80A07
xx
ZZZ
Electrical Clock Recovery Instrument
User Manual
*P071219503*
071-2195-03
xx
80A07
ZZZ
Electrical Clock Recovery Instrument
User Manual
www.tektronix.com
071-2195-03
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14200 SW Karl Braun Drive
P.O. B o x 5 0 0
Beaverto
USA
For product information, sales, service, and technical support:
n, OR 97077
In North America, call 1-800-833-9200.
Worl dwid e, visi t www.tektronix.com to find contacts in your area.
Warranty
Tektronix warrants that this product will be free from defects in materials and workmanship for a period of one (1)
year from the date of shipment. If any such product proves defective during this warranty period, Tektronix, at its
option, either will repair the defective product without charge for parts and labor, or will provide a replacement
in exchange for the defective product. Parts, modules and replacement products used by Tektronix for warranty
work may be n
the property of Tektronix.
ew or reconditioned to like new performance. All replaced parts, modules and products become
In order to o
the warranty period and make suitable arrangements for the performance of service. Customer shall be responsible
for packaging and shipping the defective product to the service center designated by Tektronix, with shipping
charges prepaid. Tektronix shall pay for the return of the product to Customer if the shipment is to a location within
the country in which the Tektronix service center is located. Customer shall be responsible for paying all shipping
charges, duties, taxes, and any other charges for products returned to any other locations.
This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate
maintenance and care. Tektronix shall not be obligated to furnish service under this warranty a) to repair damage
result
b) to repair damage resulting from improper use or connection t o incompatible equipment; c) to repair any damage
or malfunction caused by the use of non-Tektronix supplies; or d) to service a product that has been modified or
integrated with other products when the effect of such modification or integration increases the time or difficulty
of servicing the product.
THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THE PRODUCT IN LIEU OF ANY
OTHER WARRANTIES, EXPRESS OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
TRONIX’ RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE
TEK
AND EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY.
TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS
ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.
[W2 – 15AUG04]
btain service under this warranty, Customer must notify Tektronix of the defect before the expiration of
ing from attempts by personnel other than Tektronix representatives to install, repair or service the product;
Table of Contents
General Safety Summary iii...................................
Environmental Considerations v...............................
Preface vii...................................................
Manual Structure vii................................................
Getting Started 1............................................
Clock Recovery 1.................................................
Key Features 2....................................................
Installation 3.....................................................
Electrostatic Discharge 3........................................
Static-Controlled Workstation 4...................................
Getting Acquainted with Your Instrument 5.............................
Input and Output Connector Care 6................................
Setting up the 80A07 7.............................................
Remote Interface 9................................................
Remote Control 9.................................................
User Adjustments 9................................................
Accessories 9.....................................................
Reference 11.................................................
Clock Recovery Ba sics 11............................................
User Interface 14...................................................
Standards Coverage 14..............................................
Specifications 19.............................................
Compliance Information 25....................................
EMC Compliance 25................................................
80A07 Clock Recovery User Manual
i
Table of Contents
ii
80A07 Clock Recovery User Manual
General Safety Summary
Review the following safety precautions to avoid injury and prevent damage to
this product or any products connected to it.
To avoid potential hazards, use this product only as specified.
Only qualified personnel should perform service procedures.
While using this product, you may need to access other parts of a larger system.
Read the safety sections of the other component manuals for warnings and
cautions related to operating the system.
ToAvoidFireor
Personal Injury
Use Proper Power Cord. Use only the power cord specified for this product and
certified for the country of use.
Connect and Disconnect Properly. Do not connect or disconnect probes or test
leads while they are connected to a voltage source.
Ground the Product. This product is grounded through the grounding conductor
of the power cord. To avoid electric shock, the grounding conductor must be
connected to earth ground. Before making connections to the input or output
terminals of the product, ensure that the product is properly grounded.
Observe All Terminal Ratings. To avoid fire or shock hazard, observe all ratings
and markings on the product. Consult the product manual for further ratings
information before making connections to the product.
The inputs are not rated for connection to mains or Category II, III, or IV
circuits.
Do not apply a potential to any terminal, including the common terminal, that
exceeds the maximum rating of that terminal.
Power Disconnect. The power cord disconnects the product from the power
source. Do not block the power cord; it must remain accessible to the user at all
times.
Do Not Operate Without Covers. Do not operate this product with covers or panels
removed.
Do Not Operate With Suspected Failures. If you suspect there is damage to this
product, have it inspected by qualified service personnel.
Avoid Exposed Circuitry. Do not touch exposed connections and components
when power is present.
Use Proper Fuse. Use only the fuse type and rating specified for this product.
Do Not Operate in Wet/Damp Conditions.
80A07 Clock Recovery User Manual
iii
General Safety Summary
Do Not Operate in an Explosive Atmosphere.
Keep Product Surfaces Clean and Dry.
Provide Proper Ventilation. Refer to the manual’s installation instructions for
details on installing the product so it has proper ventilation.
Terms in this Manual
Symbols and Terms
on the Product
These terms may appear in this manual:
WARNING. Warning statements identify conditions or practices that could result
in injury or loss of life.
CAUTION. Caution statements identify conditions or practices that could result in
damage to this product or other property.
These terms may appear on the product:
H DANGER indicates an injury hazard immediately accessible as you read the
marking.
H WARNING indicates an injury hazard not immediately accessible as you
read the marking.
H CAUTION indicates a hazard to property including the product.
The following symbol(s) may appear on the product:
CAUTION
Refer to Manual
Earth Terminal
WARNING
High Voltage
Chassis Ground
iv
Protective Ground
(Earth) Terminal
Standby
80A07 Clock Recovery User Manual
Environmental Considerations
This section provides information about the environmental impact of the
product.
Product End-of-Life
Handling
Restriction of Hazardous
Substances
Observe the following guidelines when recycling an instrument or component:
Equipment Recycling. Production of this equipment required the extraction and
use of natural resources. The equipment may contain substances that could be
harmful to the environment or human health if improperly handled at the
product’s end of life. In order to avoid release of such substances into the
environment and to reduce the use of natural resources, we encourage you to
recycle this product in an appropriate system that will ensure that most of the
materials are reused or recycled appropriately..
This symbol indicates that this product complies with the
applicable European Union requirements according to
Directives 2002/96/EC and 2006/66/EC on waste
electrical and electronic equipment (WEEE) and batteries.
For information about recycling options, check the
Support/Service section of the Tektronix Web site
(www.tektronix.com).
This product has been classified as Monitoring and Control equipment, and is
outside the scope of the 2002/95/EC RoHS Directive.
80A07 Clock Recovery User Manual
v
Environmental Considerations
vi
80A07 Clock Recovery User Manual
Preface
Manual Structure
This is the user manual for the 80A07 Electrical Clock Recovery instrument. The
manual covers capabilities, installation, operation, and specifications of the
instrument.
This manual is composed of the following chapters:
H Getting Started provides a brief product description and how to install your
instrument. Information about accessories to use with your product is also
found here.
H Reference provides more detail on the funtions and capabilites of the
instrument.
H Specifications lists the specifications for this instrument.
H Compliance Information lists the EMC (electromagnetic compliance)
standards with which the instrument complies.
80A07 Clock Recovery User Manual
vii
Preface
viii
80A07 Clock Recovery User Manual
Getting Started
Clock Recovery
This section contains information on key features of your instrument, installing
your instrument, and getting acquainted with the controls.
Many communication standards now specify that jitter testing must be carried
out using a reference clock that has been derived from the data signal. Typical
phase lock loop (PLL) characteristics are specified in terms of the --3 dB
bandwidth of the recovery loop, the rate of rolloff of the frequency response, and
the degree of response peaking allowable.
The 80A07 measures and displays the PLL frequency response from 100 kHz to
12 MHz. The 80A07 allows full control of parameters including loop bandwidth
(LBW), peaking/damping and rolloff.
Design and test engineers can now find and lock onto signals of undefined or
unknown data rates. The engineer can recover full-rate clocks, including spread
spectrum clocks, for signals at data rates from 100 Mb/s to 12.5 Gb/s. The
engineer has full control of key parameters for variable-loop bandwidth,
peaking/damping and first and second order rolloffs, optimizing jitter tracking.
Golden PLL
Recover Clocks for
Optical Storage,
Enterprise and Telecom
Testing
Many test standards require the use of a Golden PLL (phase lock loop.) To
assure repeatability, most serial data compliance test standards specify the PLL
characteristics for jitter measurement. Each standard provides an optimum LBW
setting for clock recovery, often called the Golden PLL.
The 80A07 has been designed to provide users with flexibility and accuracy in
compliance measurements. It is ideal for optical test applications, like 4x/8x
Fibre Channel and 10G Ethernet standards, where the signal under test must be
split off and converted from optical to electrical before being fed into the clock
recovery data input. The 80A07 recovers a full-rate clock up to 12.5 Gb/s, an
important requirement for testing XFP and other 10 Gb/s MSA modules.
80A07 Clock Recovery User Manual
1
Getting Started
Key Features
The 80A07 provides a quality clock recovery solution with the following
features:
H 100 Mb/s to 12.5 Gb/s continuous data rate coverage
H Accurate variable loop bandwidth from 100 kHz to 12 MHz
H Auto lock capability with LED display
H Programmable peaking adjustment with first and second order rolloff
capability
H Self-measured and displayed (Phase Locked Loop) PLL frequency response
H USB control connection or stand-- alone operation via front panel
H Single-ended or differential 50 Ω data inputs/outputs
H DC coupled data through path
H Full and divided clock outputs with selectable divide ratios
H Measurement of clock phase deviation as a function of frequency and time
H Data measurement capability
H Edge Density Measurement determines the mark density of the signal
under test
H Ideal for spread spectrum clock (SSC) applications with lar ge frequency
excursions
H Four memory locations for saving user setups
2
80A07 Clock Recovery User Manual
Installation
Getting Started
To install the 80A07, connect the supplied AC power cord to a properly
grounded AC supply. The input voltage requirement is 100 VAC to 240 VAC at
50 Hz to 60 Hz.
Press the power button on the instrument using the front-panel On/Standby
switch.
AC power
connector
Figure 1: Installation
Electrostatic Discharge
Power
button
To prevent electrostatic damage, follow the precautions described in this manual
and in the documentation provided with any connecting instruments.
Circuitry in the instrument is very susceptible to damage from electrostatic
discharge or from overdrive signals. Be sure to only operate in a static-controlled
environment. Be sure to discharge to ground any electrostatic charge that may be
present on the center and outer connectors of cables before attaching the cables.
80A07 Clock Recovery User Manual
3
Getting Started
Know your signal source. If it is capable of delivering overvoltages, it is safer to
not depend on the signal source settings for protection, but instead use an
external attenuator that protects the input from the worst-case conditions. For
example, for a 10 V maximum source connected to a 1 V maximum input, use a
10X attenuator. Where possible, connect your cables to the signal source first,
and to the instrument second.
CAUTION. To prevent damage from electrostatic discharge, install the 50 Ω
terminations on the I/O connectors when the connectors are not in use.
T o prevent damage to the instrument, discharge to ground any electrostatic
charge that may be present on the center and outer conductors of cables before
attaching the cables to the instrument.
T o prevent damage to the instrument, do not cr eate an ESD antenna by leaving
cables dangling off the input with the other end open.
Always use a wrist strap when making signal connections. Wear antistatic
clothing and work in a static-free workstation.
Static-Controlled
Workstation
T o prevent damage to the instrument, do not apply a signal outside the Maximum
Input Voltage Swing.
For information on creating a static-controlled workstation, consult the Electronic Industries Association document, EIA-625; Requirements for Handling
Electrostatic-Discharge-Sensitive (ESDS) Devices.
4
80A07 Clock Recovery User Manual
Getting Acquainted with Your Instrument
Getting Started
Ground for
antistatic
strap
Data input
Loop through data
output (terminate
with 50 Ω when
not in use)
Recovered clock with
programmable sub-rates
Lock button — Press to
initiate manual locking.
Lock range, min
10 MHz, max 500 MHz
Lock status indicator
Green -- locked
Amber -- locking
Red -- unable to lock
General Purpose knob:
--Adjust settings
--Scroll through menus
--Push to confirm settings
Left and right
cursor buttons
Escape button — Exit
submenus and revert
to previous values
Power
on button
Enter button:
--Scroll through menus
--Change digits when editing
--Select settings for adjustment
--Confirm editing changes
Measured values
Status indicators
Figure 2: 80A07 front panel and display
Device settings
80A07 Clock Recovery User Manual
5
Getting Started
Edge Density. The instrument
measures and displays the average
edge density of the input data.
Device Settings. Nominal frequency of
the data input signal, loop bandwidth,
and peaking (up to 6 dB) are
configurable on the front panel display.
Phase Deviation. The clock extraction circuit
produces a phase difference between incoming
data and CR clock output. The phase deviation
Figure 3: 80A07 display details
AC power
connector
Figure 4: 80A07 rear panel
is displayed in % peak-peak and %RMS.
USB
Standards. 24 preprogrammed
industry standards available via the
front panel interface. Custom settings
can be programmed and saved.
Auxiliary output connectors
Input and Output
Connector Care
The input and output connectors on the front panel are highly sensitive connectors providing high-frequency signal connections. To maintain signal integrity, it
is important not to damage these connectors.
Never attach a cable to a connector if the cable has a worn or damaged connector
because you may damage the connector. When attaching or removing a cable
from the connectors, align the connectors carefully before turning the nut. Then
turn only the nut, not the cable. Use light finger pressure to make the initial
connection, then tighten the nut lightly with a wrench.
6
80A07 Clock Recovery User Manual
Setting up the 80A07
Getting Started
CAUTION. To prevent electrostatic damage to the 80A07 and other instrumentation, follow the precautions described in this manual and in the documentation
provided with any connecting instruments. (See Electrostatic Dischar ge starting
on page 3.)
NOTE. For best repeatability and to prolong connector life, use a torque wrench,
and tighten the connection to the range of 79-112 N⋅cm (7-10 in lb).
If the connectors receive heavy use, such as in a production environment, you
should install adapters to make connections.
After the proper connections have been made for data input and clock out, and
the instrument has been powered on, you may adjust the input settings.
NOTE. The DATA OUTPUT connectors must be terminated if not in use, or else
the reflections that result will severely degrade performance.
Current settings are displayed on the right side of the display. Use the knob or
cursor buttons to scroll through menu items. Press the knob or enter button to
select an item to adjust. Use the ESC button to back out of a menu or cancel an
adjustment. When editing a numeric setting, use the left and right cursor buttons
to move through digits and use the knob to make changes. Press the knob or
ENTER button to accept a change, or press the ESC button to cancel changes.
Many industry standards are also available from the front panel menu. After
selecting a standard, the nominal data rate, loop bandwidth and peaking settings
are entered automatically.
You can manually enter the following settings:
H Nominal Data
Rate
H Lock Range The frequency range around the nominal rate that
H Bandwidth Bandwidth of the recovery loop measured at
Nominal rate of the recovered clock.
will be scanned during locking.
-- 3 d B .
H Peaking Peaking of the recovery loop. Also sets 1st or 2nd
H Nominal Edge
80A07 Clock Recovery User Manual
Density
order roll-off of untracked jitter.
Expected edge density of incoming data.
Required to set bandwidth correctly.
7
Getting Started
H Edge Density Mode Sets bandwidth. Calculations are based on the
Expected Edge Density (user entered) or edge
density measured during lock.
H Clock Amplitude Output amplitude of the full-rate clock.
H Sub-rate Amplitude Output amplitude of the sub-rate clock.
H Sub-rate Division Division ratio of the sub-rate clock.
All settings are saved automatically at power of f and restored at power on. You
can also save current settings to one of four Setups that can be recalled later.
The left side of the display provides several continuously updated measurements:
H Frequency The measured frequency of the recovered clock.
H Phase Error The peak-to-peak phase error between the
incoming data and the recovered clock. This
measured value increases if jitter is present on the
input data that is not being tracked by the
recovered clock.
H Phase Error RMS The RMS phase error between the incoming data
and the recovered clock.
H Lock State Reports whether the CR is locked, unlocked, or in
the process of locking.
By default, the 80A07 is configured in Auto Lock Mode, where it automatically
attempts to acquire lock if the detected Phase Error exceeds the Phase Error
Limit setting or if the recovered clock is unstable. The user may force a relock at
any time by pressing the Lock button.
You can utilize the 80A07 with a Tektronix sampling oscilloscope such as the
DSA8200 Digital Serial Analyzer, to display the data input. Use the clock output
to trigger the oscilloscope. Figure 5 shows a typical setup configuration.
Figure 5: Typical setup configuration
8
80A07 Clock Recovery User Manual
Remote Interface
Remote Control
Getting Started
The 80A07 can be remotely controlled via the virtual front panel software. The
virtual front panel software can be installed on a personal computer or a
Tektronix sampling oscilloscope. Connection to the 80A07 is made through the
USB interface. The virtual front panel software requires the Microsoft Windows
2000 or XP operating system.
The virtual front panel software is provided on the CDROM included with your
instrument. Insert the CDROM into the C DROM drive and follow the installation prompts. Refer to the user instructions on the CDROM for operation of the
virtual front panel software.
Remote control of the 80A07 is possible with the use of the Software Developer’s Kit (SDK). The SDK is available on the CDROM provided with your
instrument. Refer to the instructions provided on the CDROM for use of the
developer’s kit.
User Adjustments
The 80A07 contains no user adjustments.
80A07 Clock Recovery User Manual
9
Getting Started
Accessories
This section lists the standard and optional accessories available for the
instrument.
Standard Accessories
Optional Accessories
The following accessories are shipped with the instrument:
Table 1: Standard accessories
Item Part number
80A07 Electrical Clock Recovery User Manual 071--2195--xx
80A07 Software disc (Virtual Front Panel and software developer’s kit) 063--4040--xx
Power Cord 161--0104--xx
Rack mount hardware
Left bracket 119--7360--xx
Right bracket 119--7361--xx
Hardware bag (screws) 119--7363--xx
USB cable 174--4401--xx
Fuse 119--7362--xx
You can order the following accessories for use with the 80A07. Consult a
current Tektronix catalog for additions, changes, and details:
Table 2: Optional accessories
10
Item Part number
Cables (450 mm/18 inch; 1 dB loss @ 20 GHz) recommended for work
to 20 GHz.
SMA male 50 Ω termination 015--1022--xx
Connector saver, 3.5 mm SMA 015--0549--xx
SMA accessory kit 020--1693--xx
015--0560--xx
80A07 Clock Recovery User Manual
Reference
Clock Recovery Basics
A clock recovery system is used to generate a sampling clock from a stream of
data with an embedded clock. The sampling clock is then used by the decision
circuit to determine when to decide the logic state of the incoming data. In most
cases, the data is line coded in a format referred to as “Non-Return to Zero”
(NRZ). As the name implies, the logic state in NRZ data remains constant when
the data contains a series of bits with the same value, 1 or 0.
Jitter Transfer
Loop Response Peaking
Data
Clock
The clock recovery PLL (phased lock loop) removes virtually all of the low
frequency jitter from the input data and none of the very high frequency jitter
components. Periodic jitter with frequency components near the roll slope of the
PLL loop response will be attenuated by some degree. The Jitter Transfer
Function is a plot of the attenuation of the jitter passing from the input data to
the recovered clock output as a function of frequency content.
The Jitter Transfer Function is not exactly an inverse of the PLL loop frequency
response. The slope of the jitter transfer function, as well as its peaking will
often be different that of the PLL loop response.
1
00 0
11 1
80A07 Clock Recovery User Manual
11
Reference
PLL Loop
Response
Jitter Transfer Function
(roll off varies between
20 -- 40 dB/decade)
(constant
20 dB/decade
roll off)
The parameters which determine the JTF roll off slope and peaking are the
relationship between loop bandwidth and the bit rate, and the amount of peaking
in the PLL response. Several examples of the jitter transfer function versus PLL
loop response can be seen in the next section.
Golden PLL
Edge Density
The 80A07 has the ability to measure the PLL response and the jitter transfer
function and display a plot of these to the user. This can be useful to understand
the relationship of these parameters at the particular data rate.
Many test standards require the use of a Golden PLL (phase lock loop.)
The 80A07 is an instrumentation grade clock recovery system. The PLL
parameters of clock frequency, loop bandwidth and peaking are accurately
calibrated, and adjustable by the user. This is useful in two situations — during
transmitter testing when the user wants to measure parameters in the data signal
through the channel exactly as the receiver would, and for standards compliance
testing.
Because the clock recovery system removes the low frequency jitter from the
regenerated clock, the loop parameters must be calibrated and set to known
values for repeatable jitter measurements. To assure repeatability, most serial
data compliance test standards specify the PLL characteristics for jitter measurement. A PLL which is set to these specified parameters is often referred to as a
“Golden PLL”.
The logic state of NRZ data does not change between successive bits of the same
logic state. Therefore, there will not be a logic edge in every bit time slot, or
Unit Interval. The edge density refers to the average percentage of unit intervals
which contain a transition. A repeating 1010 pattern has a transition occurring
during every unit interval, and therefore an edge density of 100%. A Pseudo
Random Bit S tream (PRBS) pattern has an edge density of 50%. Other examples
12
80A07 Clock Recovery User Manual
Reference
include a repeating 1100 pattern, which has a 50% edge density, and a repeating
11110000 pattern, which would have an edge density of 25%.
All clock recovery systems require a minimum edge density to operate properly.
If a long pattern of all ones or zeros were sent, the clock recovery would not be
able to track jitter or spread spectrum clock (SSC) modulation or may even lose
lock on the data clock. Data encoding standards eliminate this possibility by
either modulating the bit stream using a set of rules that set a minimum for the
number of consecutive bits set to the same logic state, or add overhead data bits
to the packet which guarantee transitions occur even when the payload data is bit
stream of only one logic state.
The edge density represents the amount of energy going into the clock recovery
phase lock loop. The average energy effects the parameters of loop gain and
bandwidth. Therefore, an instrumentation grade clock recovery system such as
the 80A07 requires information on the edge density to keep the loop parameter
settings calibrated. In the 80A07, this can be done by one of two methods, auto
and manual modes. In auto mode, the actual average edge density is measured
and automatically calibrates the loop parameter settings. In manual mode, the
user enters the expected edge density. A warning message is generated when the
measured edge density varies greatly from the expected edge density. Some
serial data compliance standards, such as SATA, require the loop parameters be
calibrated to a specified edge density, regardless of the edge density of the actual
data.
Clock Multiplication and
Division
To lock to NRZ data, the phase detector used in a clock recovery PLL does not
require an edge at every unit interval. This property can be utilized to multiply a
clock frequency. The PLL will lock to a frequency that is a multiple of the clock
applied to the data input.
To multiply a clock, you enter the desired output frequency as the clock
frequency. This must be an integer multiple of the input frequency. To calibrate
the loop response (for known jitter transfer performance), you also enter the
preclinical of the multiplication factor in percent as the expected edge density.
For example, for 2X multiplication, enter 50%, for 3x enter 33%, for 5x enter
20% etc. The clock recovery unit will phase lock to the multiple of the input data
frequency, providing a clean multiple of the input clock at the output.
While the PLL can accept data with edges at a sub-multiple of the clock rate, it
can handle the converse -- edge rates greater than one per unit interval (corresponding to edge densities greater than 100%). Thus, the PLL itself can not be
used directly to divide a clock to a lower multiple.
The 80A07 provides an additional Sub-Rate Clock output which is divided to a
sub multiple of the main clock output. The 80A07 utilizes a user programmable
divider for this purpose. The divider is specifically designed to minimize the
addition of jitter to the recovered clock signal. This sub-rate clock output can be
used to precisely divide a clock down to a sub multiple frequency. The 80A07
80A07 Clock Recovery User Manual
13
Reference
User Interface
provides a large selection of division ratios, ranging from 1 to 648. To use the
clock recovery instrument as a precision clock divider, you would set the clock
frequency to the actual input frequency and the edge density to 100%. Then,
select the desired division ratio for the SUBRATE CLOCK output.
Note that because the divider circuits are located outside of the PLL, the
calibrated loop characteristics and jitter transfer function will scale in frequency
by the sub-rate divisor.
The 80A07 can be used in standalone operation or in conjunction with a
Tektronix sampling oscilloscope.
As a standalone instrument, information is always immediately available on the
front panel display, showing parameters such as the PLL bandwidth, lock status,
bit rate, peaking and rolloff.
For easy verification of compliance, the correct characteristics are automatically
set when a given standard is selected from a pull-down menu. However, full
control of parameters is possible with direct entry of the user parameters. The
80A07 has variable jitter peaking, allowing jitter gain in excess of 10 dB if
desired.
Standards Coverage
Remote control of the instrument is supported via USB and a software developer’s kit.
The 80A07 instrument provides a solution for triggering a DSA8200, CSA8000,
and TDS8000 Series instruments from single-ended or differential electrical
signals. The 80A07 can be used as a standalone clock recovery device or in
conjunction with the following Tektronix sampling oscilloscopes:
H DSA8200 Digital Serial Analyzer
H CSA8000, CSA8000B, and CSA8200 Communications Signal Analyzer
(with product software version 2.0 or later)
H TDS8000, TDS8000B, and TDS8200 Digital Sampling Oscilloscope
(with product software version 2.0 or later)
The following graphics show compliance settings, and the accompanying table
(Table 3) show common standards, the data rates they employ, and the loop
bandwidths required for compliance measurements.
14
80A07 Clock Recovery User Manual
Reference
L
R
(
dB)
0
-- 1 0
eponse
-- 2 0
oop
-- 3 0
-- 4 0
100kHz 1MHz 10MHz 100MHz
10kHz
10 Gigabit Ethernet
Bit Rate: 10.3125 Gb/s
Loop Bandwidth: 4 MHz
Peaking: 0 dB
Blue trace: Jitter Transfer Function (roll
off varies between 20 -- 40 dB/decade)
Red trace: PLL Loop Response
(constant 20 dB/decade roll off)
Legend
XAUI
Bit Rate: 3.125 Gb/s
Loop Bandwidth: 1.875 MHz
Peaking: 0 dB
2x Fibre Channel
Bit Rate: 2.12 Gb/s
Loop Bandwidth: 1.275 MHz
Peaking: 0.3 dB max
4x Fibre Channel
Bit Rate: 4.25 Gb/s
Loop Bandwidth: 2.55 MHz
Peaking: 0.3 dB max
8x Fibre Channel
Bit Rate: 8.5 Gb/s
Loop Bandwidth: 5.1 MHz
Peaking: 0.3 dB max
OIF CEI 11G+
Bit Rate: 11.0 Gb/s
Loop Bandwidth: 8 MHz
Peaking: 0.1 dB max
SONET OC-- 192/SDH STM--64
Bit Rate: 9.95 Gb/s
Loop Bandwidth: 4 MHz
Peaking: 0 dB
8x OIF CEI 6G+
Bit Rate: 6.25 Gb/s
Loop Bandwidth: 3.6 MHz
Peaking: 0.1 dB max
Serial ATA Gen 2 f
Bit Rate: 3.0 Gb/s
baud
/500
Loop Bandwidth: 6 MHz
Peaking: 2.1 dB
XFP/XFI
Bit Rate: 10.5 Gb/s
Loop Bandwidth: 8 MHz
Peaking: 0.1 dB max
OIF CEI 11G+
Bit Rate: 11.0 Gb/s
Loop Bandwidth: 4 MHz
Peaking: 0.1 dB max
Serial ATA Gen 2 f
Bit Rate: 3.0 Gb/s
baud
/1667
Loop Bandwidth: 0.9 MHz
Peaking: 0 dB
Fully Buffered DIMM II
Bit Rate: 6.4 Gb/s
Loop Bandwidth: 11 MHz
Peaking: 0.5 dB
OIF CEI 11G+
Bit Rate: 11.0 Gb/s
Loop Bandwidth: 6 MHz
Peaking: 0.1 dB max
SONET OC-- 48/SDH STM--16
Bit Rate: 2.488 Gb/s
Loop Bandwidth: 1 MHz
Peaking: 0 dB
PCI Express II
Bit Rate: 5.0 Gb/s
Loop Bandwidth: 5 MHz
Peaking: 1 dB max
80A07 Clock Recovery User Manual
15
Reference
/
/
/
y
DIM
M
FullSSCsw
i
Table 3: Standards supported
Standard
Data rate
(Gb/s)
Common
clock divide
ratios
Loop
bandwidth
(MHz)
Peaking
(dB)
Slope
Spread spectrum
clocking
Ethernet 1.0 0.637
10Gb/s Ethernet
Transmitter Test
10.312 ≤4 --20 dB/
decade
No
XAUI 3.125 1.875
Fibre 1X 1.063 10 0.638 0.3 max --20 dB/ No
Channel
2X
2.12 20 1.275 0.3 max
decade
4X 4.25 40 2.550 0.3 max
8X 8.5 80 5.100 0.3 max
OIF CEI
1
6+Gb/s 4.976 to
6.375
3.6
(f
baud
/1667)
0.1 max --20 dB/
decade
No
11+Gb/ s 9.95 to 11.1 8, ITU
6(f
/1667)
baud
other
2
SATA
Gen 1 250UI 1.5 15 6.000 Yes
f
/1667 0.900 2.09 --
baud
Type 2
1.25 dB
5UI 300.000
Gen 2 f
/500 3 30 6.000 2.09 --
baud
Type 2
1.25 dB
f
/1667 1.800 2.09 --
baud
Type 2
1.25 dB
f
/10 300.000 2.09 --
baud
Type 2
1.25 dB
SONET/ OC12/STM-4 0.622 0.250 --20 dB/ No
SDH
OC48/STM-16 2.488 1.000
decade
OC192/STM-64 9.95 4.000
XFP/XFI XFP/XFI Receiver
9.95 -- 11.2 64 8.000 0.1 max No
Test
Transmitter
Test
4.000 0.1 max --20 dB/
decade
Fully FB-DIMM1 3.2, 4.0 24 11 t o 3 3 0.5to3 2nd Order Yes.
Buffered
4.8 24 11 t o 2 2
FB-DIMM2 4.8, 6.4, 8.0,
9.6
Forwarded
Clock
11 t o 2 2 0.5to2
Transmitter Test:
Receiver Test: 0.06
UI swing.
ng.
16
80A07 Clock Recovery User Manual
Table 3: Standards supported (cont.)
ppp
g
Reference
Loop
bandwidth
(MHz)
8to16
Peaking
(dB)
Upto1dB
Upto3dB
Slope
--20 dB/
decade
1st or 2nd
order
Spread spectrum
clocking
Yes, Optional.
Receiver Test:
65 ps pk-pk swing
Standard
PCI
Express
3
SAS
Common
Data rate
(Gb/s)
clock divide
ratios
I 2.5 25 1.500 1st order with
II 5 50 5to16
Gen 1 f
/1667 1.5 15 0.900 1st order
baud
(single pole)
Gen 2 f
/1667 3 30 1.800 1st order
baud
(single pole)
1
8 MHz for most tests for ITU applications, BW/1667 other. Minimum of 4 MHz for stress testing in one case.
2
Gen 1 & 2 categories: “i” (internal, hard drives etc.) and “m” (medium reach) use f
baud
/500 and f
/10 for Gen 2 and
baud
250UI and 5UI for Gen 1.
“x” (extended reach) uses f
/1667, Type 2.
baud
Peaking bandwidths Implied: specified as damping factor of 0.707 min to 1.00 max — conversion taken from Gardner.
Loop bandwidths specified with transition density of 1 (100% or 1010101 pattern). Assumption is that loop bandwidth will
change proportionally as transition density reduces.
3
Specified as damping factor of 0.707 min to 1.00 max — conversion taken from Gardner.
Loop bandwidths specified with transition density of 1 (100% or 1010101 pattern). Assumption is that loop bandwidth will
change proportionally as transition density reduces.
80A07 Clock Recovery User Manual
17
Reference
14
Loop
Bandwidth
(MHz)
12
10
8
6
4
3
2
1.5
1
0
The 80A07 has a variable loop bandwidth from 100 kHz to 12 MHz. The calibrated loop bandwidth is limited as
indicated by the graph.
6
12
Figure 6: Clock recovery loop bandwidth versus data rate
Date Rate (Gb/s)
12
121086420
14
18
80A07 Clock Recovery User Manual
Specifications
This section contains specifications for the 80A07 Electrical Clock Recovery
instrument.
To meet specifications, two conditions must first be met:
H The instrument must have been operating continuously for 20 minutes within
the operating temperature range specified.
H The instrument must be in an environment with temperature, altitude, and
humidity within the operating limits described in these specifications
Table 4: Characteristics
Specifications Characteristics
Data inputs / outputs
Input configuration True differenti al
Output configuration True differential
Unused outputs must be terminated into 50 Ω.
Connector type APC 3.5
Impedance 50 Ω
Coupling DC
Insertion loss --2.6 dB or better
10 MHz to 12.5 GHz
Maximum nondestruct range 5V
Maximum operating range 5V
Input sensitivity
Single ended 30 mVppat 10 Gbps
Differential 15 mVppat 10 Gbps
Clock output
Connector type APC 3.5
Impedance 50 Ω
Coupling DC
Amplitude
Minimum 300 mV
Typical 540 mV
pk-pk
pk-pk
pp
pp
80A07 Clock Recovery User Manual
19
Specifications
Table 4: Characteristics (cont.)
Specifications Characteristics
Amplitude accuracy 10% or 30 mV
Duty cycle accuracy 3% UI
Jitter RMS, at 800 mVppinput, 10 Gps, 1010 pattern, 2 MHz BW, 0.5 dB peaking
Typical 70 fsec
Maximum 250 fsec
Return Loss -- 15 dB minimum
Rise/Fall 80/20% point measurements
Typical 25 ps
Maximum 30 ps
Subrate output
Connector type APC 3.5
Impedance 50 Ω
Coupling DC
Divider function from main
CLOCK OUTPUT
Full rate divided by 1, 2, 4, 5, 6, 7, 8, 9, 10, 12, 14, 16, 18, 20, 24, 25, 28, 30, 32, 35, 36, 40, 42,
45, 48, 49, 50, 54, 56, 60, 63, 64, 70, 72, 80, 81, 90, 100, 108, 112, 120, 126, 128, 140, 144, 160,
162, 168, 180, 192, 196, 200, 216, 224, 240, 252, 256, 280, 288, 320, 324, 336, 360, 384, 392,
432, 448, 504, 512, 576, 648.
Odd division ratios have non--50% duty cycles.
Amplitude Adjustable
Minimum 250 mV
Maximum 900 mV
pp
pp
Amplitude accuracy 10% or 30 mV
Measured at div by 1, typically ±25% for all division ratios
Duty cycle accuracy 5% UI
Measuredatdivby.1248163264128
Jitter RMS, at divide-by-1, 800 mVppinput, 10 Gps, 1010 pattern, 2 MHz BW, 0.5 dB peaking.
Typical 70 fs
Maximum 250 fs
Return loss
Minimum --15 dB
100 KHz to 12.5 GHz
Rise/fall 80/20% point measurements, divide-by-1
Typical 25 ps
Maximum 30 ps
20
80A07 Clock Recovery User Manual
Specifications
Table 4: Characteristics (cont.)
Specifications Characteristics
Control interface
Type USB 2.0
Uplink ports 1
Additional ports 3
Clock recovery response
Loop bandwidth Refer to graph for allowable data rate versus loop bandwidth combination settings, Adjustable
Minimum 100 KHz
Maximum 12 MHz
Frequency rolloff Adjustment of peaking also adjusts the frequency swi tchover point between low-frequency
--40 dB/decade rolloff rate and high--frequency --20 dB/decade rolloff rate.
Minimum 20 dB/dec
Maximum 40 dB/dec
Peaking Adjustable
Minimum 0dB
Maximum 6dB
Frequency range Adjustable
Minimum 100 Mbps
Maximum 12.5 Gbps
Frequency deviation +500/--5500ppm (+0.05/--0.55%)
30--33 KHz Modulation Rate
Bandwidth deviation ±2%
Measured with 1100 pattern at room temperature over 500 kHz to 12 MHz BW setting. Increased
deviation for BW settings below 500 KHz.
Peaking deviation ±10% of setting or 0.2 dB
Measured edge density
deviation
Phase error output Linear Volts/UI of phase error depends on edge density and is not calibrated. Bandwidth limited.
Connector type SMA
Impedance 50 Ω
Coupling DC
Frequency Track Output Volts/PPM of frequency variation (e.g. 5000 PPM gives 5 Vpp) is not calibrated.
Connector type SMA
Impedance 50 Ω
Coupling DC
±1%
80A07 Clock Recovery User Manual
21
Specifications
Table 4: Characteristics (cont.)
Specifications Characteristics
Trigger input External CR lock request
Connector type SMA
Impedance 50 Ω
Coupling DC(to0volts)
Threshold 1.5 V
Pulse width 50 ns minimum
Trigger output External lock status indicator
Connector type SMA
Impedance 50 Ω
Coupling DC
Latency 300 ms maximum
Table 5: Power consumption, fuses, and cooling
Specifications Characteristics
Source voltage and frequency 100VACto240VACat50Hzto60Hz
Fuse rating 3.15 A
Power requirements 150 W maximum
Table 6: Mechanical
Specifications Characteristics
Weight 20 lbs (9.1 kg)
Overall dimensions 15.5 in. W x 3.75 in. H x 13.75 in. D (394 mm W x 95 mm H x 337 mm x D)
The dimensions do not include feet or protruding connectors.
Table 7: Environmental specifications
Specification Characteristics
Dynamics
Vibration (operating) Meets MIL--PRF--28800F Class 3
Shock Meets MIL--PRF--28800F Class 3
Bench handling (operating) Meets MIL--PRF--28800F Class 3
22
80A07 Clock Recovery User Manual
Table 7: Environmental specifications (cont.)
Specification Characteristics
Atmospherics
Temperature
Operating +10 °Cto+40°C
Nonoperating -- 2 2 °Cto+60°C
Relative humidity
Operating 20% to 80% relative humidity with a maximum wet bulb temperature of +29 °C at or below
+40 °C.
Nonoperating 5% to 90% relative humidit y with a maximum wet bulb temperature of +29 °C at or b below
+60 °C.
Altitude
Operating 3,000 m (9,842 ft.)
Non-operating 12,190 m (40,000 ft.)
Specifications
80A07 Clock Recovery User Manual
23
Specifications
24
80A07 Clock Recovery User Manual
Compliance Information
This section lists the EMC (electromagnetic compliance) standards with which
the instrument complies.
EMC Compliance
EC Declaration of Conformity - EMC
Meets intent of Directive 2004/108/EC for Electromagnetic Compatibility.
Compliance was demonstrated to the following specifications as listed in the
Official Journal of the European Communities:
EN 61326- 1:2006, EN 61326-2- 1:2006. EMC requirements for electrical equipment
for measurement, control, and laboratory use.
123
H CISPR 11:2003. Radiated and conducted emissions, Group 1, Class A
H IEC 61000--4--2:2001. Electrostatic discharge immunity
H IEC 61000--4--3:2002. RF electromagnetic field immunity
H IEC 61000--4--4:2004. Electrical fast transient/burst immunity
H IEC 61000--4--5:2001. Power line surge immunity
H IEC 61000--4--6:2003. Conducted RF immunity
H IEC 61000--4--11:2004. Voltage dips and interruptions immunity
EN 61000- 3- 2:2006. AC power line harmonic emissions
EN 61000- 3- 3:1995. Voltage changes, fluctuations, and flicker
European Contact.
Tektronix UK, Ltd.
Western Peninsula
Western Road
Bracknell, RG12 1RF
United Kingdom
1
2
3
80A07 Clock Recovery User Manual
This product is intended for use in nonresidential areas only. Use in residential areas
may cause electromagnetic interference.
Emissions which exceed the levels required by this standard may occur when this
equipment is connected to a test object.
To ensure compliance with the EMC standards listed here, high quality shielded
interface cables should be used.
25
Compliance Information
Australia / New Zealand Declaration of Conformity - EMC
Complies with the EMC provision of the Radiocommunications Act per the
following standard, in accordance with ACMA:
H CISPR 11:2003. Radiated and Conducted Emissions, Group 1, Class A, in
accordance with EN 61326--1:2006 and EN 61326--2--1:2006.
26
80A07 Clock Recovery User Manual
Loading...