Tektronix CG5011 Specifications Sheet

The CG 5011 is the premier choice to fill all your scope calibration requirements, manual and automated. The CG 5011, with time markers from 5 seconds down to 0.5 ns, is designed to cover both analog and digital oscilloscope verification and calibration.
The CG 5011 includes a Remote Pulse head as a standard accessory. It provides very fast risetime pulses of less than 160 ps, useful for bandwidth testing on vertical amplifiers as an alternative to a leveled sine wave generator.
The CG 5011 offers a wide range of functions, all programmable either by controller via the GPIB or from the front panel. ALearn mode allows any manually set function or range to be acquired by a controller.
The CG 5011 is even able to keep track of its next due date for calibration, using the Next-Cal-Date tracking feature. Built-in self-test routines and hardware check the operation of all major circuits each time power is turned on.
Options add even more capability. The CG 5011 can be used with the optional Comparator Head to calibrate built-in oscilloscope calibrators. The oscilloscope calibrator and CG 5011 signals are applied to the Comparator Head and displayed simultaneously on the scope’s CRT. Errors are then automatically displayed on the CG 5011 readout.
The Remote Variable option permits operation of the following front-panel
controls: Units/Div, Variable-Fixed button, Continue button and the VAR.
Configure the CG 5011 for your own calibration station requirements. As three­wide TM 5000 Series modules, each one can stand alone in a TM 5003 mainframe or be used with a companion SG 5030 Programmable Leveled Sine Wave Generator in a six-slot TM 5006Amainframe. Both are ideally suited for environments where multiple scopes are maintained.
Finally, whether it’s a single instrument or a complete calibration package, you can count on TEGAM to offer more support of your purchase, including comprehensive manuals, applications assistance, updates and a worldwide service network.
CG 5011 Fully Pr o grammab le Calibration Generator for Analog and Digital Oscilloscopes
• Extended time markers to 0.5 ns
• Next-Cal-Date tracking
• Pulse rise times to 160 picoseconds
• Positive & negative DC capability
• Learn mode
• Flexible configuration
• Easy integration in GPIB (IEEE-488) systems
MODULAR TEST INSTRUMENTS
TM 500 / 5000
CG 5011 Analog and Digital Scope Calibration Range
(time markers)
5 sec/div 10 ns/div .5 ns/div
THE GLOBAL SOURCE FOR PROVEN TEST
AND MEASUREMENT TECHNOLOGY.
Prices and specifications subject to change without notice.
Current (Amplitude Mode)
(Used to calibrate current probes.) Range — 1 mA to 100 mA(1-2-5
sequence).
Multipliers — 1, 2, 3, 4, 5, 6, 8 or 10. Aberrations — Less than 5% of period
and less than ±15% of amplitude (±100 µA).
Accuracy — ±(0.25% +2 µA). Frequency — DC or 10 Hz to 1 MHz
(decade steps).
Droop — 1% p-p amplitude. Variable Range — ±9.9%.
Low Edge (Amplitude Mode)
(Used to test input amplifier and attenuator compensation.)
Range — 20 mV to 1 V p-p, 50 Ω load only (1-2-5 steps with multipliers).
Multipliers — 1, 2, 3, 4, 5, 6, 8 or 10. Aberrations — ±2% of square wave
amplitude.
Accuracy — ±3%. Polarity — Positive or negative transi-
tions to ground.
Risetime/Fall time — <1.3 ns. Long T erm Flatness —±0.5% after first 10 ns. Frequency —10 Hz to 1 MHz (decade steps). Variable Amplitude Range — ±9.9%
from nominal.
High Edge (Amplitude Mode)
(Used to test input amplifier and attenuator compensation.)
Range — 1.2 V to 100 V p-p, 1 M Ω load (1-2-5 steps with multipliers).
Multipliers — 1, 2, 3, 4, 5, 6, 8 or 10. Aberrations — ±2% of square wave
amplitude.
Accuracy — ±3%. Polarity — Positive transition only
(negative voltage rising to ground).
Risetime — <100 ns. Long Term Flatness — ±0.5% after first
500 ns. Frequency — 10 Hz to 100 kHz (decade
steps). Variable Amplitude Range — ≥±9.9%
from nominal.
MODULAR TEST INSTRUMENTS
CG 5011 Specifications Voltage (Amplitude Mode)
(Used to calibrate vertical display accuracy .) Range — 40 µ V to 200 V, 1 M Ωload;
40 µ V to 5 V , 50 load (1-2-5 steps with multiplier).
Multipliers — 1,2,3,4, 5, 6, 8 or 10. Polarity — Positive from ground. Aberrations — Less than ± 15% of
amplitude (± 10 mV).
Accuracy — ±(0.25% +1 µ V). Frequency —
40 µ V to 80 mV 10 Hz to 10 kHz 100 mV to 10 V 10 Hz to 100 kHz
+dc or -dc
12 V to 200 V 10 Hz to 10 kHz
+dc or -dc
Variable Range — ±9.9%.
TM 500 / 5000
Markers (Timing Mode)
(Used to calibrate oscilloscope time bases.)
Range — 5 s to 0.5 ns (1-2-5 steps). X10 Magnifier — Increases marker rate
by a factor of 10 (5 s to 0.1 µs range only). Accuracy — ±0.0003%
(+15°C to +50°C). Amplitude — 1 V minimum 5 s to 2 ns,
350 mV minimum: 1 ns, 100 mVminimum:
0.5 ns into 5 Ω. Variable Range — ±9.9%.
T rigger Output
Output Amplitude — 1 V minimum into 50 Ω. TriggerRate (Marker Mode) — Normal:
slaved to marker rate from 5 s to 100 ns; remains at 100 ns for faster markers.
Divided by 10: reduces normal trigger rate by a factor of ten.
Divided by 100: reduces normal trigger rate by a factor of one hundred.
All Other Modes — Normal: slaved to output frequency. Divided by 10: one-tenth output frequency. Divided by 100: one­hundredth output frequency.
Reference Frequency
Output Frequency — 1 MHz with internal time base accuracy.
Output Amplitude — TTL compatible. Input Frequency — 1, 2, 3, 4 or 5 MHz.
Input Amplitude — 1 V to 10 VRMS
displayed via EXT REF indicator on front panel.
Required Accuracy — ±0.001%. Input Resistance — 10 k(nominal).
Fast Edge (Amplitude Mode)
(Used to generate fast rise, low distortion pulses for testing higher bandwidth vertical amplifiers.)
Polarity — Positive or negative transitions from ground.
Risetime — 160 ps. Aberrations — ±3% of pulse amplitude;
not to exceed 4% p-p for adjacent peaks. Frequency — 100 Hz to 100 kHz
(decade steps).
Amplitude — 1.1 V peak ±5% into 50 Ω. Variable Range — ±10%.
Environmental
(Meets or exceeds MIL-T-28800C, Class 5 requirements with the exception of non­operating temperature.)
Ambient T emperatur e — Operating: 0°C to +50°C. Non-operating: -20°C to + 65°C.
Altitude — Operating: 4500 m (15,000 ft.). Non-operating: 15,000 m (50,000 ft.).
Vibration — Operating: displacement (p-p) 0.38 mm (0.015 inch). V ibration frequency: 10 Hz - 55 Hz. Total time: 75 minutes.
Relative Humidity — 90% - 95% at +50°C for 5 days.
Shock — Non-operating: 30 g’s, 1/2 sine, 11 ms duration, three shocks in each direction along three major axes; total shocks, 18.
Bench Handling — Operating: 45˚ or 4 inches or point of balance, whichever occurs first.
Physical Characteristics
Dimensions mm in
Width 203 8.0 Height 126 5.0 Depth 305 12.0
Weights kg lb
Standard 4.3 9.5 Option 01 4.4 9.6 Option 02 4.0 8.7
A TM 5003 or TM 5006A Mainframe is required to operate the CG 5011.
Optional Accessories
Comparator Head — Used to calibrate built-in oscilloscope calibrators against the signals available from the CG 5011. Both the oscilloscope calibrator and CG 5011 signals are then varied to obtain congruent displays. Errors are then displayed on the CG 5011 readout. (015-0310-01)
Remote V ariable — Permits remote operation of the following front panel controls: Units/Div, Variable-Fixed Button, Continue Push button and the VAR. (015-0309-01)
Ordering Information
CG 5011 Programmable Calibration Generator
Includes: Output Cable Assembly (012-0884-01), Pulse Head (015-0611-01), Instruction Manual (070-7745-02), Service Manual (070-7746-00), Instrument Interface Guide (070-7747-00), Programmer’s Reference Manual (070-7748-00).
CG 5011/DP CG 5011 w/Delete
Pulse Head
015-0265-00 Precision Voltage
Divider 015-0309-01 Remote V ariable 015-0310-01 Comparator Head 015-0611-01 Pulse Head 067-0681-01 Tunnel Diode Pulser 067-0974-00 Troubleshooting Aid
TM 5003 3 Wide Power Module
Mainframe, GPIB TM 5003/RI TM 5003 w/Rear
Interface TM 5006A 6 Wide Power Module
Mainframe, GPIB TM 5006A/R TM 5006Aw/Rack
Mount TM 5006A/RI TM 5006Aw/Rear
Interface TM 5006A/R/RI TM 5006Aw/Rack Mt
& Rear Interface TM 5006A/EMC TM 5006Aw/EMC
Shielding
Mainframe Power Plug Options
Standard 120V North American UE220 220V Universal Euro
& Switzerland UK240 240V United Kingdom A240 240VAustralian NA240 240V North American S220 220V Switzerland
Warranty
One year on materials and workmanship.
Calibration Documentation
Contact TEGAM for OPTION Z540 NIST Traceable Compliance Certificate and Test Data.
Calibration & T echnical Services
For warranty and remedial repair, calibration services and spare parts, or for additional information on TEGAM sales and service offices around the world, contact us at 440-466-6100 (ph) or 440-466-6110 (fx).
MODULAR TEST INSTRUMENTS
TM 500 / 5000
CG5011.991PG
THE GLOBAL SOURCE FOR PROVEN TEST
AND MEASUREMENT TECHNOLOGY.
TEN TEGAM WAY • GENEVA,OHIO 44041
440-466-6100 • FAX 440-466-6110
www.tegam.com • e-mail:sales@tegam.com
Loading...