter on CSA7000 Series
instruments. The adapter preserves maximum
signal integrity and eliminates the need for
additional external adapters, which can degrade
the voltage standing wave ratio (VSWR).

Figure 2: O/E-to-SMA Adapter (013-0326-xx)

Using the Adapter

The adapter connects directly to the BMA output
connector of the O/E converter on the instrument.

Figure 3: Storing the adapter

Additional Information

For additional information on using the adapters,
refer to the documentation for the host instrument.

WARRANTY SUMMARY

Tektronix warrants that the products that it
manufactures and sells will be free from defects in
materials and workmanship for a period of one (1)
year from the date of shipment. If a product
proves defective within the respective period,
Tektronix will provide repair or replacement as
described in the complete warranty statement.

To arrange for service or obtain a copy of the
complete warranty statement, please contact your
nearest Tektronix sales and service office.

EXCEPT AS PROVIDED IN THIS SUMMARY
OR THE APPLICABLE WARRANTY
STATEMENT, TEKTRONIX MAKES NO
WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED, INCLUDING WITHOUT
LIMITATION THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. IN NO EVENT
SHALL TEKTRONIX BE LIABLE FOR
INDIRECT, SPECIAL OR CONSEQUENTIAL
DAMAGES.

Copyright  Tektronix, Inc.

Beaverton, OR 97077