xx
065-0811-00 and Above
Hard Disk Drive Assembly Without Software
AWG5000B and AWG7000B Series
ZZZ
Arbitrary Waveform Generators
www.tektronix.com
075097000*
*P
075-0970-00
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14200 SW Karl Braun Drive
P.O . Bo x 5 0 0
Beaverton, O
USA
For product information, sales, service, and technical support:
In North America, call 1-800-833-9200.
Worl d wide , visi t www.tektronix.com to find contacts in your area.
R 97077
Assembly Description
This document supports the following hard disk drive assembly:
065-0811-XX
NOTE. After you replace this assembly, you need to reinstall the operating system
and application software.
Products
Minimum Tool and
Equipment List
AWG5002B, AWG5004B, AWG5012B, AWG5014B
AWG7061B, A
To install the operating system and application software after you replace the hard
disk drive assembly, you need the following software:
Product Software CD Package for the AWG5000B and AWG7000B series
Operating system restore disks that you created using the procedure in the
AWG5000B and AWG7000B series Quick Start User Manual
NOTE. The operating system restore disks are not available for this product. Use
the CD-RO
series instrument. If you have not already created the restore CD-ROMs, follow
the procedure in the Quick Start User Manual to create a set of restore disks.
WG7062B, AWG7121B, AWG7122B
Ms you created when you first used the AWG5000B or AWG7000B
Hard Disk Assembly Instructions 1
Installation Instructions
Installation Instructions
This section describes how to install theharddiskdriveassemblyintoyour
instrument.
Installation Procedures
CAUTION. Before you remove or insert the hard disk drive assembly, make sure
that the instrument is powered off. Failure to disconnect the power from the
instrument may result in damage to the hard disk drive.
Removing the Hard Disk
Drive Assembly
1. Unplug the power cord from the power connector on the rear panel.
2. Position the instrument on the work surface with the rear panel fa cing you as
shown.
3. Loosen the two thumb screws securing the hard disk drive assembly to the
instrument.
4. Slowly pull the hard disk drive assembly toward you. Note the orientation of
the assembly as you remove it.
Installing the Replacement
Hard Disk Drive Assembly
2 Hard Disk Assembly Instructions
1. Orient the replacement assembly the same way as the original assembly.
Install the replacement into the hard disk drive slot.
2. Push the hard disk drive assembly in until the data and power connectors are
firmly engaged with the instrument.
3. Tighten the two thumbscrews to secure the hard disk drive assembly to the
instrument.
Installation Instructions
Reinstalling the Software
After you have i
instrument, you need to reinstall the Microsoft Windows XP operating system and
application software onto the hard disk drive.
Refer to the following documents for information on how to install the software:
Touch Screen Adjustment
Perform the following steps to adjust the touch screen of the instrument:
1. Double-cli
2. Follow the
nstalled the replacement hard disk drive assembly into the
AWG5000B and
the Windows XP Operating System
Product Soft
instruments
start the touch screen program.
pen that was shipped with the instrument.
AWG7000B Series Quick Start User Manual for restoring
ware CD Instructions for the AWG5000B and AWG7000B series
ck the Touch screen configurator icon on the Windows desktop to
on-screen instructions to complete the adjustment using the stylus
Hard Disk Assembly Instructions 3
Loading...