Tektronix CSA8000B, CSA8000, TDS8000, TDS8000B, 80A01 User manual

Read This First
80A00 and 82A0

0 Series Modules

Supported instruments

The 80A00 and
Digital Serial Analyzer, as well as the legacy TDS/CSA8000, TDS/CSA8000B,
and TDS/CSA/DSA8200 series instruments.

82A00 Series Modules are for use with the Tektronix DSA8300

Handle modules to prevent electrostatic damage

CAUTION. Electrostatic discharge (ESD) can damage sampling module electrical

inputs an

Always use a grounded wrist strap (provided with your instrument) when
installing o r removing modules from the mainframe and when connecting cables.

Wear anti-static clothing and work in a static-free workstation when u sing
sampling modules.

Discharge cables to ground before connecting them to modules.

Do not
input with the other end of the cable open.

d outputs.

create an ESD antenna by leaving cables attached to the sampling-module

www.tektronix.com
Copyright © Tektronix

Use a T
measurements.

Do no
assembly can result.

Alw
terminations installed.

To
connectors clean at all times. Check that all connectors, jumpers, and protective
caps are clean before connecting them to the module.

Do not transport or ship the instrument with the modules installed in the module
compartments.

ektronix 80A02 EOS/ESD Protection Module when taking TDR

t drop the module since damage and misalignment of the photodiode optical

ays store and transport modules in a static-free container, with all supplied

prevent loss of optical power or damage to the optical connectors, keep the

*P071138613*

071-1386-13

Read This First 80A00 and 82A00 Series Modules

Install a module

Figure 1: Module insertion

1. Connect an antistatic wrist strap to the instrument front-panel ground
connection. Place the strap on your wrist.

2. For optical modules, turn the module lock screws counterclockwise to rotate
the retaining tabs to a vertical position before inserting the module.

3. Use the power cycle that is appropriate for your instrument:

DSA830

greater: Click Tools > View/Change Module Config and follow the
on-screen instructions.

Legacy instruments and DSA8300 with TekScope application version

6.0.X: Power off the instrument using the front-panel On/Standby switch.

4. Push the module into a compartment, using firm pressure. When the module

is se ated, turn the lock screw(s) clockwise to tighten the module in the slot.

5. Power on the instrument (legacy instruments or DSA8300 with TekScope

6.0.X software) or complete the View/Change Module Config process
(TekScope version 6.1.X and later). Let the instrument warm up for
20 minutes.

NOTE. The warm-up cycle is not required if you installed the module using the

iew/Change Module Configfunction(TekScopeversion6.1.Xandlater).

V

6. In the TekScope application, click Utilities > Compensate and run
a compensation on the newly-installed module. You must also run a
compensation if a module is moved from one slot to another, or an extender
is installed, changed, or removed from a module.

0 instruments with TekScope application version 6.1.X and

2 80A00 and 82A00 Sampling Modules Read This First

Read This First 80A00 and 82A00 Series Modules

Remove a module

7. Use the Differe
DiffChAlign)toalignbothchannels(andTDRstepswhenapplicable)of

supported two-channel electrical modules, to the module input connectors.
This application steps through the connection setup to align both the
acquisition and the TDR steps. For more information, see the help file for
the application.

The Differential Channel Alignment application is available for DSA8300
instruments running TekScope version 6.2.X and later, and legacy instruments
running TekScope version 5.2.x and later.

CAUTION. Always use the module ejectors to eject a module from a compartment.

Do not pull the module by the connectors; you can damage the connectors if you
use them to pull out a module.

1. Connect an antistatic wrist strap to the instrument front-panel ground
connection. Place the strap on your wrist.

2. Use the power cycle that is appropriate for your instrument:

ntial Channel Alignment application (Applications >

DSA8300 instruments with TekScope application version 6.1.X and

greater: Click Tools > View/Change Module Config and follow the
on-screen instructions.

Legacy instruments and DSA8300 with TekScope application version

6.0.X: Power off the instrument using the front-panel On/Standby switch.

3. Remove all cables or probes from the module connectors.

4. Turn the module lock screws counterclockwise until loose or they stop turning.

5. Push the module ejector lever to unseat the module. The arrow near an ejector

lever shows which compartment that ejector controls.

6. Use the module lock screws to pull the module partly out of the compartment.
Then hold the module chassis and pull the module from the instrument.

80A00 and 82A00 Sampling Modules Read This First 3