xx
AWG-HDMI
ZZZ
Declassification and Security
Instructions
www.tek.com
P077156200*
*
077-1562-00
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14150 SW Karl Braun Drive
P.O . Bo x 50 0
Beaverto
USA
For product information, sales, service, and technical support:
n, OR 97077
In North America, call 1-800-833-9200.
Worldwide, visit www.tek.com to find contacts in your area.
Table of Contents
Preface .............................................................................................................. iii
Memory devices ............... ................................ ................................ ..................... 1
Clear or sanitize a non-functional instrument .. ... . .. . ... . ... .... ... . ... . .. . ... . ... . ... ... . ... . .. . ... . ... . ... ... 2
AWG-HDMI Declassification and Security Instructions i
Table of Contents
ii AWG-HDMI Declassification and Security Instructions
Preface
This document helps customers with data security concerns to sanitize or remove
memory devices from the Tektronix AWG-HDMI
There is no declassification specified for this product. The only information this
device holds is factory calibration information for the delay times. There is no
customer in
formation stored on the device and nothing can be accessed externally.
Reference
Required documents
Terms that may be used in
this document
The procedures in this document are written to meet the requirements specified in:
NISPOM, DoD 5220.22–M, Chapter 8
ISFO Process Manual for Certification & Accreditation of Classified Systems
under NISPOM
No external documents are required to perform the procedures in this document.
The following terms may be used in this document:
Clear. This removes data on memory before reusing it in a secured area. All
reusable memory is cleared to deny ac ces s to previously stored information
by standard means of access.
Instrument Declassification. A term that refers to procedures that must be
undertaken before an instrument can be removed from a secure environment.
Declassification procedures include memory sanitization and memory
removal, and sometimes both.
Nonvolatile memory. Data is retained when the instrument is powered off.
Remove. This is a physical means to clear the data by removing the memory
device from the instrument. Instructions are available in the product Service
Manual.
Sanitize. This eradicates the data from media/memory so that the data cannot
be recovered by other means or technology. This is typically used when the
device will be moved (temporarily or permanently) from a secured area to a
non-secured area.
User Accessible. User is able to directly retrieve the memory device contents.
Volatile memory. Data is lost when the instrument is powered off.
AWG-HDMI Declassification and Security Instructions iii
Preface
Device terms
User data. Desc
waveforms or other measurement data representing signals connected to the
instrument by users.
User settings. Describes the type of information stored in the device. Refers
to instrument settings that can be changed by the user.
Both. Describes the type of information stored in the device. It means that
both user data and user settings are stored in the device.
None. Describes the type of information stored in the device. It means that
neither user data nor user settings are stored in the device.
Directly. Describes how data is modified. It means that the user can modify
the data.
Indirectly. Describes how data is modified. It means that the instrument
system resources modify the data and that the user cannot modify the data.
ribes the type of information stored in the device. Refers to
iv AWG-HDMI Declassification and Security Instructions
Memory devices
Volatile memory devices
Type
of user
Type and
min. size Function
1GB SDRAM
Holds
current
delay and
voltage
values
System
memory
Non-volatile memory
info
stored
Delay
value
and
voltage
offset
value
devices
There is no declassification specified for this product. The only information this
device holds is factory calibration information for the delay times. There is no
customer information stored on the device and nothing can be accessed externally.
Backed
up by
battery
No Directly
Method
of
modification
and
indirectly
Data
Input
method Location
Visa
commands
(Direct)
System
memory
written by
processor
system
(Indirect)
SBC
(Single
Board
Computer)
User
accessible To clear To sanitize
User can
access
delay and
voltage
values via
Visa, but
nothing
else
Remove
power from
the instrument
foratleast20
seconds.
Remove
power
from the
instrument
for at least 20
seconds.
Type and
min. size Function
SanDisk
Industrial
Micro SD
Card
8GB
Holds
AWG-HD
control
software and
ration
calib
values
Typ e
of user
info
stored
None Indirectly Factory
MI
Method of
modification
Data
Input
method Location
configu
ration
Micro SD
slot on
internal
SBC
(Single
Board
Compu
ter)
User
accessible To clear To sanitize
No Not applicable.
t contain
Does no
user data
or settings.
ing
Clear
would disable
instrument
ionality.
funct
Not applicable.
t
Does no
contain user
data or settings.
ing
Clear
would disable
instrument
ionality.
funct
AWG-HDMI Declassification and Security Instructions 1
Clear or sanitize a non-functional instrument
Clearorsanit
Charges
ize a non-functional instrument
If your instr
No user data is stored on the instrument when the power is removed. Clearing or
sanitizing the instrument is not applicable.
Replacemen
the time of replacement.
ument is not functioning, return the instrument to Tektronix for repair.
t of any missing hardware will be charged according to the rate at
2AWG-HDMIDeclassification and Security Instructions
Loading...