Tektronix 644-1095-01 Field Install Instructions

xx
644-1095-01 Rackmount Kit
ZZZ
for the TSO820 and TCR801
Installation Instructions
www.tek.com
$
Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc. 14150 SW Karl Braun Drive P.O. Box 5 0 0 Beaverto USA
For product information, sales, service, and technical support:
n, OR 97077
In North America, call 1-800-833-9200. Worldwide, visit www.tek.com to find contacts in your area.
General safety
summary
Review the following safety precautions to avoid injury and prevent damageto this product or any products connected to it.
To avoid potential hazards, use this product only as specified.
Only qualied personnel should perform service procedures.
To avoid damage to
equipment and personal
injury
Contacting Tektronix
Do not exceed rackmount weight ratings. Use this rackmount kit only for TSO820
and TCR801 instruments.
Use proper hardware. Do not interchange hardware. Use only specified mounting screws.
Use care when installing and removing product from rack. Avoid pinching fingers and hands when installing and removing. Do not force the product when
ng. Gently pull the product out when removing.
installi
Use only with specied products. Do not use rackmount on products for which it was not intended. Refer to individual product manuals for details or contact Tektronix Customer Service when in doubt.
Tektronix, Inc. 14150 SW Karl Braun Drive P.O. Box 500 Beaverton, OR 97077 USA
For product information, sales, service, and technical support:
In North America, call 1-800-833-9200.
Worldwide, visit www.tek.com to find contacts in your area.
Tektronix 8 Series Rackmount Kit Installation Instructions 1
Kit description
Kit description
The 3U rackmount kit is a collection of parts that, once installed, configures the following Tektronix products for mounting into a standard 19-inch equipment rack.
Products
TSO820
TCR801
Required equipment
Phillips #2 screwdriver
11/32 socket or nut driver
Torx driver for bits
Torx T-8 b it
Torx T-15 bit
Torx T-20 bit
Kit parts list
The following table lists the parts contained in this kit. The figure shows the contents of the kit. The slides and rails come attached to the tray. A bag of hardware (screws) is included.
Table 1: 8 Series rackmount kit parts list
Qty. Description Tektronix part number
1
TRAY, BASE, RACKMOUNT
2
HANDLE, BOW
2
ASSEMBLY, SLIDE AND RAIL
with the following hardware installed:
8
8 NUT,KEP,8-32 NA
4
8
1
1
1
1
1
SCREW, MACHINE 8-32x .375
SCREW, MACHINE 6-32x .312
SCREW, MACHINE 8-32x .265
BRACKET, RACK, LEFT, FRONT
BRACKET, RACK, LEFT, REAR
BRACKET, RACK, RIGHT, FRONT
BRACKET, RACK, RIGHT, REAR
Small bag containing:
407-6199-xx
367-0562-xx
351-1147-xx
NA
211-1050-xx
212-0283-xx
407-5596-xx
407-5597-xx
407-5598-xx
407-5599-xx
2 Tektronix 8 Series Rackmount Kit Installation Instructions
Table 1: 8 Series rackmount kit parts list , (cont.)
Qty. Description Tektronix part number
12
16
8
SCREW, MACHINE 10-32x .625
SCREW, MACHINE 8-32x .265
SCREW, MACHINE 6-32x .312
212-0577-xx
212-0283-xx
212-0004-xx
Kit description
Tektronix 8 Series Rackmount Kit Installation Instructions 3
Kit description
Installation
Install the rackmount into
the rack
This rackmount comes completely assembled with slide rails in place. Before securing the rack rails on a rack, you will need to remove them from the tray assembly.
1. Remove the rack rails from the tray assembly:
a. Slidearackrailcompletelytotherear(awayfromtrayhandles)untilit
stops and exposes the rail release tab located on the inside of the rail.
b. Depress the release tab (1) and continue to slide the rack rail until it is
detached from the tray assembly. (You may need to use a thin metal rod
w driver to depress the tab.)
or scre
c. Repeat steps a through b for the other rack rail.
4 Tektronix 8 Series Rackmount Kit Installation Instructions
Kit description
2. Loosen the cent adjustment.
3. Attach the rack rails to the rack, ensure that the rack rail ends marked FRONT and REAR are appropriately aligned to the front and rear of the rack:
a. Use 2 screws (212-0577-xx) and a Phillips head driver to anchor a rack
rail to the rack front (3) (flanges facing out).
er screws (2) of each rack rail to allow for later rail length
b. Push the rack rails into the rack frame and then tighten the screws.
c. Use 2 screws (212-0577-xx) to anchor the rack rail to the rack rear.
Tektronix 8 Series Rackmount Kit Installation Instructions 5
Kit description
To install one or two
TSO820 or TCR801
d. Adjust the gree
e. Hold the center nuts and tighten the center screws to secure the rack rail.
f. Repeat steps a through e for the other rack rail.
If you are only inserting one instrument, you can place it in the center (triangles), right (squares), or left (circles) side of the tray.
n rail stops as far backward as possible.
4. Install the instrument(s) into the tray assembly:
a. If you are installing a TSO820 in the right side of the tray, first remove
the right side handle of the instrument (right rail side) with a T-20 tip and
river. The instrument will not fit with the handle on. You do not need to
d remove any handles in the other placement configurations.
6 Tektronix 8 Series Rackmount Kit Installation Instructions
Kit description
b. Place the four f
of the tray. Ensure the feet settle into the cutouts and the bottom of the instrument is flush with the tray.
eet fit into the rectangular cutouts at the front and rear
c. Yo u n
Tektronix 8 Series Rackmount Kit Installation Instructions 7
eed to secure the instrument to the tray from the bottom. Do this by rotating the tray on the table to expose each corner with one foot and its adjacent screw hole hanging off of the table. Secure each corner in turn using a T-20 screws [212-0004-xx].
Kit description
d. Check that the i
e. Install a second instrument, if desired.
5. Slide the tray with installed instruments into the rack rails as follows:
a. Insert the tray with installed instrument(s) into the installed rack rails.
Once the tray clicks into place, depress both of the release tabs at the same time and slide the tray completely backward.
nstrument is secure.
b. Push in
rack along the slide-rails. Push until the entire tray is in the rack.
NOTE. If the tray will not push fully into the rack, rst check that the green
rail stops are pushed as far backward as possible. You can also check to ensure that the rail screws a re not blocking the tray. If they are, adjust them accordingly.
6. (Optional) Add 4 more screws (212-0577-xx) to lock the rack rails in place.
both release tabs at the same time while pushing the tray into the
8 Tektronix 8 Series Rackmount Kit Installation Instructions
Loading...