BSARack
xx
ZZZ
Rackmount kit
Instructions
*P071349900*
071-3499-00
xx
BSARack
ZZZ
Rackmount kit
Instructions
Register now!
Click the following link to protect your product.
► www.tek.com/register
www.tek.com
071-3499-00
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14150 SW Karl Braun Drive
P.O. Box 50 0
Beaverto
USA
For product information, sales, service, and technical support:
n, OR 97077
In North America, call 1-800-833-9200.
Worldwide, visit www.tek.com to find contacts in your area.
Warranty
Tektronix warrants that this p roduct will be free from defects in materials and workmanship for a period of one (1)
year from the date of shipment. If any such product proves defective during this warranty period, Tektronix, at its
option, either will repair the defective product without charge for parts and labor, or will provide a replacement
in exchange for the defective product. Parts, modules and replacement products used by Tektronix for warranty
work may be n
the property of Tektronix.
ew or reconditioned to like new performance. All replaced parts, modules and products become
In order to o
the warranty period and make suitable arrangements for the performance of service. Customer shall be responsible
for packaging and shipping the defective product to the service center designated by Tektronix, with shipping
charges prepaid. Tektronix shall pay for the return of the product to Customer if the shipment is to a location within
the country in which the Tektronix service center is located. Customer shall be responsible for paying all shipping
charges, duties, taxes, and any other charges for products returned to any other locations.
This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate
maintenance and care. Tektronix shall not be obligated to furnish service under this warranty a) to repair damage
result
b) to repair damage resulting from improper use or connection to incompatible equipment; c) to repair any damage
or malfunction caused by the use of non-Tektronix supplies; or d) to service a product that has b een modified or
integrated with other products when the effect of such modification or integration increases the time or difficulty
of servicing the product.
THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THE PRODUCT IN LIEU OF ANY
OTHER WARRANTIES, EXPRESS OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
TRONIX' RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE
TEK
AND EXCLUSIVE REMEDY PR OVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY.
TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS
ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.
[W2 – 15AUG04]
btain service under this warranty, Customer must notify Tektronix of the defect before the expiration of
ing from attempts by personnel other than Tektronix representatives to install, repair or service the product;
Table of Contents
Service safety summary............................................................................................ ii
Introduction ......................................................................................................... 1
Warranted characteristics ..................................................................................... 2
Clearance r
Installation instructions ............................................................................................ 5
Minimum tool and equipment list................................. ................................ ........... 5
Assemble the rack slides and brackets and install them in the rack cabinet............................. 5
Install the rack tray assembly into the rack cabinet ... ................................ ..................... 8
Install the instrument onto the rack tray ................................ .................................. ... 9
equirements ....................................................................................... 3
BSA Rackmount kit instructions i
Service safety summary
Service safet
ysummary
The Service s
safely perform service on the product. Only qualified personnel should perform
service procedures. Read this Service safety summary and the General safety
summary before performing any service procedures.
To avoid electric shock. Do not touch exposed connections.
Do not service alone. Do not perform internal service or adjustments of this
product unless another person capable of rendering first aid and resuscitation is
present.
Disconnect power. To avoid electric shock, switch off the product power and
disconn
panels, or opening the case for servicing.
Use care when servicing with power on. Dangerous voltages or currents may exist
in this product. Disconnect power, remove battery (if applicable), and disconnect
test leads before removing protective panels, soldering, or replacing components.
Verify safety after repair. Always recheck ground continuity and mains dielectric
strength after performing a repair.
afety summary section contains additional information required to
ect the power cord from the mains power before removing any covers or
ii BSA Rackmount kit instructions
Introduction
This document describes the installation of the BSARACK rackmount kit
for BERTScope products. The kit instructions are a collection of parts that,
once installed, configure the instrument for mounting into a standard 19-inch
instrument rack.
The following table and figure show the parts list for the rackmount kit.
Table 1: Parts list
Item
number Quantity Part number Description
-
-
1 1 650-5549-00
2 4 212-0001-00
3 1 386-7984-00
4 1 351-1140-00
5
6 16 212-0260-00
7
8 8 212-0577-00
1
1 071-3499-xx Technical manual: Instructions, this document
4 220-0285-00
8 210-1596–00
BSARACK Rackmount kit: BERTScope Series, consisting of the following items:
Rackmount kit; BERTScope series, preassembled
Screw, mach; 8-32 x 0.25, PNH, Steel, zinc plated, T20 TORX
Plate, filler, rackmount
Bracket kit, two (2) front and two (2) rear brackets, with hardware
Nut bar strip, 10-32 (x4) 2.63 long, 0.12 thick
Screw, mach; 10-32 x 0.375, PNH, Steel, zinc plated, T25 TORX
Flat washer, #12 x 0.5 outer diameter X 0.12 thick
Screw, mach; 10-32 x 0.625, TRH, Steel, zinc plated head, Phillips
BSA Rackmount kit instructions 1
Introduction
Figure 1: Rackmount kit parts
Warranted characteristics
When the instrument is installed according to the instructions in this document,
ack-mounted instrument meets all warranted requirements listed in the
the r
instrument specification except for those listed in Environmental Requirements.
truments mounted using methods other than those described in these
Ins
instructions may not meet their warranted requirements.
e Specifications in the user manual that apply to your instrument.
Se
Cooling air enters from the bottom-front and both sides. You must provide
dequate cool air to meet the ambient temperature requirements.
a
2 BSA Rackmount kit instructions
Introduction
Cleara
nce requirements
Figure 2: Instrument cooling
The rack in which the rack-adapted instrument is mounted must provide the
following clearance requirements:
A minimum of 10.5 inches (266.7 mm) of vertical space
A minimum of 19 inches (482.6 mm) between the left and right front rails of
the rack
A minimum depth of 25 inches (635 mm)
CAUTION. Failure to adhere to the clearance requirements can result in
overheating and cause instrument faults or failure. Air temperature at the
strument’s intake air vents must be maintained within the specified ambient
in
temperature range (+10 °C to +35 °C) during instrument operation. Always
adhere to the clearance requirements to provide the rack-mounted instrument with
enough clearance for air circulation and accommodation of the power cord,
cables, and mounting hardware.
BSA Rackmount kit instructions 3
Introduction
Figure 3: Instrument dimensions with clearance requirements in the rack
4 BSA Rackmount kit instructions
Installation instructions
This section c ontains the procedures needed to rack mount a BERTScope
instrument. The following steps are involved in the installation process:
Install the slide bracket kit and hardware to the rack.
Install the rack tray into the rack cabinet.
Install the instrument onto the rack tray.
Attach remaining hardware to t he instrument and rack assembly and then
secure the instrument in place.
Minimum tool and equipment list
The following table lists the readily-available tools for the installation process.
Table 2: Tools required for rackmount installation
Installation instructions
Name Description
No. 2 Phillips or Pozidriv tip
T-15 Torx tip
T-20 Torx tip
These instructions are for personnel who are familiar with servicing the product.
Contact your local Tektronix Service Center or Tektronix Factory Service for
allation information.
inst
Phillips or Pozidriv-driver tip for number 2 screw heads
Torx®-driver tip for T-15 size screw heads
Torx®-driver tip for T-20 size screw heads
Assemble the rack slides and brackets and install them in the rack cabinet
mplete the following steps to remove the outer member of the rack slides
Co
from the pre-assembled rack tray and install the rack slides with the brackets in
the rack cabinet.
1. Locate the pre-assembled rack tray from the kit contents (Item 1) and place it
on an open and clean working surface.
BSA Rackmount kit instructions 5
Installation instructions
2. Refer to the fol
assemblies from both sides of the pre-assembled rack tray. (First push the
button latch near the bottom rear edge of each rack slide assembly to disengage
the rack slide from the rack tray. Then remove the rack slide assembly.)
lowing figure and remove the outer members of the rack slide
Figure 4: Removing the rack slides from the rack tray
6 BSA Rackmount kit instructions
Installation instructions
3. Complete the fo
the rack slides and then install the rack slides in the rack cabinet. Refer to the
following figure as needed.
llowing steps to install the brackets to the outer members of
Figure 5: Installing the rack slides and brackets to the rack cabinet
a. Use four screws with flat washers, lock washers, and nuts from the bracket
kit (Item 4) to secure the front and rear brackets to one of the rack slide
emblies. Repeat for this step for the other rack slide assembly.
ass
b. Use four machine screws (Item 6) to secure one of the rack slides with
rear bracket to the rack cabinet.
the
c. Use four machine screws (Item 6) and the nut bar (Item 5) to secure rack
ide to the front of the rack cabinet.
sl
d. Repeat the steps b and c to install the other rack slide assembly in the
ack cabinet.
r
BSA Rackmount kit instructions 7
Installation instructions
Install the rack tray assembly into the rack cabinet
Complete the following steps to install the rack tray assembly into the rack cabinet:
1. Grab the rack tray assembly and slide it into rack slides in the cabinet as
shown in the following figure.
Figure 6: Slide the rack tray assembly into the rack slides in the rack cabinet
2. Push the rack tray into the cabinet until it locks in place.
8 BSA Rackmount kit instructions
Install the instrument onto the rack tray
Complete the following procedures to install the instrument onto the rack tray.
Refer to the figure for an overview of the final installation process. (See Figure 7.)
Installation instructions
re 7: Final installation steps
Figu
WAR NI NG . To prevent the instrument from tipping or dropping onto the installers,
two or more people should install the instrument into the rack cabinet.
After completing the installation procedure, the installers should verify that the
instrument and the rack cabinet will not tip forward while the instrument is in
e extended position.
th
Do not leave the instrument extended in the rack when finished accessing the
ear panel.
r
BSA Rackmount kit instructions 9
Installation instructions
1. Pull the rack tr
2. Remove the handles from both sides of the instrument and secure them to the
optional stor
just removed.
3. With the hel
extended rack tray, making sure that the feet of the instrument fit into the
holes on the bottom of the rack tray and the brackets on the sides of the rack
tray line up with screw holes of the handles that you just removed.
4. Locate the four T-20 Torx screws from the parts lists (Item 2) and install two
of the screws on each side of the instrument into holes where the handles
used to be.
NOTE. The remaining steps in this document secure the rack tray to the rack
cabinet
instrument.
5. Connect the instrument power cord to the rear of the instrument and any
6. Push the rack tray all of the way into the rack cabinet.
s. Be sure to connect the power cord and any cables to the rear of the
cables that may be required for certain instrument configurations.
ay out of the rack cabinet until it locks in place.
age location on rear of the rack tray using the screws that you
p of another individual, carefully place the instrument on the
7. Locate three p airs of 10-32 Phillips screws (Item 8) and three washers (Item 7)
from the kit and install them through the rack kit side plates and into the rack;
repeat for both sides of the instrument.
8. Locate the filler plate (Item 3) and use the two remaining 10-32 screws and
washers to secure the filler plate to the rack cabinet below the rack tray.
End of Document
10 BSA Rackmount kit instructions
Loading...