Tektronix 650-A900-00 Instruction Manual

Instruction Manual

650-A900-00 Preamplifier for the WCA200,
RSA200, RSA2200A, RSA3300A, and
RSA3400A series

WCA200/RSA200/RSA2200A/RSA3300A/
RSA3400A

зѪȼкᡑ

650-A900-00 ിїѪТѳї

075-1266-01

www.tektronix.com

075126601

Copyright © Tektronix, Inc. All rights reserved.

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supercedes that in all previously published material. Specifications and price change privileges reserved.

Tektronix, Inc., P.O. Box 500, Beaverton, OR 97077

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

Product Overview

The 650-A900-00 preamplifier is designed for use with the WCA200 series Wire­less Communication Analyzer, the RSA200, RSA2200A, RSA3300A,
RSA3400A series Real-Time Spectrum Analyzer.

The preamplifier has 100 MHz to 3 GHz frequency range and 20 dB gain. Power is
supplied to the preamplifier through the PRE AMP power connector on the front
panel of the WCA200, RSA200, RSA2200A, RSA3300A, or RSA3400A series
instrument. The WCA200, RSA3300A, and RSA3400A series have the power
connector on standard. The RSA200 and RSA2200A series need to add the power
connector with Option 06 and Option 2A, respectively.

Frequency characteristics and gain compensation data are provided with each in­strument. The data is provided as 3.5 inch floppy disk, you can install the data to the
WCA200, RSA200, RSA2200A, RSA3300A, and RSA3400A series. The instru­ment displays adjusted values, you need no additional data conversion.

Standard Accessories

H Power Cord (Tektronix part number: 012-A227-00)

Preamplifier power is supplied from the WCA200/RSA200/RSA2200A
/RSA3300A/RSA3400A series instrument.

H 3.5 inch floppy disk (Tektronix part number: 062-A293-XX)

Gain and frequency characteristics data is included.
Install this data to the WCA200/RSA200/RSA2200A/RSA3300A/
RSA3400A series.

H Certificate of Calibration

H Instruction manual (Tektronix part number: 075-1266-XX)

650-A900-00 Preamplifier Instruction Manual

1

Installation

Installation

NOTE. For the WCA230/280 and RSA230/280, the installation function is only
available for the instrument with firmware version 1.28 and above.

Do the following steps to perform the amplitude correction by using the provided
floppy disk. For detailed information on amplitude correction, refer to the user
manual for the WCA200, RSA200, RSA2200A,RSA3300A or RSA3400A series.

The 650-A900-00 preamplifier is designed to connect directly into the instrument
as shown in the figure below (the RSA200 and RSA2200A series need to add the
power connector with Option 06 and Option 2A, respectively).

1. Power off the instrument.

2. Install the 650-A900-00 preamplifier to the WCA200/RSA200/RSA2200A

/RSA3300A/RSA3400A series input connector. Turn the N-connector ring
when you install the preamplifier.

NOTE. Do not turn the body of preamplifier when you install it to the instru­ment. Take care not to place the connector too tight. Do not put a stress on the
amplifier body.

3. Attach the amplifier power cord.

4. Power on the instrument.

2

650-A900-00 Preamplifier Instruction Manual

Installation

5. Wait until operating system is loaded and the system is ready.

6. Press the front panel AMPLITUDE key.

7. Press the Correction... side key.

8. Insert the floppy disk (062-A293-XX) to the floppy disk drive of the

instrument.

For WCA230A/280A, RSA2203A/2208A, RSA3303A/3308A and RSA3408A

9. Press the Load Table side key. A file selection list appears.

10. Press the Folder side key and select the floppy drive (A:).

11. Press the Done side key.

12. Turn the rotary knob to select the amplitude correction file.

13. Press Load File Now side key to load the file.

14. After the loading, remove the floppy disk from the floppy disk drive.

15. Press Amplitude Table side key and select On.

The acquired data will be compensated and the waveform will be displayed. The
loaded data will be deleted if you press the AMPLITUDE

ʪ Correction... ʪ

Edit Table ʪ Clear Table side keys or simply press the PRESET key.

For WCA230/280 and RSA230/280

16. Press the Load side key. A file selection list appears.

17. Press the Change Directory side key repeatedly and select the amplitude

correction file from drive A.

18. Turn the rotary knob to select the amplitude correction file.

19. Press Enter side key to load the file.

20. After the loading, remove the floppy disk from the floppy disk drive.

21. Press Setup... side key.

22. Press Correction side key and select On.

The acquired data will be compensated and the waveform will be displayed. The
loaded data will be deleted if you press the AMPLITUDE
Edit... ʪ Reset side keys or simply press the PRESET key.

650-A900-00 Preamplifier Instruction Manual

ʪ Correction... ʪ

3

Specifications

Specifications

NOTE. Use this preamplifier only to small signals which are difficult to measure
with the analyzer. It is not recommended to use the preamplifier while
increasing the accuracy of instrument sensitivity.

DC input of preamplifier is permitted up to ±20 V. However, do not use the
amplifier as DC cutter.

You can order replaceable power cord (Tektronix part number: 012-A227-00)
when the cord damaged for any reasons.

Amplitude correction is available regardless of the use of preamplifier. Be sure
not to enable this function if you remove the preamplifier.

The 650-A900-00 preamplifier is used with the WCA200, RSA200, RSA2200A,
RSA3300A, or RSA3400A series, refer to the user manual for environmental spec­ifications.

Preamplifier Specifications

Environmental

Vibration

2

ȡȡNon–operating 490 m/s

total 18

(50 G), half sine, 11 ms duration, three times on each axis,

Power Source

Power Consumption Less than 2.4 W Maximum DC current 0.2 A (at +12 V)

Input Connector SMA-J type

Output Connector N-P type

Power Connector

ȡȡType LEMO 6 poles

ȡȡPin assignments Pin 1:GND, Pin 2:GND, Pin 3:GND, Pin 4:NC,

Pin 5:GND (common), Pin 6:+12 V

Electrical Specifications

Frequency range 100 MHz to 3 GHz

Small signal gain 19 dB to 24 dB at 2 GHz

Gain flatness ±3.0 dB 100 MHz to 3 GHz (without correctionɋ

±1.0 dB 100 MHz to 3 GHz (with correction) *

Noise figure ≤6.5 dB 2 GHz *

Noise floor ≤–160 dBm/Hz 2 GHz (with WCA200 series) *

Output power ≥+6 dBm at 1 dB Compression, 2 GHz *

Harmonics ≤–50 dBc at +4 dBm output power, 1 GHz *

4

650-A900-00 Preamplifier Instruction Manual

Specifications

Third order Intermodula­tion distortion

Signal input

ȡȡVSWR <2.2 at 100 MHz to 150 MHz *

ȡȡMaximum input DC
ȡȡvoltage

ȡȡMaximum input
ȡȡpower

Signal ouput

ȡȡVSWR <2.2 at 100 MHz to 150 MHz *

≤–45 dBc
at Total signal power=+4 dBm output power, CF=2 GHz *

<1.8 at 150 MHz to 3 GHz*

±20 V

+13 dBm

<1.5 at 150 MHz to 2.5 GHz *

<2.2 at 2.5 GHz to 3 GHz *

* Typical.

Mechanical Specifications

Weight 0.2 kg

Dimensions (Without a cap)

ȡȡWidth 32 mm

ȡȡHeight 108 mm

ȡȡDepth 42 mm

Cooling Required clearances

ȡȡTop 2.5 cm

ȡȡLeft side 2.5 cm

ȡȡRight side 2.5 cm

ȡȡRear 2.5 cm

650-A900-00 Preamplifier Instruction Manual

5

Specifications

6

650-A900-00 Preamplifier Instruction Manual

ᆽᙊଵᡗ

ТЯлеѪ

650ĆA900Ć00ĂിїѪТѳїϏȢWCA200ĂзѪȼкڥѯФѤѬйڥгџѥыбȼзѧѳڥТъ
ѩФжȢΪϨϓĂRSA200ȢRSA2200AȢRSA3300AȢRSA3400AзѪȼкڥѪТѫпФѠڥй
њЯшѩѠТъѩФжψቈϟ๧ϯλφ཈ᡑιϫїѪТѳїχιȣ

їѪТѳїώ࿾ᕈᅴዓ২ϏĂ100ĂMHzɁ3ĂGHzȢвФѳϏ៳20ĂdBĂχιȣᑅරϏȢWCA200
зѪȼкϞοϏĂRSA200/RSA2200A/RSA3300A/RSA3400AĂзѪȼк᝜ዎሰ៌ёэѫώ
ĂPREĂAMPĂᑅරгэЯпΫϩಡ౫εϬϞιȣWCA200ĂзѪȼкψĂRSA3300AĂ/RSA3400A
зѪȼкϏȢᑅරгэЯпϲᘸၠχትᗷηφΤϞιȣRSA200ĂзѪȼкχϏЪїзѧѳ

Ă06ȢRSA2200AĂзѪȼкχϏЪїзѧѳĂ2AĂχȢᑅරгэЯпϲᏉૃιϫᘬᡗά΢ϪϞιȣ

650ĆA900Ć00ĂിїѪТѳїϋϏȢ1Ăዦδψϋ࿾ᕈᅴᓃᆭȢвФѳώᛤᆵчȼпάѕѭуєȦ

чУйЯχᐺᙕεϬφΤϞιȣWCA200/RSA200/RSA2200A/RSA3300A/RSA3400AĂзѪȼ
кώ᝜ዎϋФѳйшȼѫιϫγψχȢїѪТѳїώᛤᆵ෥ώᘽྨάϊεϬϫοϡȢኬᏪፍώ
ஹ༻άᙔᡗϋϊϪϞιȣ

650ĆA900Ć00ĂിїѪТѳїϋϏȢྡώТЯлеѪάᙕኰηφΤϞιȣ

H ᑅරбȼіѫɊᙴᙊᗖ๦ȧ012ĆA227Ć00ɋ

WCA200/RSA200/RSA2200A/RSA3300A/RSA3400AĂзѪȼкΫϩїѪТѳїϋᑅර

ϲಡ౫ηϞιȣ

H 3.5ĂിѕѭуєȦчУйЯɊᙴᙊᗖ๦ȧ062ĆA293ĆXXɋ

вФѳΪϨϓ࿾ᕈᅴᓃᆭώчȼпάభ᤿ηφ΢ϪϞιȣ
WCA200/RSA200/RSA2200A/RSA3300A/RSA3400AĂзѪȼк᝜ዎϋФѳйшȼѫη
φ཈ᡑηϞιȣ

H ฻ᆵლៀၱ

H ФѳйшѩЯзѧѳȦўыѥТѫȧ᝜ၱɊᙴᙊᗖ๦ȧ075Ć1266ĆXXɋ

ᓼ᝜෬ψ෬χభໜεϬφΤϞιȣ

WCA200/RSA200/RSA2200A/RSA3300A/RSA3400AзѪȼкᡑїѪТѳї

1

ФѳйшѬȼзѧѳ

ФѳйшѬȼзѧѳ

፭ȧФѳйшѬȼзѧѳడᔽϏȢWCA230/280ĂിΪϨϓĂRSA230/280Ăിώწ๧Ȣ᝜ዎώ

ѕСȼѠЦЧТȦѐȼиѧѳάĂ1.28Ă৊ქώཾϋώϟ཈ᡑχέϞιȣ

ᙕኰώѕѭуєȦчУйЯϲ཈σφᄶᙽᛤᆵϲ๔ΦϋϏȢ઼భώ࿪ၧϋှσφίπεΤȣ
ᄶᙽᛤᆵώნ໙ϋτΤφϏȢѦȼжȦўыѥТѫȧɖѪѕСѬѳйɗώ჏ϋ΢ϫɖ࿾ᕈᅴȢ
йёѳȢΪϨϓᄶᙽώᇟᏪɝᄶᙽᛤᆵɗϲ༲჈ηφίπεΤȣ

650ĆA900Ć00ĂിїѪТѳїϏȢWCA200/RSA200/RSA2200A/RSA3300A/RSA3400AĂзѪȼ
кώ᝜ዎϋᎾᇜት፥ηφ཈ᡑηϞιɊRSA200ĂзѪȼкχϏЪїзѧѳĂ06ȢRSA2200AĂз
ѪȼкχϏЪїзѧѳĂ2AĂχȢᑅරгэЯпϲᏉૃιϫᘬᡗά΢ϪϞιɋȣ

1. ᝜ዎώᑅරϲЪѕϋηϞιȣ

2. 650ĆA900Ć00ിϲĂWCA200/RSA200/RSA2200A/RSA3300AĂ/RSA3400AзѪȼкώᓾᣏ

гэЯпϋ࿨ϪᙕαϞιȣNĂгэЯпώѪѳаϲ૳ᐾελφ࿨ϪᙕαφίπεΤȣ

፭ȧїѪТѳї᝜ዎϲ૳ᐾελφĂNĂгэЯпϲᏹϡϊΤχίπεΤȣϞοȢгэЯпώᏹ
ϡιήȢνώኾώйшѬйϲᠿΨϊΤχίπεΤȣ

3. ᑅරбȼіѫϲ࿨ϪᙕαϞιȣ

4. ᝜ዎώᑅරϲᑪᓾηϞιȣ

5. ᝜ዎώĂOSĂάᢩქϪȢᒰ໮ჵዖϋϊϫώϲዔρϞιȣ

2

WCA200/RSA200/RSA2200A/RSA3300A/RSA3400AзѪȼкᡑїѪТѳї

ФѳйшѬȼзѧѳ

6. ሰ៌ёэѫώ AMPLITUDE ЭȼϲડηϞιȣ

7. Correction... еФщȦЭȼϲડηϞιȣ

8. ѕѭуєȦчУйЯĂ(062ĆA293ĆXX)Ăϲడ௯ώѕѭуєȦчУйЯȦщѩФіϋ቞ᓾη

Ϟιȣ

WCA230A/280AĂിȿRSA2203A/2208AĂിȿRSA3303A/3308AĂിȿRSA3408Aിώწ๧

9. Load Table еФщȦЭȼϲડηϞιȣѕСФѫሪዲ૨៌άᘽྨεϬϞιȣ

10. FolderĂеФщȦЭȼϲડηȢѭȼпѪȦюіϲ૳ηφĂ3.5ĂФѳсĂFDĂ(A:)ĂϲሪዲηϞιȣ

11. DoneĂеФщȦЭȼϲડηϞιȣ

12. ѭȼпѪȦюіϲ૳ηφȢᄶᙽᛤᆵѕСФѫϲሪዲηϞιȣ

13. Load File NowĂеФщȦЭȼϲડηφȢѕСФѫϲᓉϟ๾ϟϞιȣ

14. ѕСФѫώᓉϟ๾ϟάரᢻηοϩȢѕѭуєȦчУйЯȦщѩФіΫϩѕѭуєȦ

чУйЯϲ࿨ϪၐηϞιȣ

15. Amplitude TableĂеФщȦЭȼϲડηφȢOn ϲሪዲηϞιȣ

࿨Ϫ๾ϳπчȼпϋዐηφᄶᙽᛤᆵάΫαϩϬȢᕈുάᘽྨεϬϞιȣᓉϟ๾ϳπᛤᆵ
чȼпϲჃ౮ιϫწ๧ϏȢAMPLITUDE ʪ Correction... ʪ Edit Tableʪ Clear Table еФщ
ЭȼϞοϏĂPRESET ЭȼϲડηϞιȣ

WCA230/280ĂിȿRSA230/280Ăിώწ๧

16. Load еФщȦЭȼϲડηϞιȣѕСФѫሪዲ૨៌άᘽྨεϬϞιȣ

17. Change DirectoryĂеФщȦЭȼϲિ૳ΫડηφȢщѩФіĂA:ĂώᄶᙽᛤᆵѕСФѫϲ

ሪዲηϞιȣ

18. ѭȼпѪȦюіϲ૳ηφȢᄶᙽᛤᆵѕСФѫϲሪዲηϞιȣ

19. Enter еФщȦЭȼϲડηφȢѕСФѫϲᓉϟ๾ϟϞιȣ

20. ѕСФѫώᓉϟ๾ϟάரᢻηοϩȢѕѭуєȦчУйЯȦщѩФіΫϩѕѭуєȦ

чУйЯϲ࿨ϪၐηϞιȣ

21. Setup... еФщȦЭȼϲડηϞιȣ

22. Correction еФщȦЭȼϲડηφȢOn ϲሪዲηϞιȣ

࿨Ϫ๾ϳπчȼпϋዐηφᄶᙽᛤᆵάΫαϩϬȢᕈുάᘽྨεϬϞιȣᓉϟ๾ϳπᛤᆵ
чȼпϲჃ౮ιϫწ๧ϋϏȢAMPLITUDE ʪ Correction... ʪ Edit... ʪ Reset еФщȦЭȼ
ϞοϏĂPRESET ЭȼϲડηϞιȣ

WCA200/RSA200/RSA2200A/RSA3300A/RSA3400AзѪȼкᡑїѪТѳї

3

༲ํ/፭৕

༲ํ/፭৕

ཅᡍ

1. їѪТѳїϏȢWCA200/RSA200/RSA2200A/RSA3300A/RSA3400AзѪȼк᝜ዎπα
χϏኬᏪηϋίΤᗹႮᄮ๦ϋώϟ཈ᡑηφίπεΤȣ᝜ዎώஶᑙϲ๊σφїѪТѳї
ϲᚻᡑιϫ཈ᡑᜡϏϊϫϙίᗲαφίπεΤȣ

2. їѪТѳїώĂDCĂᓾᣏϏĂɞ20ĂVĂϞχ౶ᡆεϬϞιάȢDCĂЫупψηφ཈ᡑηϊΤχ
ίπεΤȣ

3. ᑅරбȼіѫάၽϳπწ๧ϋϏȢጱዎώёȼфψηφᖯ፭ιϫγψάχέϞιȣᙴᙊ
ᗖ๦ϋτΤφϏȢ1ĂњȼиώɖТЯлеѪɗϲ༲჈ηφίπεΤȣ

4. ᄶᙽᛤᆵడᔽϏȢїѪТѳїώ཈ᡑϋ௘സϊίᒰ໮ηϞιȣїѪТѳїϲରηοϩȢ
ᛤᆵడᔽϲЪѕϋιϫϨΦ፭৕ηφίπεΤȣ

їѪТѳїϏȢWCA200/RSA200/RSA2200A/RSA3300A/RSA3400AĂзѪȼкϋᇜኳηφ཈
ᡑιϫοϡȢ௄ಭᓃᆭϊωϏȢWCA200/RSA200/RSA2200A/RSA3300A/RSA3400AзѪȼ
кώཅᡍϋၠ౲ηϞιȣ

௄ಭᓃᆭ

ᓃᆭ బ୊

თൢ

2

ȡȡᗳᒰ໮ཾ 490m/s

୆ྴ᛽෾3૳Ɋሴ18૳ɋϋዑΨϞιȣ

ɐ50GɑȢ1/2ᆵඹᕈȢ11msώཽኳཾ௖Ȣ

ᘬᡗჲ൯

ᓃᆭ బ୊

ᔮჃᗱ໇ዧ2.4Wȡ໇ዧ DC ᑅ᢮ 0.2AɊ+12V ཾɋ

᛼ᔮᡑЯѪТѩѳй

ȡȡქᙴ 2.5cm

ȡȡຸ 2.5cm

ȡȡ෥ᙴ 2.5cm

ᑅර

ȡȡᑅ঵ +12VDC

ɊWCA200/RSA200/RSA2200A/RSA3300A/RSA3400AĂзѪȼ
кϨϪಡ౫ɋ

ȡȡ໇ዧᑅ᢮ 0.2A

ȡȡ໇ዧᑅᣏ 2.4W

ᓾၐᣏгэЯп

ȡȡRFᓾᣏ SMAിиѣуЯ

ȡȡRFၐᣏ Nിїѩа

ᑅරгэЯп

4

WCA200/RSA200/RSA2200A/RSA3300A/RSA3400AзѪȼкᡑїѪТѳї

ȡȡгэЯпώ࿯ᣠ LEMO 6ೋ

ȡȡєѳώ୤Ϫᑶφєѳ1: GNDȢєѳ2: GNDȢєѳ3: GNDȢєѳ4: NCȢ

єѳ5: GNDɊгѢѳɋȢєѳ6: +12V

ᑅతᐪᓃᆭ

ᓃᆭ బ୊

࿾ᕈᅴᗏ৏ 100MHzɁ3GHz

вФѳ 19Ɂ24dBȡ2GHz

ѕѩушэй ɞ3.0dBȡ100MHzɁ3GHzɊᛤᆵ឵ηɋ

ɞ1.0dBȡ100MHzɁ3GHzɊᛤᆵ෥ɋȡ

༨઻མᅴ ɥ6.5dBȡ2GHzȡ

ɶ

юФкȦѕѭТ ɥ–160dBm/Hzȡ2GHz

ɊWCA200зѪȼкψቈϟ๧ϯλοწ๧ɋȡ

1dB঵၌ၐᣏѬљѫ ɦ+6dBmȡ2GHzȡ

ɶ

๢Ꮄᕈ᥄ϟ ɥ–50dBcȡ1GHzȡၐᣏ +4dBmȡ

3ྡቪෟᛑᎴ᥄ϟ ɥ–45dBcȡቭᄮ๦ၐᣏ=+4dBmȢCF=2GHzȡ

ᄮ๦ᓾᣏ

ȡȡVSWR <2.2ȡ100MHzɁ150MHzȡ

<1.8ȡ150MHzɁ3GHzȡ

ɶ

ɶ

ȡȡ໇ዧᓾᣏDCᑅ঵ ɞ20V

ȡȡ໇ዧᓾᣏᑅᣏ +13dBm

ᄮ๦ၐᣏ

ȡȡVSWR <2.2ȡ100MHzɁ150MHzȡ

<1.5ȡ150MHzɁ2.5GHzȡ

<2.2ȡ2.5GHzɁ3GHzȡ

ɶ

ዥᘽፍ

ɶ

ɶ

ɶ

ɶ

ɶ

ɶ

ɶ

ཅᡍ

డଣᐪᓃᆭ

ᓃᆭ బ୊

࿁ᣌ ៳ 0.2kg

ᆣᜡɊЭѣуїϲ௞ϞϊΤɋ

ȡȡᙽ 32mm

ȡȡ๢ε 108mm

ȡȡ๔έ 42mm

WCA200/RSA200/RSA2200A/RSA3300A/RSA3400AзѪȼкᡑїѪТѳї

5

ཅᡍ

6

WCA200/RSA200/RSA2200A/RSA3300A/RSA3400AзѪȼкᡑїѪТѳї