Teka EX-70 5G AI AL TR FUND, EX-70 5G AI TR FUND, EX-60 4G AI FUND User Manual

Instructions for the installation

and advice for the maintenance

EX/60 4G AI FUND

EX/70 5G AI TR FUND - EX/70 5G AI AL TR FUND

Instructions Manual

EX/60 4G AI FUND

EX/70 5G AI TR FUND - EX/70 5G AI AL TR FUND

COD. 04038GBTK - 24.05.2005

1 Ultra rapid burner of 3100 W 2 Rapid gas burner of 2800 W 3 Semirapid gas burner of 1750 W 4 Auxiliary gas burner of 1000 W 5 Enamelled steel pan support 2F 6 Enamelled steel pan support 1F 7 Burner n° 1 control knob 8 Burner n° 2 control knob 9 Burner n° 3 control knob 10 Burner n° 4 control knob 11 Electric ignition button

Attention: this appliance has been manufactured for domestic use only and it employment by private person.

DESCRIPTION OF THE HOT PLATES

TYPES: EX/60 4G AI FUND - EX/70 5G AI TR FUND - EX/70 5G AI AL TR FUND

1) BURNERS

A diagram is screen-printed above each knob on the front panel. This diagram indicates to which burner the knob in question corresponds. After having opened the gas mains or gas bottle tap, light the burners as described below:

- Manual ignition

Push and turn the knob corresponding to the required burner in an anticlockwise direction until it reaches the full on position (large flame fig. 1), then place a lighted match near the burner.

- Automatic electrical ignition

Push and turn the knob corresponding to the required burner in an anticlockwise direction until it reaches the full on position (large flame fig. 1), then depress the knob.

- Lighting burners equipped with flame failure device

The knobs of burners equipped with flame failure device must be turned in an anticlockwise direction until they reach the full on position (large flame fig.1) and come to a stop. Now depress the knob in question and repeat the previously indicated operations. Keep the knob depressed for about 10 seconds once the burner has ignited.

HOW TO USE THE BURNERS

Bear in mind the following indications in order to achieve maximum efficiency with the least possible gas consumption:

- Use adequate pans for each burner (consult the following table and fig. 2).

- When the pan comes to the boil, set the knob to the reduced rate position (small flame fig. 1).

- Always place a lid on the pans.

- Use only pan with a flat bottom.

Burners Power ratings Pan Ø in cm

Ultra rapid 3100 24 ÷ 26 Rapid 2800 20 ÷ 22 Semirapid 1750 16 ÷ 18 Auxiliary 1000 10 ÷ 14

WARNINGS:

- Burners with flame failure device may only be ignited when the relative knob has been set to the Full on position (large flame fig. 1).

- Matches can be used to ignite the burners in a blackout.

- Never leave the appliance unattended when the burners are being used. Make sure there are no children in the near vicinity. Particularly make sure that the pan handles are correctly positioned and keep a chek on foods requiring oil and grease to cook since these products can easily catch fire.

- Never use aerosols near the appliance when it is operating.

- If the built-in hot plate has a lid, any spilt food should be immediately removed from this before it is opened. If the appliance has a glass lid, this could shatter when the hot plate becomes hot. Always switch off all the burners before closing the lid.

USE

FIG. 1 FIG. 2

USE

Notes: Use of a gas cooking appliance produces heat and moisture in the room in which it is installed. The room must therefore be well ventilated by keeping the natural air vents clear (fig. 3) and by activating the mechanical aeration device (suction hood or electric fan fig. 4 and fig. 5). Intensive and lengthy use of the appliance may require additional ventilation. This can be achieved by opening a window or by increasing the power of the mechanical exhausting system if installed.

FIG. 3 FIG. 4 FIG. 5

(*) AIR INLET: SEE INSTALLATION CHAPTER (PARAGRAPHS 5 AND 6)

CLEANING

IMPORTANT: Always disconnect the appliance from the gas and electricity mains before carrying out any cleaning operation.

2) HOT PLATE

Periodically wash the hot plate, the enamelled stell pan support, the enamelled burner caps "C" and the burner heads "T" (see fig. 6) with lukewarm soapy water. Following this, all parts should be thoroughly rinsed and dried. Never wash them while they are still warm and never use abrasive powders. Do not allow vinegar, coffee, milk, salted water, lemon or tomato juice from remaining in contact with the enamelled surfaces for long periods of time.

WARNINGS: Comply with the following instructions, before remounting the parts:

- Check that burner head "T" (fig. 6) slots have not become clogged by foreign bodies.

- Check that enamelled burner cap "C" (fig. 6) have correctly positioned on the burner head. It must be steady.

- The exact position of the pan support is established by the rounded corners, which should be set towards the side edge of the hot plate.

- Do not force the taps if they are difficult open or close. Contact the technical assistance service for repairs.

- Correctly preserve the plate after use by treating it with special products, easily available on the market. This will keep the surface of the plate clean and bright. The operation will also prevent the formation of rust.

- Don’t use steam jets for the equipment cleaning.

FIG. 6

+ 10 hidden pages