TECSYSTEM TTG SERIES Instruction Manual

INSTRUCTION MANUAL

TTG SERIES

FANS

TECSYSTEM S.r.l.

20094 Corsico (MI)

Tel.: [phone]

Fax: [phone]

http://www.tecsystem.it

R. 1.3 20/02/17

ENGLISH

1MN0069 Rev 0

“Translations of the original instructions”

operates with ISO9001 certified quality system

2

TTG240-300-360

INTRODUCTION

First of all thank you for choosing and using TECSYSTEM product, we strongly suggest you to read carefully this
instruction manual. It will allow you to understand how to use the system and take full advantage of all its features.

WARNING! THIS MANUAL IS VALID AND COMPLETE ONLY FOR THE FANS MODEL: TTG2 40, TTG300 AND
TTG360.

INDEX

PAGE

1) SAFETY REGULATIONS

………………………………… 3

2) TECHNICAL SPECIFICATIONS

……………………………….. 4

3) MAIN PARTS

………………………………… —

4) MOUNTING

………………………………… 5

•

SIZE FAN TTG240

………………………………… —

•

SIZE FAN TTG300

………………………………… 6

•

SIZE FAN TTG360

………………………………… 7

5) MOUNTING NOTES

………………………………… 8

•

POWER SUPPLY

………………………………… —

•

ENVIRONMENTAL CONDITIONS OF USE

………………………………… —

•

MAINTENANCE

………………………………… —

6) DIAGNOSTIC FAULT

………………………………… 9

7) WARRANTY CONDITIONS

………………………………… —

8) EQUIPMENT DISPOSAL

…………………………………. —

9) USEFUL CONTACTS

………………………………… —

3

TTG240-300-360

SAFETY REGULATIONS

WARNING:

Carefully read the manual before using the fan. Keep these instructions for future reference.

Do not touch /move fans while they are in operation: RISK INJURY.
The product must be installed in a location with limited access to qualified technician. Any work on the appliance

must be left to a qualified repair technician.

Do not touch the motor or power cables: contact with a voltage of 230/120 Volts AC can be fatal. To reduce the

risk of electric shock, do not disassemble or modify in any way the fan motor. Before connecting the device to
make sure that all connections have been made correctly. Always disconnect the fan from power supply before perfo rming
any type of maintenance.

Never touch the fan motor burns danger: RISK INJURY.

Failure to follow these instructions can cause damage, fire or electric shock, with possible serious injury!

POWER SUPPLY

Before using it make sure that the power supply wires are not damaged, kinked or crushed. Do not tamper with the power
supply wires. Never disconnect the power supply by pulling the cable, avoid touching the pins. Do not perform connection/
disconnection operations with wet hands. Do not use objects as levers to disconnect the power supply of the system.
Disconnect the power immediately if it is evident that the system gives off a burning smell or smoke, please contact
technical support Tecsystem.

LIQUIDS
Do not expose the product to dripping or splashing liquids. Do not allocate in places where humidity is over 90% and never
touch with wet hands.

CLEANING
Before cleaning the fan always disconnect the power supply. To avoid malfunctions, cleaning the fan only using
compressed air to remove dust and dirt. Do not use oils or fats of any kind.

OBJECTS
Never push objects through the air inlet or outlet, if this happens, disconnect the fan and call a technician.

RESTRICTED USE A COMPETENT PERSON
The product is a sophisticated electromechanical system, absolutely not suitable for use by untrained personnel.
All work must be performed by a qualified technician.

ACCESSORIES
Do not use accessories or replacement parts that are not original, it could cause damage to the fan and put at risk the
safety of the user. In case of failure, contact technical support.

LOCATION
Install the fan indoor protected from splashing water and sunlight. Do not place near heat sources exceed the
parameters specified in this manual. Place the fan in a horizontal and stable surface, away from vibration.
The product must be installed in a location with limited access to qualified technician.

REPAIR
Do not repair or adjust the fan. If any fault occure, do not hesitate to contact, always contact a qualified technician.
Opening the fan tampering involves the automatic invalidation of the warranty.

PRODUCTION
The date and the batch production of the device are shown on the label attached on the fan. Removing the label implies
the automatic invalidation of the warranty.

TECHNICAL SUPPORT

Mail: [e-mail] - tel: [phone]