Tektronix AWG5002B, AWG5004B, AWG5012B, AWG5014B Performance Verification

xx
AWG5000B Series Arbitrary Waveform Generators
ZZZ
Specications and Performance Verication
Technical Reference
*P077248600*
077-2486-00
xx
AWG5000B Series Arbitrary Waveform Generators
ZZZ
Specications and Performance Verication
Technical Reference
www.tektronix.com
077-2486-00
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material. Specications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc. 14200 SW Karl Braun Drive P.O. B o x 5 0 0 Beaverto USA
For product information, sales, service, and technical support:
n, OR 97077
In North America, call 1-800-833-9200. Worl dwid e, vis it www.tektronix.com to nd contacts in your area.
Warranty
Tektronix warrants that this product will be free from defects in materials and workmanship for a period of one (1) year from the date of shipment. If any such product proves defective during this warranty period, Tektronix, at its option, either will repair the defective product without charge for parts and labor, or will provide a replacement in exchange for the defective product. Parts, modules and replacement products used by Tektroni modules and products become the property of Tektronix.
x for warranty work may be new or reconditioned to like new performance. All replaced parts,
In order to o expiration of the warranty period and make suitable arrangements for the performance of service. Customer shall be responsible for packaging and shipping the defective product to the service center designated by Tektronix, with shipping charges prepaid. Tektronix shall pay for the return of the product to Customer if the shipment is to a location within the country in which the Tektronix service center is located. Customer shall be responsible for paying all shipping charges, duties, taxes, and any other charges for products returned to any ot
This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadeq repair damage resulting from attempts by personnel other than Tektronix representatives to install, repair or service the product; b) to repair damage resulting from improper u se or connection to incompatible equipment; c) to repair any damage or malfunction caused by the use of non-Tektronix supplies; or d) to service a product that has been modied or integrated with other products when the effect of such modication or integration increases the time or difculty of servicing the product.
THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THE PRODUCT IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED. TEKTRONIX A ND ITS VENDORS DISCLAIM ANY
LIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
IMP TEKTRONIX’ RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY. TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.
btain service under this warranty, Customer must notify Tektronix of the defect before the
her locations.
uate maintenance and care. Tektronix shall not be obligated to furnish service under this warranty a) to
[W2 – 15AUG04]
Table of Contents
General Safety Summary ......................................................................................... iv
Preface ............................................................................................................. vii
Related Documents.......................................................................................... vii
Specications
Specications ................................ ................................ ................................ ..... 1-1
Performance Conditions .................................................................................... 1-1
Electrical Specications.......... .................................. ................................ ......... 1-2
Mechani
Environmental Characteristics ........................................................................... 1-11
Performance Verication Procedures
Performance Verication Procedures........................................................................... 2-1
Procedures .................................................................................................. 2-1
Brief
Diagnostics ................................................................................................... 2-1
Self Calibration ......................... ................................ ................................ ..... 2-3
Functional Test ............................................................................................... 2-3
Performance Tests ..... .................................. ................................ ......................... 2-8
Prerequisites....... .................................. ................................ ......................... 2-8
Req
Test Record ........................ .................................. ................................ ....... 2-10
10 MHz Reference Frequency Accuracy....................... ................................ ......... 2-19
Analog Offset Accuracy .................................................................................. 2-19
Analog Amplitude Accuracy . . ..... . ..... . .... . . .... . ..... . ..... . ... . . ..... . ..... . ... . . . .... . ..... . ..... . 2-23
Analog Harmonic Distortion ...................... ................................ ....................... 2-25
Analog Non-Harmonic Spurious Signal.............. .................................. ................. 2-27
Analog Phase Noise .... .................................. ................................ ................. 2-28
Marker High and Low Level Accuracy ........ ................................ ......................... 2-31
Marker Output Delay Accuracy.......................................................................... 2-33
DC Output Voltage Accuracy ............................................................................ 2-36
cal (Physical) Characteristics................................................................... 1-11
uired Equipment.............. ................................ .................................. ......... 2-8
AWG5000B Series Arbitrary Waveform Generators Technical Reference i
Table of Contents
List of Figure
Figure 2-1: Diagnostics dialog box...................... ................................ ....................... 2-2
Figure 2-2:
Figure 2-3: Equipment connections for checking the analog and marker outputs ... ..... . ..... . ... . . .... 2-4
Figure 2-4: Output waveform from the Analog, Mkr 1, and Mkr 2 outputs ............................... 2-5
Figure 2-5: Equipment connection for checking the digital data outputs .................................. 2-6
Figure 2-6: Output waveform from the Digital Data Out connector................... ..................... 2-7
Figure 2-7: Equipment connection for verifying the 10 MHz reference frequency accuracy... . ..... . 2-19
Figure 2-
Figure 2-9: Equipment connection for verifying the analog offset accuracy ..... ....................... 2-21
Figure 2-10: Equipment connections for verifying the analog harmonic distortion ............... ..... 2-25
Figure 2-11: Equipment connections for verifying the non-harmonic spurious signal .... . ..... . ... . . . 2-27
Figure 2-12: Equipment connections for verifying the analog phase noise........................... ... 2-29
Figure 2-13: Example of the analog phase noise measurement ........................................... 2-30
Figur
Figure 2-15: Equipment connections for verifying the marker output d elay accuracy .... . ..... . ..... . 2-34
Figure 2-16: Equipment connection for verifying the DC output voltage accuracy .. . ..... . .... . ..... . 2-36
Calibration dialog box ................ .................................. ........................... 2-3
8: Equipment connection for measuring the termination resistance .... ....................... 2-20
e 2-14: Equipment connection for verifying the marker high and low level accuracy .... . .... . . 2-31
s
ii AWG5000B Series Arbitrary Waveform Generators Technical Reference
List of Tables
Table 1-1: Run mode ............................ ................................ ................................ . 1-2
Table 1 -2: A
Table 1-3: Clock generator ................... .................................. ................................ . 1-3
Table 1-4: Trigger generator .................................................................................... 1-3
Table 1-5: Inter-channel skew control............... .................................. ......................... 1-3
Table 1-6: Waveform rotation control for analog output..................................................... 1-4
Table 1-7: Analog output ........................................................................................ 1-4
Table 1 -8
Table 1-9: Digital data output (option 03 only) .................. .................................. ........... 1-6
Table 1-10: Trigger and gate input ............................................................................. 1-7
Table 1-11: Event input .......................................................................................... 1-7
Table 1-12: Reference clock input......................... ................................ ..................... 1-8
Table 1-13: External clock input................................................................................ 1-8
Table
Table 1-15: DC output ...... ................................ .................................. ................... 1-8
Table 1-16: Oscillator output ..... ..... . ..... . ..... . ..... . ..... . .... . . .... . ..... . ..... . ..... . ..... . ..... . ... . . ... 1-9
Table 1-17: 10 MHz clock output .............................................................................. 1-9
Table 1-18: TekLink port ............. ................................ .................................. ......... 1-9
Table 1-19: CPU module and peripheral devices .... ................................ ......................... 1-9
ble 1-20: Display ........... ................................ .................................. ............... 1-10
Ta
Table 1-21: Power supply ..................................................................................... 1-10
Table 1-22: Mechanical characteristics ....... .................................. ............................. 1-11
Table 1-23: Environmental characteristics................................................................... 1-11
Table 2-1: Required equipment .......................... .................................. ..................... 2-9
Table 2-2: Test Waveforms ...................................................................................... 2-9
Table 2-3: Analog offset accuracy................................. ................................ ........... 2-21
Table 2-4: Analog amplitude accuracy ..... . .... . . .... . ..... . ..... . ... . . ..... . ..... . ... . . . .... . ..... . ..... . .. 2-23
Table 2-5: Analog harmonic distortion....................................................................... 2-26
Table 2-6: Analog non-harmonic spurious signal........................................................... 2-28
Table 2-7: Analog phase noise ................................................................................ 2-29
Table 2-8: Marker High and Low level accuracy.... ................................ ....................... 2-32
Table 2-9: DC output voltage accuracy ...................................................................... 2-36
rbitrary waveform ................................................................................. 1-2
: Marker output ........................................................................................ 1-6
1-14: Add input............................................................................................ 1-8
Table of Contents
AWG5000B Series Arbitrary Waveform Generators Technical Reference iii
General Safety Summary
General Safet
To Avoid Fi
re or Personal
Injury
ySummary
Review the fo this product or any products connected to it.
To avoid pot
Only qualied personnel should perform service procedures.
Use Proper Power Cord. Use only the power cord specied for this product and certied for the country of use.
Ground the Product. This product is grounded through the grounding conductor of the power cord. To avoid electric shock, the grounding conductor must be connected to earth ground. Before making connections to the input or output terminals of the product, ensure that the product is properly grounded.
Observe All Terminal Ratings. To avoid fire or shock haz ard, observe all ratings and markings on the product. Consult the product manual for further ratings information before making connections to the product.
Power Disconnect. The power cord disconnects the product from the power source. Donotblockthepowercord;itmustremain accessible to the user at all times.
llowing safety precautions to avoid injury and prevent damage to
ential hazards, use this product only as specied.
Do Not Operate Without Covers. Do not operate this product with covers or panels removed.
Do Not Operate With Suspected Failures. If you suspect that there is damage to this product, have it inspected by qualied service personnel.
Avoid Exposed Circuitry. Do not touch exposed connections and components when powe r is present.
Do Not Operate in Wet/Damp Conditions.
Do Not Operate in an Explosive Atmosphere.
eep Product Surfaces Clean and Dry.
K
Provide Proper Ventilation. Refer to the manual’s installation instructions for
details on installing the product so it has proper ventilation.
iv AWG5000B Series Arbitrary Waveform Generators Technical Reference
General Safety Summary
Terms in this Manual
Symbols and Terms on the
Product
These terms may
WAR NI NG . Warning statements identify conditions or practices that could result
in injury or loss of life.
CAUTION. Caution statements identify conditions or practices that could result in
damage to this product or other property.
These terms may appear on the product:
DANGER in the marking.
WARNING read the marking.
CAUTIO
The following symbol(s) may appear on the product:
appear in this manual:
dicates an injury hazard immediately accessible as you read
indicates an injury hazard not immediately accessible as you
N indicates a hazard to property including the product.
AWG5000B Series Arbitrary Waveform Generators Technical Reference v
General Safety Summary
vi AWG5000B Series Arbitrary Waveform Generators Technical Reference
Preface
Related Documents
This manual contains specications and performance verication procedures for the AWG5000B Series Arbitrary Waveform Generators.
The following user documents are also available for this product:
AWG5000B and AWG7000B Series Arbitrary Waveform Generators Quick Start User Manual. This document describes the functions and use of the
instrume
AWG5000B Series Arbitrary Waveform Generators Service Manual.Thisisa PDF only m
nt.
anual that provides module-level service information.
AWG5000B Series Arbitrary Waveform Generators Technical Reference vii
Preface
viii AWG5000B Series Arbitrary Waveform Generators Technical Reference
Specications
Specications
This section contains the specications for the instruments.
All specications are guaranteed unless noted as "typical". Typical specications are provided for your convenience but are not guaranteed. Specications that are marked with the
Performance Conditions
To meet specications, following conditions must be met:
symbol are checked in this manual.
The instrument must have been calibrated/adjusted at an ambient temperature between +20 °C and +30 °C.
The instrument must be operating within the environmental limits. (See Table1-23onpage1-11.)
The instrument must be powered from a source that me ets the specications. (SeeTable1-21onpage1-10.)
The instrument must have been operating continuously for at least 20 minutes within the specified operating temperature range.
AWG5000B Series A rbitrary Waveform Generators Technical Reference 1–1
Specications
Electrical Sp
ecications
Table 1-1: Run mode
Characteris
Continuous m
Triggered mode
Gated mode An arbitrary waveform is output only when a gate signal is asserted. The waveform output
Sequence
tics
ode
mode
Description
An arbitrary
An arbitrar is output, the instrument waits for the next trigger signal.
is repeated while the gate signal stays asserted. When the gate signal is deasserted, the waveform o
Standard Option 08: Fast sequence switching
waveform is output continuously.
y waveform is output only once when a trigger signal is applied. After the waveform
utput stops immediately.
: Sequence switching with wait trigger
Table 1-2: Arbitrary waveform
Characteristics Description
Waveform length
Without Option 01
With Option 01
Hardware limitation 250 points minimum
Waveform granularity
DAC resolution
Number of waveforms Up to 32,000 waveforms (pre-dened waveforms are not included.)
Sequence length
Sequence controls Standard: Repeat count, Wait-for-Trigger (ON only), Go-to-N, and Jump are available.
Repeat count
Jump timing
Sequence switching time, typical
AWG5012B and AWG5014B
AWG5002B and AWG5004B
AWG5012B Option 08 and AWG5014B Option 08
AWG5002B Option 08 and AWG5004B Option 08
1 to 16,200,000 points
1 to 32,400,000 points
1 point
14 bits
1 to 8,000 steps
Option 08: Repeat count, Wait-for-Trigger (ON or OFF), Go-to-N, and Jump are available.
1 to 65,536 or innite (all channels operate the same sequence)
Synchronous or Asynchronous selectable
400 ns
800 ns
5.4 ns
8.3 ns
1–2 AWG5000B Series Arbitrary Waveform Generators Technical Reference
Specications
Table 1-3: Cloc
k generator
Characteristics Description
Sampling rate control
Range
AWG5012B and
10.0000 MS/s to 1.2000 GS/s
AWG5014B
AWG5002B an
d
10.0000 MS/
s to 600.000 MS/s
AWG5004B
Resolutio
Internal clock frequency
Internal clock frequency accuracy,
n
8digits
Within ± (1
ppm + aging)
Aging: within ± 1 ppm/year
typical
Reference oscillator accuracy
Reference oscillator accuracy,
Within ± (1 ppm + aging)
Aging: within ± 1 ppm/year
typical
Table 1-4: Trigger generator
Characteristics Description
Trigger rate
Range 1.0 μsto10.0s
Resolution 3 digits and 0.1 μs m inim um
Accuracy
Same as the reference oscillator
Table 1-5: Inter-channel skew control
Characteristics Description
Skew control
sto+5ns
Range
solution
Re
ew accuracy, typical
Sk
1
Effective skew setting is the absolute value of the difference between the skew setting on channels.
1
–5 n
5ps
10% of effective skew setting +150 ps)
±(
AWG5000B Series A rbitrary Waveform Generators Technical Reference 1–3
Specications
Table 1-6: Wave
Characteristics Description
Phase control
Range
Resolution
Time control
Range
Resolution 1 ps
Point cont
rol
Range
Resolution 0.001 points
form rotation control for analog output
–180° to +180
0.1° of wave
–1/2 period to +1/2 period of waveform
–50% to +5
° of w aveform
form
0% of waveform
Table 1-7: Analog output
Characteristics Description
Connector type BNC at front panel
Type of output (+) and (–) complementary output
Output impedance 50
Amplitude controls
Range
Normal mode 20 mV to 4.5 V peak-peak
Direct D/A mode
Resolution 1 mV
Offset controls
Range
Normal mode –2.25 V to +2.25 V
Direct D/A mode N/A
Resolution 1 mV
Amplitude accuracy
Offset accuracy
Bandwidth, typical
Normal mode
Direct D/A mode 370 MHz (at –3 dB), when amplitude=0.6 V p-p
Rise/fall tim e , typical
Normal mode
Direct D/A mode 0.95 ns (10% to 90%), when amplitude=0.6 Vp-p
Overshoot, typical < 10% , when amplitude=2.0 Vp-p
20 mV to 0.6 V peak-peak
DC accuracy: within ± (2% of amplitude + 2 mV) at offset=0V
DC accuracy: within ± (2% of |offset| + 15 mV) at minimum amplitude
250 MHz (at –3 dB), when amplitude=2.0 Vp-p, offset=0 V
1.4 ns (10% to 90%), when amplitude=2.0 Vp-p, offset=0 V
1–4 AWG5000B Series Arbitrary Waveform Generators Technical Reference
Specications
Table 1-7: Analog output (cont.)
Characteristics Description
Ringing, typical
Normal mode
Direct D/A mode
Low pass lter
Normal mode
Direct D/A mode N/A
Delay from marker, typical
Skew between (+) and (–) outputs, typical
ON/OFF control Output relay is available for each channel. A control is common to the complementary output.
Harmonic distortion
AWG501xB Normal mode < –40 dBc, when amplitude=2.0 Vp-p, offset=0 V, clock=1.2 GS/s, signal=37.5 MHz
AWG501xB Direct D/A mode < –49 dBc, when amplitude=0.6 Vp-p, clock=1.2 GS/s, signal=37.5 MHz
AWG500xB Normal mode < –46 dBc, when amplitude=2.0 Vp-p, offset=0 V, clock=600 MS/s, signal=18.75 MHz
AWG500xB Direct D/A mode < –55 dBc, when amplitude=0.6 V p-p, clock=600 MS/s, signal=18.75 MHz
Non harmonic spurious
AWG5012B and AWG5014B < –60 dBc, DC to 600 MHz, when clock=1.2 GS/s, signal=37.5 MHz
AWG5002B and AWG5004B < –60 dBc, D C to 300 MHz, when clock=600 MS/s, signal=18.75 MHz
SFDR, typical
AWG501xB 50 dBc, when clock=1.2 GS/s, signal=37.5 MHz (normal output mode, amplitude=2.0 Vp-p,
AWG501xB and AWG500xB 56 dBc, when clock=600 MS/s, signal=18.75 MHz (normal output mode, amplitude=2.0 Vp-p,
Normal mode Amplitude =
1.0 Vp-p
Direct D/A mode Amplitude =
0.6 Vp-p
Phase noise
AWG5012B and AWG5014B < –85 dBc/Hz at 10 kHz offset, when clock=1.2 GS/s, signal=37.5 MHz
AWG5002B and AWG5004B < –85 dBc/Hz at 10 kHz offset, when clock=600 MS/s, signal=18.75 MHz
750 mVp-p, when amplitude=4.5 Vp-p, lter= through 80 mVp-p, when amplitude=2.0 Vp-p, lter= through
60 mVp-p, when amplitude=0.6 Vp-p
20 MHz, 100 MHz, Through (Bessel type)
Direct output delay +19.0 ns: low pass=20 MHz
Direct output delay +5.3 ns: low pass=100 MHz
Direct output delay +1.5 ns: low pass=Through
–1.5 ns to +0.4 ns: direct D/A mode
(when amplitude=0.6 Vp-p, offset=0 V)
< 200 ps
Measured with 32-point sine waveform, dened up to 5th harmonics.
Amplitude=2.0 Vp-p, offset=0 V, measured with 32-point sine waveform.
offset=0 V, measured with 32-point sine waveform.)
offset=0 V, measured with 32-point sine waveform.)
–60 dBc, w hen signal=10 MHz
–80 dB c, when signal=1 MHz
(clock=600 MS/s, offset =0 V, m easured with 60 and 600 points/cycle sine waveform, DC to 300 MHz.)
–64 dBc, w hen signal=10 MHz
–80 dB c, when signal=1 MHz
(clock=600 MS/s, offset =0 V, m easured with 60 and 600 points/cycle sine waveform, DC to 300 MHz.)
Amplitude=2.0 Vp-p, offset=0 V, measured with 32-point sine waveform.
AWG5000B Series A rbitrary Waveform Generators Technical Reference 1–5
Specications
Table 1-8: Mark
Characteristics Description
Connector type BNC
Number of outputs Marker 1 and Marker 2 are available for each channel.
Type of output Single-ended output
Output impedance 50
Level cont
Voltage window
Amplitude 0.1 Vp-p to 3.7 Vp-p
Resolution 0.01 V
Level accuracy
Output current
Variable delay control
Range 0 to 1000 ps
Resolution 50 ps
Var iab
fall time, typical
Rise/
Random jitter on clock pattern,
al
typic
Total jitter on random pattern,
cal
typi
er output
rols
le delay accuracy
–1.0 V to +2
DC accuracy: ± (10% of |setting| + 120 mV) into 50
± 54 mA maximum
Available for Marker 1 and Marker 2
± (5% of |setting| + 250 ps)
300 ps
5psrm
150 p
.7 V into 50
(20% to 80% of swing), when Hi= 1.0 V, Low=0V
s (by 0101... clock pattern), when Hi= 1.0 V, Low=0V
s p-p (by PN15 pattern, when Hi= 1.0 V, Low=0V)
Table 1-9: Digital data output (option 03 only)
Characteristics Description
Connector type SMB
Number of outputs 28 (14-bit output on channel 1 and channel 2)
Output impedance 50
Level controls
Voltage range
Amplitude 0.1 Vp-p minimum
Resolution 0.01 V
Level accuracy, typical
Output current
Rise/fall time, typical 300 ps (20% to 80%, when Hi= 1.0 V, Low=0V)
Delay from maker, typical
ON/OFF control A common ON/OFF control is available for 14-bit output
Skew between outputs, typical
–1.0 V to +2.7 V into 50
DC accuracy: ± (10% of |setting| + 120 mV) into 50
± 54 mA maximum
–41 ns to –82 ns, when Hi= 1.0 V, Low=0V
< 400 ps between 14-bit outputs
1–6 AWG5000B Series Arbitrary Waveform Generators Technical Reference
Specications
Table 1-10: Tri
Characteristics Description
Connector type BNC
Input impeda
Polarity Positive or
Input voltage range
When1kΩ selected
When 50 selected
Threshold control
Level –5.0 V to 5
Resolution 0.1 V
Accuracy, typical
Input voltage swing 0.5 Vp-p minimum
m pulse width
Minimu
Triggered mode 20 ns
Gated mode 1024 * sampling period + 10 ns
Trigger delay to analog output, typical
Trigger hold off time, typical 160 * sampling period - 200 ns
Gate delay to analog output, typical 240 * sampling period + 500 ns
Trigger jitter, typical 2.0 ns to 4.5 ns
gger and gate input
nce
1kΩ or 50 Ω selectable
negative selectable
–10Vto10V
<5Vrms
.0 V
± (5% of |setting| + 0.1 V)
48 * sampling period + 500 ns
Table 1-11: Event input
Characteristics Description
Connector type BNC
Input impedance
Polarity Positive or negative selectable
Input voltage range
When1kΩ selected
When 50 selected
Threshold control
Level –5.0 V to 5.0 V
Resolution 0.1 V
Accuracy, typical
Input voltage swing 0.5 Vp-p minimum
Minimum pulse width 20 ns
Delay to analog output, typical
Hold off time, typical 260 * sampling period + 300 ns
1kΩ or 50 Ω selectable
–10Vto10V
<5Vrms
± (5% of |setting| + 0.1 V)
200 * sampling period + 500 ns
AWG5000B Series A rbitrary Waveform Generators Technical Reference 1–7
Specications
Table 1-12: Ref
Characteristics Description
Connector type BNC
Input impeda
Input volta
Fixed mode i
Variable m range
Variable m
AWG5012B
AWG5002
erence clock input
nce
ge swing
nput frequency
ode input frequency
ode multiplier rate
and AWG5014B
B and AWG5004B
50 (AC coupled)
0.2 Vp-p to 3
10 MHz, 20 MH
5 MHz to 600 MHz Acceptabl
1to240
1to120
Vp-p
z, and 100 MHz within ± 0.5%
e frequency drift while the instrument is operating: ± 0.5%
Table 1-13: External clock input
Characteristics Description
Connector type BNC
Input impedance
Frequency range 600 MHz to 1200 MHz
Input voltage swing 0.2 V to 0.8 Vp-p
Divider
AWG5012B and AWG5014B 1/1, 1/2, 1/4, 1/8, ... ,1/32
AWG5002B and AWG5004B 1/2, 1/4, 1/8, ... ,1/32
50 (AC coupled)
Table 1-14: Add input
Characteristics Description
Connector type BNC on the rear panel, for each channel
Input impedance
DC gain, typical
Bandwidth, typical
Input voltage range ± 1.0 V
Maximum input voltage ± 5.0 V
50 (DC coupled)
1
DC to 100 MHz, at –3 dB, when amplitude is 1 Vp-p
Table 1-15: DC output
Characteristics Description
Connector type 2 x 4 pin header, 2.54 mm pitch (female)
Number of outputs
Output voltage control
Range –3.0 V to +5.0 V
Resolution 10 mV
Control Independent for each output
4
1–8 AWG5000B Series Arbitrary Waveform Generators Technical Reference
Table 1-15: DC output (cont.)
Characteristics Description
Output volta
Output curr
Output imp
ge accuracy
ent
edance, typical
± (3% of |setting| + 120 mV) into High-Z load
±100 mA maximum
1
Table 1-16: Oscillator output
Characteristics Description
Connector type BNC
Output impedance 50 (AC coupled)
Output frequency range
Output voltage swing, typical 0.4 Vp-p into 50
600 MHz to 1200 MHz
Table 1-17: 10 MHz clock output
Characteristics Description
Connector type BNC
Output impedance 50 (AC coupled)
Amplitude, typical
1.2 Vp-p into 50
2.4 Vp-p into 1 M
Specications
Table 1-18: TekLink port
Characteristics Description
Connector type
40 pins
Table 1-19: CPU module and peripheral devices
Characteristics Description
CPU Celeron D processor
Memory
Hard disk drive
Optical disk drive CD-RW/DVD drive
USB 2.0 6 (2 x front, 4 x rear)
LAN
Video output D-sub, 15 pins
GPIB IEEE 488.2 standard interface, 24 pins
Keyboard
Mouse
Serial port RS-232C, D -sub, 9 pins
Parallel port D-sub, 25 pins
2 GB DDR2-SDRAM
More than 80 GB
1000/100/10 BASE-T
PS-2 compatible, mini-DIN, 6 pins
PS-2 compatible, mini-DIN, 6 pins
AWG5000B Series A rbitrary Waveform Generators Technical Reference 1–9
Specications
Table 1-20: Dis
Characteristics Description
Size
Resolution 1024 X 768 pix
Touch screen Built-in touch screen
play
210 mm X 158 mm
els
Table 1-21: Power supply
Characteristics Description
Source voltage and frequency
Rating voltage
Frequency range 47 Hz to 63 Hz
Power consumption 560 W
Surge current 30 A peak (25 °C) for 5 line cycles, after product has been turned off for at least 30 s.
10 0 VA C to 2 40 VAC
1–10 AWG5000B Series Arbitrary Waveform Generators Technical Reference
Specications
Mechanical (P
hysical) Characteristics
Table 1-22: Mechanical characteristics
Characteris
Net w eight
Dimensions
Environ
tics
Without package
With package
Height
Width
Length
mental Characteristics
Description
Approximately 19.5 kg (43.0 lb)
Approximately 28.5 kg (62.8 lb)
245 mm (9.6 in)
465 mm (18.3 in)
500 mm (19.7 in)
Table 1-23: Environmental characteristics
teristics
Charac
Temperature
Operating +10 °C to +40 °C
Non-operating
Relative humidity
Operating 5% to 80% (no condensation)
Non-operating
Altitude
Operating Up to 3,000 m (approximately 10,000 feet)
Non-operating
Clearance
Top and bottom
Side 15 cm (5.9 in)
Rear
ption
Descri
–20 °C to +60 °C
Maximum wet-bulb temperature 29 °C
5% to 90% (no condensation)
ximum wet-bulb temperature 29 °C
Ma
aximum operating temperature decreases 1 °C each 300 m above 1.5 km
M
p to 12,000 m (approximately 40,000 feet)
U
2cm(0.8in)
7.5 cm (3.0 in)
AWG5000B Series A rbitrary Waveform Generators Technical Reference 1–11
Specications
1–12 AWG5000B Series Arbitrary Waveform Generators Technical Reference
Performance Verication Procedures
Performance Verication Procedures
Two types of performance verication procedures can be performed on the instrument: Brief Procedures and Performance Tests. You may not need to perform all o
To rapidly conrm that the instrument functions and was adjusted properly, perform Diagnostics and Self Calibration.
Advantages: These procedures are quick to do and require no external equipment or signal sources. These procedures perform extensive functional and accuracy testing to provide high condence that the instrument will perform properly.
f these procedures, depending on what you want to accomplish.
Brief Procedures
To further check functionality, rst perform Diagnostics and Self Calibr and then perform Functional Test.
Advantages: The procedure requires minimal additional time to perform, and requires minimal equipment. The procedure can be used when the instrument is rst rec eived.
If more extensive conrmation of performance is desired, complete the self tests and functional test, and then do the Performance Tests.
Advantages: These procedures add direct checking of warranted specications. These procedures require specic test equipment. (See page 2-8, Required Equipment.)
If you are not familiar w ith operating this instrument, refer to the online h elp or the user information supplied with the instrument.
There are three procedures in this section that provide a quick way to conrm basic functionality and proper adjustment:
Diagnostics
ation,
Self Calibration
Functional Test
Diagnostics
The following steps run the internal routines that conrm basic functionality and proper adjustment.
Equipment Prerequisites
None None
AWG5000B Series A rbitrary Waveform Generators Technical Reference 2–1
Brief Procedures
1. Disconnect all
2. Select System > Diagnostics....
Figure 2-1: Diagnostics dialog box
the cables from the output channels.
3. In the Diagnostics dialog box, conrm that all the check boxes are selected. If they ar
4. Click the Execute button to execute the diagnostics.
The internal diagnostics perform an exhaustive verication of proper instrument function. This verication may take several minutes. When the veri
5. Verify that Pass appears as Status in the dialog box when the diagnostics com
6. Click the Close button.
e not all selected, click the Select All button.
cation is completed, the resulting status will appear in the dialog box.
plete.
2–2 AWG5000B Series Arbitrary Waveform Generators Technical Reference
Brief Procedures
Self Calibrat
ion
Equipment Prerequisites
None Power on the instrument and allow a
20 minute warm-up before doing this procedure.
1. Select System > Calibration....
Figure 2-2: Calibration dialog box
2. Click the Execute button to start the routine.
3. Verify that Pass appears in the status column for all items when the calibration
completes.
4. Click the Close button.
Functional Test
Checking the Analog and
Marker Outputs
The purpose of the procedure is to conrm that the instrument functions properly. The required equipment is three 50 BNC cables, an oscilloscope, and a 50 SMB-BNC cable (Option 03 only).
Required equipment Prerequisites
Oscilloscope (DPO7054 or equivalent)
Three 50 BNC cables
1. Press the All Outputs On/Off button on the AWG5000B to turn off all the outputs.
2. Use a 50 BNC cable to connect the Channel 1 Analog connector on the AWG5000B to the CH1 connector on the oscilloscope.
3. Use a 50 BNC cable to connect the Channel 1 Mkr 1 connector on the AWG5000B to the CH2 connector on the oscilloscope.
4. Use the 50 BNC cable to connect the Channel 1 Mkr 2 connector on the AWG5000B to the CH3 connector on the oscilloscope.
None
AWG5000B Series A rbitrary Waveform Generators Technical Reference 2–3
Brief Procedures
Figure 2-3: Equipment connections for checking the analog and marker outputs
5. Set the oscilloscope as follows:
a. Vertical scale: 1 V/div (CH1, CH2, and CH3)
b. Horizo
c. Input coupling: DC
d. Input impedance: 50
e. CH 1 position: +2 div (if necessary)
f. CH 2 position: –1 div (if necessary)
g. CH 3 position: –3 div (if necessary)
h. Tri
i. Trigger level: 0 mV
j. Trigger slope: Positive
k. Trigger mode: Auto
6. Press the Factory Default button on the AWG5000B.
7. Press the Ch1 Select button on the AWG5000B.
n the AWG5000B, load the sine_mk1_mk2 waveform as an output
8.O
waveform.
ntal scale: 200 ns/div
gger source: CH1
a. Select File > Open File....
2–4 AWG5000B Series Arbitrary Waveform Generators Technical Reference
Brief Procedures
b. In the dialog bo
Files\Tektronix\AWG\System\PV directory, and then select the pv_awg5000.awg le. The Waveform List window appears.
c. In the window, select (drag and drop) the sine_mk1_mk2 waveform on
the User Defined tab.
NOTE. If your instrument is an AWG5002B or AWG5004B, a warning message
is displayed when you open the pv_awg5000.awg le. Ignore the message and press the OK button.
9. Press the Ch 1 On button on the AWG5000B to enable the channel 1 output.
10. Press the Run button on the AWG5000B to output the waveform.
11. Check that the Channel 1 Analog, Mkr 1, and Mkr 2 waveforms are properly
displayed on the oscilloscope screen.
x, navigate to the C:\Program
Figure 2-4: Output waveform from the Analog, Mkr 1, and Mkr 2 outputs
12. Press the Ch 1 On button again to disable the channel 1 output.
13. Repeat the test for the Channel 2 Analog, Mkr 1, and Mkr 2 outputs.
14. For the AWG5014B or AWG5004B: Repeat the test for the Channel 3 and
Channel 4 Analog, Mkr 1, and Mkr 2 outputs.
AWG5000B Series A rbitrary Waveform Generators Technical Reference 2–5
Brief Procedures
Checking the D
igital Data
Outputs (Option 03 Only)
Required equipment Prerequisites
Oscilloscope (DPO7054 or equivalent)
50 BNC cable
50 SMB-BNC cable (Tektronix part number 174-5104-00)
1. Pres
stheAll Outputs On/Off button on the AWG5000B to turn off all the
None
outputs.
2. Use the 50 SMB-BNC cable and 50 BNC cable to connect the Ch 1 Digital Data Out 0 connector on the AWG5000B rear panel to the CH1 connector on the oscilloscope.
Figure 2-5: Equipment connection for checking the digital data outputs
3. Set the oscilloscope as follows:
a. Vertical scale: 500 mV/div
b. Horizontal sc ale: 200 ns/div
c. Input coupling: DC
d. Input impedance: 50
e. Trigger source: CH1
f. Trigger level: 500 mV
g. Trigger slope: Positive
h. Trigger mode: Auto
4. Press the Factory Default button on the AWG5000B.
5. Press the Ch1 Select button on the AWG5000B.
2–6 AWG5000B Series Arbitrary Waveform Generators Technical Reference
Brief Procedures
6. On the AWG5000B
a. Select File > Open File....
b. In the dialog box, navigate to the C:\Program
Files\Tektronix\AWG\System\PV directory, and then select the pv_awg5
c. In the window, select (drag and drop) the square1 waveform on the User
Dened tab.
7. Press the Ch 1 On button on the AWG5000B to enable the channel 1 output.
8. Press the Run button on the AWG5000B to output the waveform.
9. Check that the square wave is properly displayed on the oscilloscope screen.
(See Figure 2-6.)
NOTE. If your instrument has rmware version 2.0 or earlier, the amplitude of the
yed waveform is different from the waveform shown in the following gure.
displa
, load the square1 waveform as an output waveform.
000.awg le. The Waveform List window appears.
Figure 2-6: Output waveform from the Digital Data Out connector
10. Move the SMB-BNC cable from the Ch 1 Digital Data Out 0 connector to the Ch 1 Digital Data Out 1 connector and repeat the previous step.
11. Repeat step 10 for the remaining digital data outputs (Ch 1 Digital Data Out 2 to Ch 1 Digital Data Out 13).
12. Press the Ch 1 On button again to disable the channel 1 output.
13. Repeat the test for all the Ch 2 Digital Data outputs.
AWG5000B Series A rbitrary Waveform Generators Technical Reference 2–7
Performance Tests
Performance T
Prerequisites
Required Equipment
ests
This section marked with the
The tests in this section comprise an extensive, valid conrmation of performance and functionality when the following requirements are met:
The cabinet must be installed on the instrument.
You must h Calibration, and the procedure Functional Tests.
The inst between +20 °C and +30 °C, must have been operating for a warm-up period of at least 20 minutes, and must be operating at an ambient temperatures between +10 °C and +40 °C.
contains performance verication procedures for the specications
symbol.
ave performed and passed the procedure Diagnostics and Self
rument must have been last adjusted at an ambient temperature
The following table lists the test equipment required to perform all of the performance verication procedure. The table identies examples of recommended equipment and lists the required precision where applicable. If
ubstitute other test equipment for the listed examples, the equipment must
you s meet or exceed the listed tolerances.
2–8 AWG5000B Series Arbitrary Waveform Generators Technical Reference
Performance Tests
Table 2-1: Requ
Item Qty. Minimum requirements Recommended equipment
Oscilloscope
Frequency co
Sampling os
Spectrum analyzer
Digital mu
50 BNC cable
50 BNC termination
BNC-SMA adapter
BNC-N adapter
BNC-dual banana adapter
DC output lead set
ltimeter
ired equipment
unter
cilloscope
Test Waveforms
1 ea. Bandwidth: 50
4 channels
1 ea. Frequency ac
1 ea.
1 ea.
1 ea.
2 ea.
1 ea.
2 ea.
1 ea.
1 ea.
1 ea. 8-pin twisted pair, 24 inch Tektronix part number 012-1697-00
Bandwidth: 2 channels
Bandwidth: DC to 8 GHz Tektronix RSA3308A
DC accuracy: within ± 0.01%
DCto2GHz
DC to 1 GHz, feedthrough
BNC female to SMA male connectors
BNC female to N male connectors
BNC to dual banana plugs
0 MHz or higher
curacy: within ± 0.01 ppm
20 GHz or higher
Tektronix DPO7054
Agilent Tech
Tektronix C
Keithley 2 or Agilent Technologies 34410A
Tektronix part number 012-0057-01
Tektronix part number 011-0049-02
Tektronix part number 015-0554-00
Tektronix part number 103-0045-00
Tektronix part number 103-0090-00
(supplied with the AWG5000B)
nologies 53181A
SA8200 with 80E03
000 DMM
The following table lists the test waveforms that are used for the performance verication procedures and functional test. These are included in the
wg5000.awg le on the C: drive.
pv_a
Table 2-2: Test Waveforms
No. Waveform name Purpose
1 dc_minus For checking the analog amplitude accuracy
2 dc_plus For checking the analog amplitude accuracy
3dc_zero
4 marker_hi For checking the marker high level accuracy
5
6 sine32 For checking analog harmonic distortion, analog
7
8 square1 For checking the marker output delay accuracy test
marker_low For checking the marker low level accuracy
sine_mk1_mk2
For checking the analog offset accuracy
non-harmonic spurious signal, and analog phase noise
For the functional test
NOTE. If your instrument is an AWG5002B or AWG5004B, a warning message
is displayed when you open the pv_awg5000.awg le. Ignore the message and press the OK button.
AWG5000B Series A rbitrary Waveform Generators Technical Reference 2–9
Performance Tests
Test Record
Photocopy this page and the next eight pages, and use them to record the performance test results for your instrument.
AWG5000B performance test record
Instrument Model:
Instrument Serial Number: Certicate Number:
Temperature:
Date of Calibration:
Performance Test
10 MHz Reference Frequency Accuracy
Analog Offset Accuracy
Ch 1
/Ch 1
Ch 2
Offset Output mode
+2.25 V
+1 V
0.0 V
–1 V
–2.25 V
N/A (0V) Direct D/A out: On
Offset Output mode
+2.25 V
+1 V
0.0 V
–1 V
–2.25 V
N/A (0V) Direct D/A out: On
Offset Output mode
+2.25 V
+1 V
0.0 V
–1 V
–2.25 V
N/A (0V) Direct D/A out: On
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
RH %:
Technician:
Minimum Incoming
9.99998 MHz 10.00002 MHz
2190 mV 2310 mV
965 mV 1035 mV
–15 mV +15 mV
–1035 mV –965 mV
–2310 mV –2190 mV
–15 mV +15 mV
2190 mV 2310 mV
965 mV 1035 mV
–15 mV +15 mV
–1035 mV –965 mV
–2310 mV –2190 mV
–15 mV +15 mV
2190 mV 2310 mV
965 mV 1035 mV
–15 mV +15 mV
–1035 mV –965 mV
–2310 mV –2190 mV
–15 mV +15 mV
Outgoing
Maximum
2–10 AWG5000B Series Arbitrary Waveform Generators Technical Reference
AWG5000B performance test record (cont.)
Performance Tests
Performance Test
/Ch 2
Ch 3
/Ch 3
Ch 4
/Ch 4
Offset Output mode
+2.25 V
+1 V
0.0 V
–1 V
–2.25 V
N/A (0V) Direct D/A out: On
Offset Output mode
+2.25 V
+1 V
0.0 V
–1 V
–2.25 V
N/A (0V) Direct D/A out: On
Offset Output mode
+2.25 V
+1 V
0.0 V
–1 V
–2.25 V
N/A (0V) Direct D/A out: On
Offset Output mode
+2.25 V
+1 V
0.0 V
–1 V
–2.25 V
N/A (0V) Direct D/A out: On
Offset Output mode
+2.25 V
+1 V
0.0 V
–1 V
–2.25 V
N/A (0V) Direct D/A out: On
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Minimum Incoming
2190 mV 2310 mV
965 mV 1035 mV
–15 mV +15 mV
–1035 mV –965 mV
–2310 mV –2190 mV
–15 mV +15 mV
2190 mV 2310 mV
965 mV 1035 mV
–15 mV +15 mV
–1035 mV –965 mV
–2310 mV –2190 mV
–15 mV +15 mV
2190 mV 2310 mV
965 mV 1035 mV
–15 mV +15 mV
–1035 mV –965 mV
–2310 mV –2190 mV
–15 mV +15 mV
2190 mV 2310 mV
965 mV 1035 mV
–15 mV +15 mV
–1035 mV –965 mV
–2310 mV –2190 mV
–15 mV +15 mV
2190 mV 2310 mV
965 mV 1035 mV
–15 mV +15 mV
–1035 mV –965 mV
–2310 mV –2190 mV
–15 mV +15 mV
Outgoing
Maximum
AWG5000B Series A rbitrary Waveform Generators Technical Reference 2–11
Performance Tests
AWG5000B performance test record (cont.)
Performance Test
Analog Amplitude Accuracy
Ch1
/Ch1
Ch2
Amplitude
20 mVp-p
200 mVp-p
500 mVp-p
1.0 Vp-p
2.0 Vp-p
4.5 Vp-p
20 mVp-p
200 mVp-p
600 mVp-p
Amplitude
20 mVp-p
200 mVp-p
500 mVp-p
1.0 Vp-p
2.0 Vp-p
4.5 Vp-p
20 mVp-p
200 mVp-p
600 mVp-p
Amplitude
20 mVp-p
200 mVp-p
500 mVp-p
1.0 Vp-p
2.0 Vp-p
4.5 Vp-p
20 mVp-p
200 mVp-p
600 mVp-p
Output mode
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A/out: Off
Direct D/A/out: Off
Direct D/A/out: Off
Direct D/A out: On
Direct D/A out: On
Direct D/A out: On
Output mode
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A/out: Off
Direct D/A/out: Off
Direct D/A/out: Off
Direct D/A out: On
Direct D/A out: On
Direct D/A out: On
Output mode
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A/out: Off
Direct D/A/out: Off
Direct D/A/out: Off
Direct D/A out: On
Direct D/A out: On
Direct D/A out: On
Minimum Incoming
17.6 mV 22.4 mV
194 mV 206 mV
488 mV 512 mV
0.978 V 1.022 V
1.958 V 2.042 V
4.408 V 4.592 V
17.6 mV 22.4 mV
194 mV 206 mV
586 mV 614 mV
17.6 mV 22.4 mV
194 mV 206 mV
488 mV 512 mV
0.978 V 1.022 V
1.958 V 2.042 V
4.408 V 4.592 V
17.6 mV 22.4 mV
194 mV 206 mV
586 mV 614 mV
17.6 mV 22.4 mV
194 mV 206 mV
488 mV 512 mV
0.978 V 1.022 V
1.958 V 2.042 V
4.408 V 4.592 V
17.6 mV 22.4 mV
194 mV 206 mV
586 mV 614 mV
Outgoing
Maximum
2–12 AWG5000B Series Arbitrary Waveform Generators Technical Reference
AWG5000B performance test record (cont.)
Performance Tests
Performance Test
/Ch2
Ch3
/Ch3
Amplitude
20 mVp-p
200 mVp-p
500 mVp-p
1.0 Vp-p
2.0 Vp-p
4.5 Vp-p
20 mVp-p
200 mVp-p
600 mVp-p
Amplitude
20 mVp-p
200 mVp-p
500 mVp-p
1.0 Vp-p
2.0 Vp-p
4.5 Vp-p
20 mVp-p
200 mVp-p
600 mVp-p
Amplitude
20 mVp-p
200 mVp-p
500 mVp-p
1.0 Vp-p
2.0 Vp-p
4.5 Vp-p
20 mVp-p
200 mVp-p
600 mVp-p
Output mode
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A/out: Off
Direct D/A/out: Off
Direct D/A/out: Off
Direct D/A out: On
Direct D/A out: On
Direct D/A out: On
Output mode
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A/out: Off
Direct D/A/out: Off
Direct D/A/out: Off
Direct D/A out: On
Direct D/A out: On
Direct D/A out: On
Output mode
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A/out: Off
Direct D/A/out: Off
Direct D/A/out: Off
Direct D/A out: On
Direct D/A out: On
Direct D/A out: On
Minimum Incoming
17.6 mV 22.4 mV
194 mV 206 mV
488 mV 512 mV
0.978 V 1.022 V
1.958 V 2.042 V
4.408 V 4.592 V
17.6 mV 22.4 mV
194 mV 206 mV
586 mV 614 mV
17.6 mV 22.4 mV
194 mV 206 mV
488 mV 512 mV
0.978 V 1.022 V
1.958 V 2.042 V
4.408 V 4.592 V
17.6 mV 22.4 mV
194 mV 206 mV
586 mV 614 mV
17.6 mV 22.4 mV
194 mV 206 mV
488 mV 512 mV
0.978 V 1.022 V
1.958 V 2.042 V
4.408 V 4.592 V
17.6 mV 22.4 mV
194 mV 206 mV
586 mV 614 mV
Outgoing
Maximum
AWG5000B Series Arbitrary Waveform Generators Technical Reference 2–13
Performance Tests
AWG5000B performance test record (cont.)
Performance Test
Ch4
/Ch4
Analog Harmonic Distortion (AWG501xB)
Ch 1
Ch 2
Ch 3
Ch 4
Amplitude
20 mVp-p
200 mVp-p
500 mVp-p
1.0 Vp-p
2.0 Vp-p
4.5 Vp-p
20 mVp-p
200 mVp-p
600 mVp-p
Amplitude
20 mVp-p
200 mVp-p
500 mVp-p
1.0 Vp-p
2.0 Vp-p
4.5 Vp-p
20 mVp-p
200 mVp-p
600 mVp-p
Amplitude
2.0 V
0.6 V
Amplitude
2.0 V
0.6 V
Amplitude
2.0 V
0.6 V
Amplitude
2.0 V
0.6 V
Output mode
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: On
Direct D/A out: On
Direct D/A out: On
Output mode
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: On
Direct D/A out: On
Direct D/A out: On
Output mode
Direct D/A out: Off
Direct D/A out: On
Output mode
Direct D/A out: Off
Direct D/A out: On
Output mode
Direct D/A out: Off
Direct D/A out: On
Output mode
Direct D/A out: Off
Direct D/A out: On
Minimum Incoming
17.6 mV 22.4 mV
194 mV 206 mV
488 mV 512 mV
0.978 V 1.022 V
1.958 V 2.042 V
4.408 V 4.592 V
17.6 mV 22.4 mV
194 mV 206 mV
586 mV 614 mV
17.6 mV 22.4 mV
194 mV 206 mV
488 mV 512 mV
0.978 V 1.022 V
1.958 V 2.042 V
4.408 V 4.592 V
17.6 mV 22.4 mV
194 mV 206 mV
586 mV 614 mV
none
none
none
none
none
none
none
none
Outgoing
Maximum
–40 dBc
–49 dBc
–40 dBc
–49 dBc
–40 dBc
–49 dBc
–40 dBc
–49 dBc
2–14 AWG5000B Series Arbitrary Waveform Generators Technical Reference
AWG5000B performance test record (cont.)
Performance Tests
Performance Test
Analog Harmonic Distortion (AWG500xB)
Ch 1
Ch 2
Ch 3
Ch 4
Analog Non-Harmonic Spurious
Ch1
Ch 2
Ch 3
Ch 4
Analog Phase Noise (at 10 kHz offset)
Ch 1
Ch 2
Ch 3
Ch 4
Amplitude
2.0 V
0.6 V
Amplitude
2.0 V
0.6 V
Amplitude
2.0 V
0.6 V
Amplitude
2.0 V
0.6 V
Amplitude
2.0 V
Amplitude
2.0 V
Amplitude
2.0 V
Amplitude
2.0 V
Amplitude
2.0 V
Amplitude
2.0 V
Amplitude
2.0 V
Amplitude
2.0 V
Output mode
Direct D/A out: Off
Direct D/A out: On
Output mode
Direct D/A out: Off
Direct D/A out: On
Output mode
Direct D/A out: Off
Direct D/A out: On
Output mode
Direct D/A out: Off
Direct D/A out: On
Output mode
Direct D/A out: Off
Output mode
Direct D/A out: Off
Output mode
Direct D/A out: Off
Output mode
Direct D/A out: Off
Output mode
Direct D/A out: Off
Output mode
Direct D/A out: Off
Output mode
Direct D/A out: Off
Output mode
Direct D/A out: Off
Minimum Incoming
none
none
none
none
none
none
none
none
none
none
none
none
none
none
none
none
Outgoing
Maximum
–46 dBc
–55 dBc
–46 dBc
–55 dBc
–46 dBc
–55 dBc
–46 dBc
–55 dBc
–60 dBc
–60 dBc
–60 dBc
–60 dBc
–85 dBc/Hz
–85 dBc/Hz
–85 dBc/Hz
–85 dBc/Hz
AWG5000B Series Arbitrary Waveform Generators Technical Reference 2–15
Performance Tests
AWG5000B performance test record (cont.)
Performance Test
Marker High and Low Level Accuracy
Ch 1
Ch 1
Ch 2
Mkr 1 High level setting
Mkr 2 High level setting
Mkr 1 High level setting
Minimum Incoming
+2.7 V 2 .31 V 3.09 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–0.9 V –1.11 V –0.69 V
Low level setting
+2.6 V 2 .22 V 2.98 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–1.0 V –1220 mV –780 mV
+2.7 V 2 .31 V 3.09 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–0.9 V –1.11 V –0.69 V
Low level setting
+2.6 V 2 .22 V 2.98 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–1.0 V –1220 mV –780 mV
+2.7 V 2 .31 V 3.09 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–0.9 V –1.11 V –0.69 V
Low level setting
+2.6 V 2 .22 V 2.98 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–1.0 V –1220 mV –780 mV
Outgoing
Maximum
2–16 AWG5000B Series Arbitrary Waveform Generators Technical Reference
AWG5000B performance test record (cont.)
Performance Tests
Performance Test
Ch 2
Ch 3
Ch 3
Ch 4
Mkr 2 High level setting
+2.7 V 2.31 V 3.09 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–0.9 V –1.11 V –0.69 V
Low level setting
+2.6 V 2.22 V 2.98 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–1.0 V –1220 mV –780 mV
Mkr 1 High level setting
+2.7 V 2.31 V 3.09 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–0.9 V –1.11 V –0.69 V
Low level setting
+2.6 V 2.22 V 2.98 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–1.0 V –1220 mV –780 mV
Mkr 2 High level setting
+2.7 V 2.31 V 3.09 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–0.9 V –1.11 V –0.69 V
Low level setting
+2.6 V 2.22 V 2.98 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–1.0 V –1220 mV –780 mV
Mkr 1 High level setting
+2.7 V 2.31 V 3.09 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–0.9 V –1.11 V –0.69 V
Minimum Incoming
Outgoing
Maximum
AWG5000B Series Arbitrary Waveform Generators Technical Reference 2–17
Performance Tests
AWG5000B performance test record (cont.)
Performance Test
Ch 4
Ch 4
Marker Output Delay Accuracy
Ch 1
Ch 2
Ch 3
Ch 4
DC Output Accuracy
DC output
+5 V 4.73 V 5.27 V
+3 V 2.79 V 3.21 V
0.0 V –120 mV +120 mV
–3 V –3.21 V –2.79 V
Mkr 2 High level setting
Mkr 1 700 ps 1300 ps
Mkr 2 700 ps 1300 ps
Mkr 1 700 ps 1300 ps
Mkr 2 700 ps 1300 ps
Mkr 1 700 ps 1300 ps
Mkr 2 700 ps 1300 ps
Mkr 1 700 ps 1300 ps
Mkr 2 700 ps 1300 ps
Low level setting
+2.6 V 2 .22 V 2.98 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–1.0 V –1220 mV –780 mV
+2.7 V 2 .31 V 3.09 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–0.9 V –1.11 V –0.69 V
Low level setting
+2.6 V 2 .22 V 2.98 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–1.0 V –1220 mV –780 mV
Minimum Incoming
Outgoing
Maximum
2–18 AWG5000B Series Arbitrary Waveform Generators Technical Reference
Performance Tests
10 MHz Referen
Figure 2-7: Equipment connection for verifying the 10 MHz reference frequency accuracy
ce Frequency Accuracy
Required equipment Prerequisites
Frequency counter
50 BNC c able
1. Use the 50 Ω BNC cable to connect the 10 MHz Reference Output connector on the AWG5000B to the frequency counter CH1 input.
(See page 2-8, Prerequisites.)
Analog Offset Accuracy
2. Set the frequency c ounter as follows:
a. MEASURE: Frequency1, Gate Time: 0.10 s
b. CHANNEL1: Coupling: AC, Impedance: 50
3. Press the Factory Default button on the AWG5000B.
4. Veri
5. Dis
Required equipment Prerequisites
Digital multimeter
50 BNC c able
50 BNC termination
BNC-dual banana adapter
fy that the frequency counter reading falls within the range of
9.99998 MHz to 10.00002 MHz (± 2 ppm).
connect the test setup.
(See page 2-8, Prerequisites.)
AWG5000B Series Arbitrary Waveform Generators Technical Reference 2–19
Performance Tests
Measuring the Termination
Resistance
Before verifyi of the 50BNC termination.
1. Connect the BN and LO inputs on the digital multimeter.
Figure 2-8: Equipment connection for measuring the termination resistance
2. Set the digital multimeter to the W2wiresmode.
3. Measure the resistance and note the value as Term_R.
4. Set the d
5. Disconnect the test setup.
NOTE. L
four wire ohms. The accuracy is higher especially for small resistances. Use a four wire method if necessary.
ng the analog offset acc uracy, you need to measure the resistance
C-dual banana adapter and 50 BNC termination to the HI
igital multimeter to the VDC mode.
ead resistance is not included in the measurement results when using
2–20 AWG5000B Series Arbitrary Waveform Generators Technical Reference
Performance Tests
Verifying the Analog Offset
Accuracy
1. Press the All Ou outputs.
tputs On/Off button on the AWG5000B to turn off all the
2. Use the 50 BNC cable, 50 BNC termination, and BNC-dual banana
adapter to connect the Channel 1 Analog connector on the AWG5000B to the HI and LO inputs on the digital multimeter.
Figure 2-9: Equipment connection for verifying the analog offset accuracy
3. Press the Factory Default button on the AWG5000B.
4. Press the Ch1 Select button on the AWG5000B.
5. On the AWG5000B, load the dc_zero waveform as an output waveform.
a. Select File > Open File....
b. In the dialog box, navigate to the C:\Program
Files\Tektronix\AWG\System\PV directory, and then select the pv_awg5000.awg le. The Waveform List window appears.
c. In the window, select (drag and drop) the dc_zero waveform on the User
Dened tab.
6. Press the Ch 1 On button on the AWG5000B to enable the channel 1 output.
7. Press the Run button on the AWG5000B to output the waveform.
8. Set the offset of the AWG5000B to the level shown in the rst row of the
following table:
Table 2-3: Analog offset accuracy
Offset settings Output mode settings Accuracy limits
+2.25 V
1V
Direct D/A out: Off
Direct D/A out: Off
2190 mV to 2310 mV
965 mV to 1035 mV
AWG5000B Series Arbitrary Waveform Generators Technical Reference 2–21
Performance Tests
Table 2-3: Analog offset accuracy (cont.)
Offset settings Output mode settings Accuracy limits
0.0 V
–1 V
–2.25 V
N/A (0 V) Direct D/A out: On
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
–15 mV to +15 mV
–1035 mV to –965 mV
–2310 mV to –2190 mV
–15 mV to + 15 mV
9. Measure t
he output voltage on the digital multimeter and note the value as
Measured_voltage.
10. Use the f
ollowing formula to compensate the voltage for the 50 BNC
termination:
e = [(Term_R + 50) /(2 × Term_R)] × Measured_voltage
Voltag
Where Term_R is the resistance of the 50 BNC termination measured in
.(Seepage2-20,Measuring the Termination Resistance.)
step 3
11. Verify that the calculated value falls within the limits given in the table. Table 2-3. )
(See
12. Repeat steps 8 through 11 for each offset setting in the table. (See Table 2-3.)
13. Move the BNC termination from the Channel 1 Analog connector to the
Channel 1 A
nalog connector.
14. Repeat steps 8 through 12.
15. Repeat steps 6 through 14 for the Channel 2 output.
16. For the AWG5014B or AWG5004B: Repeat the test for the Channel 3 and
Channel 4 outputs.
17. Press the All Outputs On/Off button on the AWG5000B to turn off all the
outputs.
18. Disconnect the test setup.
2–22 AWG5000B Series Arbitrary Waveform Generators Technical Reference
Analog Amplitude Accuracy
Required equipment Prerequisites
Digital multimeter
50 BNC c able
50 BNC termination
BNC-dual banana adapter
1. Perform Measuring the Termination Resistance. (Seepage2-20.)
2. Press the All Outputs On/Off button on the AWG5000B to turn off all the
outputs.
3. Use the 50 BNC cable, 50 BNC termination, and BNC-dual banana adapter to connect the Channel 1 Analog connector on the AWG5000B to the HI and LO inputs on the digital multimeter. (See Figure 2-9.)
4. Press the Factory Default button on the AWG5000B.
5. Press the Ch 1 Select button on the AWG5000B.
Performance Tests
(See page 2-8, Prerequisites.)
6. On the AWG5000B, load the dc_plus waveform as an output waveform.
a. Select File > Open File....
b. In the dialog box, navigate to the C:\Program
Files\Tektronix\AWG\System\PV directory, and then select the pv_awg5000.awg le. The Waveform List window appears.
c. In the window, select (drag and drop) the dc_plus waveform on the User
Dened tab.
7. Press the Ch 1 On button on the AWG5000B to enable the channel 1 output.
8. Press the Run button on the AWG5000B to output the waveform.
9. Set the amplitude and output mode of the AWG5000B as shown in the rst
row of the table. (See Table 2-4.)
e 2-4: Analog amplitude accuracy
Tabl
Amplitude settings Output mode settings Accuracy limits
p-p
20 mV
mVp-p
200
mVp-p
500
0 Vp-p
1.
0 Vp-p
2.
.5 Vp-p
4
0 mVp-p
2
200 mVp-p
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: On
Direct D/A out: On
mV to 22.4 mV
17.6
mV to 206 mV
194
mV to 512 mV
488
978 V to 1.022 V
0.
958 V to 2.042 V
1.
.408 V to 4.592 V
4
7.6mVto22.4mV
1
194 mV to 206 mV
AWG5000B Series Arbitrary Waveform Generators Technical Reference 2–23
Performance Tests
Table 2-4: Analog amplitude accuracy (cont.)
Amplitude setting s Output mode settings Accuracy limits
600 mVp-p
Direct D/A out: On
586 mV to 614 mV
10. Measure th
e output voltage on the digital multimeter and note the value as
Measured_voltage_1.
11. Use the fo
llowing formula to compensate the voltage for the 50 BNC
termination:
V_high = [
(Term_R + 50) / (2 × Term_R)] ×Measured_voltage_1
Where Term_R is the resistance of the 50 BNC termination measured in step 3. (
Seepage2-20.)
12. In the Waveform List window, select the dc_minus waveform on the User
Dened
tab.
13. Measure the output voltage on the digital multimeter and note the value as
Measu
red_voltage_2.
14. Use the following formula to compensate the voltage for the 50 BNC
ination:
term
V_low = [(Term_R + 50) / (2 × Term_R)] × Measured_voltage_2
Where Term_R is the resistance of the 50 BNC termination measured in step 3. (See page 2-20.).
15. Verify that the voltage difference |(V_high-V_low)| falls within the limits given in the table. (See Table 2-4.)
16. Repeat steps 9 through 15 for each amplitude setting in the table. (See Table 2-4.)
17. Move the BNC termination from the Channel 1 Analog connector to the Channel 1 A
nalog connector.
2–24 AWG5000B Series Arbitrary Waveform Generators Technical Reference
Performance Tests
18. Repeat steps 9 t
19. Repeat steps 7 through 18 for the Channel 2 output.
20. For the AWG5014B or AWG5004B: Repeat the test for the Channel 3 and
Channel 4 outputs.
21. Press the All Outputs On/Off button on the AWG5000 to turn off all the outputs.
22. Disconnect the test setup.
Analog Harmonic Distortion
Required equipment Prerequisites
Spectrum analyzer
50 BNC c able
BNC-N adapter
1. Press the All Outputs On/Off button on the AWG5000B to turn off all the outputs.
2. Use the 50 BNC cable and BNC-N adapter to connect the Channel 1 Analog connector on the AWG5000B to the INPUT connector on the spectrum analyzer.
hrough 16.
(See page 2-8, Prerequisites.)
Figure 2-10: Equipment connections for verifying the analog harmonic distortion
3. Set the spectrum analyzer as follows:
a. Center frequency: 100 MHz
b. Span: 200 MHz
c. RBW: 20 kHz
4. Press the Factory Default button on the AWG5000B.
AWG5000B Series Arbitrary Waveform Generators Technical Reference 2–25
Performance Tests
5. Press the Ch 1 Se
6. On the AWG5000B, load the sine_32 waveform as an output waveform.
7. Press the Ch 1 On button on the AWG5000B to enable the channel 1 output.
8. Press the Run button on the AWG5000B to output the waveform.
9. Make the AWG5000B settings shown in the rst row (or corresponding row
Table 2-5: Analog harmonic distortion
AWG500
Model
AWG501xB
AWG500xB
0B model and settings
tmode
Outpu
Direct D/A out: Off
Direct D/A out: On
Direct D/A out: Off
Direct D/A out: On
Amplitude
2.0 Vp-p –40 dBc
0.6 Vp-p
2.0 Vp-p –46 dBc
0.6 Vp-p
lect button on the AWG5000B.
a. Select File > Open File....
b. In the dialog box, navigate to the C:\Program
Files\Tektronix\AWG\System\PV directory, and then select the pv_awg5000.awg le. The Waveform List window appears.
c. In the window, select (drag and drop) the sine_32 waveform on the User
Dened tab.
for your instrument) of the following table:
Accuracy limit
ference
Nth re
–49 dBc
–55 dBc
ing
Sampl rate (output frequency)
1.2 GS/s 5MHz)
(37.
600 MS/s
.75 MHz)
(18
ement frequency (MHz)
Measur
2nd 3rd 4th 5th
75
37.5 56.25
112.5 150 187.5
75
93.75
10. Use the delta measurement function of the spectrum analyzer to measure rmonic distortion of each measurement frequency.
ha
11. Verify that the harmonic distortion falls within the limits given in the table.
See Table 2-5.)
(
12. Repeat steps 9 through 11 for each setting in the table. (See Table 2-5.)
13. Move the 50 BNC cable from Channel 1 Analog connector to the
Channel 2 Analog connector.
14. Repeat steps 7 through 12 for the Channel 2 output.
15. For the AWG5014B or AWG5004B: Repeat the test for the Channel 3 and
Channel 4 outputs.
16. Press the All Outputs On/Off button on the AWG5000B to turn off all the
outputs.
17. Disconnect the test setup.
2–26 AWG5000B Series Arbitrary Waveform Generators Technical Reference
Performance Tests
Analog Non-Ha
rmonic Spurious Signal
Required equipment Prerequisites
Spectrum analyzer
50 BNC c able
BNC-N adapter
1. Press the Al outputs.
2. Use the 50 connector on the AWG5000B to the INPUT connector on the spectrum analyzer.
l Outputs On/Off button on the AWG5000B to turn off all the
BNC cable and BNC-N adapter to connect the Channel 1 Analog
(See page 2-8, Prerequisites.)
Figure 2-11: Equipment connections for verifying the non-harmonic spurious signal
3. Press the Factory Default button on the AWG5000B.
4. Press the Ch1 Select button on the AWG5000B.
5. On
6. Press the Ch 1 On button on the AWG5000B to enable the channel 1 output.
7. Press the Run button on the AWG5000B to output the waveform.
the AWG5000B, load the sine_32 waveform as an output waveform.
a. Select File > Open File....
b. In the dialog box, navigate to the C:\Program
Files\Tektronix\AWG\System\PV directory, and then select
he pv_awg5000.awg le. The Waveform List window appears.
t
c. In the window, select (drag and drop) the sine_32 waveform on the User
Dened tab.
AWG5000B Series Arbitrary Waveform Generators Technical Reference 2–27
Performance Tests
8. Make the AWG500
0B and spectrum analyzer settings shown in the rst row
or the second row of the following table:
Table 2-6: Analog non-harmonic spurious signal
AWG5000B model and settings Spectrum analyzer settings
Model
AWG501xB Direct D/A out:
AWG500xB Direct D/A out:
Output mode
Off
Off
Amplitude
2.0 Vp-p
2.0 Vp-p
Sampling rate (outpu frequency)
1.2 GS/s (37.5 MHz)
600 MS/s (18.75 MH
Center
t
frequency
400 MHz 800 MHz 20 kHz –60 dBc
200 MHz 400 MHz 20 kHz –60 dBc
z)
Span
9. Use the spectrum analyzer to measure non-harmonic spurious signal of the Analog output over a frequency range of DC to 600 MHz (for the AWG500xB, DC to 300 MHz). For example, note the reference level of the fundamental waveform, and then measure each spurious.
10. Verify that the non-harmonic spurious signal falls within the limits given in the table. (See Table 2-6.)
11. Move the 50 BNC cable from the Channel 1 Analog connector to the Channel 2 Analog connector.
RBW Accuracy limit
Analog Phase Noise
12. Repeat steps 6 through 10 for the Channel 2 output.
13. For the AWG5014B or AWG5004B: Repeat the test for the Channel 3 and
Channel 4 outputs.
14. Press the All Outputs On/Off button on the AWG5000B to turn off all the outputs.
15. Disconnect the test setup.
Required equipment Prerequisites
Spectrum analyzer
50 BNC cable
BNC-N adapter
(See page 2-8, Prerequisites.)
1. Press the All Outputs On/Off button on the AWG5000B to turn off a ll the outputs.
2. Use the 50 BNC cable and BNC-N adapter to connect the Channel 1 Analog connector on the AWG5000B to the INPUT connector on the spectrum analyzer.
2–28 AWG5000B Series Arbitrary Waveform Generators Technical Reference
Performance Tests
Figure 2-1
2: Equipment connections for verifying the analog phase noise
3. Press the
Factory Default button on the AWG5000B.
4. On the AWG5000B, load the sine_32 waveform as an output waveform.
a. Select File > Open File....
b. In the dialog box, navigate to the C:\Program
Files\Tektronix\AWG\System\PV directory, and then select the pv_awg5000.awg le. The Waveform List window appears.
c. In the window, select (drag and drop) the sine_32 waveform on the User
Dened tab.
5. Press the Ch 1 On button on the AWG5000B to enable the channel 1 output.
6. Press the Run button on the AWG5000B to output the waveform.
7. Make the AWG5000B and spectrum analyzer settings shown in the rst row
(or the second row for your instrument) of the table. (See Table 2-7.)
8. Use the spectrum analyzer to measure phase noise of the Analog output.
9. Verify that the analog phase noise at 10 kHz offset falls within the limits
given in the following table:
Table 2-7: Analog phase noise
AWG5000B model and settings Spectrum analyzer settings
Model
AWG501xB Direct D/A out:
AWG500xB Direct D/A out:
Output mode
Off
Off
Amplitude
2.0 Vp-p
2.0 Vp-p
Sampling rate
1.2 GS/s
600 MS/s
Center frequency
37.5 MHz 50 kHz 100 Hz
18.75 MHz 50 kHz 100 Hz
Span
RBW Accuracy Limit
at 10 kHz offset
–85 dBc/Hz
–85 dBc/Hz
AWG5000B Series Arbitrary Waveform Generators Technical Reference 2–29
Performance Tests
10. Move the 50 BNC Channel 2 Analog connector.
11. Repeat steps 5
12. For the AWG5014B or AWG5004B: Repeat the test for the Channel 3 and
Channel 4 ou
13. Press the All Outputs On/Off button on the AWG5000B to turn off all the outputs.
14. Disconnect the test setup.
through 9 for the Channel 2 output.
tputs.
cable from the Channel 1 Analog connector to the
Figure 2-13: Example of the analog phase noise measurement
2–30 AWG5000B Series Arbitrary Waveform Generators Technical Reference
Marker High and Low Level A ccuracy
Required equipment Prerequisites
Digital multimeter
50 BNC c able
50 BNC termination
BNC-dual banana adapter
1. Perform Measuring the Termination Resistance. (Seepage2-20.)
2. Press the All Outputs On/Off button on the AWG5000B to turn off all the
outputs.
3. Use the 50 BNC cable, 50 BNC termination, and BNC-dual banana adapter to connect the Channel 1 Mkr 1 connector on the AWG5000B to the HI and LO inputs on the digital multimeter.
Performance Tests
(See page 2-8, Prerequisites.)
Figure 2-14: Equipment connection for verifying the marker high and low level accuracy
4. Press the Factory Default button on the AWG5000B.
ess the Ch1 Select button on the AWG5000B.
5. Pr
6. On the AWG5000B, load the marker_hi waveform as an output waveform.
a. Select File > Open File....
b. In the dialog box, navigate to the C:\Program Files\Tektronix\AWG\
System\PV directory, and then select the pv_awg5000.awg le. The Waveform List window appears.
c. In the window, select the marker_hi waveform on the User Defined tab.
7. Press the Ch 1 On button on the AWG5000B to enable the channel 1 output.
8. Press the Run button on the AWG5000B to output the waveform.
AWG5000B Series Arbitrary Waveform Generators Technical Reference 2–31
Performance Tests
9. Make the AWG500
0B High Level setting shown in the rst row of the
following table:
Table 2-8: Marker High and Low level accuracy
High level settings Accuracy limits
+2.7 V 2.31 V to 3.09 V
+1.0 V 780 mV to 1220 mV
0.0 V –120 mV to +120 mV
–0.9 V –1.11 V to 0.69 V
Low level settings Accuracy limits
+2.6 V 2.22 V to 2.98 V
+1.0 V 780 mV to 1220 mV
0.0 V –120 mV to +120 mV
–1.0 V –1220 mV to –780 mV
10. Measure the output voltage on the digital multimeter and note the value as Measured_voltage_1.
11. Use the following formula to compensate the voltage for the 50 BNC
termination:
Marker_High = (Term_R + 50) / (2 Term_R) Measured_voltage_1
Where Term_R is the resistance of the 50 BNC termination measured in step 3. (See page 2-20.)
12. Verify that the marker High level falls within the limits given in the table. (See Table 2-8.)
13. Repeat steps 9 through 12 for each row in the table. (See Table 2-8.)
14. In the Waveform List window, select the marker_low waveform on the User Dened tab.
15. Press the Ch 1 On button on the AWG5000B to enable the c hannel 1 output.
16. Press the Run button on the AWG5000B to output the waveform.
17. Make the AWG5000B Low Level setting shown in the rst row of the table.
18. Measure the output voltage on the digital multimeter and note the value as Measured_voltage_2.
19. Use the following formula to compensate the voltage for the 50 BNC
termination:
Marker_Low = (Term_R + 50) / (2 Term_R) Measured_voltage_2
Where Term_R is the resistance of the 50 BNC termination measured in step 3. (See page 2-20.)
20. Verify that the marker Low level falls within the limits given in the table.
2–32 AWG5000B Series Arbitrary Waveform Generators Technical Reference
Performance Tests
21. Repeat steps 17
22. Press the Ch 1 On button to disable the channel 1 output.
23. Move the BNC termination from the Channel 1 Mkr 1 connector to the
Channel 1 Mkr 2 connector.
24. Repeat steps 7 through 21.
25. Move the 50 BNC termination from Channel 1 Mkr 2 connector to the
Channel 2 Mkr 1 connector.
26. Repeat steps 7 through 24 for the Channel 2 marker outputs.
27. For the AWG5014B or AWG5004B: Repeat the test for the Channel 3 and
Channel 4 marker outputs.
28. Press the All Outputs O n/Off button on the AWG5000B to turn off all the outputs.
29. Disconnect the test setup.
Marker Output Delay A ccuracy
Required equipment Prerequisites
Sampling oscilloscope
Two 50 BNC cable
Two BNC-SMA adapters
through20foreachrowinthetable.
(See page 2-8, Prerequisites.)
1. Press the All Outputs On/Off button on the AWG5000B to turn off all the outputs.
2. Use a 50 BNC cable and BNC-SMA adapter to connect the Channel 1 Mkr 1 connector on the AWG5000B to the CH1 connector on the sampling
cilloscope.
os
3. Use the 50 BNC cable and BNC-SMA adapter to connect the Channel 1
kr 2 connector on the AWG5000B to the TRIGGER DIRECT connector on
M the sampling oscilloscope.
AWG5000B Series Arbitrary Waveform Generators Technical Reference 2–33
Performance Tests
Figure 2-15: Equipment connections for verifying the marker output delay accuracy
4. Set the sampling oscilloscope as follows:
a. Vertical scale: 250 mV/div
b. Horizontal sc ale: 500 ps/div
c. Trigger source: External Direct
d. Trigger level: 150 mV (or Set to 50%)
e. Trigger slope: positive
f. Measure: Pulse measurement > Pulse Time > Delay
5. Press the Factory Default button on the AWG5000B.
6. On the AWG5000B, load the square1 waveform as an output waveform.
a. Select File > Open File....
b. In the dialog box, navigate to the C:\Program Files\Tektronix\AW G\
System\PV directory, and then select the pv_awg5000.awg le. The Wavef orm List window appears.
c. In the window, select the square1 waveform on the User Dened tab.
7. Press the Ch 1 On button on the AWG5000B to enable the channel 1 output.
8. Press the Run button on the AWG5000B to output the waveform.
9. On the oscilloscope, store the channel 1 waveform to Ref 1 as a reference
waveform.
10. On the AWG5000B, set the Marker 1 delay value to 1.00 ns.
2–34 AWG5000B Series Arbitrary Waveform Generators Technical Reference
Performance Tests
11. Use the oscillo and channel 1 waveform at the 50% level.
12. Verify that th
13. Press the Ch 1 On button on the AWG5000B to disable the channel 1 output.
14. Move the 50 BNC cable from the Channel 1 Mkr 1 connector to the
Channel 1 Mkr 2 connector and from Channel 1 Mkr 2 connector to the Channel Mkr
15. Press the Ch 1 On button on the AWG5000B to enable the channel 1 output.
16. On the oscilloscope, store the c hannel 1 waveform to Ref 1 as a reference
waveform.
17. On the AWG5000B, set the Marker 2 delay value to 1.00 ns.
18. Repeat steps 11 and 12.
19. Repeat steps 7 through 18 for the Channel 2 markers.
20. For the AWG5014B and AWG5004B: Repeat the test for the Channel 3 and
Channel 4 marker outputs.
21. Press the All Outputs O n/Off button on the AWG5000B to turn off all the outputs.
scope to measure the delay time between the Ref 1 w aveform
e delay time is within the range of 700 ps to 1300 ps.
1 connector.
22. Disconnect the test setup.
AWG5000B Series Arbitrary Waveform Generators Technical Reference 2–35
Performance Tests
DC Output Volt
age Accuracy
Required equipment Prerequisites
Digital multime ter
DC output lead set
Test leads (provided with the digital multimeter)
1. Use the test
2. Use the DC output lead set to connect the DC Output connector on the
AWG5000B a
(See page 2-8, Prerequisites.)
leads to connect the HI and LO inputs on the digital multimeter.
s shown in the following gure.
Figure 2-16: Equipment connection for verifying the DC output voltage accuracy
3. Set the digital multimeter to the VDC mode.
4. On the AWG5000B, select the DC Outputs tab in the Settings window.
5. OntheDCOutputtab,settheDC1,DC2,DC3,andDC4levelstothe
setting shown in the rst row of the following table:
Table 2-9: DC output voltage accuracy
DC output settings Accuracy limits
+5 V 4.73 V to 5.27 V
+3 V 2.79 V to 3.21 V
0.0 V –120 mV to +120 mV
2–36 AWG5000B Series Arbitrary Waveform Generators Technical Reference
Performance Tests
Table 2-9: DC output voltage accuracy (cont.)
DC output settings Accuracy limits
–3 V –3.21 V to –2.79 V
6. On the DC Outputs tab, select the DC Output check box to enable the DC output. The DC Output LED on the front panel lights.
7. Attach the black test lead to the connector lead from DC1 GND.
8. Attach the red test lead to the connector lead from DC1.
9. Verify that the DC output level falls within the limits given in the table.
(See Table 2-9.)
10. Repeat steps 8 and 9 for DC 2, DC 3, and DC 4.
11. Repeat steps 5 through 10 for each row in the table. (See Table 2-9.)
This co
mpletes the AWG5000B performance verication.
AWG5000B Series Arbitrary Waveform Generators Technical Reference 2–37
Loading...