Tekcomm TCT2100 User Manual
Manuel d’utilisation
User Manual
Terminal Numérique Terrestre
Haute Défi nition TCT2100
1000
channels
USB
enregistrement
TV
INFO
Digital
audio
Sous-titres
Télétexte
8
listes
favoris
Recherche
autom/man.
Contrôle
parental
AC 220-240 V~ 50/60 Hz. max. 12 W
ANT IN
Digital Terrestrial High Definition Receiver
Model: TCT2100
USB: 5 V
800 mA max.
DC 5 V
50 mA max
MANUFACTURED UNDER LICENSE
FROM DOLBY LABORATORIES.
DOLBY AND THE DOUBLE-D SYMBOL
ARE TRADEMARKS OF
DOLBY LABORATORIES.
AC 220-240 V~ 50/60 Hz. max. 12 W
ANT IN
Digital Terrestrial High Definition Receiver
Model: TCT2100
USB: 5 V
800 mA max.
DC 5 V
50 mA max
MANUFACTURED UNDER LICENSE
FROM DOLBY LABORATORIES.
DOLBY AND THE DOUBLE-D SYMBOL
ARE TRADEMARKS OF
DOLBY LABORATORIES.
AC 220-240 V~ 50/60 Hz. max. 12 W
ANT IN
Digital Terrestrial High Definition Receiver
Model: TCT2100
USB: 5 V
800 mA max.
DC 5 V
50 mA max
MANUFACTURED UNDER LICENSE
FROM DOLBY LABORATORIES.
DOLBY AND THE DOUBLE-D SYMBOL
ARE TRADEMARKS OF
DOLBY LABORATORIES.
Supplied by STRONG & Co, Japan
Represented by STRONG Ges.m.b.H.
Franz-Josefs-Kai 1
1010 Vienna
Austria
Email: support_at@strong.tv
17 Jun 2015 12:23
Licenses
ANY USE OF THIS PRODUCT IN ANY MANNER OTHER THAN PERSONAL USE THAT COMPLIES
WITH THE MPEG-2 STANDARD FOR ENCODING VIDEO INFORMATION FOR PACKAGED MEDIA
IS EXPRESSLY PROHIBITED WITHOUT A LICENSE UNDER APPLICABLE PATENTS IN THE MPEG-2
PATENT PORTFOLIO, WHICH LICENSE IS AVAILABLE FROM MPEG LA, LLC, 6312 S. Fiddlers
Green Circle, Suite 400E, Greenwood Village, Colorado 80111 U.S.A.
THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND
NONCOMMERCIAL USE OF A CONSUMER TO (i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC
STANDARD (“AVC VIDEO”) AND/OR (ii) DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER
ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A
VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED
FOR ANY OTHER USE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE
HTTP://WWW.MPEGLA.COM
This product contains one or more programs protected under international and U.S. copyright
laws as unpublished works. They are confidential and proprietary to Dolby Laboratories. Their
reproduction or disclosure, in whole or in part, or the production of derivative works therefrom
without the express permission of Dolby Laboratories is prohibited. Copyright 2003-2009 by Dolby
Laboratories. All rights reserved.
English
1
TABLE OF CONTENT
1.0 INTRODUCTION 3
1.1 Safety Instructions 3
1.2 Storage 3
1.3 Equipment Set-up 4
1.4 Accessories 4
1.5 Usage of external USB devices 4
2.0 YOUR RECEIVER 5
2.1 DEFAULT PIN: 1234 5
2.2 Front Panel 5
2.3 Rear Panel 5
2.4 Remote control 5
2.5 Installing the batteries 6
2.6 Using the remote control 6
3.0 CONNECTIONS 6
3.1 Connecting to a terrestrial
antenna 6
3.2 Connecting to TV with HDMI
cable 7
3.3 Connecting to TV with SCART
cable 7
3.4 Connecting to a digital audio
amplifier and TV using HDMI 7
3.5 Connecting to an analogue
Audio Amplifier 7
3.6 Connecting a USB storage
device 7
4.0 STARTING UP FOR THE FIRST TIME 8
5.0 QUICK GUIDE TO USING
YOUR RECEIVER 9
6.0 OPERATION 9
6.1 Changing channels 9
6.2 Info Banner 9
6.3 Selection of audio language 10
6.4 Teletext 10
6.5 Subtitles 10
6.6 Timeshift 10
6.7 EPG (Electronic Programme
Guide) 10
6.8 Instant Recording 11
7.0 MAIN MENU 11
7.1 Edit Channel 11
7.2 Installation 13
7.3 System Setup 14
7.4 Tools 17
7.5 Games 18
7.6 Media 19
17 Jun 2015 12:34
TEKCOMM declares that this item complies with the basic requirements and other relevant regulations of directives
2004/108/EC and 73/23/EC, RoHS 2002/95/EC
Subject to alterations. In consequence of continuous research and development technical specifications, design and
appearance of products may change. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC in the United States and other countries. Manufactured under license from
Dolby Laboratories. Dolby and the double-D symbol are registered trademarks of Dolby Laboratories. All other product
names are trademarks or registered trademarks of their respective owners.
© TEKCOMM 2015. All rights reserved.
2
1.0 INTRODUCTION
1.1 Safety Instructions
DO NOT INSTALL YOUR RECEIVER:
In a closed or poorly ventilated cabinet; directly on top of or under any other equipment; on a
surface which might obstruct the ventilation slots.
DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES:
To direct sunlight or any other equipment that generates heat; to rain or intense moisture; to
intense vibration and to any shock which may cause permanent damage to your receiver or to
any magnetic objects, such as loudspeakers, transformers, etc.
Do not use a damaged power cord. It may cause a fire or an electric shock. Do not touch a
power cord with wet hands. It may cause an electric shock.
When the receiver is not used for a long period of time, you should unplug the power cord
from the wall socket.
Do not use alcohol or ammonia based liquids to clean the receiver. If you wish, you may clean
your receiver with a soft lint-free cloth slightly made damp with a mild soap solution, and only
after disconnecting from the mains voltage supply. Make sure no foreign objects fall through
the ventilation slots because this could cause fire or an electric shock.
Do not place any objects on top of the receiver because this might prevent proper cooling of
the components inside.
Safety Precautions
Never try to open the receiver. It is dangerous to touch the inside of the receiver due to high
voltages and possible electrical hazards. Opening the receiver will void the warranty of the
product. Refer all maintenance or servicing to suitably qualified personnel.
When you are connecting cables, be sure that the receiver is disconnected from the mains
supply voltage. Wait a few seconds after switching off the receiver before you move the
receiver or disconnect any equipment.
It is a necessity that you only use an approved extension and compatible wiring that is suitable
for the electrical power consumption of the installed equipment. Please ensure that the
electrical power supply corresponds with the voltage on the electrical identification plate at the
back of the receiver.
If the receiver does not operate normally even after strictly following the instructions in this user
manual, it is recommended to consult your dealer.
1.2 Storage
Your receiver and its accessories are stored and delivered in a packaging designed to protect against
electric shocks and moisture. When unpacking it, make sure that all the parts are included and keep
the packaging away from children. When transporting the receiver from one place to another or
if you are returning it under warranty conditions, make sure to repack the receiver in its original
packaging with its accessories. Failing to comply with such packaging procedures could damage the
product and void your warranty.
English
3
1.3 Equipment Set-up
We recommend you consult a professional installer to set up your equipment. Otherwise, please
follow the instructions below:
Refer to the user manual of your TV and, if applicable, your antenna.
Make sure that the HDMI cable and, if applicable, outdoor components are in a good condition.
If you use TV SCART connection, use then well shielded SCART cable.
This user manual provides complete instructions for installing and using this receiver. The symbols
serve as follows.
Warning Indicates warning information.
Tips Indicates any other additional important or helpful information.
MENU Represents a button on the remote control or the receiver.
(Bold characters)
Move to Represents a menu item within a window.
(Italic characters)
1.4 Accessories
Installation Instructions
1 remote control unit
2x batteries (AAA type)
WARNING: The batteries should not be recharged, disassembled, electrically short-
circuited, be mixed or used with other types of batteries. If rechargeable
accumulators instead of batteries are going to be used (e.g. NiMH), we
recommend using types with low self-discharge to ensure long time
operation of your remote control.
1.5 Usage of external USB devices
It is recommended to use USB 2.0 storage devices or higher. If your device is not compatible
to USB 2.0 specifications, recording, playback and other multimedia functions of the receiver
might not work properly.
To ensure best performance of your USB storage device please format it via your receiver
(through the menu “Media”) to FAT32 system. Other file systems are not supported by the
receiver. However, it is possible to use already NTFS formatted disks.
TEKCOMM cannot guarantee compatibility with all types of USB storage devices.
If you are going to use external USB HDDs (Hard Disk Drives), please consider that power
specifications may exceed the supported output of your receiver (max.5 V/800 mA). If so, please
connect your USB HDD to an according external power adapter.
It is advised not to store important information on USB storage devices used with the receiver.
Always make backups of data on your USB storage device before using it with this receiver.
TEKCOMM will not take responsibility for any loss of information or circumstances caused by
loss of information.
4
2.0 YOUR RECEIVER
2.1 DEFAULT PIN: 1234
2.2 Front Panel
Fig. 1
1. USB Connector for USB storage devices.
2. IR sensor Point your remote control towards this sensor.
3. Mode indicator RED indicates that the receiver is in STANDBY mode.
GREEN indicates that the receiver is in OPERATING mode.
4. Standby/On button Switch receiver ON to running mode or STANDBY mode
2.3 Rear Panel
Fig. 2
1. ANT IN To connect to your antenna for reception of broadcasted signals.
2. HDMI To connect your receiver with your TV set using an HDMI cable.
3. TV SCART To connect your receiver with your TV set using a SCART cable.
4. Power cord Your receiver requires a supply voltage of 220 – 240 V AC
(Auto-selectable), 50/60Hz +/-5%. Please ensure the local power
specification meets these requirements before connecting your
receiver to the wall outlet.
2.4 Remote control
Fig. 3
1. q Switches the receiver On/Standby
2. ! Mutes all audio outputs of the receiver
3. PG+/PG- Page up/down in all list modes
4. DTV/VCR No function
5. INFO Opens the current channel information; 2x opens the current
event information and 3x the signal information
6. VOL+/VOL- Increases/decreases the volume level
7. MENU Opens the main menu, in a menu you will get one step back
8. EXIT Exits from the menu or sub-menu
9. pq Menu Off: Change channel to next/previous.
Menu On: Moves the cursor up/down.
10. tu Menu Off: Decreases/ increases the volume level.
Menu On: Change settings for specific menus
11. OK Menu Off: Displays the current channel list
Menu On: Activates the highlighted menu item.
12. RECORD Records the TV programme to the connected USB storage device
13. TIMESHIFT Activates the Timeshift function (Off/On)
14. 0~9 Enters a channel number in viewing mode or a value inside the
respective menu
15. EPG Opens the EPG (Electronic Programme Guide) in TV mode
English
5
Loading...