AWG2005.
Features
Specs
Ordering Information
Pricing Information
Request a Quote
20 MS/sec Arbitrary Waveform
Generator
AWG2005
Characteristics
Standard Waveshapes
Sine, square, triangle, ramp, noise, arbitrary, linked sequence,
and DC.
Arbitrary Waveforms
Execution Memory - Waveform: 64 k (65,535) for each
channel. Marker: 64 k for each channel. Waveform Size: 16 to
64 k in multiples of 16.
Real-time Sequence Memory - 8 k individual waveforms.
Loop Counter - Waveform: 1 to 64 k repeats. Sequence: 1 to 64
k repeats.
Catalog Memory - 2 MB.
Catalog Memory Clock
Frequency Range - 0.01 Hz to 20 MHz.
Resolution - Standard: 4 digits. With Option 05: 7 digits.
Accuracy - Standard: 50 ppm (+15°C to +30°C). Option 05:
5ppm (+15°C to +30°C).
Operating Modes
Continuous - Output waveform/sequence continuous at
programmed parameters.
Triggered - Output quiescent until triggered by an external,
GPIB, or manual trigger; generates a waveform/sequence only
one time.
Gated - Same as continuous mode except period is executed
only for the duration of the gated signal until the sequence is
completed.
Seq/Wfm Advance - Continuous: Continuously outputs the
waveform/sequence in the Sequence file. The next trigger
advances to the next waveform/sequence. Master/Slave
Operation.
Step - Output quiescent until triggered; then execute the next
waveform/sequence in the Sequence file. When the loop count
reaches its value, output stops and waits for next trigger.
Auto Step - Continuous: Continuously outputs the
waveform/sequence in the Auto Step file. Step: Output
quiescent until triggered.
Master - Provides Point Rate Clock and Trigger to a slave
arbitrary waveform generator for phase synchronous parallel
operation.
Slave - Receives Clock and Trigger from a system clock for
parallel operation.
Main Output
Digital-to-analog Resolution - 12-Bits.
Output Impedance - 50 Ohm.
Amplitude (1 MHz Clock, 000 and FFF Waveform Data,
Norm, No Filter, No Offset, Excluding and ADD Operation)
-
Range: 0.05 V to 10 V
p-p
into 50 Ohm.
Resolution: 1 mV (4 digits).
DC Accuracy: 0.050 V to 0.999 V, ±(0.5% of amplitude +
5 mV); 1.000 V to 10.000 V, ±(1% of amplitude + 50 mV).
Offset -
Range: -5.0 V to +5.0 V into 50 Ohm (-200 mA to +200 mA).
Resolution: 5 mV (4 digits).
Accuracy (1 MHz clock, 7FF waveform data, norm, no filter,
amplitude range 0.05 V): -±(1% of offset + 10 mV).
Pulse Response (20 MHz clock, 000 and FFF waveform data,
norm, no filter, amplitude 5 V, no offset) -
Rise/Fall Time: < 35 ns.
Flatness: Within ±3% after 150 ns from rise/fall edges.
Aberrations: Within ±7%.
Cross Talk Between Channels - 512-point sine, 20 MHz clock,
norm, no filter, amplitude offset. <70 dBc.
Noise Floor -
20 MHz clock, 7FFF waveform data, norm, no filter, no offset.
0.5 V: <110 dBm/Hz at 1 MHz.
5.0 V: <95 dBm/Hz at 1 MHz.
Sinewave Characteristics - Function Generator mode, 100 Hz
to 200 kHz, no offset. Flatness (1 V amplitude, 1 kHz
reference): Within -4%. T.H.D. (Including up to 4th harmonics):
<55 dBc at 5.0 V.
Auxiliary Outputs
Marker -
Amplitude: >2 V into 50 Ohm.
Impedance: 50 Ohm.
Marker to Signal Delay: 35 ns.
Clock -
Amplitude: >2 V into 50 Ohm.
Impedance: 50 Ohm.
Control Sig. -
Amplitude: >2 V into 50 Ohm.
Impedance: 50 Ohm.
Sweep (Opt. 05) -
Waveshape: Same waveshape as selected sweep.
Amplitude: 0 to 5 V (amplitude is dependent upon start and stop
frequencies with a 5 V maximum limit).
Impedance: 600 Ohm.
24-Bit TTL Digital Data Out (Opt. 04) -
Output Signals (CH 1 and CH 2): D0 to D11, Clock.
Level: TTL.
Amplitude: 2 V into 50 Ohm.
Skew Between Data: Within ±10 ns.
Clock to Data Delay: Within ±10 ns.
Impedance: 50 Ohm.
Auxiliary Inputs
Trigger -
Threshold Level: -5 V to +5 V.
Resolution: 0.1 V.
Accuracy: ±(5% of Level + 0.1 V).
Minimum Pulse Width: 150 ns.
Minimum Input Swing: 0.2 V
p-p
.
Maximum Input Volts: ±10 V (DC + peak AC).
Impedance: 10 kilohm.
Trigger to Signal Delay: Internal Clock, 400 ns (excluding clock
sweep mode).
AM (512-point Sine, 20 MHz Clock, AM, No Filter, 5 V
Amplitude, No Offset) -
Range: 2 V
p-p
(-1 V to +1 V) for 100% modulation.
Amplitude Accuracy: Within 5%.
Maximum Input Volts: -5 V (DC + peak AC).
Impedance: 10 kilohm.
ADD (512-point Sine, 20 MHz Clock, Add, No Filter, 5 V
Amplitude, No Offset) -
Range: 10 V
p-p
(-5 V to +5 V).
Amplitude Accuracy: Amplitude specification plus 5%.
Maximum Input Volts: -5 V (DC + peak AC).
Impedance: 50 Ohm.
Control Sig. -
Threshold Level: TTL level (0.8 V to 2.0 V).
Minimum Pulse Width: 40 ns.
Maximum Input Volts: 5 V to 0 V.
Impedance: 10 kilohm.
Clock -
Threshold Level: TTL level (0.8 V to 2.0 V).
Minimum Pulse Width: 20 ns.
Maximum Input Volts: 5 V to 0 V.
Impedance: External Clock, 330 Ohm; Slave Mode, 10 kilohm.
Frequency Range: 1 Hz to 20 MHz.
Sweep (Opt. 05 only) -
Type: Linear, log, arbitrary.
Mode: Continuous, triggered, gated.
Update Rate: 1 s to 65,535 ms.
Points per Sweep: 8 K maximum.
Function Generator
Waveform Shape - (Predefined 100 pt. waveforms). Sine,
Triangle, Square, Ramp, Pulse (1 MHz filter is inserted when
Sine is selected).
Frequency - 1.000 Hz to 200 kHz.
Duty Cycle - 0% to 100%, Pulse only.
Programmable Interface
GPIB - IEEE 488.2-1987 compatible.
RS-232 - 9-Pin D connector.
See Mixed Signal Sources, Intro for Environmental
Characteristics.
Top of Page
Features
Specs
Ordering Information
Pricing Information
Request a Quote
Product(s) complies with IEEE Standard
488.2-1987.
Product Area Assessed: The planning,
design/development and manufacture of
electronic Test and Measurement
instruments.
49A-10733-4p1, 06/1997, 07/21/2000
© Copyright Tektronix, Inc | webmaster@tek.com | Privacy Policy
Loading...