xx
AWG50CUP and AWG70CUP
Upgrades for AWG5000C and AWG7000C
ZZZ
Series Instruments
Instructions
www.tektronix.com
P075100900*
*
075-1009-00
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14200 SW Karl Braun Drive
P.O . Bo x 5 0 0
Beaverto
USA
For product information, sales, service, and technical support:
n, OR 97077
In North America, call 1-800-833-9200.
Worl d wide , visi t www.tektronix.com to find contacts in your area.
Kit Description
Products
This kit provides instructions to install an o ption on an AWG5000C or
AWG7000C series instrument. Once installed, the upgrade is equivalent to a
factory-installed option.
For a list of available options, see the Tektronix Web site (www.tektronix.com), or
contact your Tektronix representative.
AWG5000C and AWG7000C series B010100 and above
Kit Parts
Insta
llation Instructions
List
Option Quantity Part number Description
All 1 each
All 1 each 075-0xxx-00
1
NS – Not Salable
tall your new option(s), you need the key number that is provided with this
To ins
kit. This unique key number is valid only for the specific model number and serial
number of your instrument; it will not work on any other instrument. This single
key number enables all valid options for your instrument, those that were factory
installed and any others that you may have already purchased. In other words, this
new key number supersedes any previous key numbers that you may already have.
TION. To avoid losing your options, do not misplace the paper label included
CAU
with this kit. This label contains the option installation key number and should be
installed on the rear panel of the instrument for future reference.
As a backup, copy the key number and save it with the other important papers
for your instrument. If you ever need to re-enable the option, you must reenter
this key number.
NS
1
LABEL, OPTION INFORMATION
MANUAL, KIT INSTRUCTIONS
AWG50CUP & AWG70CUP Upgrades for AWG5000C & AWG7000C Series Instruments 1
Installation Instructions
Install the Op
tion
Perform the following steps to enable your new option:
1. Power on the instrument.
2. From the menu bar, select the System menu, and then select Option
Installation.
3. The Option Installation dialog box is displayed.
Figure 1: Option Installation dialog box (1)
4. Click Continue to display a second dialog box.
2 AWG50CUP & AWG70CUP Upgrades for AWG5000C & AWG7000C Series Instruments
Installation Instructions
Figure 2: Option Installation dialog box (2)
5. To enable the new options, enter the alphanumeric key number exactly as it is
printed on the label in the area located at the bottom of the dialog box.
6. Attach the label to the rear panel over the existing label.
AWG50CUP & AWG70CUP Upgrades for AWG5000C & AWG7000C Series Instruments 3
Installation Instructions
Verify the Opt
ion Upgrade
Complete the following steps to verify that the option upgrade was successful:
1. Restart the instrument.
2. Select the Help menu, and then select About Tektronix AWG.
3. Verify that the option that you installed is listed in the Options box. (See
Figure3onpage4.)
The following example shows that Option01isinstalledontheinstrument.
ure 3: About Tektronix AWG
Fig
of Document
End
4 AWG50CUP & AWG70CUP Upgrades for AWG5000C & AWG7000C Series Instruments
Loading...