Tektronix AWG70001B, AWG70002B Performance Verification
xx
AWG70001B and AWG70002B
Arbitrary Waveform Generators
Specifications and Performance Verification
Includes
ZZZ
AWGSYNC01 Synchronization Hub Specifications
Technical Reference
*P077145300*
077-1453-00
xx
AWG70001B and AWG70002B
Arbitrary Waveform Generators
Specifications and Performance Verification
Includes
ZZZ
AWGSYNC01 Synchronization Hub Specifications
Technical Reference
Warning
The servicing instructions ar
only. To avoid personal injury, do not perform any servicing
unless you are qualified to do s
before performing service.
www.tek.com
e for use by qualified personnel
o. Refer to all safety summaries
077-1453-00
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14150 SW Karl Braun Drive
P.O . Box 50 0
Beaverto
USA
For product information, sales, service, and technical support:
n, OR 97077
In North America, call 1-800-833-9200.
Worldwide, visit www.tek.com to find contacts in your area.
Table of Contents
General safety summary ........................................................................................... v
Servicesafety summary.......................................................................................... vii
Preface.............................................................................................................. ix
Related doc
Specifications ....................................................................................................... 1
Performance conditions ....................................................................................... 1
Electrical specifications....................................................................................... 2
Mechanicalcharacteristics................................................................................... 20
Environmental characteristics............................................................................... 22
AWGSYNC
Electrical specifications...................................................................................... 23
Mechanicalcharacteristics................................................................................... 26
Performanceverification procedures ............................................................................ 27
Input andoutput options ..................................................................................... 28
Instrument interface overview............................................................................... 29
f procedures ................................................................................................... 33
Brie
Diagnostics .................................................................................................... 33
Calibration..................................................................................................... 34
Functional test................................................................................................. 36
Performancetests.................................................................................................. 49
Prerequisites................................................................................................... 49
quired equipment .......................................................................................... 49
Re
10 MHzreferencefrequencyaccuracy ..................................................................... 51
Analog amplitude accuracy .. . ... ... . .. . ... ... . ... ... . .. . ... ... . ... .......................................... 52
Marker high andlow level accuracy........................................................................ 56
Testrecord..................................................................................................... 61
uments............................................................................................ ix
01 ..................................................................................................... 23
AWG70000B Series and AWGSYNC01 Technical Reference i
Table of Contents
List of Figure
Figure 1: Dimensions and minimum cooling clearances...................................................... 21
Figure 2: Di
Figure 3: Calibration dialog box................................................................................. 35
Figure 4: Equipment connections to check the analog and marker outputs.. . .............................. 37
Figure 5: Output waveform from the channel, marker 1, and marker 2 connectors ....................... 39
Figure 6: Equipment connections to checkthe AC output.................................................... 40
Figure 7: 1 GHz output waveform – no filter .................................................................. 42
Figure 8:
Figure 9: 11 GHz output waveform ............................................................................. 44
Figure 10: 14 GHz output waveform............................................................................ 45
Figure 11: Equipment connection to check the triggered outputs ... . ... . .................................... 46
Figure 12: Equipment connection to verify the 10 MHz reference frequency accuracy................... 51
Figure 13: Equipment connection for measuring the termination resistance ............................... 52
e 14: Equipment connection for checking the analog amplitude accuracy . .......................... 53
Figur
Figure 15: Equipment connection to verify the marker high and low level accuracy...................... 56
agnostics dialog box ................................................................................ 34
1 GHz output waveform – Filter set to Low Pass .. ... . ... ... . .. . ... ... . ... ........................ 43
s
ii AWG70000B Series and AWGSYNC01 Technical Reference
List of Tables
Table i: Related documents....................................................................................... ix
Table 1: Run mode ................................................................................................. 2
Table 2: Arbitrary waveform...................................................................................... 2
Table 3: Sample clock generator.................................................................................. 3
Table 4: Analog output............................................................................................. 3
Table 5: SFDR, AWG70001B and AWG70002B operating at 25 GS/s
Table 6: SFDR, AWG70001B operating at 50 GS/s
Table 7: SFDR, AWG70002B operating at 8 GS/s
Table 8: SFDR, AWG70002B operating at 16 GS/s
Table 9: Phase noise with jitter reduction, AWG70001B operating at 50 GS/s ............................. 8
Table 10: Phase noise with jitter reduction, AWG70001B and AWG70002B operatingat 25 GS/s...... 9
Table 11: Phase noise with jitter reduction, AWG70002B operating at 8 GS/s ............................. 9
Table 12: Phase noise with jitter reduction, AWG70002B operating at 16 GS/s............................ 9
Table 13: Phase noise without jitter reduction, AWG70001B operating at 49.998998 GS/s.............. 10
Table 14: Phase noise without jitter reduction, AWG70001B and AWG70002B operating at
24.998998 GS/s ............................................................................................... 10
Table 15: Phase noise without jitter reduction, AWG70002B operating at 7.998997998 GS/s........... 10
Table 16: Phase noise without jitter reduction, AWG70002B operating at 15.998997998 GS/s .. ... . ... 10
Table 17: AC analogoutput (AWG70001B,Option AC)..................................................... 11
Table 18: Marker output .......................................................................................... 13
Table 19: Clock output............................................................................................ 14
Table 20: Clock input ............................................................................................. 14
Table 21: Trigger input ........................................................................................... 14
Table 22: Reference clockinput ................................................................................. 15
Table 23: Sync clockoutput...................................................................................... 16
Table 24: Sequencer............................................................................................... 16
Table 25: Pattern Jump Input..................................................................................... 17
Table 26: Streaming ID connector............................................................................... 18
Table 27: Auxout connectors.................................................................................... 18
Table 28: 10 MHz reference clock output ...................................................................... 19
Table 29: Sync port................................................................................................ 19
Table 30: CPUmodule and peripheraldevices................................................................. 19
Table 31: Display.................................................................................................. 19
Table 32: Power supply........................................................................................... 20
Table 33: Mechanicalcharacteristics............................................................................ 20
Table 34: Environmental characteristics ........................................................................ 22
Table 35: Electricalspecifications............................................................................... 23
Table 36: Power supply........................................................................................... 26
Table of Contents
1
.................................... 7
1
.......................................................... 7
1
............................................................ 8
1
.......................................................... 8
AWG70000B Series and AWGSYNC01 Technical Reference iii
Table of Contents
Table 37: Mecha
Table 38: Required equipment for the functional test . .... ... . .. . ... . ......................................... 36
Table 39: Test waveforms ........................................................................................ 36
Table 40: Required equipment for performance tests ......................................................... 49
Table 41: Performance test waveforms ......................................................................... 50
Table 42: Analog amplitude accuracy. ... . .. . ... ... . ... ... . ... ... . .. . ........................................... 54
Table 43: Ma
Table 44: Marker low level accuracy............................................................................ 59
nical characteristics............................................................................ 26
rker high level accuracy........................................................................... 57
iv AWG70000B Series and AWGSYNC01 Technical Reference
General safety summary
General safet
To avoid fir
e or personal
injury
y summary
Review the fo
this product or any products connected to it.
To avoid pot
Only qualified personnel should perform service procedures.
Use proper
certified for the country of use.
Ground th
of the power cord. To avoid electric shock, the grounding conductor must be
connected to earth ground. Before making connections to the input or output
terminals of the product, ensure that the product is properly grounded.
Observe all terminal ratings. To avoid fire or shock hazard, observe all ratings
and markings on the product. Consult the product manual for further ratings
information before making connections to the product.
Do not apply a potential to any terminal, including the common terminal, that
exceeds the maximum rating of that terminal.
llowing safety precautions to avoid injury and prevent damage to
ential hazards, use this product only as specified.
power cord. Use only the power cord specified for this product and
e product. This product is grounded through the grounding conductor
Power disconnect. The power cord disconnects the product from the power source.
Do not block the power cord; it must remain accessible to the user at all times.
Do not operate without covers. Do not operate this product with covers or panels
removed.
Do not operate with suspected failures. If you suspect that there is damage to this
product, have it inspected by qualified service personnel.
Avoid exposed circuitry. Do not touch exposed connections and components when
power is present.
Do not operate in wet/damp conditions.
Do not operate in an explosive atmosphere.
Keep product surfaces clean and dry.
Provide proper ventilation. Refer to the manual's installation instructions for details
on installing the product so it has proper ventilation.
AWG70000B Series and AWGSYNC01 Technical Reference v
General safety summary
Termsinthismanual
Symbols and terms on the
product
These terms may
WARNING. Warning statements identify conditions or practices that could result
in injury or loss of life.
CAUTION. Caution statements identify conditions or practices that could result in
damage to this product or other property.
These terms may appear on the product:
DANGER in
the marking.
WAR NI NG
read the marking.
CAUTIO
The following symbol(s) may appear on the product:
appear in this manual:
dicates an injury hazard immediately accessible as you read
indicates an injury hazard not immediately accessible as you
N indicates a hazard to property including the product.
vi AWG70000B Series and AWGSYNC01 Technical Reference
Service safety summary
Service safet
ysummary
Only qualifie
safety summary and the General safety summary before performing any service
procedures.
Do not service alone. Do not perform internal service or adjustments of this
product unless another person capable of rendering first aid and resuscitation is
present.
Disconnect power. To avoid electric shock, switch off the instrument power, then
disconnect the power cord from the mains power.
Use care when servicing with power on. Dangerous voltages or currents may exist
in this p
test leads before removing protective panels, soldering, or replacing components.
To avoi
d personnel should perform service procedures. Read this Service
roduct. Disconnect power, remove battery (if applicable), and disconnect
d electric shock, do not touch exposed connections.
AWG70000B Series and AWGSYNC01 Technical Reference vii
Service safety summary
viii AWG70000B Series and AWGSYNC01 Technical Reference
Preface
Related documents
This manual contains specifications and performance verification procedures for
the AWG70000B Series Arbitrary Waveform Generators and the AWGSYNC01
Synchroniza
tion Hub.
The follow
ing user documents are also available for this product.
The documents are available for download from the Tektronix website.
Table i: R
Item Descript
AWG70000
Safety Manual
AWGSYNC01 Installation and Safety
Manual
AWG70000 Series Programmer
AWG7
(converted to PDF)
elated documents
B Series Installation and
0000 Series Help System
ion
This docu
how to install the AWG70000B generators.
Tektronix Part Number 0713597xx
This document provides safety information
and how
Synchronization Hub.
Tektronix Part Number 0713292xx
This document provides programming
information.
07714
This
AWG70000 help system.
Tektronix Part Number 0771446xx
ment provides safety information and
to install the AWGSYNC01
52xx
document is a PDF output of the entire
AWG70000B Series and AWGSYNC01 Technical Reference ix
Preface
x AWG70000B Series and AWGSYNC01 Technical Reference
Specifications
This section contains the specifications for the AWG70000B series Arbitrary
Waveform Generators and the AWGSYNC01 Synchronization Hub. The
generators a
AWGSYNC01 information.
re covered together in the first part, followed by the separate
Performance conditions
All specific
marked with the
To meet specifications, the following conditions must be met:
The instr
between +20 °C and +30 °C.
The inst
Table 34 on page 22.)
The ins
specifications. (See Table 32 on page 20.)
The in
within the specified operating temperature range.
ations are typical unless noted as warranted. Warranted specifications
symbol are checked in this manual.
ument must have been calibrated/adjusted at an ambient temperature
rument must be operating within the environmental limits. (See
trument must be powered from a source that meets the power
strument must have been operating continuously for at least 20 minutes
AWG70000B Series and AWGSYNC01 Technical Reference 1
Specifications
Electrical sp
ecifications
Table 1: Run mode
Characteris
Continuous m
Triggered mode
Triggered
tics
ode
continuous mode
Description
A waveform is
A waveform i
the instrument waits for the next trigger signal.
A waveform is output continuously after a trigger signal is applied.
output continuously.
s output only once when a trigger signal is applied. After the waveform is output,
Table 2: Arbitrary waveform
Characteristics Description
Waveform memory
AWG70001B
Standard
With optional memory expansion
AWG70002B
Standard
With optional memory expansion
Minimum waveform size
AWG70001B
Continuous run mode
Triggered run modes 4800 points
AWG70002B
Continuous run mode
Triggered run modes 2400 points
Waveform granularity
AWG70001B
Continuous run mode
Triggered run modes 2 points
AWG70002B
Continuous run mode
Triggered run modes 1 point
Waveform interleaving Interleaving is performed without zeroing.
AWG70001B Non-interleaved when ≤25 GS/s, interleaved when >25 GS/s
AWG70002B
DAC resolution
2G(
16 G (
32 G (
2G(
16 G (
1 point
1 point
2 points
1 point
Non-interleaved at all sample rates
8-bit, 9-bit, or 10-bit
) samples
) samples when sample rate is ≤25 GS/s (non-interleaved)
) samples when sample rate is >25 GS/s (interleaved)
) samples per channel
) samples per channel
10-bit mode, markers are not available
9-bit mode, marker M1 is available
8-bit mode, markers M1 and M2 are available
2 AWG70000B Series and AWGSYNC01 Technical Reference
Specifications
Table 3: Sample
clock generator
Characteristics Description
Range
AWG70001B Op
AWG70002B O
AWG70002B O
AWG70002B
Option 208
tion 150
ption 225
ption 216
1.49 kS/s to 5
1.49 kS/s to
1.49 kS/s to
1.49 kS/s t
0GS/s
25 GS/s
16 GS/s
o8GS/s
Resolution
With jitter reduction 3 digits
Without j
itter reduction
8digits
Phase adjustment Used to manually align the outputs with other generators or instruments.
Range
Resolution
-10,800° to +10,800°
1°
Table 4: Analog output
Characteristics Description
Connector type Aeroflex/Weinschel Planar Crown Universal Connector System with SMA female adapter
Number of outputs AWG70001B: 1
AWG70002B: 2
Type of outputs (+) and (–) complementary output
ON/OFF control Independent control for each analog output complementary pair
Output impedance 50 Ω
VSWR
AWG70001B DC to ≤5 GHz = 1.32:1
>5 GHz to ≤10 GHz = 1.52:1
>10 GHz to 20 GHz = 1.73:1
AWG70002B DC to 10 GHz = 1.61:1
Amplitude
Range
Resolution 1 mV
DC accuracy (warranted)
Amplitude flatness Flatness is measured as the deviation from the ideal sin(x)/x response curve of the DAC at the
AWG70001B +1.8 dB to –1.8 dB up to 10 GHz
AWG70002B +0.8 dB to –1.5 dB up to 10 GHz
Independent control for each channel
0.25 V
0.5 V
p-p
to 1.0 V
p-p
to 0.5 V
into 50 Ω single-ended
p-p
into 100 Ω differential
p-p
±(2% of amplitude + 1 mV)
specified sample rate. The response is mathematically removed from the measured data.
+1.8 dB to –3 dB from 10 GHz to 15 GHz
AWG70000B Series and AWGSYNC01 Technical Reference 3
Specifications
Table 4 : Analog output (cont.)
Characteristics Description
Sin(x)/x bandwidth The sin(x)/x bandwidth can be solved for using the following equation:
20 * log (sin(x)/x) = -3
For interleaved waveforms: x = 2π * fout ÷ fsample
For non-interleaved waveforms: x = π * fout ÷ fsample
fsample = sample rate
fout = sin(x)/x bandwidth
AWG70001B ≤ 25 GS/s (non-interleaved): 11.1 GHz × fsample ÷ 25 GS/s
> 25 GS/s (interleaved): 11.1 GHz × fsample ÷ 50 GS/s
AWG70002B 11.1 GHz * fsample ÷ 25 G S/s
Analog bandwidth
AWG70001B 15 GHz at 50 GS/s
AWG70002B 13.5 GHz at 25 GS/s
Rise/fall time When operating in interleaved mode, rising and falling edges are c reated using two sample
AWG70001B ≤ 25 GS/s: < 23 ps
AWG70002B
Aberrations
Skew between (+) and (-) outputs
Analog bandwidth is measured with the ideal sin(x)/x response curve of the DAC
mathematically removed from the measured data.
points. As a result, the rise/fall time is dependent on the sample rate.
at 30 GS/s: < 42 ps
at 40 GS/s: < 32 ps
at 50 GS/s: < 27 ps
<22ps
<18%
for the first 100 ps following the step transition with 100% reference at 1 ns.
p-p
<5ps
4 AWG70000B Series and AWGSYNC01 Technical Reference
Table 4: Analog output (cont.)
Characteristics Description
Harmonic distortion Measured with a balun.
AWG70001B and
AWG70002B
Operating at 25 GS/s
AWG70002B
Operating at 8 GS/s
Operating at 16 GS/s
SFDR
AWG70001B and
.AWG70002B operating
at 25 GSs
AWG70001B operating at
50 GSs
AWG70002B operating at
8GSs
AWG70002B operating at
16 GSs
Output Frequency
<2 GHz
2GHz–6GHz
>6 GHz
<1 GHz:
1GHz–2GHz
>2 GHz
Output Frequency
<1 GHz
1GHz–3.2GHz
<1 GHz:
1GHz–3.2GHz
<1 GHz
1GHz–4GHz
>4 GHz
<1 GHz:
1GHz–2GHz
>2 GHz
(See Table 5 on page 7.)
(See Table 6 on page 7.)
(See Table 7 on page 8.)
(See Table 8 on page 8.)
Specifications
2nd harmonic
< –60 dBc
< –50 dBc
< –42 dBc
3rd harmonic
< –60 dBc
< –50 dBc
< –40 dBc
2nd harmonic
< –60 dBc
< –55 dBc
3rd harmonic
< -60 dBc
< –50 dBc
2nd harmonic
< –60 dBc
< –55 dBc
< –50 dBc
3rd harmonic
< –60 dBc
< –50 dBc
< –40 dBc
AWG70000B Series and AWGSYNC01 Technical Reference 5
Specifications
Table 4 : Analog output (cont.)
Characteristics Description
ENOB
AWG70001B 4.6 bits at 14.990 GHz
All noise and distortion DC - 20 GHz
AWG70002B 5.6 bits at 9.990 GHz
All noise and distortion DC - 12.5 GHz
Phase noise with jitter reduction
AWG70001B operating at
50 GSs
AWG70001B and
AWG70002B operating at
25 GSs
AWG70002B operating at
8GSs
AWG70002B operating at
16 GSs
Phase noise without jitter reduction
AWG70001B operating at
49.998998 GSs
AWG70001B and
AWG70002B operating at
24.998998 GSs
AWG70002B operating at
7.998997998 GSs
AWG70002B operating at
15.998997998 GSs
Random jitter on clock pattern 0.25 ps
Total jitter on random pattern 10 ps
Interleave adjustment
(AWG70001B only)
Phase adjustment range
Phase adjustment resolution
Amplitude matching range
Inter-channel skew control
(AWG70002B only)
Range –100 ps to +100 ps
Resolution 1 ps
Accuracy
(See Table 9 on page 8.)
(See Table 10 on page 9.)
(See Table 11 on page 9.)
(See Table 12 on page 9.)
(See Table 13 on page 10.)
(See Table 14.)
(See Table 15 on page 10.)
(See Table 16 on page 10.)
rms
Using 0101 clock pattern with 500 mV
p-p
Using PRBS pattern with 500 mV
-180° to +180°
1°
±10% of amplitude setting
±5 ps
amplitude.
p-p
amplitude, measured at Bit Error Rate of 1e
p-p
-12
.
6 AWG70000B Series and AWGSYNC01 Technical Reference
Specifications
Table 5: SFDR, A
Analog channel
output frequency
100 MHz
DC – 500 MHz DC – 500 MHz
DC–1GHz DC–1GHz
DC–2GHz DC–2GHz
DC–3GHz DC–3GHz
DC–5GHz DC–5GHz
5–6GHz 5–6GHz
6–7GHz 6–7GHz
7–8GHz 7–8GHz
8–10GHz 8–10GHz
1
Measured with a balun, excluding harmonics.
WG70001B and AWG70002B operating at 25 GS/s
In band performance
measured across Specification
DC – 1 GHz
–80 dBc
–70 dBc
–63 dBc
–62 dBc
–60 dBc
–52 dBc
–52 dBc
–42 dBc
–55 dBc
–50 dBc
Table 6: SFDR, AWG70001B operating at 50 GS/s
Analog channel
tfrequency
outpu
100 MHz
500 MHz
DC –
1GHz
DC –
–2GHz
DC
–3GHz
DC
C–5GHz
D
–6GHz
5
6–7GHz 6–7GHz
7–8GHz 7–8GHz
8–10GHz 8–10GHz
10–12GHz 10–12GHz
12–13GHz 12–13GHz
13–14GHz 13–14GHz
14–16GHz 14–16GHz
In band performance
red across
measu
GHz
DC – 1
500 MHz
DC –
1GHz
DC –
–2 GHz
DC
–3 GHz
DC
C–5GHz
D
–6GHz
5
Speci
–80 dBc
–70 dBc
–63 dBc
–62 dBc
–60 dBc
–52 dBc
–52 dBc
–42 dBc
–60 dBc
–50 dBc
–53 dBc
–22 dBc
–54 dBc
–46 dBc
1
fication
1
Adjacent band
performance
measured across Specification
DC – 10 GHz
DC – 1.5 GHz
DC – 3 GHz
DC – 6 GHz
DC – 6 GHz
DC – 6 GHz
3–9GHz
4–10GHz
6 – 12.5 GHz
6 – 12.5 GHz
–72 dBc
–66 dBc
–63 dBc
–60 dBc
–52 dBc
–52 dBc
–40 dBc
–42 dBc
–50 dBc
–50 dBc
Adjacent band
performance
red across
measu
0GHz
DC – 1
1.5 GHz
DC –
3GHz
DC –
–6GHz
DC
–6GHz
DC
C–6GHz
D
–9GHz
3
4–10GHz
6–12.5GHz
6–12.5GHz
6–12.5GHz
10 – 15 GHz
11–16GHz
13 – 18 GHz
Speci
–72 dBc
–66 dBc
–63 dBc
–60 dBc
–52 dBc
–52 dBc
–40 dBc
–42 dBc
–52 dBc
–52 dBc
–50 dBc
–22 dBc
–20 dBc
–38 dBc
fication
AWG70000B Series and AWGSYNC01 Technical Reference 7
Specifications
Table 6: SFDR, AWG70001B operating at 50 GS/s1(cont.)
Analog channel
output frequency
16 – 18.5 GHz 16 – 18.5 GHz
18.5–20GHz 18.5–20GHz
1
Measured with a balun, excluding harmonics.
In band performance
measured across Specification
–42 dBc
–28 dBc
Adjacent band
performance
measured across Specification
14 – 20 GHz
16 – 20 GHz
–30 dBc
–24 dBc
Table 7: SFDR, AWG70002B operating at 8 GS/s
Analog channel
output frequency
100 MHz
0 – 500 MHz
DC–1GHz DC–1GHz
DC–2GHz DC–2GHz
DC – 2.6 GHz DC –2.6 GHz
DC–3.2GHz DC–3.2GHz
1
Measured with a balun, excluding harmonics.
In band performance
measured across Specification
DC–1GHz
DC – 500 MHz
–80 dBc
–68 dBc
–63 dBc
–60 dBc
–55 dBc
–47 dBc
Table 8: SFDR, AWG70002B operating at 16 GS/s
Analog channel
output frequency
100 MHz
0 – 500 MHz
DC–1GHz DC–1GHz
DC–2GHz DC–2GHz
DC – 3.5 GHz DC –3.5 GHz
3.5 – 4.5 GHz 3.5 – 4.5 GHz
4.5 – 6.4 GHz 4.5 – 6.4 GHz
1
Measured w
ith a balun, excluding harmonics.
In band performance
measured across Specification
DC–1GHz
DC – 500 MHz
–80 dBc
–68 dBc
–62 dBc
–60 dBc
–57 dBc
–42 dBc
–52 dBc
1
Adjacent band
performance
measured across Specification
DC – 3 GHz
DC – 1.5 GHz
DC – 3 GHz
DC – 4 GHz
DC – 4 GHz
DC – 4 GHz
1
–72 dBc
–66 dBc
–63 dBc
–60 dBc
–52 dBc
–47 dBc
Adjacent band
performance
measured across Specification
DC – 3 GHz
DC – 1.5 GHz
DC – 3 GHz
DC – 6 GHz
DC – 8 GHz
DC – 8 GHz
DC – 8 GHz
–72 dBc
–66 dBc
–63 dBc
–58 dBc
–40 dBc
–42 dBc
–42 dBc
Table 9: Phase noise with jitter reduction, AWG70001B operating at 50 GS/s
Analog output frequency
Offset 100 MHz 1 GHz 10 GHz 16 GHz
100 Hz
1kHz
10 kHz
100 kHz
–116 dBc/Hz –94 dBc/Hz –75 dBc/Hz –70 dBc/Hz
–134 dBc/Hz –116 dBc/Hz –95 dBc/Hz –91 dBc/Hz
–136 dBc/Hz –119 dBc/Hz –101 dBc/Hz –96 dBc/Hz
–138 dBc/Hz –118 dBc/Hz –99 dBc/Hz –96 dBc/Hz
8 AWG70000B Series and AWGSYNC01 Technical Reference
Table 9: Phase noise with jitter reduction, AWG70001B operating at 50 GS/s (cont.)
Analog output frequency
Offset 100 MHz 1 GHz 10 GHz 16 GHz
1MHz
10 MHz
–150 dBc/Hz –132 dBc/Hz –112 dBc/Hz –108 dBc/Hz
–156 dBc/Hz –157 dBc/Hz –138 dBc/Hz –130 dBc/Hz
Table 10: Phase noise with jitter reduction, AWG70001B and AWG70002B operating at 25 GS/s
Analog output frequency
Offset 100 MHz 1 GHz 10 GHz
100 Hz
1kHz
10 kHz
100 kHz
1MHz
10 MHz
–115 dBc/Hz –95 dBc/Hz –76 dBc/Hz
–134 dBc/Hz –115 dBc/Hz –86 dBc/Hz
–138 dBc/Hz –121 dBc/Hz –102 dBc/Hz
–138 dBc/Hz –118 dBc/Hz –100 dBc/Hz
–150 dBc/Hz –132 dBc/Hz –113 dBc/Hz
–155 dBc/Hz –157 dBc/Hz –138 dBc/Hz
Specifications
Table 11: Phase noise with jitter reduction, AWG70002B operating at 8 GS/s
Analog output frequency
Offset 100 MHz 1 GHz 2 GHz 3 GHz
100 Hz
1kHz
10 kHz
100 kHz
1MHz
10 MHz
–110 dBc/Hz –89 dBc/Hz –83 dBc/Hz –80 dBc/Hz
–127 dBc / Hz –109 dBc / Hz –102 dBc / Hz –99 dBc / Hz
–134 dBc/Hz –115 dBc/Hz –108 dBc/Hz –107 dBc/Hz
–134 dBc/Hz –113 dBc/Hz –106 dBc/Hz –104 dBc/Hz
–142 dBc/Hz –121 dBc/Hz –114 dBc/Hz –112 dBc/Hz
–154 dBc/Hz –149 dBc/Hz –144 dBc/Hz –141 dBc/Hz
Table 12: Phase noise with jitter reduction, AWG70002B operating at 16 GS/s
Analog output frequency
Offset 100 MHz 1 GHz 2 GHz 3 GHz 4 GHz
100 Hz
1kHz
10 kHz
100 kHz
1MHz
10 MHz
–112 dBc/Hz –90 dBc/Hz –87 dBc/Hz –82 dBc/Hz –80 dBc/Hz
–128 dBc / H z –109 dBc / Hz –103 dBc / Hz –99 dBc / Hz –97 dBc / Hz
–134 dBc/Hz –116 dBc/Hz –110 dBc/Hz –106 dBc/Hz –104 dBc/Hz
–133 dBc/Hz –113 dBc/Hz –108 dBc/Hz –104 dBc/Hz –101 dBc/Hz
–141 dBc/Hz –122 dBc/Hz –116 dBc/Hz –113 dBc/Hz –110 dBc/Hz
–154 dBc/Hz –150 dBc/Hz –147 dBc/Hz –143 dBc/Hz –140 dBc/Hz
AWG70000B Series and AWGSYNC01 Technical Reference 9
Specifications
Table 13: Phase
Offset 100 MHz 1 GHz 10 GHz 16 GHz
100 Hz
1kHz
10 kHz
100 kHz
1MHz
10 MHz
noise without jitter reduction, AWG70001B operating at 49.998998 GS/s
Analog output frequency
–110 dBc/Hz –89 dBc/Hz –69 dBc/Hz –67 dBc/Hz
–125 dBc/Hz –105 dBc/Hz –84 dBc/Hz –82 dBc/Hz
–130 dBc/Hz –110 dBc/Hz –94 dBc/Hz –89 dBc/Hz
–126 dBc/Hz –106 dBc/Hz –89 dBc/Hz –85 dBc/Hz
–139 dBc/Hz –119 dBc/Hz –104 dBc/Hz –100 dBc/Hz
–145 dBc/Hz –128 dBc/Hz –111 dBc/Hz –106 dBc/Hz
Table 14: Phase noise without jitter reduction, AWG70001B and AWG70002B operating at 24.998998 GS/s
Analog outp ut frequency
Offset 100 MHz 1 GHz 10 GHz
100 Hz
1kHz
10 kHz
100 kHz
1MHz
10 MHz
–104 dBc/Hz –92 dBc/Hz –74 dBc/Hz
–124 dBc/Hz –105 dBc/Hz –83 dBc/Hz
–130 dBc/Hz –111 dBc/Hz –93 dBc/Hz
–126 dBc/Hz –106 dBc/Hz –89 dBc/Hz
–131 dBc/Hz –122 dBc/Hz –104 dBc/Hz
–142 dBc/Hz –129 dBc/Hz –109 dBc/Hz
Table 15: Phase noise without jitter reduction, AWG70002B operating at 7.998997998 GS/s
alog output frequency
An
ffset
O
100 Hz
1kHz
10 kHz
100 kHz
1MHz
10 MHz
00 MHz
1
107 dBc/Hz
–
–120 dBc/Hz –99 dBc/Hz –92 dBc/Hz –90 dBc/Hz
–126 dBc/Hz –107 dBc/Hz –100 dBc/Hz –98 dBc/Hz
–125 dBc/Hz –105 dBc/Hz –98 dBc/Hz –96 dBc/Hz
–131 dBc/Hz –110 dBc/Hz –103 dBc/Hz –102 dBc/Hz
–141 dBc/Hz –121 dBc/Hz –113 dBc/Hz –112 dBc/Hz
GHz
1
88 dBc/Hz
–
GHz
2
83 dBc/Hz
–
GHz
3
79 dBc/Hz
–
Table 16: Phase noise without jitter reduction, AWG70002B operating at 15.998997998 GS/s
Analog output frequency
Offset 100 MHz 1 GHz 2 GHz 3 GHz 4 GHz
100 Hz
1kHz
10 kHz
100 kHz
1MHz
10 MHz
–106 dBc/Hz –88 dBc/Hz –84 dBc/Hz –79 dBc/Hz –75 dBc/Hz
–120 dBc/Hz –101 dBc/Hz –94 dBc/Hz –90 dBc/Hz –87 dBc/Hz
–126 dBc/Hz –107 dBc/Hz –102 dBc/Hz –98 dBc/Hz –96 dBc/Hz
–125 dBc/Hz –106 dBc/Hz –100 dBc/Hz –96 dBc/Hz –94 dBc/Hz
–135 dBc/Hz –115 dBc/Hz –109 dBc/Hz –106 dBc/Hz –103 dBc/Hz
–141 dBc/Hz –121 dBc/Hz –115 dBc/Hz –112 dBc/Hz –109 dBc/Hz
10 AWG70000B Series and AWGSYNC01 Technical Reference
Loading...