Tekk International XV-100 Series, XU-100 Series User Manual

This device complies with Part
15 of FCC Rules.
Operation is subject to the
following two conditions:

This device may not cause
harmful interference, and 2)
This device must accept any
interference received, including
interference that may cause
undesired operation.

XU/XV-100

Series

User Manual

XU/XV-100

Series

User Manual

Printed in Korea. 200808

www.Tekk-Radios.com

▶▶▶▶▶▶▶▶▶▶▶▶

1. Precautions

2. Features

3. Appearance of XU/XV-100 Series Radio

4. Operating XU/XV-100 Series Radio

5. Basic Operation of XU/XV-100 Series Radio

6. Charging the Battery

7. Operating Instructions of XU/XV-100 Series Radio

1
2
3
4
5
6
8

Table of Contents

Thank you for your purchase of the XU/XV-100 Series Radio.

1. When using the Radio, please read the enclosed user guide in details.

2. The functions and specifications are subject to be changed without notice for
improvement of the Radio performance.

Components could be changed by buyer request.

Radio

Belt Clip User Manual

Battery Pack

Antenna

Adaptor/Charger

www.Tekk-Radios.com

2. Features

The XU/XV-100 Series Radio is developed to be user friendly, compact design and light
weight and to have the similar communication range to the industrial Redio and the Radio is
suitable for leisure and women due to much lighter weight compared with the other Radios.

The followings are the main features of the XU/XV-100 Series Radio.

2

Don’t remove the antenna from the Radio or don’t transform the antenna or
don’t make any change on the antenna. The strong electronic wave to be
emitted from the Radio can have an effect on the performance of the Radio and
can cause the Radio to have a defect.

In case of the area that medical equipments are being used, please use the
Radio after discussion with the equipment maker or the related doctor.

Don’t disassemble or reorganize the Radio. The disassembly or reorganization
will be causes of defect or malfunction and it will be impossible to make repair
afterward. Also, a punishment can be made by law.

Don’t use the other frequency except for the permitted frequency in order not to
be punished by law.

Don’t give an excessive shock to the Radio.
Don’t place the Radio where the direct sunlight and/or the high temperature
occurs.
If the Radio is placed for a long time in car in summer, the hot temperature in
the car may cause an explosion of battery.
Sharp substance and/or an excessive shock may cause damage to the battery.

Please don’t use the Radio at the place where computer or other electric /
electronic devices are being used, because the strong electronic wave from the
Radio can have an effect on the equipments.

Please keep the Radio away at least 1inch from the body.
If the outside surface of antenna gets stripped out, it can make a burn on the
skin.
If you contact a conductive metal to battery terminal, a heat can be made and
it may cause fire, explosion and burn. Especially, please be careful when
putting the battery in a pocket or a bag.
When using an earphone, please don’t listen to the sound at a high level.
The high sound may have a bad effect on your ear.

16 Groups and 128 Channels are selectable.
Call guard Squelch of standardized 53 CTCSS / 208 DCS
Frequency inverter type of Scramble function
Compander function
Dual Tone Modulation Frequency (DTMF)
Normal Scan / Priority Scan
VOX
2 Tone / 5 Tone
BCL / BCLO
Time-Out Timer (TOT)
Monitor
1Watt Speaker Power
PLL synthesizer type
DC+3.7V Li-ion/ 1,800 mAH high capacity Battery
5 step Squelch control using RSSI.
Lone Worker
Remote Radio Stun / Unstun(Use 5 tone)
Cloning function
Pc Programing cable in USB type

www.Tekk-Radios.com

figure 3-1) Appearance of XU/XV-100 Series Radio

figure 3-2) XU/XV-100 Series LCD Indication

Battery Pack

Battery Locker

Antenna Connector

On/Off/

Volume control

RX/TX LED

Monitor Button(M)

Menu Button(P)

Belt Clip

PTT Button

Antenna

Accessory
Connector

On/Off/

Volume control

5 Tone

Alert

2 Tone

RSSI

Channel & Status

Key Lock

Scramble

Compander

Battery Level Indicator

VOX

CTCSS & DCS

Priority SCAN & Normal SCAN

Down Button(▼) Enter Button( ) Up Button(▲)

1. On/Off/Volume Control

Turns the radio on and off and adjusts audio volume level.

2. PTT Button(Push-To-Talk Button)

Radio transmission button. It is recommended to talk 5~10cm away from the micro phone for
the best voice communication.

3. Menu Button(P, Program Menu Button)

Enter into Menu mode by pressing the Menu button (P) for 2 seconds.
The sequence of menu mode is as follows.

4. Monitor Button(M)

The monitor mode is enabled and disabled by pressing the Monitor button (M) on the side.
Normal Mode : During pressing the Monitor button(M) for about 2 seconds, it is possible to
check the receiving status.
Continuous Mode : During pressing the Monitor button(M) for more than 2 seconds, the
Radio will make a “Beep” tone, which means the monitor function is maintained and if you
press the Monitor button(M) again, the monitor function will be released.

5. Channel Buttons( ▼,▲)

Channel Buttons(▼,▲) have 2 functions as shown in following.
①Channel buttons(▼,▲) are to change channels.
②Channel buttons(▼,▲) are to select menu at menu mode.

6 Accessory Connector

The Accessory Connector is used when using an external speaker microphone or doing
PC programming or making the Cloning or using as a Repeater.

7. RX /TX Led

This LED is a lamp indicating the current status of the Radio and please refer to the below
contents.

①RX : Green Lamp.
②TX : Red Lamp.
③CTCSS, DCS Error : Green Blinks.

Compander → Change Group → ID → Scramble → Squelch

→ KEY Sound → VOX → Lone Worker

→→→→

→→→

www.Tekk-Radios.com

5. Basic Operation of XU/XV-100 Series Radio

6. Charging the Battery

figure 5-2) Installation and

Removal of the Battery

figure 5-3) Installation and Removal of

the Belt Clip

figure 5-1) Installation and Removal of the Antenna

When installation of the antenna, giving a strong pressure to the Radio or pulling
the antenna with a strong power from the Radio can make a damage on the
antenna connector, which may cause the Radio to have a critical problem.

▶5.2 Installation and Removal of the Battery

5.2.1 Installation of the battery

To install battery, slide up the battery towards
the top of the radio until battery latch is locked.

5.2.2 Removing the Battery

- Slide the battery latch located on the bottom
of radio to the open position as shown in
figure 5-2.

- The battery is removed by pressing it against
and sliding it towards the bottom of the radio.

Installation of the
Battery

Removing the Battery

- To attach belt clip to radio, align belt clip
rails with the grooves in radio and slide the
belt clip onto the mounting rails until it
latches into place.

- To remove belt clip from radio, push up on
tab of belt clip with flat bladed screwdriver
and at the same time, slide the belt clip
towards the top of Radio(figure 5-3).

▶5.3 Installation and Removal of the Belt Clip

▶6.1 Safety Notes

1) The radio of XU/XV-100 series receives power from high-performance Li-ion battery
(XSB-1800). XSB-1800 Battery is safe of high performance and highly reliable, and
could be charged very fast. XSB-1800 Battery has been designed suitably only for the
charger of Tekk International Inc (DC-100).

The charging of the enclosed Radio on the other maker’s charger will cause
damage to the battery and the Radio.

www.Tekk-Radios.com

to charge the battery.

reception

Radio and place the Radio on the charger (The charger has a slide slot.).

please continue the charging for 30 more minutes for the complete full charge.

The continuous rapid discharge (for example, when making a short circuit on
the ‘+, -’ terminals of battery by a metal substance) may make a fatal defect
and the battery can be exploded. Also, it can cause a fire.

status

During charging

Red LED lights

When charging

Green LED lights

After charging

Green LED lights

Detecting error

Red LED blinks

figure 7-1) User ID

▶7.1 Power On/Off

Turn Power switch clockwise. As soon as power is supplied, the backlight will be turned on.
If the user had set up the user ID, it will be displayed on the LCD and radio will enter into
the latest state as a signal sound is generated.

▶7.2 Transmission Method

For transmission, press PTT button on the left side of the radio. As soon as the user
presses keys according to the setting, DTMF or 5-tone ID will be transmitted, and during
this time, voice communication will be interrupted for several seconds. Then, red LEDs
for transmission and reception will be turned on. It is recommended to talk 5 ~ 10cm
away from the microphone for the best voice communication.

☞Note: If the user makes transmission for more than a certain time while BCLO or TOT

feature is on, transmission will be forcefully disconnected for other users.

When turning (power) on the radio by pressing a button on it, the radio may
enter into a special modes in which transmission and reception is impossible.
Please don’t turn on the radio by above way.

If present channel is TX Inhibited by pc program, TX will not be worked.
(By PC Program, it could be set.)

figure 7-2) When receiving

figure 7-3) When transmitting

▶7.3 Reception Method

The user should not press PTT button during the reception. The user can adjust the
volume by Volume switch, and during reception, the green LED will be turned on.
Depending on conditions of the transmitting radio.

▶7.4 Changing Channels

Channel buttons (▼,▲) are to change channels. Press Up button (▲). Then, “beep”
sound will be generated and the channel number will be increased. Or press Down
button (▼) to decrease the channel. If the user presses Up or Down button while only

www.Tekk-Radios.com

Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 8

▶7.7 2TONE / 5TONE function

7.7.1 2TONE

You can use the private and group tone functions by the central control system which is
using the 2TONE SIGNALING. If the Radio receives the tone signal, the Radio will make
a Beep sound which is advising the tone signal status and which means the Radio is

ready to talk.

7.7.2 5TONE

At the tone mode, you can make the private & group calls by the 5TONE and each call
memory has the call IDs up to 30 numbers. The set-up of call memory and 5-TONE is
made by PC programming. If pressing the Enter button( ) for 2 seconds at the general
mode, the Radio is converted to the call mode and if pressing the Menu button(P) for
2 seconds at the call mode, the Radio is converted to the general mode. By using the
channel buttons (▼,▲) at the call mode, the call number of a channel which is available for
the call is displayed.

figure 7-6) General Mode

figure 7-7) Call Mode

1) 1:1 Call at call mode

Press the Enter button( ) for a long period(about 2 seconds) at the general mode in
order to enter into the call mode.
①Select your party to call by using the channel buttons (▼,▲). If you ( ID : 12345 )

want to call your party(ID : 54321), select him(ID : 54321) by using the channel
buttons (▼,▲) at the call mode.

②You can call the party (ID : 54321) by pressing the Enter button( ) and then, the

Radio of your party(ID:54321) displays the ID number "12345". Even though your
party’s Radio is in general mode, the Radio will be converted to the call mode
automatically.

③After the call is completed, the Transmission and the Reception have no restriction,

which means that the RX/TX will be free.

figure 7-8) ID Selection

figure 7-9) ID Transmission

www.Tekk-Radios.com

①In order to make the Group call at the call mode, the following should be set up at the

PC programming.

②If the 1

st

party (ID:53579) and the 2ndparty(ID:52468) are in one group, the "5AAAA"
which is a call number / call name(example : baseball player) should be designated.
("A" means that all the numbers are applied.)

③If the caller makes a call to the group of baseball players, the caller’s Radio should

press the Menu Button(P) and Up button (▲) at the same time after selecting the
party with ID "1AAAA". In this case, the Radios of the party1 and the party 2 display
the ID "1AAAA". In case of the group call, the party’s Radio displays the group ID
number.

After the call is completed, the Transmission and the Reception have no restriction,
which means that the RX/TX will be free.

This Reset function converts the RX/TX with no restriction to the previous Close mode.
the Monitor button (M) at the call mode.

①The call signal will be transmitted to the party’s Radio with the ID number “C” tone.
②If the party’s Radio is in the Close channel and after receiving the call with the “C”

tone, the call is converted to the “RX/TX with no restriction” mode.

figure 7-10) Group Call

①Press the “P” button of the Radio to turn on. Then, the -Prog- message is displayed.
②Connect the Programming cable to the Ear/Microphone Jack of Radio.
③By using the PC Program, store the data and after disconnecting the cable, turn

off the power and turn on the power again.

figure 7-12) Program Screen

▶7.10 Cloning function

The CLONING is to copy the data such as Frequency/Tone/Scan into the other Radio.

* Cloning Method

①First, please prepare the Cloning cable for XU/XV-100 Series Radio.
②The original Radio should be turned on with pressing the PTT button and the Radio

to be copied should be turned on with pressing the Menu button(P) .

③The original Radio displays -CLON- message, and the Radio to be copied displays

Prog- message.

④Connect the Clon cable to the Ear/Mic Jack of 2 Radios.
⑤If pressing the Enter button( ) of the original Radio, the copy is made and after

completing, please disconnect the cable and turn off & on the power of the 2 Radios.
Finally please use the Radio after checking if the copy is made without problem.

If the Cloning is made into the other maker’s Radio, a malfunction can happen.

original

copy

figure 7-13) CLON Screen

figure 7-11) STUN Screen

▶7.11 Menu description

If pressing the Menu button(P) on the side for 2 seconds, the Radio will be in Menu mode.
The Menu mode consists of 9 Menus and you can use your desired Menu after selection.

After entering into the Menu, if you don’t operate the Menu for more than
8 seconds, the Menu mode will be terminated automatically and it is converted
to the Receiving mode.

www.Tekk-Radios.com

displayed on your Radio to use your Radio in convenience and efficiently.

( ).

Enter button( ) to store.

On( )/Off( ), the Compander ICON( ) on LCD appears/disappears.

①Choose the "Id ANI" by the channel buttons (▼,▲) and press the Enter button( ).

② After the “d-TON” message comes out, choose the ON( )/OFF( ) by the channel

buttons (▼,▲) and press the Enter button( ).

③After the “C-TON” message comes out, choose the ON( )/OFF( ) by the channel

buttons (▼,▲) and press the Enter button( ).

④Comes out of the Menu mode by pressing the Menu button(P).

7.11.4 Scramble selection

The Scramble is for protection from overhearing and the scramble reverses the voice signal

from microphone to a specific frequency and a mixed voice in order for the other person not
to hear your voice.
The selection can be available by PC program and Menu.

①Enter into Menu mode.
②Select “SCrA” by pressing Channel buttons (▼,▲), and press Enter button( ).

③Select On( ) or Off( ) by pressing Channel buttons (▼,▲), and save the selected

status by pressing Enter button( ).

④ Exit Menu mode by pressing Menu Button(P) button. Select Off( ). Then, the “ SCR”

symbol will disappear on the LCD.

( ).

to store.

www.Tekk-Radios.com

③Select On( ) or Off( ) by pressing Channel buttons (▼,▲), and press Enter button

( ).

④ Select on( ). Then, the “vox , H-Fr 05” symbol s will appear on the LCD.

Set sensitivity by pressing Channel buttons (▼,▲), and press Enter button( ).

⑤ Select Off( ). Then, the “vox” symbol will disappear on the LCD.
⑥ Exit Menu mode by pressing Menu Button(P) button.

7.11.8 Set Lone Worker

The Set Lone Worker is for transmission of emergency alarm sound without pressing the
designated button within a period of time when night patrol or guarding and the Lone
Worker can be set to be ON( )/OFF( ).
The selection can be available by PC program and Menu.

①Enter into Menu mode.
②Select “LONE W” by pressing Channel buttons (▼,▲), and press Enter button( ).

③Select On( ) or Off( ) by pressing Channel buttons (▼,▲), and save the selected

status by pressing Enter button( ).

④Exit Menu mode by pressing Menu Button(P) button.

7. Operating Instructions of XU/XV-100 Series Radio

By PC Program and menu, it could be set.

①Enter into Menu mode.
②Select “H-FrEE” by pressing Channel buttons (▼,▲), and press Enter button( ).

www.Tekk-Radios.com