Tekk XM 700 User Manual

Brief Introduction

Thank you for buying handheld two-way radio XM-700. The XM-700 provides cost-effective

communications totally unlicensed for a variety of business and personal communication solutions.

The XM-700 operates on 5 special FCC designated frequencies free for you to use all across the

USA.

Please read this manual carefully in order to know how to properly operate the radio before

use.

Content

Unpacking and Checking Equipment--------------------------------------------------------------1
Parts List ----------------------------------------------------------------------------------------------- 2
Preparation----------------------------------------------------------------------------------------------2
Basic operations----------------------------------------------------------------------------------------3
LCD Icons Instructions-------------------------------------------------------------------------------4

Channel Information ---------------------------------------------------------------------------------5

Optional Items------------------------------------------------------------------------------------------5

VOX ---------------------------------------------------------------------------------------------------7

Battery ----------------------------------------------------------------------------------------------------7

Emergency Call -------------------------------------------------------------------------------------8

First /Quick Channel -------------------------------------------------------------------------------9

Information Input--------------------------------------------------------------------------------------9

Power On Setting --------------------------------------------------------------------------------------9

Troubleshooting ----------------------------------------------------------------------------------------11
Specification --------------------------------------------------------------------------------------------11
Appendix II CTCSS (Hz) ----------------------------------------------------------------------------11
Appendix III DCS-------------------------------------------------------------------------------------12

Unpacking and Checking Equipment

Welcome to use TEKK radios, before using we suggest you:

·Please check the packing box of this product and see if there are signs of damage.

·Please open the packing box carefully. We recommend that you identify the items listed in the

following packing list. if you find that our product and its accessories in handling are lost or

damaged during the shipment. Please immediately contact TEKK dealers.

Parts List

Item Quantity

Rubber Antenna 1

Li-ion Battery Pack 1

Desktop Charger 1

Power Adapter 1

Belt Clip 1

User’s Manual 1

Preparation

Charging the Battery

1) Using the battery

The

battery is not completely charged at the factory, please charge it before using.

To extend the battery life time, please power off the battery when you don't use two way
radio, and save battery in a cool (temperature less than 25 )and dry place.℃

2 Precautions of Charging Equipment

1. Do not expose the charger to rain or snow.

2. Do not operate the charger if it has received a sharp blow, or has been dropped or damaged

in any way.

3. Do not disassemble the charger if it has received a sharp blow, or has been dropped or

damaged in any way.

4. Never alter the AC cord or plug provided with the unit. If the plug will not fit the outlet,

have the proper outlet installed by a qualified electrician. An improper condition can result

in a risk of electric shock.

5. To reduce the risk of damage to the cord or plug, pull the plug rather than the cord when

disconnecting the charger from the AC receptacle.

6. To reduce the risk of electric shock, unplug the charger from the outlet before attempting

any maintenance or cleaning.

7. Use of an attachment not recommended or sold by TEKK may result in a risk of fire,

electric shock, or personal injury.

8. Make sure the cord is located so it will not be stepped on, tripped over, or subjected to

damage or stress.

9. An extension cord should not be used unless absolutely necessary. Use of an improper

extension cord could result in a risk of fire and/or electric shock. If an extension cord must

be used, make sure that:

•The pins on the plug of the extension cord are the same number, size, and shape as those

on the plug of the charger.

•The extension cord is properly wired and in good electrical condition.

•The cord size is 18 AWG for lengths up to 100 feet, and 16 AWG for lengths up to

150feet.

10. Do not replace charger's power cord. If the power cord damages, you must stop using

charger immediately.

3. Charging the Battery

Please use the battery charger designated by TEKK to charge battery. After purchase or

extended storage (more than two months), the first time to charge battery cannot make

battery reach its normal operating capacity. After repeating charge /discharge it two or

three times, the operating capacity will increase to its normal capacity.

4. Please Charge the Radio According to Operation Steps as Follows:

1. Insert power adapter into power supply socket.

2. Insert output terminal of power adapter into DC jack behind the charging kit, now the

charging orange indicator lights about 2 seconds then goes out.

3. Insert the battery or radio equipped with battery into the charging kit.

4. Confirm the battery and charging kit terminal contact reliably, when charging indicator

light turns into red and charging starts.

5. After completion of charge (charging time about 5 hours), light turns to be green.

5. Indicators Display As Following:

Status Indicator

Power Connected Orange light is on about 2 seconds then goes out

No battery(temperature end judges) All go out

Charge normally Red light is on

The battery is fully charged Green light is on

Fault (over temperature, battery short

circuit or over discharge state)

Note: Before charging, please turn off radio power equipped with battery. When
charging, using radio will interfere with normal charge of battery and transceiver
effect.

Red light flashes

Basic operations

1) Power On/Off

Turn the power switch knob clockwise to turn on radio power; to turn it off ,turn

the power switch knob counter-clockwise.

Volume Control

2)

Turn the volume switch knob clockwise to increase volume; to decrease the

volume, rotate the volume switch knob counter-clockwise.

TX

3)

1. According to different settings of monitor ,please monitor the radio for some while .Ensure

there is no radio transmitting at the chosen channel .

2. Press PTT and face to microphone talking .

1) Please make the distance between your lip and microphone at 2.5-5 cm ,and talk as usual

to get the best voice quality .

2) Press and hold PTT, LED red light is on .

3) Release PTT to receive information .

3. When using earphone with VOX function ,users can hands-free talking .

4. Also users can active the IVOX function which no need to use earphone .

4) RX

When radio receiving information ,green LED lights .

1) Only same signaling and CTCSS setting can receive information .

2) May not receive any calling if radio is at lower signal and set high level SQL.

3) Local dealer maybe program your radio with CTCSS/DCS . Users can receive the same

signaling information if chosen channel with CTCSS/DCS . Or it can not get any calling .

Radio with CTCSS/DCS will help you to ignore ineffective calling. Although there seems

special channel for CTCSS/DCS ,radio also can communicate with other radio which

programmed the same CTCSS /DCS .

LCD Icons Instruction

ICON ILLUSTRATION

1
2
3
4
5

Key lock

CTCSS

DCS

Battery Gauge Indicator

Narrow band

6
7
8
9
10
11

Lower power

VOX

First Scan

Scan

Channel No. Menu NO.

Signal Level for TX and RX

Program Settings

Channel Information

 Radio Basic Information

1) Channels

Please choose desired channel number as working channel.

2) Turn On SP

Turn on speaker, you can hear sound from radio when it receives correct signaling .

Function 1

 Optional Items

 TOT

This function can prevent users occupied the present channel for long time and limit TX time,
meanwhile prevent radio from damage by long time transmitting .

 Alarm before TOT

You can set an alert tone sounds from the speaker before TOT is cut.

 Voice Report

Your radio can choose different languages voice report : English ,Chinese ,Off .

 Beeper of Power On

Choose desired beeper to sound when turn on the radio .

 SQL

The purpose of the squelch is to mute the speaker when no signals are present. With the squelch

level ( 0-9) correctly set , you will hear sound only while actually receiving signal. The higher

the selected squelch level, the stronger the signals must be when receive. The appropriate

squelch level depends on ambient RF noise conditions.

 Key Lock