Teknim ATP545, ATP545P, ATP545LR Installation And User Manual

ATP545 Digital Passive Infrared Detector

Infrared sensor

Dual element, Digital

Alarm period

3 sec.

Power requirement

9 ~ 16 VDC, 20mA

Alarm output

N.C 30VDC, 0.2A max.

Sensitivity setting

With trimpot

Pulse count

3 modes, 1, 2, 3

Tamper

N.C (cover open and wall
removal activated)

Activation LED

Red, can be disable

Detectable speed

0.3 ~ 1.5m/sec.

Pet Immunity

20 kg, 60cm (ATP545P)

Mounting height

For all model 2.1 ~ 2.5m

Humidity

95% RH (max)

Temperature

-20C ~ 45C (-4F ~ 113F)

Dimensions

108 X 63 X 50 mm

Weight

80 gr

Temperature
compensation

Yes

Connections
Pulse jumper

LED on/off jumper

Tamper switch
Infrared sensor

Activation LED

Sensitivity setting

ATP545P Pet-Immune Digital Passive Infrared Detector
ATP545LR Long Range Digital Passive Infrared Detector

Installation and User Manuel

Issue Date: 05/02/2016

TECHNICAL SPECIFICATIONS

CABLE CONNECTIONS

Insert the PCB to it’s place and connect the signal cables

related points.

POWER
ALARM : Control panel zone input (N.C)
TAMPER : Tamper switch contacts (NC)

: 9 ~ 16 VDC power supply



Technical specifications may be changed without
notification.

COMPONENTS

SENSITIVITY SETTING

ATP545 series PIR detectors have the sensitivity setting with
trimpot For adjusting, use a thin screwdriver.

Sensing dis. for ATP545 Digital Passive Infrared Detector
Sensing distance when SENS Pot is lowest pos. : 8m

Sensing distance when SENS Pot is center pos. : 12m
Sensing distance when SENS Pot is highest pos. : 14m

PULSE SETTING

Warning:

Do not touch to the Infrared sensor

MOUNTING

For ATP545P, it must be mounted to 2.1-2.5m height
wall without mounting foot for correctly running pet
immunity feature.

WARNING!

ATP545 series PIR detectors have pulse setting with 3 levels
(1, 2, 3)

ACTIVATION LED SETTING

Set to “OFF” mode, if you do not want that LED is off when
the detector detects any moving.

DETECTION AREA

Bilgi Elektronik A.Ş.
Address :

Dudullu Organize Sanayi Bölgesi 1. Cadde İsmet Tarman İş
Merkezi No:1 Kat:2 No:32 Ümraniye/İstanbul

Tel: [phone] Fax: [phone]

www.bilgielektronik.com.tr

Sales: [e-mail]
Technical Support: [e-mail]

ATP545N
110 14m ( 25C) Top View

Side View

ATP545P
90 10m ( 25C) Top View

Side View

ATP545LR
75 20m ( 25C) Top View

 Do not mount the detector next to the devices which

cause to instantaneous temperature alternation.

 Mount the detector recommended height and to the

strong surface.

 Please note that PIR detector is more sensitive to

horizontal movements.

 Do not touch the sensor, for cleaning use alcohol cotton

MALFUNCTIONS THAT REQUIRE TECHNICAL
SERVICE

In case of any malfunction or below conditions contact with
your authorized service,

 When Mains cable or the plug is harmed,
 Contact of device with a fluid,
 Exposure of rain and water,
 Fell down of device or harmed outer cover,
 Serious performance fall on the device,
 Depending on the instructions stated in manual, if your

device not working properly, further usage or possible
wrong usage may cause other malfunctions . Contact with
your authorized service in such terms.

SPARE PART

If the repair will be done by spare parts, to avoid fire,
electricity shock or any other hazardous conditions, Make
sure your service is using original parts or parts compatible
with your equipment.

SAFETY CHECK

To make sure if your device working properly and in safe
conditions or not, demand service from your dealer to check
device functionality.

TRANSPORTATION

Device must be carefully transported avoiding all physical
bump, stroke and possible fluid entry. Malfunctions that
caused by improper transportation is not under warranty.

HUMAN AND NATURE CONDITION

This device contains no chemical or biological elements that
could harm human condition.

MAINTENANCE ON YOUR OWN

Do not try to fix the device on your own, removal of cover
may end up with electricity shock.

In case of any defect or malfunction, contact with your dealer
or with authorized service. All the technical interventions has
to be done by technicians of service company. Device must
be cleaned up with a dry fabric. No-chemicals are allowed for
cleaning.

Side View

WARNINGS

 Do not expose the detector to direct or reflected light.
 Be sure that view angle is not prevented by any obstacle.

MANUFACTURER