Tekkeon ET1000 User Manual

y

EZTALKER by Tekkeon is a sleek cord-free headset that enables

comfortable handsfree communication with your mobile phone.
1000 works with your Bluetooth-ready mobile phone to provide clear,
high-quality communication.

While using your EZTALKER headset, you can store your mobile phone in
your pocket, backpack, or briefcasejust about anywhere in close
proximity that is convenient for you.

ET1000

EZTALKER

Unpacking EZTALKER

Your ezTalker package includes
the following:

! ezTalker Headset

" Charging cradle with belt clip

# Charger

% ezEarhook

& ezFit Ring

' Comfort Pad

( User guide

(not shown)

#

!

&

"

%

'

USER GUIDE

Charging EZTALKER

Before using ezTalker, you must charge the headset for approximately
two hours. When fully charged, the battery provides up to four hours of
talk time and up to 168 hours of standby time.

To Charge the Headset

1. Insert ezTalker into the charging cradle as
shown.

2. Plug the charger into the charging jack on
the right side of the charging cradle.

3. Plug the charger into a wall outlet.

headset is charging, the amber LED on the
headset will remain on. When the headset is
fully charged, the amber LED will turn off.

4. Unplug the charger cable from the wall outlet and the charging
cradle.

BATTERY INDICATION

capacity), the amber LED will flash and you’ll hear a double beep every
32 seconds.

: When the battery is low (less than 10% of

While the

Figure 1.

ezTalker inserted into

charging cradle

Getting to Know EZTALKER

TALK Button
Used for turning headset on/off,
pairing, and making/receiving calls

Amber and Blue LEDs
Provides visual indication of headset
status: power on/off, pairing mode,
muting mode, charging mode, and low
batter

Volume Control
Used to adjust the speaker volume
and to mute the microphone

Microphone

Speaker

Getting Started

Before using ezTalker, you must:

) Charge ezTalker
) Pair ezTalker to your mobile phone
) Fit ezTalker to your ear
) Power ezTalker

Pairing EZTALKER to Your Mobile Phone

Pairing is the process of linking the headset with your Bluetooth mobile
phone. Before using ezTalker with your mobile phone you must pair the
devices. After this process is complete, you can use the headset only
with its paired mobile phone. To use ezTalker with a different mobile
phone, you must repeat the pairing process with the new mobile phone.
In this case, the headset will no longer work with the original mobile
phone.

BEFORE YOU PAIR THE HEADSET, ENSURE THAT THE BATTERY IS FULLY CHARGED, AND

REVIEW THE INSTRUCTIONS IN YOUR MOBILE PHONE USER GUIDE FOR PAIRING YOUR

MOBILE PHONE TO A BLUETOOTH HEADSET

To Pair the Devices

1. Turn on the mobile phone and place it within 10 feet of the headset.

2. Initiate the Bluetooth device-pairing (discovery) feature on the
mobile phone. Refer to the mobile phone user guide for
instructions on initiating this feature.

3. With the headset turned off, press and hold the TALK button
approximately five seconds, until the blue and amber LEDs flash
alternately or until you hear the PAIRING tone.

4. Release the TALK button.

5. Follow the mobile phone prompts, and when prompted for the
passkey (also called passcode or BT PIN), enter 0000 (the ezTalker
passkey).

Standby Mode, ready to make and receive calls, the amber LED
will turn off, and the blue LED will flash at two-second intervals.

When pairing is complete, the headset will be placed in

.

The headset is now in Pairing Mode

.

Directions for each of these activities are provided in the following four
sections. Once these steps are completed, you will be ready to use
ezTalker!

1

USER GUIDE

To Cancel Pairing Mode

While you are in pairing mode, you can cancel the pairing process and
turn off the headset.

1. While in pairing mode, press and hold the TALK button approximately
three seconds until both LEDs turn off or you hear the OFF tone.

Fitting EZTALKER On Your Ear

EzTalker is designed to fit comfortably in your ear. For added comfort, you
can add the optional ezEarhook , ezFit Ring, and/or comfort foam pad. For
additional comfort, you can add the comfort foam pad that is included
with ezTalker.

To Place the Headset On Your Ear

1. Place the ezTalker speaker in your ear with the microphone angled
toward your mouth as shown. The headset should fit snugly in your
ear and remain in your ear when you move your head. However, if
the speaker is too small for your ear, you can add the ezFit Ring that
is provided with your headset.

To Add the ezFit Ring

1. Stretch the ezFit Ring around the end of
the microphone as shown.

To Add the Comfort Pad

1. Stretch the comfort pad around the end of the
microphone as shown. The comfort pad can be placed
over the ezFit Ring, if both are needed.

To Add the ezEarhook

1. Right ear: From the rear of ezTalker, insert
the bottom of the ezEarhook into the small
hole on the left side of the headset,
pushing until it stops.

Left ear: From the rear of ezTalker,
insert the bottom of the ezEarhook into
the small hole on the right side of the
headset, pushing until it stops.

2. You can mold the soft plastic on ezEarhook

to better fit your ear, and/or adjust the
placement of the ezEarhook stem through
the headset (further in/out).

To Remove the ezEarhook

1. Gently pull the ezEarhook away from the headset until it separates
from the headset.

Figure 2.

ezTalker with ezFit Ring

Figure 3.

ezTalker with Comfort Pad

Figure 4.
ezEarhook connected
for right and left ears

Powering ezTalker

To Turn On the Headset
Press and hold the TALK button approximately four seconds until the

blue LED flashes or until you hear the ON tone.

The headset turns on
and is placed in standby mode, ready to make and receive calls. While
the headset is on and in standby mode, the blue LED will flash at two­second intervals.

To Turn Off the Headset
When the headset is on, press and hold the TALK button approximately

four seconds until the blue LED turns off or until you hear the OFF tone.

The headset turns off.

Making Calls

You can make calls from your mobile phone, or directly from ezTalker
using voice dialing commands (if this feature is supported by your
mobile phone).

To Make Calls From Your Mobile Phone

1. Dial the call from your mobile phone.

connected to your headset.

To Make Calls Using Voice Dialing (if supported by your mobile phone)

1. Press the TALK button on your headset.

2. When prompted by the mobile phone (usually about five seconds),

speak the name of the person you wish to call.

automatically connected to your headset.

TIP

: In a noisy environment, you should dial the number from the mobile

The call is automatically

The call is

phone keypad as the loud background noise may interfere with
voice commands.

Receiving Calls

When you receive a call on your mobile phone, you will hear the mobile
phone ring before you hear the ring tone through your headset as there
is a small delay before the headset recognizes the incoming call.

1. When you hear ring tone on your headset, press the headset TALK

button.

The call is automatically connected to your headset.

NOTE:

For some mobile phones, you must configure the phone to
answer calls directly on your Bluetooth headset. Refer to the mobile
phone user guide for instructions for initiating this feature.

Ending Calls

1. When you have finished your call, press the headset TALK button.

The call will be disconnected.

2