Tektronix AWG701AUP, AWG702AUP Field Install Instructions

xx
AWG701AUP AWG702AUP Options 01, 03, and SSD-0x
ZZZ
AWG70000A Series Upgrades
Instructions
www.tek.com
*
075-1049-03
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material. Specications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc. 14150 SW Karl Braun Drive P.O . Bo x 5 0 0 Beaverto USA
For product information, sales, service, and technical support:
n, OR 97077
In North America, call 1-800-833-9200. Worldwide, visit www.tek.com to nd contacts in your area.
Service safety summary
Only qualied personnel should perform service procedures. Read this Service safety summary before performing any service procedures.
Do not service alone. Do not perform internal service or adjustments of this product unless another person capable of rendering rst aid and resuscitation is present.
Disconnect power. To avoid electric shock, switch off the instrument power, then disconnec
Use care when servicing with power on. Dangerous voltages or currents may exist in this product. Disconnect power, remove battery (if applicable), and disconnect test leads before removing protective panels, soldering, or replacing components.
To avoid electric shock, do not touch exposed connections.
t the power cord from the mains power.
AWG70000A Series Upgrades 1
Service safety summary
2 AWG70000A Series Upgrades
Upgrade kit overview
This document provides instructions for performing hardware and/or software and option key upgrades on the following Tektronix products:
AWG70001A Arbitrary Waveform Generators
AWG70002A Arbitrary Waveform Generators
Upgrade kits covered by
these instr
AWG70001A Upgrades
AWG701AUP 01 Increases the waveform record length from 2 GSamples to 16 GSamples Option key only
AWG701AUP 03
AWG701AUP SSD-01
numbers
(Serial B019999 and below)
AWG701AUP SSD-02
(Serial numbers
00 and above)
B0200
01AUP SSD-03
AWG7
(Serial numbers B019999 and below)
uctions
The following table lists the available product upgrades supported by this document.
Description Upgrade type
Adds sequencing
Provides an additional (or replacement) preprogrammed Solid State Drive with the numbers B019999 and below.
This drive can be used to:
Provides an additional (or replacement) preprogrammed Solid State Drive with the Microsoft Windows 10 operating system for instruments with serial numbe
This drive can be used to:
Prov with the Microsoft Windows 10 operating system for instruments with serial numbers B019999 and below.
Thi
Microsoft Windows 7 operating system for instruments with serial
provi
revert an instrument with the Windows 10 OS to the Windows 7 OS.
rs B020000 and above.
provide a n additional (or replacement) SSD with the Windows 10 OS.
conv
ides an additional (or replacement) preprogrammed Solid State Drive
s drive can be used to:
provide a n additional (or replacement) SSD with the Windows 10 OS.
convert an instrument with the W indows 7 OS to the Windows 7 OS.
Some upgrades only require an option key to enable the new features.
Option key only
Hardware included
de an additional (or replacement) SSD with the Windows 7 OS.
Hardwa
ert an instrument with the Windows 7 OS to the Windows 10 OS.
Hardware included
re included
AWG70002A Upgrades
AWG702AUP 01 Increases the waveform record length from 2 G Samples to 8 GSamples
G702AUP 03
AW
WG702AUP 0816
A
WG702AUP 0825
A
AWG702AUP 1625 Increases the sampling rate from 16 GS /s to 25 GS/s Option key only
Description Upgrade type
Option key only
both channels
on
Adds sequencing
ncreases the sampling rate from 8 GS/s to 16 GS/s
I
ncreases the sampling rate from 8 GS/s to 25 GS/s
I
tion key only
Op
ption key only
O
ption key only
O
AWG70000A Series Upgrades 3
Upgrade kit overview
AWG70002A Upgrades
AWG701AUP SSD-01
(Serial numbers B019999 and be
AWG701AUP S
(Serial numbers B020000 and above)
AWG701AUP SSD-03
(Serial n B019999 and below)
low)
SD-02
umbers
Description Upgrade type
Provides an additional (or replacement) preprogrammed Solid State Drive with the Microsoft Windows 7 operating system for instruments with serial numbers B0199
This drive can be used to:
provide an additional (or replacement) SSD with the Windows 7 OS.
revert an in
Provides an with the Microsoft Windows 10 operating system for instruments with serial numbers B020000 and above.
This drive
provide an additional (or replacement) SSD with the Windows 10 OS.
convert an instrument with the Windows 7 OS to the Windows 10 OS.
Provides an additional (or replacement) preprogrammed Solid State Drive with the M numbers B019999 and below.
This drive can be used to:
provid
convert an instrument with the Windows 7 OS to the Windows 7 OS.
99 and below.
strument with the Windows 10 OS to the Windows 7 OS.
additional (or replacement) preprogrammed Solid State Drive
canbeusedto:
icrosoft Windows 10 operating s ystem for instruments with serial
e an additional (or replacement) SS D with the Windows 10 OS.
Hardware incl
Hardware included
Hardware included
For a list of available options, see the Tektronix website (www.tektronix.com) or your Tektronix representative.
uded
Kit parts lists
Option key only upgrades
AWG701AUP SSD-0x and
AWG702AUP SSD-0x
Some upgrades only require a new option key to enable the new features or enhancements. These types of kits contains the following ite
Tektronix part number Qty. Description
N/A
N/A
075-1049-XX 1
1
1
LABEL, OPTION KEY INFORMATION
Apply label to rear panel
LABEL, ECCN (RED)
Only supplied with:
AWG701AUP 03
AWG702AUP 03
Apply label to rear panel
MANUAL, KIT INSTRUCTIONS
ms:
These upgrades provide a preprogrammed solid state drive to use as either a secondary hard drive, a replacement for a failed hard drive, and to change operating systems. The kit contains the following items:
4 AWG70000A Series Upgrades
Upgrade kit overview
Tektronix part number Qty. Description
211-1081-XX
335-2612-XX
One of the following:
650-5585-X
850-0385-XX
850-0390-XX
407-5641-XX
075-1049-XX 1
1
The hard drive and the mechanical sled components are pre-assembled.
2
The hard drive delivered with the upgrade kit is based on the hard drive upgrade purchased.
1
4
SCREW, MACH IN E; M3 X 0.5 X 3.5MM, FLAT WAFER HD W/SERRATIONS STRESS RELIEVED, PHL, ZINC PLATED STEEL
1
1
MARKER, IDEN
T; HD ADAPTER (SLED); SAFETY
CONTROLLED
1
HARD DRIVE, PROGRAMMED; SOLID STATE DRIVE PROGRAMMED W/ OS & APP SW
1,2
X
1,2
1,2
The Operati option.
The Application software is the most current version available
1
1
ASSEMBLY
MANUAL, K
ng System installed is dependent on the SSD
.
, SLED, HARD DRIVE MOUNT (REMOVABLE)
IT INSTRUCTIONS
AWG70000A Series Upgrades 5
Upgrade kit installation
Upgrade kit installation
Refer to the one (or more) of the following installation sections pertaining to the upgrade(s) you are installing.
Minimum tool and equipment list
No special tools are required to install any of the upgrade kits covered by these installati
Option key only upgrades
on instructions.
To ins t a l this kit. This unique key number is valid only for the specic model number and serial number of your instrument; it will not work on any other instrument. This single key number enables all valid options for your instrument, those that were factory installed and any others that you may have already purchased. In other words, this new key number supersedes any previous key numbers that you may
CAUTION. To avoid losing your options, do not misplace the label that is included
with this kit. This label contains the option installation key number and should be installed on the rear panel of the instrument for future reference. Apply the new label over the existing option key label.
As a backup, you may want to copy the key number and save it with the other important papers for your instrument. If you ever need to re-enable the option, you will need to re-enter this key number.
1. Power on the instrument.
2. Select Utilities from the workspace tabs.
3. Select About my AWG to display the current option information and system
l these types of options, you need the key number that is provided with
already have.
information.
6 AWG70000A Series Upgrades
Upgrade kit installation
4. Click Install Options to start the upgrade installation process.
5. Click Continue from the Install Upgrades introduction screen.
6. Enter the option key provided by Tektronix, and follow the on-screen
tructions to install the option.
ins
7. Power off the instrument, then power back on.
8. Select Utilities from the workspace tabs.
9. Select About my AWG to display the current option information and system
information.
10. Verify the new option is listed.
AWG70000A Series Upgrades 7
Upgrade kit installation
11. Apply the new option key label over the existing key label on the rear panel of the instrument.
12. Option 03 upgrades (adding sequencing): You must apply the red ECCN label to the rear panel of the instrument.
8 AWG70000A Series Upgrades
Upgrade kit installation
AWG701AUP SSD AWG702AUP SSD
-0x and
-0x installation
NOTE. Before installing the new hard drive, use an external backup device to
back up any les on your instrument for use on the new hard drive.
Install the hard drive using the following procedure:
1. Power off the instrument.
2. Loosen the thumb screws and remove the exist
NOTE. The hard drive and hard drive sled components are pre-assembled.
3. Install the new hard drive, and then tighten the thumb screws to secure the drive in the instrument.
4. Power on the instrument to verify operation.
NOTE. If the hard drive contains Microsoft Windows 10, activation is required.
ing hard drive.
Windows 10 activation
AWG70000A Series Upgrades 9
The version Deferred Activation mode. Microsoft has a default activation method that requires a connection to the Internet. If you do not have a connection, you can activate Windows by phone or you can continue to operate in Deferred Activation mode.
First time activation. You can activate Windows 10 two ways.
of Microsoft Windows 10 included on the hard drive is shipped in
Upgrade kit installation
1. Connect to the I go to System Properties to connect and activate.
2. Call Microsof Contact information and a unique activation code (installation ID) will appear in a pop up window.
Activation with removable drives. If the SSD is removed from one instrument and inserted into another instrument, the activation process needs to be run again. If instrumen Windows watermark is displayed on the screen. To a ctivate Windows and remove the watermark, you must connect to the Internet or call Microsoft.
t 2 is not connected to the Internet, the activation fails and an Activate
nternet. Windows will automatically activate. You can also
t and speak with a representative to activate Windows 10.
10 AWG70000A Series Upgrades
Verify instrument software version
Verify instru
ment software version
Tektronix re your instrument.
1. Select Util Software Version number.
2. Use your We
3. Search for your instrument’s model number and follow the link to the software.
4. If the installed software is older than that available, download the software.
5. Follow the instructions on the Web page to install the software.
NOTE. Updating the instrument software does not impact installed option keys.
commends to update to the latest available application software for
ities > About my AWG. Under System Information, note the
b browser to go to: www.tektronix.com/software.
AWG70000A Series Upgrades 11
Loading...