Teguar TMT-4391-08 Series Startup Manual

Medical Computer
TMT-4391-08 Series
Startup Manual

TMT-4391-08 Appearance

Left: Front View Right: Rear View

For more information on this and other Teguar
products, please visit our website at:

http://www.teguar.com

For technical support and service, please visit
our support website at:

http://www.teguar.com/support

This manual is for TMT-4391-08 Series
3rd Edition

Print in China August 2018

Description of Parts

A: Front Camera
B: Power LED
C: Light Sensor
D: Speaker
E: micro-SIM & micro-SD Card Door
F: Programmable Key (Default
Barcode scanner)
G: Pogo Pin (USB3.0)
H: Micro USB Door
I: Micro HDMI Door
J: Power Button
K: Volume Key (Up/Down)
L: Audio Jack (Headset Combo)
M: Extension Module
N: NFC
O: Rear Camera with LED Flash
P: Battery Cover

Easy Setup

Power On Computer

1. Model: TMT-4391-08 Rating 5 Vdc / 3.0A

2. This product is intended to be supplied by a UL
Listed Power Adapter (Phihong / MM18M-59A) or
DC power source, rated 5 Vdc, 3A min. for model
TMT-4391-08, and Tma 45 degree C. Please
contact Teguar for further information and
assistance.

3. The product is equipped with shipping mode for
battery protected and power saving, please charge
the embedded battery of the computer: Connect
the Micro USB adaptor on the TMT-4391-08
computer. (“H” on the description of parts.) Please
charge for at least one hour when you use this
computer for the first time.

4. Push the Power button (“J” on description of parts.)
for 2~3 seconds to start the computer.

5. The product is equipped with a 8” Capacitive
T ouch Panel. Use finger , capacitive stylus, or nitrile
gloves to touch the following Active Area to
operate the computer.

6. The product is equipped with one LED indicator for
battery status. The following shows LED status for
different power states:
a) The orange LED blinks when internal battery

capacity is below 10% to warn the user to
charge.

b) The Blue LED lights up when internal battery is

being charged.

c) The Green LED light s up when internal b attery

has been fully charged.

7. While the computer is running, push the power
button for 1 second will disable LCD backlight for
power saving. Push the power button again will
enable the backlight again; press the power button
for 10 seconds while computer is running, the
system will shut down.

8. Environment:

 Operating Temperature: -10°C ~ +50 °C
 Operating Humidity : 10% ~ 90%@30°C

non-condensed

 Storage/Transportation Temperature:

-40°C ~ +80°C (Internal lab test)

 Storage/Transportation Humidity :

5% ~ 95%@30°C non-condensed

 Humidity consider to 25°C, 48 hrs
 Number and type of Means of Protection :

MOPP Altitude 3000m

 Atmospheric pressure： 700-1013 hPa (for

operating); 500-1013 hPa (for
Storage/Transportation)

 IP level : IPX0

9. There will be “TEGUAR” l ogo upside down while
first boot up. This scenario will be disappear after
2

nd

boot up and won’t influence functions and

usage.

Intended Use

The TMT-4391-08 is intended for integration with
hospital system. It is designed for general purpose for
hospital environment.
For data collection and display for reference.
It should not be used for life-supporting system.

EMC Table

Guidance and Manufacturer’s Declaration –
Electromagnetic Emissions

The model TMT-4391-08 is intended for use in an
electromagnetic environment as specified below. The
customer or the user of the TMT-4391-08 should assure
that it is used in such an environment.

Emissions Test

Compliance

Electromagnetic
Environmental
Guidance

The model
TMT

-4391-08 uses

RF RF emissions

energy only for its
internal func-

Group 1

tion. Therefore, its RF
emissions

CISPR 11

are very low and are
not likely to

cause any
interference in nearby

electronic equipment.

RF emissions

Class B

The model
TMT

-4391-08 is

suitable

CISPR 11

for use in all
establishments,

Harmonic
emissions

Class A

including domestic
establishments

IEC 61000-3-2

and those directly
connected to

the public low-voltage
power sup-

Voltage
fluctuations/

ply network that
supplies buildings

flicker emissions

Not applicable

used for domestic
purposes.

IEC 61000-3-3

Recommended Separation Distances Between
Portable and Mobile RF Communications Equipment
and the TMT-4391-08

TMT-4391-08 is intended for use in an electromagnetic
environment in which radiated RF disturbances are
controlled. The customer or the user of the model
TMT-4391-08 can help prevent electromagnetic
interference by maintaining a minimum distance between
portable and mobile RF communications equipment
(transmitters) and the model TMT-4391-08 as
recommended below, according to the maximum output
power of the communications equipment.

Rated
Maximum

Output
Power of

Separation Distance According to
Frequency of Transmitter

Transmitter

m

W

150 kHz to
80 MHz

80 MHz to
800 MHz

800 MHz to
2,5 GHz

d = 1,2 P

d = 1,2 P

d = 2,3 P

0,01

0,12

0,12

0,23

0,1

0,38

0,38

0,73

1

1,2

1,2

2,3

10

3,8

3,8

7,3

100

12

12

23

For transmitters rated at a maximum output power not
listed above, the recommended separation distance d in
meters (m) can be estimated using the equation in the
table above applicable to the frequency of the transmitter,
where P is the maximum output power rating of the
transmitter in watts (W) according to the transmitter
manufacturer.

NOTE 1 At 80 MHz and 800 MHz, the separation
distance for the higher frequency range applies.

NOTE 2 These guidelines may not apply in all situations.
Electromagnetic propagation is affected by absorption
and reflection from structures, objects and people.

Guidance and Manufacturer’s Declaration –
Electromagnetic Immunity

TMT-4391-08 is intended for use in the electromagnetic
environment specified below. The customer or the user
of the model TMT-4391-08 sho uld assur e that it is used
in such an environment.

Immunity
Test

IEC 60601
Test

Compliance

Electromagnet
ic
Environmental

Level

Level

Guidance

Electrostatic
dis-

Floors should
be wood, con-

±8 kV

contact



±8 kV

contact

crete or ceramic
tile. If floors

charge (ESD)

are covered
with synthetic

±

15 kV

air

±15 kV air

IEC
61000-4-2

material, the
relative
humidity

should be at
least 30%.

Electrical fast

±

2 kV for

power

±

2 kV for

power

supply lines

supply lines

Main power
quality should
be

transient/bur
st

that of a typical
commercial or



±1 kV for

input/out-



±1 kV for

input/

IEC
61000-4-4

hospital
environment.

put lines

output lines

±

1 kV

line(s) to

±

1 kV

line(s) to

Main power
quality should
be Surge

line(s)

line(s)

that of a typical
commercial or

IEC
61000-4-5

±

2 kV

line(s) to

±

2 kV

line(s) to

hospital
environment.

earth

earth

<5%

UT

(>95% dip

<5% UT

(>95% dip in

in UT) for
0,5 cycle

UT) for 0,5

Main power
quality should
be cycle

40% UT

that of a typical
commercial or

Interruptions
and

(60% dip in
UT)

40%

UT

(60%

hospital
environment. If
the voltage varia-

for 5 cycles

dip in UT) for
5

user of the
model
TMT-4391-08

tions on
power

cycles

requires
continued
operation

supply input
lines

70% UT

during main
power interrup-

(30% dip in
UT)

70%

UT

(30%

tion, it is
recommended
that

IEC
61000-4-11

for 25
cycles

dip in UT) for

the model
TMT

-4391-08

be 25 cycles

powered from
an uninterrupt-

<5% UT

<5% UT

ible power
supply or a
battery.

(>95% dip
in UT)

for 5 sec

(>95% dip in

UT) for 5 sec

Power
frequency

Power
frequency
magnetic

fields should be
at levels

(50/60 Hz)

3 A/m

3 A/m

characteristic of
a typical

magnetic
field

location in a
typical commer-

IEC
61000-4-8

cial or hospital
environment.

NOTE UT is the A.C. main voltage prior to application of
the test level.

Guidance and Manufacturer’s Declaration –
Electromagnetic Immunity

The model TMT-4391-08 is intended for use in the
electromagnetic environment specified below. The
customer or the user of the model TMT-4391-08 should
assure that it is used in such an environment.

Immunity

IEC 60601
Test

Compliance

Electromagnet
ic
Environmental

test

Level

Level

Guidance

Portable and
mobile RF
communi-

cations
equipment
should be used

no closer to any
part of the
model

TMT-4391-08,
including
cables, than

the
recommended
separation dis-

tance
calculated from
the equation

applicable to
the frequency
of the

transmitter.

Recommende
d Separation
Dis-

tance

d = 1,2 P

d =

1,2 P

80 MHz to 800
MHz

Conducted

3 Vrms

RF

d = 2,3 P
800 MHz to 2,5
GHz

150 kHz

to

80

IEC
61000-4-6

MHz

Vrms

where P is the
maximum
output

Radiated
RF

3 V/m

V/m

power rating of
the transmitter
in

watts (W)
according to the
transmit-

80 MHz to
2,5

IEC
61000-4-3

ter
manufacturer
and d is the rec-

GHz

ommended
separation
distance in

meters (m).

Field strengths
from fixed RF
trans-

mitters, as
determined by
an elec-

tromagnetic site
survey,

a

should

be

less than the
compliance
level in

each

frequency

range. b

Interference
may occur in t he
vicin-

ity of equipment
marked with the
fol-

lowing symbol:

NOTE 1 At 80 MHz and 800 MHz, the higher frequency
range applies.

NOTE 2 These guidelines may not apply in all situations.
Electromagnetic propagation is affected by absorption
and reflection from structures, objects and people.