Tektronix AWG5002C, AWG5012C, AWG5014C Performance Verification

xx
AWG5000C Series Arbitrary Waveform Generators
ZZZ
Specications and Performance Verication
Technical Reference
www.tektronix.com
*
077-0455-01
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material. Specications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
TekLink is a trademark of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc. 14150 SW Karl Braun Drive P.O. B o x 5 0 0 Beaverton, OR 97077 USA
For product information, sales, service, and technical support:
In North America, call 1-800-833-9200. Worl dwid e, v isit www.tektronix.com to nd contacts in your area.
Warranty
Tektronix warrants that this product will be free from defects in materials and workmanship for a period of one (1) year from the date of shipment. If any such product proves defective during this warranty period, Tektronix, at its option, either will repair the defective product without charge for parts and labor, or will provide a replacement in exchange for the defective product. Parts, modules and replacement products used by Tektronix for warranty work may be n the property of Tektronix.
ew or reconditioned to like new performance. All replaced parts, modules and products become
In order to o the warranty period and make suitable arrangements for the performance of service. Customer shall be responsible for packaging and shipping the defective product to the service center designated by Tektronix, with shipping charges prepaid. Tektronix shall pay for the return of the product to Customer if the shipment is to a location within the country in which the Tektronix service center is located. Customer shall be responsible for paying all shipping charges, duties, taxes, and any other charges for products returned to any other locations.
This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate maintenance and care. Tektronix shall not be obligated to furnish service under this warranty a) to repair damage result b) to repair damage resulting from improper use or connection to incompatible equipment; c) to repair any damage or malfunction caused by the use of non-Tektronix supplies; or d) to service a product that has been modied or integrated with other products when the effect of such modication or integration increases the time or difculty of servicing the product.
THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THE PRODUCT IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
TRONIX’ RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE
TEK AND EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY. TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.
[W2 – 15AUG04]
btain service under this warranty, Customer must notify Tektronix of the defect before the expiration of
ing from attempts by personnel other than Tektronix representatives to install, repair or service the product;
Table of Contents
General Safety Summary ......................................................................................... iv
Service Safety Summary.................................. ................................ ........................ vi
Preface ............................................................................................................. vii
Related Doc
Specications .................. .................................. ................................ ................... 1
Performance Conditions ...................................................................................... 1
Electrical Specications...................... .................................. ............................... 2
Mechanical (Physical) Characteristics...................................................................... 12
Environmental Characteristics .............................................................................. 13
Perform
Brief Procedures ............................. ................................ .................................. .... 15
Performance Tests ................. ................................ .................................. .............. 22
ance Verication Procedures............................................................................ 15
Diagnostics .................................................................................................... 15
Self Calibration ................... ................................ .................................. .......... 17
Functional Test................................................................................................ 17
equisites....... ................................ ................................ ............................ 22
Prer
Required Equipment.............................. ................................ ............................ 23
Test Record .......................... ................................ .................................. ........ 25
10 MHz Reference Frequency Accuracy................... ................................ ................ 34
Analog Offset Accuracy ..................................................................................... 34
Analog Amplitude Accuracy .... . .... . ..... . ..... . .... . . .... . ..... . ..... . .... . ..... . ..... . .... . . .... . ..... . . 38
alog Harmonic Distortion .................... .................................. .......................... 40
An
Analog Non-Harmonic Spurious Signal................ .................................. .................. 42
Analog Phase Noise ........ .................................. ................................ ................ 43
Marker High and Low Level Accuracy ................ .................................. .................. 46
Marker Output Delay Accuracy............................................................................. 48
DC Output Voltage Accuracy ............................................................................... 51
uments.......................................................................................... vii
AWG5000C Series Arbitrary Waveform Generators Technical Reference i
Table of Contents
List of Figure
Figure 1: Diagnostics dialog box .................... ................................ ............................ 16
Figure 2: Ca
Figure 3: Equipment connections for checking the analog and marker outputs.......... .................. 18
Figure 4: Output waveform from the Analog, Mkr 1, and Mkr 2 outputs............................. ...... 19
Figure 5: Equipment connection for checking the digital data outputs........................ .............. 20
Figure 6: Output waveform from the Digital Data Out connector ........................................... 21
Figure 7: Equipment connection for verifying the 10 MHz reference frequency accuracy ............... 34
Figure 8:
Figure 9: Equipment connection for verifying the analog offset accuracy...................... ............ 36
Figure 10: Equipment connections for verifying the analog harmonic distortion .......................... 40
Figure 11: Equipment connections for verifying the non-harmonic spurious signal.... . .... . ..... . .... . .. 42
Figure 12: Equipment connections for verifying the analog phase noise ....... ............................ 44
Figure 13: Example of the analog phase noise measurement........................................... ...... 45
e 14: Equipment connection for verifying the marker high and low level accuracy. . ..... . ..... . ... 46
Figur
Figure 15: Equipment connections for verifying the marker output delay accuracy............... ........ 49
Figure 16: Equipment connection for verifying the DC output voltage accuracy.......................... 51
libration dialog box ................................................................................. 17
Equipment connection for measuring the termination resistance............. .................... 35
s
ii AWG5000C Series Arbitrary Waveform Generators Technical Reference
List of Tables
Table 1: Run mode .................. ................................ .................................. ............. 2
Table 2 : Arb
Table 3: Clock generator........................................................................................... 3
Table 4: Trigger generator ......................................................................................... 3
Table 5: Inter-channel skew control ........................... ................................ ................... 3
Table 6: Waveform rotation control for analog output ......................................................... 4
Table 7: Analog output............................................................................................. 4
Table 8 : M
Table 9: Digital data output (Option 03 only).......... .................................. ....................... 7
Table 10: Trigger and gate input.................................................................................. 7
Table 11: Event input ......... .................................. ................................ ................... 8
Table 12: Reference clock input ................... ................................ ............................... 8
Table 13: Oscillator (External clock) input .... . ..... . ... . . . .... . ..... . ..... . .... . ..... . ..... . .... . . .... . ..... . .. 9
Table
Table 15: DC output................................................................................................ 9
Table 16: Oscillator output ..... . ..... . ..... . ..... . ... . . ..... . ..... . ..... . ..... . ..... . ... . . . .... . ..... . ..... . ..... . 9
Table 17: Dynamic Jump In for Option 09 Only... ................................ ............................ 10
Table 18: 10 MHz clock output .................................................................................. 11
Table 19: TekLink port............................................................................................ 11
ble 20: CPU module and peripheral devices................................................................. 11
Ta
Table 21: Display .................................................................................................. 11
Table 22: Power supply. ................................ ................................ .......................... 12
Table 23: Mechanical characteristics............................................................................ 12
Table 24: Environmental characteristics........................................................................ 13
Table 25: Required equipment ................................................................................... 23
Table 26: Test waveforms ........................................................................................ 24
Table 27: Analog offset accuracy........................ .................................. ...................... 36
Table 28: Analog amplitude accuracy.... . ..... . ..... . ..... . .... . . .... . ..... . ..... . ..... . ..... . ..... . .... . ..... . 38
Table 29: Analog harmonic distortion....... .................................. ................................ .. 41
Table 30: Analog non-harmonic spurious signal............................................................... 43
Table 31: Analog phase noise .......... .................................. ................................ ........ 44
Table 32: Marker High and Low level accuracy . ................................ .............................. 47
Table 33: DC output voltage accuracy ...... ................................ .................................. .. 51
itrary waveform ..................... .................................. ............................... 2
arker output............................................................................................. 6
14: Add input ..................... .................................. ................................ ......... 9
Table of Contents
AWG5000C Series Arbitrary Waveform Generators Technical Reference iii
General Safety Summary
General Safet
To Avoid Fi
re or Personal
Injury
ySummary
Review the fo this product or any products connected to it.
To avoid pot
Only qualied personnel should perform service procedures.
Use proper
certied for the country of use.
Ground th
of the power cord. To avoid electric shock, the grounding conductor must be connected to earth ground. Before making connections to the input or output terminals of the product, ensure that the product is properly grounded.
Observe all terminal ratings. To avoid re or shock hazard, observe all ratings and markings on the product. Consult the product manual for further ratings information before making connections to the product.
Do not apply a potential to a ny terminal, including the common terminal, that exceeds the maximum rating of that terminal.
llowing safety precautions to avoid injury and prevent damage to
ential hazards, use this product only as specied.
power cord. Use only the power cord specied for this product and
eproduct.This product is grounded through the grounding conductor
Power disconnect. The power cord disconnects the product from the power source.
Donotblockthepowercord;itmustremain accessible to the user at all times.
Do not operate without covers. Do not operate this product with covers or panels removed.
Do not operate with suspected failures. If you suspect that there is damage to this product, have it inspected by qualied service personnel.
Avoid exposed circuitry. Do not touch exposed connections and components when power is present.
Do not operate in wet/damp conditions.
Do not operate in an explosive atmosphere.
Keep product surfaces clean and dry.
Provide proper ventilation. Refer to the manual’s installation instructions for
details on installing the product so it has proper ventilation.
iv AWG5000C Series Arbitrary Waveform Generators Technical Reference
General Safety Summary
TermsinThisManual
Symbols and Terms on the
Product
These terms may
WAR NI NG . Warning statements identify conditions or practices that could result
in injury or loss of life.
CAUTION. Caution statements identify conditions or practices that could result in
damage to this product or other property.
These terms may appear on the product:
DANGER in the marking.
WARNING read the marking.
CAUTIO
The following symbol(s) may appear on the product:
appear in this manual:
dicates an injury hazard immediately accessible as you read
indicates an injury hazard not immediately accessible as you
N indicates a hazard to property including the product.
AWG5000C Series Arbitrary Waveform Generators Technical Reference v
Service Safety Summary
Service Safet
y Summary
Only qualifie Safety Summary and the General Safety Summary before performing any service procedures.
Do Not Service Alone. Do not perform internal service or adjustments of this product unless another person capable of rendering rst aid and resuscitation is present.
Disconnect Power. To avoid electric shock, switch off the instrument power, then disconnect the power cord from the mains power.
Use Care When Servicing With Power On. Dangerous voltages or currents may exist in disconnect test leads before removing protective panels, soldering, or replacing components.
To avoid electric shock, do not touch exposed connections.
d personnel should perform service procedures. Read this Service
this product. Disconnect power, remove battery (if applicable), and
vi AWG5000C Series Arbitrary Waveform Generators Technical Reference
Preface
Related Documents
This manual contains specications and performance verication procedures for the AWG5000C Series Arbitrary Waveform Genera t ors.
The following user documents are also available for this product:
AWG5000 and AWG7000 Series Arbitrary Waveform Generators Quick Start User Manual. This document describes the functions and use of the
instrume
AWG5000 Series Arbitrary Waveform Generators Service Manual.Thisisa PDF only m downloaded from the Tektronix Web site.
nt.
anual that provides module-level service information. It can be
AWG5000C Series Arbitrary Waveform Generators Technical Reference vii
Preface
viii AWG5000C Series Arbitrary Waveform Generators Technical Reference
Specications
This section contains the specications for the instruments.
All specifications are guaranteed unless noted as (Typical ). Typical specifications are provided for your convenience but are not guaranteed. Specications that are marked with the
Performance Conditions
To meet specications, following conditions must be met:
symbol are checked in this manual.
The instrument must have been calibrated/adjusted at an ambient temperature between +20 °C and +30 °C (68 °F and 86 °F)
The instrument must be operating within the environmental limits. (See Table 24 on page 13.)
The instrument must be powered from a source that meets the specications. (See Table 22 on page 12.)
The instrument must have been operating continuously for at least 20 minutes within the specified operating temperature range.
AWG5000C Series Arbitrary Waveform Generators Technical Reference 1
Specications
Electrical Sp
ecications
Table 1: Run mode
Characteris
Continuous m
Triggered mode
Gated mode An arbitrary waveform is output only when a gate signal is asserted. The waveform output
Sequence
tics
ode
mode
Description
An arbitrary
An arbitrar is output, the instrument waits for the next trigger signal.
is repeated while the gate signal stays asserted. When the gate signal is deasserted, the waveform o
Standard Option 08: Fast sequence switching
waveform is output continuously.
y waveform is output only once when a trigger signal is applied. After the waveform
utput stops immediately.
: Sequence switching with wait trigger
Table 2: Arbitrary waveform
Characteristics Description
Waveform length
Without Option 01
With O p tion 01
Hardware limitation 250 points minimum
Waveform granularity
DAC resolution
Number of waveforms Up to 32,000 waveforms (predened waveforms are not included.)
Sequence l ength
Sequence controls
Without Option 08 Repeat count, Wait-for-Trigger (On only), Go-to-N, and Jump are available
Option 08 Repeat count, Wait-for-Trigger (On or Off), Go-to-N, and Jump are available
Repeat count
Jump timing
Sequence switching time (Typical)
AWG5012C, AWG5014C
AWG5002C
1 to 16,200,000 points
1 to 32,400,000 points
1 point
14 bits
1 to 8,000 steps
1 to 65,536 or in nite (all channels operate the same sequence)
Synchronous or Asynchronous selectable
2.1 ns
4.2 ns
2 AWG5000C Series Arbitrary Waveform Generators Technical Reference
Specications
Table 3: Clock g
enerator
Characteristics Description
Sampling rate control
Range
AWG5002C 10.0000 MS/s to 0.6000 GS/s
AWG5012C, AWG5014C 10.0000 MS/s to 1.2000 GS/s
Resolution 8 digits
Internal clock frequency
Internal clock frequency accuracy
Within ± (1 ppm + aging)
Aging: within ± 1 ppm/year
(Typ ical)
Referenc
Referenc
e oscillator accuracy
e oscillator a ccuracy
Within ± (1 ppm + aging)
Aging: wi
thin ± 1 ppm/year
aging (Typical)
Table 4: Trigger generator
Characteristics Description
Trigger rate
Range 1.0 μsto10.0s
Resolution 0.1 μsminimum
Accuracy
Same as the reference oscillator
Table 5: Inter-channel skew control
acteristics
Char
w control
Ske
Range
Resolution
Skew accuracy (Typical)
1
Effective skew setting is the absolute value of the difference between the skew setting on channels.
1
ription
Desc
–5 ns to +5 ns
5ps
±(10% of effective skew setting +150 ps)
AWG5000C Series Arbitrary Waveform Generators Technical Reference 3
Specications
Table 6: Wavefo
rm rotation control for analog output
Characteristics Description
Phase control
Range
Resolution
CVR Gain stab
CVR Gain lin
ility is ±0.1% if measured within 25° of the temperature at factory calibration
earity is ±0.2%. Perform an automatic sweep and take voltage measurements
at every DAC value.
Range
l
–1/2 perio
d to +1/2 period of waveform
Time contro
Resolution 1 ps
Point control
Range
Resoluti
on
–50% to +50% of waveform
0.001 poi
nts
Table 7: Analog output
Characteristics Description
Connector type BNC on front panel
Type of output (+) and (–) complementary output
Output impedance 50
Amplitude controls
Range
Normal mode 20 mV to 4.5 V
Direct output mode 20 mV to 0.6 V
Resolution 1 mV
Offset controls
Range
Normal mode –2.25 V to +2.25 V
Direct output mode
N/A
Resolution 1 mV
Amplitude accuracy
Offset accuracy
DC accuracy: within ± (2% of amplitude + 2 mV) at offset = 0V
DC accuracy: within ± (2% of |offset| + 15 mV) at minimum amplitude
Bandwidth (Ty pical)
Normal mode
Direct output mode
250 MHz (at –3 dB), when amplitude = 2.0 V
370 MHz (at –3 dB), when amplitude = 0.6 V
Rise/fall time (Typical)
Normal mode
Direct output mode
1.4 ns (10% to 90%), when amplitude = 2.0 V
0.95 ns (10% to 90%), when amplitude = 0.6 V
Overshoot (Typical) < 10%, when amplitude = 2.0 V
p-p
p-p
,offset=0V
p-p
p-p
,offset=0V
p-p
p-p
p-p
4 AWG5000C Series Arbitrary Waveform Generators Technical Reference
Specications
Table 7: Analog output (cont.)
Characteristics Description
Ringing (Typical)
Normal mode
Direct output mode 65 mV
Low pass lter
Normal mode
Direct output mode
Delay from marker (Typical)
ON/OFF control Output relay is available for each channel. A control is common to the complementary output.
nic distortion
Harmo
012C, AWG5014C
AWG5 Normal mode
AWG5002C, Normal mode < -49 dBc, when amplitude = 0.6 V
AWG5012C, AWG5014C Direct output mode
AWG5002C, Direct output
de
mo
Non-harmonic spurious
AWG5012C, AWG5014C < -60 dBc, DC to 600 MHz, when clock = 1.2 GS/s, signal = 37.5 MHz
AWG5002C < -60 dBc, DC to 300 MHz, when clock = 600 MS/s, signal = 18.75 MHz
SFDR (Typical)
AWG5012C, AWG5014C 50 dBc, when clock = 1.2 GS/s, signal = 37.5 MHz
AWG5002C, AWG5012C, AWG5014C
Normal mode Amplitude = 0.6 V
p-p
850 mV
175 mV
, when amplitude = 4.5 V
p-p
, when amplitude = 2.0 V
p-p
, when amplitude = 0.6 V
p-p
, lter = Through
p-p
, lter = Through
p-p
p-p
20 MHz, 100 MHz, Through (Bessel type)
N/A
Direct output delay +19.0 ns: low pass = 20 MHz
Direct output delay +5.3 ns: low pass = 100 MHz
Direct output delay +1.5 ns: low pass = Through
–1.5 n s to +0.4 ns: direct output mode
(when amplitude = 0.6 V
Measured with 32-point sine waveform, dened up to 5
dBc, when amplitude = 2.0 V
<-40
< -46 dBc, when amplitude = 2.0 V
< -55 dBc, when amplitude = 0.6 V
mplitude = 2.0 V
A
p-p
,offset=0V)
p-p
th
harmonics.
, offset = 0 V, clock = 1.2 GS/s, signal = 37.5 MHz
p-p
, offset = 0 V, clock = 1.2 GS/s, signal = 37.5 MHz
p-p
, offset = 0 V, clock = 600 MS/s, signal = 18.75 MHz
p-p
, offset = 0 V, clock = 600 MS/s, signal = 18.75 MHz
p-p
, offset = 0 V, measured with 32-point sine waveform, measurement range
is DC to sampling_frequency ÷ 2
(Normal output mode, amplitude = 2.0 V
, offset = 0 V, measured with 32-point sine waveform,
p-p
measurement range is DC to sampling_frequency ÷ 2 including harmonics)
56 dBc, when clock = 600 MS/s, signal = 18.75 MHz
(Normal output mode, amplitude = 2.0 V
, offset = 0 V, measured with 32-point sine waveform,
p-p
measurement range is DC to sampling_frequency ÷ 2 including harmonics)
-60 dBc, when signal = 10 MHz
-80 dB c, when signal = 1 MHz
(Clock = 600 MS/s, offset = 0 V, measured with 60 and 600 points/cycle sine waveform, measurement range is DC to 300 MHz)
AWG5000C Series Arbitrary Waveform Generators Technical Reference 5
Specications
Table 7: Analog output (cont.)
Characteristics Description
Direct output mode Amplitude =0.6V
p-p
-64 dBc, when signal = 10 MHz
-80 dBc, when signal = 1 MHz
(Clock = 600 MS/s, offset = 0 V, measured with 60 and 600 points/cycle sine waveform, measurement range is DC to 300 MHz)
Phase noise
Amplitude = 2.0 V
, offset = 0 V, measured with 32-point sine waveform
p-p
AWG5012C, AWG5014C < -85 dBc/Hz at 10 kHz offset, when clock = 1.2 GS/s, signal = 37.5 MHz
AWG5002C < -85 dBc/Hz at 10 kHz offset, when clock = 600 MS/s, signal = 18.75 MHz
Skew between (+) and (-) output
l)
(Typ ica
< 200 ps
Table 8: Marker output
Characteristics Description
Connector type BNC on front panel
Number of outputs Marker 1 and Marker 2 are available for each channel.
Type of output Single-ended output
Output impedance 50
Level controls
Voltage window
Amplitude
Resolution 0.01 V
vel accuracy
Le
utput current
O
Variable delay control
Range 0 to 1000 ps
Resolution 50 ps
Variable delay accuracy
Rise/fall time (Typical) 300 ps (20% to 80% of swing), when Hi = 1.0 V, Low = 0 V
Skew between Marker-1and Marker-2 output (Typical)
Skew between (+) and (–) output (Typ ical)
Random jitter on clock pattern (Typ ical)
Total jitter on random pattern (Typ ical)
Output voltage into RLOAD() to GND is approximately (2 × RLOAD ÷ (50 + RLOAD)) × voltage setting
-1.0Vto+2.7Vinto50
0.1 V
to +3.7 V
p-p
maximum into 50
p-p
DC accuracy: ± (10% of |setting| + 120 mV) into 50
± 54 mA maximum
vailable for Marker 1 and Marker 2
A
± (5% of |setting| + 250 ps)
< 1000 ps
< 100 ps
(by 0101... clock pattern), when H i = 1.0 V, Low = 0 V
5ps
RMS
150 ps
(using PN15 pattern, when High = 1.0 V, Low = 0 V), measured at bit error rate = 1e
p-p
–12
6 AWG5000C Series Arbitrary Waveform Generators Technical Reference
Specications
Table 9: Digita
l data output (Option 03 only)
Characteristics Description
Connector type SMB on rear panel
Number of outputs 28 (14-bit output on channel 1 and channel 2)
Type of output Single-ended
Output impedance 50
Level cont
rols
Output voltage into RLOAD() to GND is approximately (2 × RLOAD ÷ (50 + RLOAD)) × voltage setting
Voltage window
Amplitude
-1.0Vto+2.7Vinto50
0.1 V
to +3.7 V
p-p
into 50
p-p
Resolution 0.01 V
Level ac
Output current
curacy
DC accuracy: ± (10% of |setting| + 120 mV) into 50
±54mAm
aximum
Rise/fall tim e (Typical) 300 ps (20% to 80%, when Hi = 1.0 V, Low = 0 V)
s between 14-bit outputs
Skew between outputs (Typic al)
< 400 p
Table 10: Trigger and gate input
Characteristics Description
Connector type BNC on front panel
Input impedance
Polarity Positive o r negative selectable
Input voltage range
When1kΩ selected
When 50 selected
Threshold control
Level –5.0 V to 5.0 V
Resolution 0.1 V
Accuracy (Typical) ± (5% of |setting| + 0.1 V)
Input voltage swing (Ty pical)
Minimum pulse width
Triggered mode 20 ns
Gated mode
Trigger delay to analog output (Typ ical)
Trigger hold off time (Typical)
Gate delay to analog output (Typ ical)
Trigger jitter (Typ ical)
1kΩ or 50 Ω selectable
-10 V to 10 V
<5V
RMS
minimum
0.5 V
p-p
1024 × sampling period + 10 ns
48 × s ampling period + 500 ns
160 × sampling period – 200 ns
When hardware sequencer is used
240 × sampling period + 500 ns
2.0nsto4.5ns
AWG5000C Series Arbitrary Waveform Generators Technical Reference 7
Specications
Table 11: Event
input
Characteristics Description
Connector type BNC on front panel
Input impeda
Polarity Positive or
nce
1kΩ or 50 Ω selectable
negative selectable
Input voltage range
When 1 kselected
When 50 selected
–10Vto10V
<5V
RMS
Threshold control
Level –5.0 V to 5
.0 V
Resolution 0.1 V
Accuracy (Typical) ± (5% of |setting| + 0.1 V)
minimum
Input voltage swing (Typical)
0.5 V
p-p
Minimum pulse width 20 ns
Delay to analog output (Typical)
200 × s a
mpling period + 500 ns
When asynchronous jump
ampling period + 300 ns
Hold off time (Typical)
260 × s
Table 12: Reference clock input
Characteristics Description
Connector type BNC on rear panel
Input impedance
Input voltage swing 0.2 V
50 (AC coupled)
to3V
p-p
p-p
Fixed mode input frequency 10 MHz, 20 MHz, and 100 MHz within ± 0.5%
Variable mode input frequency range
10 MHz to 600 MHz
Frequency should be stable
Acceptable frequency drift while the instrument is operating: ± 0.5%
Variable mode multiplier rate The rate value is limited by s ampling rate range.
AWG5012C, AWG5014C
AWG5002C
1to240
1to120
8 AWG5000C Series Arbitrary Waveform Generators Technical Reference
Specications
Table 13: Oscil
lator (External clock) input
Characteristics Description
Connector type BNC on rear panel
Input impeda
Frequency r
nce
ange
50 (AC coupled)
600 MHz to 12
00 MHz
Frequency should be stable.
Acceptable frequency drift while running is ±0.5%.
Input voltage swing 0.2 V to 0.8 V
p-p
Divider
AWG5012C
, AWG5014C
1/1, 1/2,
AWG5002C 1/2, 1/4,
1/4, 1/8, ... ,1/32
1/8, ... ,1/32
Table 14: Add input
Characteristics Description
Connector type BNC on the rear panel, for each channel
Input impedance
DC gain (Typical)
Bandwidth (Ty pical) DC to 100 MHz, at –3 dB, when amplitude is 1 V
Input voltage range ± 1.0 V
50 (DC coupled)
1
p-p
Table 15: DC output
Characteristics Description
Connector type 2 x 4 pin header, 2.54 mm pitch (female) on front panel
Number of outputs
4
Output voltage control
Range –3.0 V to +5.0 V
Resolution 10 mV
Control Independent for each output
Output voltage accuracy
Output current
± (3% of |setting| + 120 mV) into High-Z load
±100 mA maximum
Output impedance (Typical)1
Table 16: Oscillator output
Characteristics Description
Connector type BNC on rear panel
Output impedance 50 (AC coupled)
Output frequency range
Output voltage swing ( Ty pical)0.4V
600 MHz to 1200 MHz
into 50
p-p
AWG5000C Series Arbitrary Waveform Generators Technical Reference 9
Specications
Table 17: Dynam
Characteristics Description
Function
Connector type 9-pin D-sub female to converter box (Tektronix part number, 850-0108-xx) through the TekLink
Input signal & pin assignment
Pin
1
2 Event bit
3 Event bit 2, input
4 Event bit 1, input
5
6
7
8
9
Input levels TTL
Input voltage range 0 V to +5 V
-level input voltage
High
Low-level input voltage 0 V to +0.8 V
Input impedance
Output connector type
Output levels LVDS
Strobe Must Strobe jump destination
Number of dynamic jump destinations
Minimum strobe width 64 ns
Latency to Analog Output (Typical) From D-sub connector on TTL-to-LVDS converter to Analog output when asynchronous jump
Hold-off time (Ty pical) Maximum of 500 sample clock cycles
ic Jump In for Option 09 Only
Allows fast switching during table jump and subsequence
connector
Signal and direction
Strobe, input
3, input
Event bi
GND
GND
GND
GND
2Vto
Pull up to 4.5 V by 2.2 kresistor
40-pin TekLink connector with TekLink cable
16 Maximum sequence indices
The ag that decides whether or not the event input pattern is valid can be set to each of the patterns.
is selected
Maximum 650 ns at 1.2 GS/s
Maximum 1300 ns at 650 MS/s
When asynchronous jump is selected
t 0, input
5V
10 AWG5000C Series Arbitrary Waveform Generators Technical Reference
Specications
Table 18: 10 MHz
clock output
Characteristics Description
Connector type BNC on rear panel
Output impedance 50 (AC coupled)
Amplitude (Typical)1.2V
2.4 V
into 50
p-p
into 1 M
p-p
Table 19: TekLink port
Characteristics Description
Function
Provides a TekLink interface that complies with Tektronix TekLink 2.0 specication
The instrument operates in slave mode only.
Connector type
40-pin connector on rear panel
Table 20: CPU module and peripheral devices
Characteristics Description
CPU
Memory
Hard disk drive
Optical disk drive CD-RW/DVD drive, writing software not included
USB 2.0 6 (2 x front, 4 x rear)
LAN
ESATA External ESATA at 1.5Gbps
Video output
GPIB IEEE 488.2 standard interface, 24 pins
PS2 keyboard connector
PS2 mouse connector
Serial ports Two R S-232C, D-sub, 9 pins
Intel core duo processor
4 GB DDR2-800 or faster
160 GB, usable area is about 90%
RJ-45 LAN connector supporting 10 base-T, 100 base-T, and Gigabit Ethernet on rear panel
DV/I connector
6pins,mini-DIN
6pins,mini-DIN
Table 21: Display
Characteristics Description
Size 210mmX158mm(8.28inX6.22in)
Resolution 1024 X 768 pixels
Touch screen Built-in touch screen
AWG5000C Series Arbitrary Waveform Generators Technical Reference 11
Specications
ge
supply
AC
to 240
AC
100 V
The maximum power consumed by the fully-optioned instrument
V
Table 22: Power
Characteristics Description
Source voltage and frequency
Rating volta
Frequency range 47 Hz to 63 Hz
Power consumption 560 W
Surge current 30 A peak (25 °C) for 5 line cycles, after product has been turned off for at least 30 s.
Mechanical (Physical) Characteristics
Table 23:
Characteristics Description
Net weight (Typical)
Dimens
Dimensions, with packaging
Cooling method Forced-air circulation with no air lter
Clearance
Mechanical characteristics
package
Without
ckage
With pa
ions, overall
Height
Width
Length
Height
Width
Length
Top and bottom
Bottom
Left side 150 mm (6 in)
Right side
Rear
Approximately 19.5 kg (42.9 lb)
Approximately 28.5 kg (62.8 lb)
245 mm
465 mm
500 m
635 mm (25 in)
665 mm (26.2 in)
500 mm (19.7 in)
20 mm (0.8 in)
20 mm (0.8 in)
150 mm (6 in)
75 mm (3.0 in)
(9.6 in)
(18.3 in)
m (19.7 in)
12 AWG5000C Series Arbitrary Waveform Generators Technical Reference
Specications
Environmenta
l Characteristics
Table 24: Environmental characteristics
Characteris
Temperature
Relative h
Altitude
tics
Operating +10 °C to +40 °C (+50 °F to 104 °F) with 15 °C/hour (59 °F/hour) maximum gradient,
Nonoperating
umidity
Operatin
Nonoperating
Operating Up to 3,000 m (approximately 10,000 feet)
Nonop
g
erating
Description
noncondens
–20 °C to +6 no media installed in disc drives
5% to 90% r
5% to 45% relative humidity above +30 °C (+86 °F) up to +40 °C (104 °F) noncondensing, and as limited by a maximum wet-bulb temperature +29 °C (84.2 °F) (derates relative humidity to 45% rel
5% to 90%
5% to 45% relative humidity above +30 °C (+86 °F) up to +40 °C (104 °F) noncondensing, and as limited by a maximum wet-bulb temperature +29 °C (84.2 °F) (derates relative humidity to 11% r
Maxim km (4921 ft)
Up to 12,000 m (approximately 40,000 feet)
ing derated 1.0 °C (34 °F) per 300 m (984 ft) above 1500 m (4921 ft) altitude
0 °C (-4 °F to 140 °F) with 30 °C/hour (86 °F/hour) maximum gradient, with
elative humidity at up to +30 °C (+86 °F)
ative humidity at +40 °C (104 °F))
relative hum idity at up to +30 °C (+ 86 °F)
elative humidity at +40 °C (104 °F))
um operating temperature decreases 1 °C (34 °F) each 300 m (984 ft) above 1.5
AWG5000C Series Arbitrary Waveform Generators Technical Reference 13
Specications
14 AWG5000C Series Arbitrary Waveform Generators Technical Reference
Performance Verication Procedures
Two types of performance verication procedures can be performed on the instrument: Brief Procedures and Performance Tests. You may not need to perform all o
To rapidly conrm that the instrument functions and was adjusted properly, perform Diagnostics and Self Calibration.
Advantages: These procedures are quick to do and require no external equipment or signal sources. These procedures perform extensive functional and accuracy testing to provide high condence that the instrument will perform properly.
f these procedures, depending on what you want to accomplish.
Brief Procedures
To further check functionality, rst perform Diagnostics and Self Calibr and then perform Functional Test.
Advantages: The procedure requires minimal additional time to perform, and requires minimal equipment. The procedure can be used when the instrument is rst rec eived.
If more extensive conrmation of performance is desired, complete the self tests and functional test, and then do the Performance Tests.
Advantages: These proced ures add direct checking o f warranted specications. These procedures require specic test equipment. (See page 23, Required Equipment.)
If you are not familiar with operating this instrument, refer to the online help or the user information supplied with the instrument.
There are three procedures in this section that provide a quick way to conrm basic functionality and proper adjustment:
Diagnostics
ation,
Self Calibration
Functional Test
Diagnostics
The following steps run the internal routines that conrm basic functionality and proper adjustment.
Equipment Prerequisites
None None
AWG5000C Series Arbitrary Waveform Generators Technical Reference 15
Brief Procedures
1. Disconnect all
2. Select System > Diagnostics.
Figure 1: Diagnostics dialog box
the cables from the output channels.
3. In the Diagnostics dialog box, conrm that all the check boxes are selected. If they ar
4. Click the Execute button to execute the diagnostics.
The internal diagnostics perform an exhaustive verication of proper instrument function. This verication may take several minutes. When the veri
5. Verify that Pass appears as Status in the dialog box when the diagnostics com
6. Click the Close button.
e not all selected, click the Select All button.
cation is completed, the resulting status will appear in the dialog box.
plete.
16 AWG5000C Series Arbitrary Waveform Generators Technical Reference
Brief Procedures
Self Calibrat
ion
Equipment Prerequisites
None Power on the instrument and allow a
20 minute warm-up before doing this procedure.
1. Select System > Calibration.
Figure 2: Calibration dialog box
2. Click the Execute button to start the routine.
3. Verify that Pass appears in the status column for all items when the calibration
completes.
4. Click the Close button.
Functional Test
Checking the Analog and
Marker Outputs
The purpose of the procedure is to conrm that the instrument functions properly. The required equipment is three 50 BNC cables, an oscilloscope, and a 50 SMB-BNC cable (Option 03 only).
Required equipment Prerequisites
Oscilloscope (DPO7054 or equivalent)
Three 50 BNC cables
1. Press the All Outputs On/Off button on the instrument to turn off all the outputs.
2. Use a 50 BNC cable to connect the Channel 1 Analog connector on the instrument to the CH1 connector on the oscilloscope.
3. Use a 50 BNC cable to connect the Channel 1 Mkr 1 connector on the instrument to the CH2 connector on the oscilloscope.
4. Use the 50 BNC cable to connect the Channel 1 Mkr 2 connector on the instrument to the CH3 connector on the oscilloscope.
None
AWG5000C Series Arbitrary Waveform Generators Technical Reference 17
Brief Procedures
Figure 3: Equipment connections for checking the analog and marker outputs
5. Set the oscilloscope as follows:
a. Vertica
b. Horizontal scale: 200 ns/div
c. Input coupling: DC
d. Input impedance: 50
e. CH 1 position: +2 div (if necessary)
f. CH 2 position: –1 div (if necessary)
g. CH 3 p
h. Trigger source: CH1
i. Trigger level: 0 mV
j. Trigger slope: Positive
k. Trigger mode: Auto
6. Press the Factory Default button on the instrument.
ress the Ch1 Select button on the instrument.
7.P
l scale: 1 V/div (CH1, CH2, and CH3)
osition: –3 div (if necessary)
18 AWG5000C Series Arbitrary Waveform Generators Technical Reference
Brief Procedures
8. On the instrume
a. Select File > Open File.
b. In the dialog box, navigate to the C:\Program
Files\Tektronix\AWG\System\PV directory, and then select the pv_awg5
c. In the window, select (drag and drop) the sine_mk1_mk2 waveform on
the User De
NOTE. If your instrument is an AWG5002C a warning message is displayed when
you open the pv_awg5000.awg le. Ignore the message and press the OK button.
9. Press the Ch 1 On button on the instrument to enable the channel 1 output.
10. Press th
11. Check that the Channel 1 Analog, Mkr 1, and Mkr 2 waveforms are properly
displa
e Run button on the instrument to output the waveform.
yed on the oscilloscope screen.
nt, load the sine_mk1_mk2 waveform as an output waveform.
000.awg le. The Waveform List window appears.
ned tab.
Figure 4: Output waveform from the Analog, Mkr 1, and Mkr 2 outputs
12. Press the Ch 1 On button again to disable the channel 1 output.
13. Repeat the test for the Channel 2 Analog, Mkr 1, and Mkr 2 outputs.
14. For the AWG5014C Repeat the test for the Channel 3 and Channel 4 Analog,
Mkr 1, and Mkr 2 outputs.
AWG5000C Series Arbitrary Waveform Generators Technical Reference 19
Brief Procedures
Checking the D
igital Data
Outputs (Option 03 Only)
Required equipment Prerequisites
Oscilloscope (DPO7054 or equivalent)
50 BNC cable
50 SMB-BNC cable (Tektronix part number 174-5104-00)
None
1. Press the All Outputs On/Off button on the instrument to turn off all the outputs.
2. Use the 50 SMB-BNC cable and 50 BNC cable to connect the Ch 1 Digital Data Out 0 connector on the instrument rear panel to the CH1 connector on the oscilloscope.
Figure 5: Equipment connection for checking the digital data outputs
3. Set the oscilloscope as follows:
a. Vertical scale: 500 mV/div
b. Horizontal scale: 200 ns/div
c. Input coupling: DC
d. Input impedance: 50
e. Trigger source: CH1
f. Trigger level: 500 mV
g. Trigger slope: Positive
h. Trigger mode: Auto
4. Press the Factory Default button on the instrument.
5. Press the Ch1 Select button on the instrument.
20 AWG5000C Series Arbitrary Waveform Generators Technical Reference
Brief Procedures
6. On the instrume
a. Select File > Open File.
b. In the dialog box, navigate to the C:\Program
Files\Tektronix\AWG\System\PV directory, and then select the pv_awg5
c. In the window, select (drag and drop) the square1 waveform on the User
Dened tab.
7. Press the Ch 1 On button on the instrument to enable the channel 1 output.
8. Press the Run button on the instrument to output the waveform.
9. Check that the square wave is properly displayed on the oscilloscope screen.
(See Figure 6.)
NOTE. If your instrument has rmware version 2.0 or earlier, the amplitude of the
yed waveform is different from the waveform shown in the following gure.
displa
nt, load the square1 waveform as an output waveform.
000.awg le. The Waveform List window appears.
Figure 6: Output waveform from the Digital Data Out connector
10. Move the SMB-BNC cable from the Ch 1 Digital Data Out 0 connector to the Ch 1 Digital Data Out 1 connector and repeat the previous step.
11. Repeat step 10 for the remaining digital data outputs (Ch 1 Digital Data Out 2 to Ch 1 Digital Data Out 13).
12. Press the Ch 1 On button again to disable the channel 1 output.
13. Repeat the test for all the Ch 2 Digital Data outputs.
AWG5000C Series Arbitrary Waveform Generators Technical Reference 21
Performance Tests
Performance T
Prerequisites
ests
This section marked with the
The tests in this section comprise an extensive, valid conrmation of performance and functionality when the following requirements are met:
The cabinet must be installed on the instrument.
You must h Calibration, and the procedure Functional Tests.
The inst between +20 °C and +30 °C, must have been operating for a warm-up period of at least 20 minutes, and must be operating at an ambient temperatures between +10 °C and +40 °C.
contains performance verication procedures for the specications
symbol.
ave performed and passed the procedure Diagnostics and Self
rument must have been last adjusted at an ambient temperature
22 AWG5000C Series Arbitrary Waveform Generators Technical Reference
Performance Tests
Required Equipment
The following table lists the test equipme nt required to perform all of the performance verication procedure. The table identies examples of recommended equipment and lists the required precision where applicable. If you substitute other test equipment for the listed examples, the equipment must meet or exce
Table 25: Required equipment
Item Qty. Minimum requirements Recommended equipment
Oscilloscope
Frequency counter 1 ea. Frequency accuracy: within ± 0.01 ppm Agilent Technologies 53181A
Sampling oscilloscope
Spectrum analyzer
Digital multimeter 1 ea.
50 BNC cable
50 BNC termination
BNC-SMA adapter
BNC-N adapter
BNC-dual banana adapter
DC output lead set
1 ea. Bandwidth: 500 MHz or higher
4 channels
1 ea.
1 ea.
2 ea.
1 ea.
2 ea.
1 ea.
1 ea.
1 ea. 8-pin twisted pair, 24 inch Tektronix part number 012-1697-00
Bandwidth: 20 GHz or higher 2 channels
Bandwidth: DC to 8 GHz Tektronix RSA3308B
DC accuracy: within ± 0.01%
DCto2GHz
DC to 1 GHz, feedthrough
BNC female to SMA male connectors
BNC female to N male connectors
BNC to dual banana plugs
ed the listed tolerances.
Tektronix DPO7054
Tektronix CSA8200 with 80E03
Keithley 2000 DMM or Agilent Technologies 34410A
Tektronix part number 012-0057-01
Tektronix part number 011-0049-02
Tektronix part number 015-0554-00
Tektronix part number 103-0045-00
Tektronix part number 103-0090-00
(supplied with the AWG)
AWG5000C Series Arbitrary Waveform Generators Technical Reference 23
Performance Tests
Test Waveforms
The following t
able lists the test waveforms that are used for the performance verication procedures and functional test. These are included in the pv_awg5000.awg le on the C: drive.
Table 26: Test waveforms
No. Waveform name Purpose
1 dc_minus For checking the analog amplitude accuracy
2 dc_plus For checking the analog amplitude accuracy
3dc_zero
4 marker_hi For checking the marker high level accuracy
5
6 sine32 For checking analog harmonic distortion, analog
7
8 square1 For checking the marker output delay accuracy test
marker_low For checking the marker low level accuracy
sine_mk1_mk2
For checking the analog offset accuracy
non-harmonic spurious signal, and analog phase noise
For the functional test
NOTE. If your instrument is an AWG5002C, a warning message is displayed when
you open the pv_awg5000.awg le. Ignore the message and press the OK button.
24 AWG5000C Series Arbitrary Waveform Generators Technical Reference
Te st Record
Photocopy this page and the next eight pages, and use them to record the performance test results for your instrument.
AWG5000C performance test record
Instrument Model:
Instrument Serial Number: Certicate Number:
Temperature:
Date of Calibration:
Performance Test
10 MHz Reference Frequency Accuracy
Analog Offset Accuracy
Ch 1
/Ch 1
Ch 2
Offset Output mode
+2.25 V
+1 V
0.0 V
–1 V
–2.25 V
N/A (0V) Direct D/A out: On
Offset Output mode
+2.25 V
+1 V
0.0 V
–1 V
–2.25 V
N/A (0V) Direct D/A out: On
Offset Output mode
+2.25 V
+1 V
0.0 V
–1 V
–2.25 V
N/A (0V) Direct D/A out: On
Direct D/A out: O ff
Direct D/A out: O ff
Direct D/A out: O ff
Direct D/A out: O ff
Direct D/A out: O ff
Direct D/A out: O ff
Direct D/A out: O ff
Direct D/A out: O ff
Direct D/A out: O ff
Direct D/A out: O ff
Direct D/A out: O ff
Direct D/A out: O ff
Direct D/A out: O ff
Direct D/A out: O ff
Direct D/A out: O ff
RH %:
Technician:
Minimum Incoming
9.99998 MHz 10.00002 MHz
2190 mV 2310 mV
965 mV 1035 mV
–15 mV +15 mV
–1035 mV –965 mV
–2310 mV –2190 mV
–15 mV +15 mV
2190 mV 2310 mV
965 mV 1035 mV
–15 mV +15 mV
–1035 mV –965 mV
–2310 mV –2190 mV
–15 mV +15 mV
2190 mV 2310 mV
965 mV 1035 mV
–15 mV +15 mV
–1035 mV –965 mV
–2310 mV –2190 mV
–15 mV +15 mV
Outgoing
Performance Tests
Maximum
AWG5000C Series Arbitrary Waveform Generators Technical Reference 25
Performance Tests
AWG5000C performance test record (cont.)
Performance Test
/Ch 2
Ch 3
/Ch 3
Ch 4
/Ch 4
Offset Output mode
+2.25 V
+1 V
0.0 V
–1 V
–2.25 V
N/A (0V) Direct D/A out: On
Offset Output mode
+2.25 V
+1 V
0.0 V
–1 V
–2.25 V
N/A (0V) Direct D/A out: On
Offset Output mode
+2.25 V
+1 V
0.0 V
–1 V
–2.25 V
N/A (0V) Direct D/A out: On
Offset Output mode
+2.25 V
+1 V
0.0 V
–1 V
–2.25 V
N/A (0V) Direct D/A out: On
Offset Output mode
+2.25 V
+1 V
0.0 V
–1 V
–2.25 V
N/A (0V) Direct D/A out: On
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Minimum Incoming
2190 mV 2310 mV
965 mV 1035 mV
–15 mV +15 mV
–1035 mV –965 mV
–2310 mV –2190 mV
–15 mV +15 mV
2190 mV 2310 mV
965 mV 1035 mV
–15 mV +15 mV
–1035 mV –965 mV
–2310 mV –2190 mV
–15 mV +15 mV
2190 mV 2310 mV
965 mV 1035 mV
–15 mV +15 mV
–1035 mV –965 mV
–2310 mV –2190 mV
–15 mV +15 mV
2190 mV 2310 mV
965 mV 1035 mV
–15 mV +15 mV
–1035 mV –965 mV
–2310 mV –2190 mV
–15 mV +15 mV
2190 mV 2310 mV
965 mV 1035 mV
–15 mV +15 mV
–1035 mV –965 mV
–2310 mV –2190 mV
–15 mV +15 mV
Outgoing
Maximum
26 AWG5000C Series Arbitrary Waveform Generators Technical Reference
AWG5000C performance test record (cont.)
Performance Tests
Performance Test
Analog Amplitude Accuracy
Ch1
Amplitude
20 mV
200 mV
500 mV
1.0 V
p-p
2.0 V
p-p
4.5 V
p-p
20 mV
200 mV
600 mV
/Ch1
Amplitude
20 mV
200 mV
500 mV
1.0 V
p-p
2.0 V
p-p
4.5 V
p-p
20 mV
200 mV
600 mV
Ch2
Amplitude
20 mV
200 mV
500 mV
1.0 V
p-p
2.0 V
p-p
4.5 V
p-p
20 mV
200 mV
600 mV
Minimum Incoming
Outgoing
Maximum
Output mode
p-p
p-p
p-p
Direct D/A out: O ff
Direct D/A out: O ff
Direct D/A out: O ff
Direct D/A/out: Off
Direct D/A/out: Off
Direct D/A/out: Off
p-p
p-p
p-p
Direct D/A out: On
Direct D/A out: On
Direct D/A out: On
17.6 mV 22.4 mV
194 mV 206 mV
488 mV 512 mV
0.978 V 1.022 V
1.958 V 2.042 V
4.408 V 4.592 V
17.6 mV 22.4 mV
194 mV 206 mV
586 mV 614 mV
Output mode
p-p
p-p
p-p
Direct D/A out: O ff
Direct D/A out: O ff
Direct D/A out: O ff
Direct D/A/out: Off
Direct D/A/out: Off
Direct D/A/out: Off
p-p
p-p
p-p
Direct D/A out: On
Direct D/A out: On
Direct D/A out: On
17.6 mV 22.4 mV
194 mV 206 mV
488 mV 512 mV
0.978 V 1.022 V
1.958 V 2.042 V
4.408 V 4.592 V
17.6 mV 22.4 mV
194 mV 206 mV
586 mV 614 mV
Output mode
p-p
p-p
p-p
Direct D/A out: O ff
Direct D/A out: O ff
Direct D/A out: O ff
Direct D/A/out: Off
Direct D/A/out: Off
Direct D/A/out: Off
p-p
p-p
p-p
Direct D/A out: On
Direct D/A out: On
Direct D/A out: On
17.6 mV 22.4 mV
194 mV 206 mV
488 mV 512 mV
0.978 V 1.022 V
1.958 V 2.042 V
4.408 V 4.592 V
17.6 mV 22.4 mV
194 mV 206 mV
586 mV 614 mV
AWG5000C Series Arbitrary Waveform Generators Technical Reference 27
Performance Tests
AWG5000C performance test record (cont.)
Performance Test
/Ch2
Ch3
/Ch3
Amplitude
20 mV
p-p
200 mV
500 mV
1.0 V
p-p
2.0 V
p-p
4.5 V
p-p
20 mV
p-p
200 mV
600 mV
Amplitude
20 mV
p-p
200 mV
500 mV
1.0 V
p-p
2.0 V
p-p
4.5 V
p-p
20 mV
p-p
200 mV
600 mV
Amplitude
20 mV
p-p
200 mV
500 mV
1.0 V
p-p
2.0 V
p-p
4.5 V
p-p
20 mV
p-p
200 mV
600 mV
Minimum Incoming
Outgoing
Maximum
Output mode
Direct D/A out: Off
p-p
p-p
Direct D/A out: Off
Direct D/A out: Off
Direct D/A/out: Off
Direct D/A/out: Off
Direct D/A/out: Off
Direct D/A out: On
p-p
p-p
Direct D/A out: On
Direct D/A out: On
17.6 mV 22.4 mV
194 mV 206 mV
488 mV 512 mV
0.978 V 1.022 V
1.958 V 2.042 V
4.408 V 4.592 V
17.6 mV 22.4 mV
194 mV 206 mV
586 mV 614 mV
Output mode
Direct D/A out: Off
p-p
p-p
Direct D/A out: Off
Direct D/A out: Off
Direct D/A/out: Off
Direct D/A/out: Off
Direct D/A/out: Off
Direct D/A out: On
p-p
p-p
Direct D/A out: On
Direct D/A out: On
17.6 mV 22.4 mV
194 mV 206 mV
488 mV 512 mV
0.978 V 1.022 V
1.958 V 2.042 V
4.408 V 4.592 V
17.6 mV 22.4 mV
194 mV 206 mV
586 mV 614 mV
Output mode
Direct D/A out: Off
p-p
p-p
Direct D/A out: Off
Direct D/A out: Off
Direct D/A/out: Off
Direct D/A/out: Off
Direct D/A/out: Off
Direct D/A out: On
p-p
p-p
Direct D/A out: On
Direct D/A out: On
17.6 mV 22.4 mV
194 mV 206 mV
488 mV 512 mV
0.978 V 1.022 V
1.958 V 2.042 V
4.408 V 4.592 V
17.6 mV 22.4 mV
194 mV 206 mV
586 mV 614 mV
28 AWG5000C Series Arbitrary Waveform Generators Technical Reference
AWG5000C performance test record (cont.)
Performance Tests
Performance Test
Ch4
/Ch4
Amplitude
20 mV
p-p
200 mV
p-p
500 mV
p-p
1.0 V
p-p
2.0 V
p-p
4.5 V
p-p
20 mV
p-p
200 mV
p-p
600 mV
p-p
Amplitude
20 mV
p-p
200 mV
p-p
500 mV
p-p
1.0 V
p-p
2.0 V
p-p
4.5 V
p-p
20 mV
p-p
200 mV
p-p
600 mV
p-p
Output mode
Direct D/A out: O ff
Direct D/A out: O ff
Direct D/A out: O ff
Direct D/A out: O ff
Direct D/A out: O ff
Direct D/A out: O ff
Direct D/A out: On
Direct D/A out: On
Direct D/A out: On
Output mode
Direct D/A out: O ff
Direct D/A out: O ff
Direct D/A out: O ff
Direct D/A out: O ff
Direct D/A out: O ff
Direct D/A out: O ff
Direct D/A out: On
Direct D/A out: On
Direct D/A out: On
Analog Harmonic Distortion (AWG501xC)
Ch 1
Ch 2
Ch 3
Ch 4
Amplitude
2.0 V
0.6 V
Amplitude
2.0 V
0.6 V
Amplitude
2.0 V
0.6 V
Amplitude
2.0 V
0.6 V
Output mode
Direct D/A out: O ff
Direct D/A out: On
Output mode
Direct D/A out: O ff
Direct D/A out: On
Output mode
Direct D/A out: O ff
Direct D/A out: On
Output mode
Direct D/A out: O ff
Direct D/A out: On
Minimum Incoming
Outgoing
Maximum
17.6 mV 22.4 mV
194 mV 206 mV
488 mV 512 mV
0.978 V 1.022 V
1.958 V 2.042 V
4.408 V 4.592 V
17.6 mV 22.4 mV
194 mV 206 mV
586 mV 614 mV
17.6 mV 22.4 mV
194 mV 206 mV
488 mV 512 mV
0.978 V 1.022 V
1.958 V 2.042 V
4.408 V 4.592 V
17.6 mV 22.4 mV
194 mV 206 mV
586 mV 614 mV
none
none
none
none
none
none
none
none
–40 dBc
–49 dBc
–40 dBc
–49 dBc
–40 dBc
–49 dBc
–40 dBc
–49 dBc
AWG5000C Series Arbitrary Waveform Generators Technical Reference 29
Performance Tests
AWG5000C performance test record (cont.)
Performance Test
Analog Harmonic Distortion (AWG5002C)
Ch 1
Ch 2
Ch 3
Ch 4
Analog Non-Harmonic Spurious
Ch1
Ch 2
Ch 3
Ch 4
Analog P hase Noise (at 10 kHz offset)
Ch 1
Ch 2
Ch 3
Ch 4
Amplitude
2.0 V
0.6 V
Amplitude
2.0 V
0.6 V
Amplitude
2.0 V
0.6 V
Amplitude
2.0 V
0.6 V
Amplitude
2.0 V
Amplitude
2.0 V
Amplitude
2.0 V
Amplitude
2.0 V
Amplitude
2.0 V
Amplitude
2.0 V
Amplitude
2.0 V
Amplitude
2.0 V
Output mode
Direct D/A out: Off
Direct D/A out: On
Output mode
Direct D/A out: Off
Direct D/A out: On
Output mode
Direct D/A out: Off
Direct D/A out: On
Output mode
Direct D/A out: Off
Direct D/A out: On
Output mode
Direct D/A out: Off
Output mode
Direct D/A out: Off
Output mode
Direct D/A out: Off
Output mode
Direct D/A out: Off
Output mode
Direct D/A out: Off
Output mode
Direct D/A out: Off
Output mode
Direct D/A out: Off
Output mode
Direct D/A out: Off
Minimum Incoming
none
none
none
none
none
none
none
none
none
none
none
none
none
none
none
none
Outgoing
Maximum
–46 dBc
–55 dBc
–46 dBc
–55 dBc
–46 dBc
–55 dBc
–46 dBc
–55 dBc
–60 dBc
–60 dBc
–60 dBc
–60 dBc
–85 dBc/Hz
–85 dBc/Hz
–85 dBc/Hz
–85 dBc/Hz
30 AWG5000C Series Arbitrary Waveform Generators Technical Reference
AWG5000C performance test record (cont.)
Performance Tests
Performance Test
Marker High and Low Level Accuracy
Ch 1
Ch 1
Ch 2
Mkr 1 High level setting
Mkr 2 High level setting
Mkr 1 High level setting
Minimum Incoming
+2.7 V 2.31 V 3.09 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–0.9 V –1.11 V –0.69 V
Low level setting
+2.6 V 2.22 V 2.98 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–1.0 V –1220 mV –780 mV
+2.7 V 2.31 V 3.09 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–0.9 V –1.11 V –0.69 V
Low level setting
+2.6 V 2.22 V 2.98 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–1.0 V –1220 mV –780 mV
+2.7 V 2.31 V 3.09 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–0.9 V –1.11 V –0.69 V
Low level setting
+2.6 V 2.22 V 2.98 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–1.0 V –1220 mV –780 mV
Outgoing
Maximum
AWG5000C Series Arbitrary Waveform Generators Technical Reference 31
Performance Tests
AWG5000C performance test record (cont.)
Performance Test
Ch 2
Ch 3
Ch 3
Ch 4
Mkr 2 High level setting
+2.7 V 2.31 V 3.09 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–0.9 V –1.11 V –0.69 V
Low level setting
+2.6 V 2.22 V 2.98 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–1.0 V –1220 mV –780 mV
Mkr 1 High level setting
+2.7 V 2.31 V 3.09 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–0.9 V –1.11 V –0.69 V
Low level setting
+2.6 V 2.22 V 2.98 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–1.0 V –1220 mV –780 mV
Mkr 2 High level setting
+2.7 V 2.31 V 3.09 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–0.9 V –1.11 V –0.69 V
Low level setting
+2.6 V 2.22 V 2.98 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–1.0 V –1220 mV –780 mV
Mkr 1 High level setting
+2.7 V 2.31 V 3.09 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–0.9 V –1.11 V –0.69 V
Minimum Incoming
Outgoing
Maximum
32 AWG5000C Series Arbitrary Waveform Generators Technical Reference
AWG5000C performance test record (cont.)
Performance Tests
Performance Test
Ch 4
Ch 4
Marker Output Delay Accuracy
Ch 1
Ch 2
Ch 3
Ch 4
DC Output Accuracy
DC output
+5 V 4.73 V 5.27 V
+3 V 2.79 V 3.21 V
0.0 V –120 mV +120 mV
–3 V –3.21 V –2.79 V
Mkr 2 High level setting
Mkr 1 700 ps 1300 ps
Mkr 2 700 ps 1300 ps
Mkr 1 700 ps 1300 ps
Mkr 2 700 ps 1300 ps
Mkr 1 700 ps 1300 ps
Mkr 2 700 ps 1300 ps
Mkr 1 700 ps 1300 ps
Mkr 2 700 ps 1300 ps
Low level setting
+2.6 V 2.22 V 2.98 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–1.0 V –1220 mV –780 mV
+2.7 V 2.31 V 3.09 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–0.9 V –1.11 V –0.69 V
Low level setting
+2.6 V 2.22 V 2.98 V
+1.0 V 780 mV 1220 mV
0.0 V –120 mV +120 mV
–1.0 V –1220 mV –780 mV
Minimum Incoming
Outgoing
Maximum
AWG5000C Series Arbitrary Waveform Generators Technical Reference 33
Performance Tests
10 MHz Referen
Figure 7: Equipment connection for verifying the 10 MHz reference frequency accuracy
ce Frequency Accuracy
Required equipment Prerequisites
Frequency counter
50 BNC cable
1. Use the 50 BNC cable to connect the 10 MHz Reference Output connector
on the instrument to the frequency counter CH1 input.
(See page 22, Prerequisites.)
Analog Offset Accuracy
2. Set the frequency counter as follows:
a. MEASURE: Frequency1, Gate Time: 0.10 s
b. CHANNEL1: Coupling: AC, Impedance: 50
3. Press the Factory Default button on the instrument.
4. Veri
5. Dis
Required equipment Prerequisites
Digital multim e ter
50 BNC cable
50 BNC termination
BNC-dual banana adapter
fy that the frequency counter reading falls within the range of
9.99998 MHz to 10.00002 MHz (± 2 ppm).
connect the test setup.
(See page 22, Prerequisites.)
34 AWG5000C Series Arbitrary Waveform Generators Technical Reference
Performance Tests
Measuring the Termination
Resistance
Before verifyi of the 50BNC termination.
1. Connect the BN and LO inputs on the digital multimeter.
Figure 8: Equipment connection for measuring the termination resistance
2. Set the digital multimeter to the W2wiresmode.
3. Measure the resistance and note the value as Te r m _R.
4. Set the d
5. Disconnect the test setup.
NOTE. L
four wire ohms. The accuracy is higher especially for small resistances. Use a four wire method if necessary.
ng the analog offset accuracy, you need to measure the resistance
C-dual banana adapter and 50 BNCterminationtotheHI
igital multimeter to the VDC mode.
ead resistance is not included in the measurement results when using
Verifying the Analog Offset
Accuracy
1. Press the All Outputs On/Off button on the instrument to turn off all the outputs.
2. Use the 50 BNC cable, 50 BNC termination, and BNC-dual banana adapter to connect the Channel 1 Analog connector on the instrument to the HI and LO inputs on the digital multimeter.
AWG5000C Series Arbitrary Waveform Generators Technical Reference 35
Performance Tests
Figure 9: E
quipment connection for verifying the analog offset accuracy
3. Press the
Factory Default button on the instrument.
4. Press the Ch1 Select button on the instrument.
5. On the instrument, load the dc_zero waveform as an output waveform.
a. Select File > Open File.
b. In the dialog box, navigate to the C:\Program
Files\Tektronix\AWG\System\PV directory, and then select the pv_awg5000.awg le. The Waveform List window appears.
c. In the window, select (drag and drop) the dc_zero waveform on the User
Dened tab.
6. Press the Ch 1 On button on the instrument to enable the channel 1 output.
7. Press the Run button on the instruemnt to output the waveform.
8. Set the offset of the instrument to the level shown in the rst row of the
following table:
Table 27: Analog offset accuracy
Offset settings Output mode settings Accuracy limits
+2.25 V
1V
0.0 V
–1 V
–2.25 V
N/A (0 V) Direct D/A out: On
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
2190 mV to 2310 mV
965 mV to 1035 mV
–15 mV to +15 mV
–1035 mV to –965 mV
–2310 mV to –2190 mV
–15 mV to + 15 mV
36 AWG5000C Series Arbitrary Waveform Generators Technical Reference
Performance Tests
9. Measure the out Measured_voltage.
10. Use the follow
termination:
Voltage = [(
Where Term_R is the resistance of the 50 BNC termination measured in step 3. (See
11. Verify that the calculated value falls within the limits given in the table. (See Table
12. Repeat steps 8 through 11 for each offset setting in the table. (See Table 27.)
13. Move the BNC termination from the Channel 1 Analog connector to the
Channel 1 A
14. Repeat steps 8 through 12.
15. Repeat steps 6 through 14 for the Channel 2 output.
16. For the AWG5014C: Repeat the test for the Channel 3 and Channel 4 outputs.
17. Press the All Outputs On/Off button on the instrument to turn off all the
outputs.
put voltage on the digital multimeter and note the value as
ing formula to compensate the voltage for the 50 BNC
Term_R + 50) /(2 × Term_R)] × Measured_voltage
page 35, Measuring the Termination Resistance.)
27.)
nalog connector.
18. Disconnect the test setup.
AWG5000C Series Arbitrary Waveform Generators Technical Reference 37
Performance Tests
Analog Amplitude Accuracy
Required equipment Prerequisites
Digital multim e ter
50 BNC cable
50 BNC termination
BNC-dual banana adapter
(See page 22, Prerequisites.)
1. Perform Mea
suring the Termination Resistance. (Seepage35.)
2. Press the All Outputs On/Off button on the instrument to turn off all the outputs.
3. Use the 50 Ω BNC cable, 50 BN C termination, and BNC-dual banana adapter to connect the Channel 1 Analog c onnector on the instrument to the HI and LO inputs on the digital multimeter. (See Figure 9.)
4. Press th
e Factory Default button on the instrument.
5. Press the Ch 1 Select button on the instrument.
6. On the i
nstrument, load the dc_plus waveform as an output waveform.
a. Select File > Open File.
b. In the
dialog box, navigate to the C:\Program Files\Tektronix\AWG\System\PV directory, and then select the pv_awg5000.awg le. The Waveform List window appears.
c. In the window, select (drag and drop) the dc_plus waveform on the User
ned tab.
De
7. Press the Ch 1 On button on the instrument to enable the channel 1 output.
ess the Run button on the instrument to output the waveform.
8. Pr
9. Set the amplitude and output mode of the instrument as shown in the rst row
of the table. (See Table 28.)
Table 28: Analog amplitude accuracy
Amplitude settings Output mode settings Accuracy limits
20 mV
200 mV
500 mV
1.0 V
p-p
2.0 V
p-p
4.5 V
p-p
20 mV
200 mV
600 mV
p-p
p-p
p-p
p-p
p-p
p-p
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: Off
Direct D/A out: On
Direct D/A out: On
Direct D/A out: On
17.6 mV to 22.4 mV
194 mV to 206 mV
488 mV to 512 mV
0.978 V to 1.022 V
1.958 V to 2.042 V
4.408 V to 4.592 V
17.6 mV to 22.4 mV
194 mV to 206 mV
586 mV to 614 mV
38 AWG5000C Series Arbitrary Waveform Generators Technical Reference
Performance Tests
10. Measure the out Measured_voltage_1.
11. Use the follow
termination:
V_high = [(T
Where Term_R is the resistance of the 50 BNC termination measured in step 3. (See
12. In the Waveform Li st window, select the dc_minus waveform on the User Dened tab
13. Measure the output voltage on the digital multimeter and note the value as Measured
14. Use the following formula to compensate the voltage for the 50 BNC
termina
V_low = [(Term_R + 50) / (2 × Term_R)] × Measured_voltage_2
Where Term_R is the resistance of the 50 BNC termination measured in step 3. (See page 35.).
15. Verify that the voltage difference |(V_high-V_low)| falls within the limits given in the table. (See Table 28.)
tion:
put voltage on the digital multimeter and note the value as
ing formula to compensate the voltage for the 50 BNC
erm_R + 50) / (2 × Term_R)] ×Measured_voltage_1
page 35.)
.
_voltage_2.
16. Repeat steps 9 through 15 for each amplitude setting in the table. (See
Table 28. )
17. Move the BNC termination from the Channel 1 Analog connector to the Channel 1 A
nalog connector.
AWG5000C Series Arbitrary Waveform Generators Technical Reference 39
Performance Tests
18. Repeat steps 9 t
19. Repeat steps 7 through 18 for the Channel 2 output.
20. For the AWG5014C: Repeat the test for the Channel 3 and Channel 4 outputs.
21. Press the All Outputs On/Off button on the instrument to turn off all the
outputs.
22. Disconnect the test setup.
Analog Harmonic Distortion
Required equipment Prerequisites
Spectrum analyzer
50 BNC cable
BNC-N adapter
1. Press the All Outputs On/Off button on the instrument to turn off all the outputs.
2. Use the 50 BNC cable and BNC-N adapter to connect the Channel 1 Analog connector on the instrument to the INPUT connector on the spectrum analyzer.
hrough 16.
(See page 22, Prerequisites.)
Figure 10: Equipment connections for verifying the analog harmonic distortion
3. Set the spectrum analyzer as follows:
a. Center frequency: 100 MHz
b. Span: 200 MHz
c. RBW: 20 kHz
4. Press the Factory Default button on the
instrument.
5. Press the Ch 1 Select button on the instrument.
40 AWG5000C Series Arbitrary Waveform Generators Technical Reference
Performance Tests
6. On the instrume
nt, load the sine_32 waveform as an output waveform.
a. Select File > Open File.
b. In the dialog box, navigate to the C:\Program
Files\Tektronix\AWG\System\PV directory, and then select the pv_awg5
000.awg le. The Waveform List window appears.
c. In the window, select (drag and drop) the sine_32 waveform on the User
Dened tab.
7. Press the Ch 1 On button on the instrument to enable the channel 1 output.
8. Press the Run button on the instrument to output the waveform.
9. Make the settings shown in the rst row (or corresponding row for your
instrument) of the following table:
Table 29: Analog harmonic distortion
AWG5000C model and settings Measurement frequency (MHz)
Model
AWG501C
AWG5002C
Output mode
Direct D/A out: Off
Direct D/A out: On
Direct D/A out: Off
Direct D/A out: On
Amplitude
2.0 V
p-p
0.6 V
p-p
2.0 V
p-p
0.6 V
p-p
Sampling rate (output frequency)
1.2 GS/s (37.5 MHz)
600 MS/s (18.75 MHz)
2nd 3rd 4th 5th
75
37.5 56.25
112.5 150 187.5
75
93.75
Accuracy limit
Nth reference
–40 dBc
–49 dBc
–46 dBc
–55 dBc
10. Use
the delta measurement function of the spectrum analyze r to measure
harmonic distortion of each measurement frequency.
rify that the harmonic distortion falls within the limits given in the table.
11.Ve
(See Table 29.)
epeat steps 9 through 11 for each setting in the table. (See Table 29.)
12.R
13. Move the 50 BNC cable from Channel 1 A nalog connector to the
Channel 2 Analog connector.
14. Repeat steps 7 through 12 for the Channel 2 output.
15. For the AWG5014C: Repeat the test for the Channel 3 and Channel 4 outputs.
16. Press the All Outputs On/Off button on the instrument to turn off all the
outputs.
17. Disconnect the test setup.
AWG5000C Series Arbitrary Waveform Generators Technical Reference 41
Performance Tests
Analog Non-Ha
rmonic Spurious Signal
Required equipment Prerequisites
Spectrum analyzer
50 BNC cable
BNC-N adapter
1. Press the Al outputs.
2. Use the 50 connector on the instrument to the INPUT connector on the spectrum analyzer.
l Outputs On/Off button on the instrument to turn off all the
BNC cable and BNC-N adapter to connect the Channel 1 Analog
(See page 22, Prerequisites.)
re 11: Equipment connections for verifying the non-harmonic spurious signal
Figu
3. Pres
4. Press the Ch1 Select button on the instrument.
5. On the instrument, load the sine_32 waveform as an output waveform.
6. Press the Ch 1 On button on the instrument to enable the channel 1 output.
7. Press the Run button on the instrument to output the waveform.
stheFactory Default button on the instrument.
a. Select File > Open File.
b. In the dialog box, navigate to the C:\Program
Files\Tektronix\AWG\System\PV directory, and then select the pv_awg5000.awg le. The Waveform List window appears.
c. In the window, select (drag and drop) the sine_32 waveform on the User
Dened tab.
42 AWG5000C Series Arbitrary Waveform Generators Technical Reference
Performance Tests
8. Make the instru
ment and spectrum analyzer settings shown in the rst row or
the second row of the following table:
Table 30: Analog non-harmonic spurious signal
AWG5000BC model and settings Spectrum analyzer settings
Model
AWG501xC Direct D/A out:
AWG5002C Direct D/A out:
Output mode
Off
Off
Amplitude
2.0 V
p-p
2.0 V
p-p
Sampling rate (outpu frequency)
1.2 GS/s (37.5 MHz)
600 MS/s (18.75 MH
Center
t
frequency
400 MHz 800 MHz 20 kHz –60 dBc
200 MHz 400 MHz 20 kHz –60 dBc
z)
Span
9. Use the spectrum analyzer to measure non-harmonic spurious signal of the Analog output over a frequency range of DC to 600 MHz (for the AWG5002C, DC to 300 MHz). For example, note the reference level of the fundamental waveform, and then measure each spurious.
10. Verify that the non-harmonic spurious signal falls within the limits given in the table. (See Table 30.)
11. Move the 50 BNC cable from the Channel 1 Analog connector to the Channel 2 Analog connector.
RBW Accuracy limit
Analog Phase Noise
12. Repeat steps 6 through 10 for the Channel 2 output.
13. For the AWG5014C: Repeat the test for the Channel 3 and Channel 4 outputs.
14. Press the All Outputs On/Off button on the instrument to turn off all the
outputs.
15. Disconnect the test setup.
Required equipment Prerequisites
Spectrum analyzer
50 BNC cable
BNC-N adapter
(See page 22, Prerequisites.)
1. Press the All Outputs On/Off button on the instrument to turn off all the outputs.
2. Use the 50 BNC cable and BNC-N adapter to connect the Channel 1 Analog connector on the instrument to the INPUT connector on the spectrum analyzer.
AWG5000C Series Arbitrary Waveform Generators Technical Reference 43
Performance Tests
Figure 12: Equipment connections for verifying the analog phase noise
3. Press the Factory Default button on the instrument.
4. On the instrument, load the sine_32 waveform as an output waveform.
a. Select File > Open File.
b. In the dialog box, navigate to the C:\Program
Files\Tektronix\AWG\System\PV directory, and then select the pv_awg5000.awg le. The Waveform List window appears.
c. In the window, select (drag and drop) the sine_32 waveform on the User
Dened tab.
5. Press the Ch 1 On button on the instrument to enable the channel 1 output.
6. Press the Run button on the instrument to output the waveform.
7. Make the instrument and spectrum analyzer settings shown in the rst row (or
the second row for your instrument) of the table. (See Table 31.)
8. Use the spectrum analyzer to measure phase noise of the Analog output.
9. Ve
rify that the analog phase noise at 10 kHz offset falls within the limits
given in the following table:
Table 31: Analog phase noise
AWG5000C model and settings Spectrum analyzer settings
Model
AWG501xC Direct D/A out:
AWG5002C Direct D/A out:
Output mode
Off
Off
Amplitude
2.0 V
p-p
2.0 V
p-p
Sampling rate
1.2 GS/s
600 MS/s
Center frequency
37.5 MHz 50 kHz 100 Hz
18.75 MHz 50 kHz 100 Hz
Span
RBW Accuracy Limit
at 10 kHz offset
–85 dBc/Hz
–85 dBc/Hz
44 AWG5000C Series Arbitrary Waveform Generators Technical Reference
Performance Tests
10. Move the 50 BNC Channel 2 Analog connector.
11. Repeat steps 5
12. For the AWG5014C: Repeat the test for the Channel 3 and Channel 4 outputs.
13. Press the All Outputs On/Off button on the instrument to turn off all the
outputs.
14. Disconnect the test setup.
cable from the Channel 1 Analog connector to the
through 9 for the Channel 2 output.
re 13: Example of the analog phase noise measurement
Figu
AWG5000C Series Arbitrary Waveform Generators Technical Reference 45
Performance Tests
Marker High and Low Level Accuracy
Required equipment Prerequisites
Digital multim e ter
50 BNC cable
50 BNC termination
BNC-dual banana adapter
1. Perform Measuring the Termination Resistance. (Seepage35.)
2. Press the All Outputs On/Off button on the instrument to turn off all the
outputs.
3. Use the 50 Ω BNC cable, 50 BN C termination, and BNC-dual banana adapter to connect the Channel 1 Mkr 1 connector on the instrument to the HI and LO inputs on the digital multimeter.
(See page 22, Prerequisites.)
Figure 14: Equipment connection for verifying the marker high and low level accuracy
4. Press the Factory Default button on the instrument.
5. Press the Ch1 Select button on the instrument.
6. On the instrument, load the marker_hi waveform as an output waveform.
a. Select File > Open File.
b. In the dialog box, navigate to the C:\Program Files\Tektronix\AWG\
System\PV directory, and then select the pv_awg5000.awg le. The Wavef orm List window appears.
c. In the window, select the marker_hi waveform on the User Dened tab.
7. Press the Ch 1 On button on the instrument to enable the channel 1 output.
8. Press the Run button on the instrument to output the waveform.
46 AWG5000C Series Arbitrary Waveform Generators Technical Reference
Performance Tests
9. Make the instru
ment High Level setting shown in the rst row of the
following table:
Table 32: Marker High and Low level accuracy
High level settings Accuracy limits
+2.7 V 2.31 V to 3.09 V
+1.0 V 780 mV to 1220 mV
0.0 V –120 mV to +120 mV
–0.9V –1.11Vto0.69V
Low level settings Accuracy limits
+2.6 V 2.22 V to 2.98 V
+1.0 V 780 mV to 1220 mV
0.0 V –120 mV to +120 mV
–1.0 V –1220 mV to –780 mV
10. Measure the output voltage on the digital multimeter and note the value as Measured_voltage_1.
11. Use the following formula to compensate the voltage for the 50 BNC
termination:
Marker_High = (Term_R + 50) / (2 Term_R) Measured_voltage_1
Where Term_R is the resistance of the 50 BNC termination measured in step 3. (See page 35.)
12. Verify that the marker High level falls within the limits given in the table. (See Table 32.)
13. Repeat steps 9 through 12 for each row in the table. (See Table 32.)
14. In the Waveform List window, select the marker_low waveform on the User Dened tab.
15. Press the Ch 1 On button on the instrument to enable the channel 1 output.
16. Press the Run button on the instrument to output the waveform.
17. Make the instrument Low Level s etting shown in the rst row of the table.
18. Measure the output voltage on the digital multimeter and note the value as Measured_voltage_2.
19. Use the following formula to compensate the voltage for the 50 BNC
termination:
Marker_Low = (Term_R + 50) / (2 Term_R) Measured_voltage_2
Where Term_R is the resistance of the 50 BNC termination measured in step 3. (See page 35.)
20. Verify that the marker Low level falls within the limits given in the table.
AWG5000C Series Arbitrary Waveform Generators Technical Reference 47
Performance Tests
21. Repeat steps 17
22. Press the Ch 1 On button to disable the channel 1 output.
23. Move the BNC termination from the Channel 1 Mkr 1 connector to the
Channel 1 Mkr 2 connector.
24. Repeat steps 7 through 21.
25. Move the 50 BNC termination from Channel 1 Mkr 2 connector to the
Channel 2 Mkr 1 connector.
26. Repeat steps 7 through 24 for the Channel 2 m arker outputs.
27. For the AWG5014C: Repeat the test for the Channel 3 and Channel 4 marker
outputs.
28. Press the All Outputs On/Off button on the instrument to turn off all the outputs.
29. Disconnect the test setup.
Marker Output Delay Accuracy
Required equipment Prerequisites
Sampling oscilloscope
Two 50 BNC cable
Two BNC-SMA adapters
through 20 for each row in the table.
(See page 22, Prerequisites.)
1. Press the All Outputs On/Off button on the instrument to turn off all the outputs.
2. Use a 50 BNC cable and BNC-SMA adapter to connect the Channel 1 Mkr 1 connector on the instrument to the CH1 connector on the sampling
cilloscope.
os
3. Use the 50 BNC cable and BNC-SMA adapter to connect the Channel 1
kr 2 connector on the instrument to the TRIGGER DIRECT connector on
M the sampling oscilloscope.
48 AWG5000C Series Arbitrary Waveform Generators Technical Reference
Figure 15: Equipment connections for verifying the marker output delay accuracy
Performance Tests
4. Set the sampling oscilloscope as follows:
a. Vertical scale: 250 mV/div
b. Horizontal scale: 500 ps/div
c. Trigger source: External Direct
d. Trigger level: 150 mV (or Set to 50%)
e. Trigger slope: positive
f. Measure: Pulse measurement > Pulse Time > Delay
5. Press the Factory Default button on the instrument.
6. On the instrument, load the square1 waveform as an output waveform.
a. Select File > Open File.
b. In the dialog box, navigate to the
System\PV directory, and then select the pv_awg5000.awg le. The Waveform List window appears.
c. In the window, select the square1 waveform on the User Dened tab.
7. Press the Ch 1 On button on the instrument to enable the channel 1 output.
8. Press the Run button on the instrument to output the waveform.
C:\Program Files\Tektronix\AWG\
9. On the oscilloscope, store the channel 1 waveform to Ref 1 as a reference
waveform.
10. On the instrument, set the Marker 1 delay value to 1.00 ns.
AWG5000C Series Arbitrary Waveform Generators Technical Reference 49
Performance Tests
11. Use the oscillo and channel 1 waveform at the 50% level.
12. Verify that th
13. Press the Ch 1 On button on the instrument to disable the channel 1 output.
14. Move the 5 0 BNC cable from the Channel 1 Mkr 1 connector to the
Channel 1 Mkr 2 connector and from Channel 1 Mkr 2 connector to the Channel Mkr
15. Press the Ch 1 On button on the instrument to enable the channel 1 output.
16. On the oscilloscope, store the channel 1 waveform to Ref 1 as a reference
waveform.
17. On the instrument, set the Marker 2 delay value to 1.00 ns.
18. Repeat steps 11 and 12.
19. Repeat steps 7 through 18 for the Channel 2 markers.
20. For the AWG5014C: Repeat the test for the Channel 3 and Channel 4 marker
outputs.
21. Press the All Outputs On/Off button on the instrument to turn off all the outputs.
scope to measure the delay time between the Ref 1 waveform
e delay time is within the range of 700 ps to 1300 ps.
1 connector.
22. Disconnect the test setup.
50 AWG5000C Series Arbitrary Waveform Generators Technical Reference
Performance Tests
DC Output Volt
age Accuracy
Required equipment Prerequisites
Digital multimeter
DC output lead set
Test leads (provided with the digital multimeter)
1. Use the test
2. Use the DC output lead set to connect the DC Output connector on the
instrumen
(See page 22, Prerequisites.)
leads to connect the HI and LO inputs o n the digital multimeter.
t.
Figure 16: Equipment connection for verifying the DC output voltage accuracy
3. Set the digital multimeter to the VDC mode.
4. On the instrument, select the DC Outputs tab in the Settings window.
5. OntheDCOutputtab,settheDC1,DC2,DC3,andDC4levelstothe
setting shown in the rst row of the following table:
Table 33: DC output voltage accuracy
DC output settings Accuracy limits
+5V 4.73Vto5.27V
+3 V 2.79 V to 3.21 V
0.0 V –120 mV to +120 mV
–3 V –3.21 V to –2.79 V
6. On the DC Outputs tab, select the DC Output check box to enable the DC output. The DC Output LED on the front panel lights.
7. Attach the black test lead to the connector lead from DC1 GND.
AWG5000C Series Arbitrary Waveform Generators Technical Reference 51
Performance Tests
8. Attach the red t
9. Verify that the DC output level falls within the limits given in the table.
(See Table 33.
10. Repeat steps 8 and 9 for DC 2, DC 3, and DC 4.
11. Repeatsteps5through10foreachrow in the table. (See Table 33.)
This completes the performance verication.
est lead to the connector lead from DC1.
)
52 AWG5000C Series Arbitrary Waveform Generators Technical Reference
Loading...