Teeter Hang Ups F9000 Assembly Instructions Manual

ASSEMBLY INSTRUCTIONS

TM

F9000

PRE-ASSEMBLY

Before you begin: These instructions will guide you in properly assembling the unit. Please review all the steps before beginning

assembly. Carefully adhere to the Assembly Instructions and Owner’s Manual to help ensure user safety and product integrity.

!

W ARNING

1. It is your responsibility to familiarize yourself with the proper use of the equipment and the inherent risks of inversion, such as
falling on your head or neck, pinching, entrapment or equipment failure.

2. This product is not designed for persons over 198 cm (6’6”) or 136 kg (300 lbs). Structural failure could occur or head/neck may
impact floor during inversion. Serious injury or death could result.

3.

DO NOT use this equipment without a licensed physician’s approval and a review of the medical contraindications, as noted in

the Owner’s Manual.

4. Failure to assemble and/or use the equipment as directed may void the manufacturer’s warranty on this product and could result
in injury or death.

5.

DO NOT use the inversion table until you have thoroughly and carefully read the Owner’s Manual, viewed the Instructional Video,

reviewed all other accompanying documents, and inspected the equipment. The Instructional Video is in English. The steps in
the video directly coincide with the steps detailed in these Assembly Instructions.

6. Choose a level surface for assembling and operating the table.

7. Follow each step in sequence. Do not skip ahead.

8. Make sure that all fasteners are secure.

9.

PRIOR TO USE, test and inspect the table. Make sure the table rotates smoothly to inverted position and back.

10. Replace defective components immediately and/ore keep the equipment out of use until repair.

Carefully remove the individual parts from the carton. You should have all of the items listed below. If any items are missing or
damaged, contact your retailer or customer service directly (See Pg. 4).

U.S. and foreign patents apply. Other foreign p atents pending.

ITEMS FOR ASSEMBL Y ITEM #’s

A-frame base F71002

F71002

F91039

w/ EZ-Angle Tether Strap F51008
Main shaft w/ ankle clamp F91039
Table frame with mat F51021

Hand grips (2) and F51069

13 mm

(1/2”) hex bolts (6) H11202

F51008

Two (2) roller hinges F51064
Two (2) wrenches F51088

F51021

ASSEMBLY

STEP ONE
Assemble the A-frame Base (F71002)

• Open the A-frame and make sure that the spreader arms are locked flat. (See
Figure 1)

NOTE: Bolts may be

Figure 2

packaged separately

or assembled in

hand grips.

Spreader Arms

F51069

F51088

H11202

Bolts may be

packaged

separately or

assembled in

hand grips.

F51064

Figure 1

(R)

(L)

STEP TWO
Install Hand Grips (F51069) on A-frame Base (F71002)

• Place one of each hand grip (left / right) over the outside edge of the corre­sponding hinge plate. (See Figure 2)

• Insert three 13 mm (1/2”) hex bolts (H11202) through the hinge plate into each
hand grip. Use the wrenches provided to tighten the bolts, being careful not to
over tighten.

DO NOT DISCARD - KEEP FOR FUTURE REFERENCE.

front rear

ASSEMBLY

STEP THREE

Install Roller Hinges (F51064) to T able Frame (F51021)

• For ease of assembly , rest the t able frame against the crossbar at the
front of the A-frame.

• Open the cam locks on each side of the table frame.

• With the grooved pivot pins facing out, insert the roller hinges into the
brackets on each side of the table frame. (See Figure 3) The roller hinges
will slide between the cam locks and the brackets. (See Figure 3A)

• Make sure that the roller hinges are in the same hole setting on both
sides.

• Push down on the cam lock to secure the hinge. Figure 3B shows the
roller hinge engaged correctly (in Setting C).

Refer to the Owner’s Manual for an explanation of the hole settings.

We suggest using Setting C to start.

Figure 3

In Setting C

Hinge
into
bracket

pivot
pin

Close
cam lock

Figure 4

STEP FOUR

Attach the T able Frame (F51021) to the A-frame (F71002)

• Holding each side near the roller hinges, pick up the table frame and stand at
the front of the A-frame. Lower each pivot pin into the A-frame hinge plates at
the same time. (See Figure 4) Figure 4A shows the correct placement of the
pivot pin into the hinge plate.

• Make sure that both pivot pins are seated at the base of the slot in the
hinge plate.

• Check to make sure that the self-locking hooks have closed over both
pivot pins and that the table rotates smoothly .

Failure of the self-locking hooks to close over both pivot pins

is indication of improper assembly and if not corrected,

could result in serious injury or death.

Figure 4A

STEP FIVE

Insert the Main Shaft (F91039) into the Table Frame (F51021)

• Loosen the de-rattler knob on the main shaft housing.

• With the height adjustment settings on the main shaft facing up, slide the
end of the main shaft into the blue bushing in the main shaft housing. (See

Figure 5)

• Pull out the height selector locking pin to allow the main shaft to slide in
further. For the purpose of easy assembly, slide the main shaft in all the
way and release the pin in the storage setting. (Refer to the Owner’s
Manual for proper height adjustment before use).

• Tighten the de-rattler knob.

Figure 3A

!

W ARNING

Figure 5

Figure 3B

de-rattler
knob

!

W ARNING

Read the Owner’s Manual for information on

selecting the correct user height setting.

Improper settings could result in serious injury or death.

Assembly Instructions #IIL202 Pg. 2