Tektronix 065-0768-02 User manual

065-0740-XX
Hard Disk Drive Assembly
Without Software
For CSA7000B, TDS7000B,
TDS6000B&Cand
TDS5000B Option FHD
Instructions

This assembly can be used for either the front
hard drive or the rear hard drive instruments.

Table 1: Hard drive covers

Instrument Need covers?

TDS/CSA7000B
with rear hard drive (Std
configuration)

with front hard drive
(option FHD)

TDS6000B
with both front and rear
hard drives

TDS6000C
with both front and rear
hard drives

TDS5000B
with front hard drive
(option FHD)

1

No additional cover assembly is required for
TDS/CSA7000B instruments with the standard rear
hard drive location; discard all covers. Install the hard
drive assembly as shown in Figure 2 on page 2 and
proceed to Load Software.

1

No
(assembly is ready to
install into the scope.)

Yes
use cover 200-4830-XX.

Yes
use cover 200-4890-XX.

Yes
use cover 200-4967-XX.

Yes
use cover 200-4848-XX.

Use the following procedure to prepare the
assembly for your instrument.

1. Remove the thumb screws from the hard
drive.

2. Slide the appropriate hard drive cover for
your instrument onto the hard drive
assembly. See Figure 1.

Table 1 lists the appropriate covers for each
instrument type.

3. Install the thumb screws.

4. The assembly is ready to install in your
instrument. See Figure 2 on page 2.

Load Software

After assembling and installing the hard drive
assembly into the instrument, follow the
installation procedures in the system, product,
and application software booklets to load the
appropriate software onto the new hard drive in
your instrument.

After loading the software, Tektronix
recommends that you run the Windows
Defragmenter on your hard drive.

www.tektronix.com

*P071151902*

071-1519-02

Assembly Description

This document supports the Tektronix Hard Disk
Drive Assembly 065-0740-XX used in
CSA7404B, TDS7704B, TDS7404B,
TDS7254B, TDS7154B, TDS6604B,
TDS6804B, TDS6124C, TDS6154C and
TDS5000B Series (Option FHD) instruments.

Effective for all above products: serial numbers
B010100 and above.

Minimum Tool and Equipment List

None required.

Assembly Installation

These instructions are for personnel who are
familiar with servicing the product. If you need
further details for disassembling or reassembling
the product, refer to the appropriate product
manual. Contact your nearest Tektronix, Inc.,
Service Center or Tektronix Factory Service for
installation assistance.

Alignment tabs

Tab

Hard drive cover

Note: The TDS5000B
FHD cover installs from
the bottom up instead of
top down as shown for
the other models.

Thumb screws (2)

CAUTION. To prevent static discharge

damage, service the product only in a
static-free environment. Observe standard
handling precautions for static-sensitive
devices during installation. Always wear a
grounded wrist strap, grounded foot strap,
and static resistant apparel during
installation.

Copyright E Tektronix, Inc. All rights reverved

Figure 1: Attaching a cover

Removable hard-drive

assembly

(065-0740-XX

)

Figure 2: Reinstalling the hard drive

Tighten the

thumbscrews

Push the hard disk drive

straight in

Contacting Tektronix

Tektronix, Inc.
14200 SW Karl Braun Drive
PO Box 500
Beaverton, OR 97077
USA

For product information, sales, service, and
technical support:

H In North America, call 1--800--833 --9200.

H Worldwide, visit www.tektronix.com to find

contacts in your area.

Safety Summary

To avoid potential hazards, use this product only
as specified.

Only qualified personnel should perform service
procedures.

To Avoid Fire or Personal Injury

Do Not Operate Without Covers. Do not operate

this product with covers or panels removed.

Avoid Exposed Circuitry. Do not touch exposed

connections and components when power is
present.

Do Not Operate With Suspected Failures. If you

suspect there is damage to this product, have it
inspected by qualified service personnel.

Do Not Operate In Wet/Damp Conditions.

Do Not Operate In An Explosive A tmosphere.

Keep Product Surfaces Clean and Dry.

Provide Proper Ventilation.

installation instructions for details on installing
the product so it has proper ventilation.

Refer to the manual’s

Warranty Information

For warranty information, go to
www.tektronix.com, click Support, and then use
the provided links to search for your product’s
warranty.

Copyright © Tektronix, Inc.

Beaverton, OR 97077