TECshow Ion 132B User Manual

Download

Page 1

USER MANUAL

Read the user manual before turning on the product.

Page 2

Every person involved with the installation, operation and maintenance of this device has to

be qualified

follow the instructions of this manual

consider this manual to be part of the total product

keep this manual for the entire service life of the product pass this manual on to every further owner or user of the product download the latest version of the user manual from the Internet

CAUTION!

Keep this device away from rain and

moisture!

Unplug mains lead before opening the

housing!

For your own safety, please read this user manual carefully before you initially start-up.

INTRODUCTION

Unpack the device you will find following items inside the box:

1. The fixture device

2. User manual

3. Omega holder with quick-lock fastener

4. DMX cable 3m

5. PowerCon power supply cable 1.5m

6. Safety rope

SAFETY INSTRUCTIONS

This device has left our factory in absolutely perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual.

Thanks for choosing a TECSHOW product. ION Series is built to satisfy the most demanding users. We are confident that our excellent products and service will satisfy you.

Important:

Damages caused by the disregard of this user manual are not subject to warranty. The dealer

will not accept liability for any resulting defects or problems.

CAUTION!

Be careful with your operations. With a dangerous voltage you can suffer a

dangerous

electric shock when touching the

wires

Page 3

If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your device. Leave the device switched off until it has reached room temperature.

Please make sure that there are no obvious transport damages. Should you notice any damages on the A/C connection cable or on the casing, do not take the device into operation and immediately consult your local dealer.

This device falls under protection-class I. The power plug must only be plugged into a protection class I outlet. The voltage and frequency must exactly be the same as stated on the device. Wrong voltages or power outlets can lead to the destruction of the device and to mortal electrical shock.

Always plug in the power plug last. The power plug must always be inserted without force. Make sure that the plug is tightly connected with the outlet.

Never let the power-cord come into contact with other cables! Handle the power-cord and all connections with the mains with particular caution! Never touch them with wet hands, as this could lead to mortal electrical shock.

Never modify, bend, strain mechanically, put pressure on, pull or heat up the power cord. Never operate next to sources of heat or cold. Disregard can lead to power cord damages, fire or mortal electrical shock.

The cable insert or the female part in the device must never be strained. There must always be sufficient cable to the device. Otherwise, the cable may be damaged which may lead to morta

l damage.

Make sure that the power-cord is never crimped or damaged by sharp edges. Check the device and the power-cord from time to time.

If extension cords are used, make sure that the core diameter is sufficient for the required power consumption of the device. All warnings concerning the power cords are also valid for possible extension cords.

Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the power-cord by the plug. Never pull out th

e plug by tugging the power-cord. Otherwise, the cable or plug can be damaged leading to mortal electrical shock. If the power plug or the power switch is not accessible, the device must be disconnected via the mains.

If the power plug or the device is dusty, the device must be taken out of operation, disconnected and then be cleaned with a dry cloth. Dust can reduce the insulation which may lead to mortal electrical shock. More severe dirt in and at the device should only be removed by a specialist.

There must never enter any liquid into power outlets, extension cords or any holes in the housing of the device. If you suppose that also a minimal amount of liquid may have entered the device, it must immediately be disconnected. This is also valid, if the device was exposed to high humidity. Also if the device is still running, the device must be checked by a specialist if the liquid has reduced any insulation. Reduced insulation can cause mortal electrical shock.

There must never be any objects entering into the device. This is especially valid for metal parts. If any metal parts like staples or coarse metal chips enter into the device, the device must be taken out of operation and disconnected immediately. Malfunction or short-circuits caused by metal parts may cause mortal injuries.

HEALTH HAZARD!

Never look directly into the light source, as sensitive persons may suffer

epileptic shock (especially meant for

epileptics)!

Keep away children and amateurs! Never leave this device running unattended.

Page 4

OPERATING DETERMINATIONS

This device is a moving-head lighting effect for creating decorative effects. This product is only allowed to be operated with an alternating voltage of 100-240 V, 50/60 Hz and was designed for indoor use only.

This device is designed for professional use, e.g. on stages, in clubs, bars, theatres etc.

Lighting effects are not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects.

Do not shake the device. Avoid brute force when installing or operating the device.

Never lift the fixture by holding it at the projector-head, as the mechanics may be damaged. Always hold the fixture at the transport handles.

When choosing the installation-spot, please make sure that the device is not exposed to extreme heat, moisture or dust. There should not be any cables lying around. Please make sure that the unit cannot be touched or bumped.

This device must never be operated or stockpiled in surroundings where splash water, rain, moisture or fog may harm the device. Moisture or very high humidity can reduce the insulation and lead to mortal electrical shocks. When using smoke machines, make sure that the device is never exposed to the direct smoke jet and is installed in a distance of 0.5 meters between smoke machine and device. The room must only be saturated with an amount of smoke that the visibility will always be more than 10 meters.

The ambient temperature must always be between -15° C and +45° C. Keep away from direct insulation (particularly in cars) and heaters.

The relative humidity must not exceed 50 % with an ambient temperature of 45° C. This device must only be operated in an altitude between -20 and 2000 m over NN. Never use the device during thunderstorms. Over voltage could destroy the device. Always disconnect the device during thunderstorms.

The symbol

- -

-m

determines the minimum distance from lighted objects. The

minimum distance between light-output and the illuminated surface must be more than this value.

The device must only be installed on a non-flammable surface. In order to safeguard sufficient ventilation, leave 50 cm of free space around the device.

The housing must never touch surrounding surfaces or objects.

Make sure that the area below the installation place is blocked when rigging, derigging or servicing the fixture.

For overhead use (mounting height >100 cm), always fix the fixture with an appropriate safety-rope. Fix the safety-rope at the correct fixation po

ints only. The safety-rope must never be fixed at the transport handles!

Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened.

The maximum ambient temperature T

= 45° C must never be exceeded.

Operate the device only after having become familiarized with its functions. Do not permit operation by persons not qualified for operating the device. Most damages are the result of unprofessional operation!

Please use the original packaging if the device is to be transported. Please consider that unauthorized modifications on the device are forbidden due to safety reasons!

Never remove the serial barcode from the device as this would make the guarantee void. If this device will be operated in any way different to the one described in this manual, the product may suffer

Page 5

damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like shortcircuit, burns, electric shock, crash etc.

Page 6

DESCRIPTION OF THE DEVICE

Features

Source

 Light source: Osram Sirius HRI 132W discharge lamp  Lamp life: 10.000 hours  Luminous Flux: 6200lumen, 354200lux@5m  Control: Remote on/off via DMX  Ballast: switching mode power supply

Optical System  Beam angle: 2° X/Y

 Pan: 360° (2.8 sec) or 540°(2.0 sec), Tilt: 265° (1.8 sec)  3 phase motor for fast and quiet movement  16-bit resolution  Auto repositioning

Colors

 14+open, interchangeable, indexable and bidirectional rainbow effect  Color bounce

Gobos

 Outside 13.8mm, inside 6mm  17+ open static gobos  Real indexable and gobo shaking  Distinctive gobo animation effect

Features

 DMX channels: 13/15/16  Color wheel: 14+1 colors  Static gobo wheel: 17+1 gobos  Motorized focus  Full range 0-100% dimmer  Various strobe  8 facets rotating Effect wheel  RDM function to change DMX address, display flip, X/Y Reverse and so on  RDM read voltage, current, power consumption of lamp  Software upgrade via DMX  Hibernation when lost DMX for preset time  Indicate temperature info of base, arm and lamp  Fan speed auto change according to temperature

Display

 2.4inch super nice LCD display with friendly English menu  Auto lock  Flip  Back-up communicating IC

Power

 Max power consumption: 250W  Powercon in and out  Power supply: Electronic auto-ranging  Input voltage range: 100–240V, 50-60Hz

Dimension and Weight

 Fixture: 300X188X435MM  Packing: 510X370X270MM  Net Weight: 10KG  Gross Weight: 12KG

Page 7

5 6

Overview

(1) Objective lens (2) Arm (3) Base

! !

(4) Handle (5) Wireless indicator (6) Display (7) Microphone (8) Left button (9) Down buttom (10) Enter button (11) Up button (12) Right button

(13) 3-PIN DMX input socket (14) 3-PIN DMX output socket (15) Power input (16) Power output (17) Fuseholder

()*+! ,-./0!1.2345

Page 8

INSTALLATION

Installing/Replacing the lamp

! !

DANGER TO LIFE!

Only install the lamp with the device switched off! Unplug from mains before!

For the installation, you need one Osram Sirius HRI 132 W discharge lamp.

The lamp must only be changed when wearing appropriate protective clothing (protection glasses, protection gloves, helmet with sight, leather apron).

CAUTION!

The lamp has to be replaced when it is damaged or deformed due to the heat!

The lamp life given by the manufacturer must never be exceeded. This is why you need to take notes on the operational time of the lamp or check the operating hour meter regularly and replace the lamp in time.

Keep exchanged lamp in a protective container and remove accordingly. During the operation, the lamp reaches temperatures of up to 600° C.

Before replacing the lamp, unplug mains lead and let the lamp cool down (approx. 10 minutes).

During the installation do not touch the glass-bulbs bare-handed! Please follow the lamp manufacturer's notes!

Do not install lamps with a higher wattage! Lamps with a higher wattage generate temperatures the device was not designed for. Damages caused by non-observance are not su

bject to warranty.

Procedure:

Step 1: Unscrew the eight housing screws (standard Philips screws) of the projector head cover and

remove the projector head cover.

Step 2: Unscrew the fixation screws A and B of the lamp system and carefully remove the cover from the

housing.

Step 3: Unscrew the fixation screw of the lamp holder. Step 4: Push the plate to the right side. Step 5: If replacing the lamp, remove the old lamp from the lamp holder. First of all, carefully detach the

two connection wires from the lamp base. Carefully remove the lamp from the lamp holder.

Step 6: Carefully insert the new lamp into the lamp holder. Carefully attach the two connection wires onto

the lamp base. Please make sure that the new lamp is in the same position as the old lamp before closing the device.

Step 7: Replace the lamp system in the housing and tighten the fixation screws. Step 8: Replace the pojector head cover and tighten the srews.

Page 9

Attention: Please note, the Osram Sirius HRI 132 W lamp is not a hot-restrike type. You must wait

approximately 10 minutes before you can attempt to strike the lamp once it has been

turned off!

Do not operate this device with opened cover!

Inserting/Exchanging gobos

DANGER!

Install the gobos with the device switched off

only.

Unplug from mains

before!

If you wish to use other forms and patterns as the standard-gobos, or if gobos are to be exchanged, please follow the instructions below:

CAUTION!

Never unscrew the screws of the rotating

gobo

as the ball bearing will otherwise be

opened!

Rigging

The installation of the projector has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation.

The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net. This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails.

When rigging, derigging or servicing the fixture staying in the area below the installation place, on bridges, under high working places and other endangered areas is forbidden.

The operator has to make sure that safety-relating and machine-technical installations are approved by an expert before taking into operation for the first time and after changes before taking into operation another time.

The operator has to make sure that safety-relating and machine-technical installations are approved by an expert after every four year in the course of an acceptance test.

The operator has to make sure that safety-relating and machine-technical installations are approved by a skilled person once a year.

Procedure: The projector should be installed outside areas where persons may walk by or be seated.

IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including (but not limited to) calculating working load limits, installation material being used, and periodic safety inspection of all installation material and the projector. If you lack these qualifications, do not attempt the installa

tion yourself,

but instead use a profess

ional structural rigger. Improper installation can result in bodily injury and.or

damage to property.

Page 10

)7!

The projector has to be installed out of the reach of people.

If the projector shall be lowered from the ceiling or high joists, professional trussing systems have to be used. The projector must never be fixed swinging freely in the room.

Caution: Projectors may cause severe injuries when crashing down! If you have doubts concerning the safety of a possible installation, do NOT install the projector!

Before rigging make sure that the installation area can hold a minimum point load of 10 times the projector's weight.

DANGER

FIRE!

When installing the device, make sure there is no

highly-inflammable

material (decoration articles, etc.) within a distance of min. 0.5

CAUTION!

Use an appropriate clamp to rig the fixture on the

truss.

Follow the instructions mentioned at the bottom of the

base.

Make sure that the device is fixed properly! Ensure

that

the structure (truss) to which you are attaching the fixtures is

secure.

The Moving-Head can be placed directly on the stage floor or rigged in any orientation on a truss without altering its operation characteristics (see the drawing).

The fixture’s base enables to be mounted in two ways.

For overhead use (mounting height >100 cm), always install an appropriate safety bond.

Please note: for overhead rigging in public or industrial areas, a series of safety instructions have to be followed that this manual can only give in part. The operator must therefore inform himself on the current safety instructions and consider them.

Page 11

))!

The manufacturer cannot be made liable for damages caused by incorrect installations or insufficient safety precautions!

Install the safety bond by inserting the quick link in the hole on the bottom of the base. Pull the safety bond over the trussing system etc. Insert the end in the quick link and tighten the fixation screw.

The maximum drop distance must never exceed 20 cm.

A safety bond which already hold the strain of a crash or which is defective must not be used again.

DANGER

LIFE!

Before taking into

operation

for the first time, the

installation

has to be

approved

by an

expert!

2 3

(1)

Omega-holder

(2)

Clamp 1

(3)

Safety-rope

(4)

Quick-lock fastener

Screw the clamp via a M12 screw and nut onto the Omega-holder.

Insert the quick-lock fasteners of the Omega-holder into the respective holes on the bottom of the device. Tighten the quick-lock fasteners fully clockwise.

Page 12

)"!

DMX-512 connection / connection between fixtures

Projector 1 Projector 2 Projector 3

Starting address 1 Starting address 20 Starting address 39

120 Ohms DMX-512 Controller

The wires must not come contact with each other, otherwise

the fixtures will not work at all, or will not work properly.

Please note, the starting address depends upon which controller is being used.

Only use a DMX-cable and 3-pin XLR-plugs and connectors in order to connect the controller with the fixture or one fixture with another.

Occupation of the XLR-connection:

If you are using controllers with this occupation, you can connect the DMX-output of the controller directly with the DMX-input of the first fixture in the DMX-chain. If you wish to connect DMX-controllers with other XLR-outputs, you need to use adapter-cables.

Building a serial DMX-chain:

Connect the DMX-output of the first fixture in the DMX-chain with the DMX-input of the next fixture. Always connect one output with the input of the next fixture until all fixtures are connected.

Caution: At the last fixture, the DMX-cable has to be terminated. Plug the terminator with a 120 Ω resistor between Signal (–) and Signal (+) in the DMX-output of the last fixture.

Page 13

)#!

Connection with the mains

Connect the device to the mains with the enclosed power supply cable.

The occupation of the connection-cables is as follows:

Cable

International

Brown

Live

Blue

Neutral

Yellow/Green

Earth

The earth has to be connected!

If the device will be directly connected with the local power supply network, a disconnection switch with a minimum opening of 3 mm at every pole has to be included in the permanent electrical installation.

The device must only be connected with an electric installation carried out in compliance with the IECstandards. The electric installation must be equipped with a Residual Current Device (RCD) with a maximum fault current of 30 mA.

Lighting effects must not be connected to dimming-packs.

The device is equipped with a lockable power input connector. Plug in the power cord and turn it to the right until it locks. Plug the power cord into a grounded electrical outlet that matches the rated voltage of the machine.

OPERATION

With the power switch, you can switch the device on and off. After you connected the effect to the mains, the fixture starts running. During the reset, the motors are trimmed and the device is ready for use afterwards.

Stand Alone operation

In the Stand Alone mode, the model can be used without controller.

Disconnect the fixture from the controller and call the internal program. Please refer to the instructions under Control Board.

DMX-controlled operation

You can control the projectors individually via your DMX-controller. Every DMX-channel has a different occupation with different features. The individual channels and their features are listed under DMX-protocol.

Addressing

The Control Board allows you to assign the DMX starting address, which is defined as the first channel from which the fixture will respond to the controller.

If you set, for example, the address to channel 20, the fixture will use the channel 20 to 38 for control.

Please, be sure that you don’t have any overlapping channels in order to control each fixture correctly and independently from any other fixture on the DMX-chain. If several fixture are addressed similarly, they will work synchronically.

Press the Up/Down-buttons for setting the desired starting address. Now you can start operating the fixture via your lighting controller.

Page 14

)$!

Note: After switching on, the device will automatically detect whether DMX 512 data is received or not. If there is no data received at the DMX-input, the display will flash.

This situation can occur if:

the XLR plug (cable with DMX signal from controller) is not connected with the input of the device.

the controller is switched off or defective, if the cable or connector is defective or the signal wires

are

swap

in the input connector.

Note: It’s necessary to insert the XLR termination plug (with 120 Ohm) in th

e last lighting in the link in order

to ensure proper transmission on the DMX data link.

DMX-protocol

Channe

name

function

Min

DMX

Max

DMX

Ex1

Ex 2

1 1 1

Pan

Pan Coarse

255

2 2

Pan fine

Pan Fine

255 2 3

Tilt

Tilt Coarse

255

4 4

Tilt fine

Tilt Fine

255

3 5 5

Movment Speed

fastest to Slowest

255

Movment Function

Normal

Movement With Backout

TBD

255

4 6 7

Shutter Function

Normal Shutter Functions

Pulse-effect Forward

Pulse-effect Reverse

Random Strobe

TBD

255

5 7 8

Shutter

Normal Shutter Functions

Strobe Rate (slow to fast)

223

Open

224

255

Pulse-effect Forward

Strobe Rate (slow to fast)

223

Open

224

255

Pulse-effect Reverse

Strobe Rate (slow to fast)

223

Open

224

255

Random Strobe

Strobe Rate (slow to fast)

223

Open

224

255 6 8

Dimmer

Dimmer(Close to Open)

255 7 9

Color

Indexed

Page 15

)%!

Function

Indexed With BackOut

Forward Spin

Reverse Spin

Continuous

Color Bounce

111

TBD

112

255

Color

Indexed & Indexed With BackOut&Color Bounce

Position 1 (Open)

Position 2

Position 3

Position 4

Position 5

Position 6

101

Position 7

102

118

Position 8

119

135

Position 9

136

152

Position 10

153

169

Position 11

170

186

Position 12

187

203

Position 13

204

220

Position 14

221

237

Position 15

238

255

Forward Spin

Stop to fastest

255

Reverse Spin

Stop to fastest

255

Continuous

Positioning from 0-360 degrees

255

Gobo Function

Indexed

Indexed With BackOut

Forward Spin

Reverse Spin

Continuous

Shake

TBD

255

Gobo

Indexed & Indexed With Backout&Shake

Position 1 (Open)

Position 2

Position 3

Position 4

Position 5

Position 6

Position 7

Position 8

111

Position 9

112

125

Position 10

126

139

Position 11

140

153

Position 12

154

167

Position 13

168

181

Page 16

)&!

Position 14

182

195

Position 15

196

209

Position 16

210

223

Position 17

224

237

Position 18

238

255

Forward Wheel Spin

Stop to fastest

255

Reverse Wheel Spin

Stop to fastest

255

Continuous

Positioning from 0-360 degrees

255

Prism & Prism Rot

Prism

Position 1 (Open)

Prism Rot Forward Spin

Stop to fastest

127

Prism Rot Reverse Spin

Stop to fastest

128

255

Focus

Continuous

Focus In to Focus Out

255

Control

Normal

Reset All

Pan&Tilt Reset

Color Reset

Gobo Reset

Shutter Reset

Other Reset

Display Off

Display On

Lamp Off

Lamp On

Hibernation

TBD

255

Control Board

The Control Board offers several features: you can simply set the starting address, run the pre-programmed program or make a reset.

The main menu is accessed by pressing Enter until the display is lit. Browse through the menu by pressing the arrow buttons (up, down, left, right). Press Enter in order to select the desired menu. You can change the selection by pressing the arrow buttons. Press Enter in order to confirm. The functions provided are described in the following sections.

Default settings shaded. 1 Basic Reload / 2 Program Reload / 3 Private Reload

8-99/4

:;<!=>>0/11①!

<<<!

:;<!?>>0/11!1/3329@!

A20/B/11①!

A20/B/11!C9?DB/>!

E2@53!

FG09!H9IHJJ!

HKIHLL!

E?MN!H9!

=G3-M?324!

HKIHLL!

E?MN!H9I-JJ!.5/9!N-./0!

-9!

Page 17

)'!

:;<!8-930-B!

HKIHLL!

:;<!4-930-B!-0!9-3!

;?O! F/MN/0?3G0/①!

*7P)#6℃Q!)"7℃! I)'&P"*"℉,!"$*℉!

E?MN!-JJ!2J! 3/MN/0?3G0/! 4-9329G-G1BR!-S/0! J-0!%!M29G3/1!

E?MN!=>TG13①!

,=KUU!

=>TG13!S?BG/!-J! 45?99/B!

V9J-0M?32-9!

F2M/!V9J-W!

8G00/93! ! ! ! ! ! <<<<(X-G01+! L2O3G0/!E2J/! ! <<<<(X-G01+!

L2O3G0/!D--3!32M/! L2O3G0/!3-3?B!0G9! 32M/!

E?MN!V9J-W!

Y-B3?@/! 8G00/93! ,-./0!

XV:!E?MN! V9J-0M?32-9!

F/MN/0?3G0/!

K/?0!E?MN!F/MN!!(>/N/9>1!-9!J2O3G0/+!

F/MN/0?3G0/! Z/91-01!

L?91!ZN//>!

K/?0!E?MN!L?9!!(>/N/9>1!-9!J2O3G0/+!

L?9!1N//>!Z/91-01!

85?99/B!Y?BG/!

,=KUU!

:21NB?R!S?BG/!-J! 45?99/B!

C00-0!;/11?@/!

,?9QF2B3UU!

C00-0!45?99/B1!

L2O3G0/!;->/B!

OOOOOOOOOOOO!

:21NB?R!M->/B!D0?9> ! ?9>!M->/B!

Z-J3.?0/!Y/0!

)[7)! ! Y)W7W77!

"[7)! ! Y)W7W77!

Y/012-9!-J!/?45!V8!

Z/3!

]/1/3!

=BB! ,?9^F2B3! 8-B-01! _-D-1! Z5G33/0! H35/01!

]/1/3!?BB! ! ]/1/3!,?9^F2B3! ]/1/3!8-B-01! ]/1/3!_-D-1! ]/1/3!Z5G33/0! ]/1/3!H35/01

;-SM/93!

,?9!]/S/01/①! F2B3!]/S/01/①! ,?9!:/@0//①! C94->/01①! ,?9IF2B3!;->/①!

HKIHLL! HKIHLL! I%$7! HKIHLL! Z3?9>IZM--35!

,?9!]/S/01/! F2B3!]/S/01/! 85--1/!,?9!:/@0//! C94->/0!.5//B!

-9I-JJ! 85--1/!N?9I32B3! M->/!

[V!Z/3!

;24!Z/91W ③! K-!Z2@9?B①! F/MN/0?3G0/W!8IL① L?91!;->/①!

X2D/09?32-9①! `?4aB2@53①! LB2N!:21NB?R① :21NB?R!`02@53③ `0?9>!Z5-.①! b/R!E-4a①!

7P66cQ&7c! 8B-1/IX-B>I=G3-I;G124! L?50/95/23I8/B12G1! =G3-!ZN//>!IX2@5!ZN//>!

HLLQ!7);P66;，)%;! 7"P&7M!7"M! HKIHLL! 77P#)!)7! HKIHLL! HKIHLL!

Z/91232S23R!-J!;24! ;->/!.5/9!9-! 12@9?B! F/MN/0?3G0/!?3! ℃I ℉!

L?91!M->/! ZB//N29@!M->/!

Z5-.!D?4aB2@53!32M/ :21NB?R!)*7° 0/S/01/! :21NB?R!`02@539/11 Z5-.!D0?9>!-0!9-3! b/R!B-4a!-9I-JJ

Page 18

)*!

[1/01!

[1/0!;->/①!

Z3?9>?0>! CO3/9>/>!)! CO3/9>/>!"! [1/0!

Z3?9>?0>! M->/()&D23+! CO3/9>/>!M->/!)! CO3/9>/>!M->/!"! [1/0!N0-@0?M!M->/!

C>23![1/0③!

;?O!85?99/B!d!<<! ,=K!d!8X7)!

C>23!G1/01!M->/!

8?B2D0?32-9③!

e,?11.-0>e! 8-B-0!

d<<<! d<<<!

,?11.-0>\!7%7! 8?B2D0?3/!45?99/B! S?BG/

L2O3G0/!V:③!

K?M/! e,?11.-0>e! ,V:!8->/!

K?M/! ,?11.-0>\!7%7! Z/3!,V:!-J!]:;!

A20/B/11!Z/3①!

:;<!H9!8?DB/! ]/1/3!8-99/43!

HKIHLL! HKIHLL!

:;<!Z/9>!HG3! ]/1/3!8-99/43!

]/B-?>!:/J?GB3!

`?124!]/B-?>(①+! ,0-@0?M!]/B-?>(②+! eee,?11.-0>eee! ,02S?3/!]/B-?>(③+! =BB!]/B-?>!

HKIHLL! HKIHLL! <<<! HKIHLL! HKIHLL!

`?124!]/B-?>! ,0-@0?M!]/B-?>! ,?11.-0>\!7%7! ,02S?3/!]/B-?>! =BB!]/B-?>!

,0-@0?M!

,B?R①!

:;<!]/4/2S/! ZB?S/!]/4/2S/! Z/fG/94/! ;G124!

! ZB?S/!]/4/2S/!)Q"Q#! ;?13/0!I!=B-9/! ;?13/0!I!=B-9/!

:;<!]/4/2S/! 85--1/!1B?S/! N-1232-9! ]G9!Z/fG/94/! ;G124!M->/!

Z/B/43!85?1/②!

85?1/!,?03!)! 85?1/!,?03!"! 85?1/!,?03!#!

85?1/!)!P!*! ! 85?1/!)! 85?1/!)!P!*! ! 85?1/!"! 85?1/!)!P!*! ! 85?1/!#!

Z/B/43!?9>!0G9!?G3-! N0-@0?M!

C>23!85?1/②!

85?1/!)! :! ! 85?1/!*!

85?1/!F/13! Z3/N!7)! Z3/N!&$!

! dZ8OOO! dZ8OOO!

F/13! `/@29929@!14/9/! C9>29@!14/9/!

C>23!Z4/9/1②!

C>23!Z4/9/!77)! P!C>23!Z4/9/! "%7!

,?9QF2B3QUU! eeL?>/!F2M/ee! eeZ/49/! F2M/ee! :;<!V9NG3!

dOOO! dOOO! dOOO!

V9NG3!M?9G?B!14/9/ ! ;->2JR!M?9G?BBR! J?>29@!32M/! ;->2JR!M?9G?BBR!

14/9/!32M/! V9NG3!14/9/!J0-M! /O3/02-0!4-930-BB/0!

Z4/9/1!]/4-0>!

Z4<<dgZ4<<!

=G3-!V9NG3!14/9/1!

Connect

DMX address setting

With this function, you can adjust the desired DMX-address via the Control Board. Select “DMX Address“ by pressing Up or Down. Press the Enter-button, adjust the DMX address by pressing Up or Down. Press the Enter-button to confirm.

Wireless With this function, you can enter wireless mode, then no need signal cable connection, in this mode signal still transmitted by cable if the signal cables are connected, if want to send signal via wireless

Page 19

)6!

cables must be disconnected.

Light

MaxTemperate

With this function you can set the inside temperature at which the projector will automatically switch the lamp off. Press Up or Down to select the maximum inside temperature between 80 °C and 139 °C. Inside temperatures below 90 °C are not critical. 90 °C and more should lead to the lamp being switched off. Please note that the outside temperature should not exceed 45 °C.

Information

Time information Current

With this function, you can display the temporary running time of the device from the last power on. The display shows “XXXX”, “X“ stands for the number of hours. The counter is reset after turning the device off.

Fixture Life

With this function, you can display the running time of the device. The display shows “XXXX”, “X“ stands for the number of hours.

Temperature Near lamp Temp

With this function you can display the temperature in the projector-head in degree Celsius/degree Fahrenheit. ...

Fan speed With this function you can display the current fan speed. The display shows “XXXX”, “X“ stands for Hz.

Initial status With this function, you can display with which value the respective channels will start.

Error channels With this function, you can display the channel errors.

Fixture Model With this function, you can display the model number and brand of the fixture.

Software version With this function you can display th

e software version of each IC.

•

Select “Software ver.” by pressing Up or Down.

•

Press the Enter-button, the display shows e.g. “1U01 VX.X.XX”, “X.X.XX“ stands for the version number.

Set

Reset With this function you can reset the device via the Control Board. You can select the different Resetfunctions by pressing Up or Down.

Movement PAN Reverse

With this function you can reverse the PAN-movement.

TILT Reverse With this function you can reverse the TILT-movement.

PAN degree With this function you can select the PAN-degree.

•

Select “PAN degree” by pressing Up or Down.

•

Press the Enter-button, the display shows “540”.

•

Press Up or Down to select the desired degree between “540” and “630”.

Page 20

•

Press the Enter-button to confirm.

Automatic PAN/TILT calibration With the function "Encoders" you can calibrate the PAN/TILT movement to the correct starting position.

Adjust PAN/TILT speed With this function you can define the PAN/TILT speed. You can select one of two different modes.

UI Set

Mic sensitivity

With this function, you can select the desired microphone sensitivity between 0 % and 99 %.

•

Select “Mic Sens” by pressing Up or Down.

•

Press the Enter-button.

•

Press Up or Down to select the desired sensitivity.

•

Press the Enter-button to confirm.

No DMX status With the function "No Signal", you can set different modes if there is no DMX-signal.

•

Select "Close, Hold, Auto or Music" by pressing Up or Down.

•

Press Up or Down to select between "Close", "Hold", "Auto" or "Music".

•

Press the Enter-button to confirm.

Select temperature designation With this function you can select the temperature designation.

•

Select “Temperature C/F” by pressing Up or Down.

•

Press Up or Down to select the desired degree between “Celsius” and “Fahrenheit”.

•

Press the Enter-button to confirm.

Hibernation - power standby mode With this function you can put the device in the power standby mode. This function will be automatically activated after a predefined period of time of no DMX activity. In standby mode the lamp/LEDs and all motors will power down if no DMX signal is sent to the fixture for a period of e. g. 15 minutes (can be user defined). The fixture will automatically reset and return to normal operation once a DMX signal is sendet.

Backlight With this function you can shut off the display after 2 to 60 minutes.

Flip Display With this function you can flip the display by 180° for a better view when the fixture is hung from the truss or a

ceiling. Short-cut: Press “up” and “down” for three seconds to flip the display directly.

Brand Show With this function you can show or hide the brand name 'TECSHOW' on the display during menu operation, but still show it after reset.

Key lock With this function you can lock the keys of the Control Board to e.g. prevent menu tampering. If this function is activated, the keys will be automatically locked as soon as exit the menu. In order to deactivate or temporarily deactivate the keylock function, press the button UP-DOWN-LEFT-RIGHT-ENTER regain access to the menu commands.

Users

User mode

With this function, you can create user defined channel orders.

Edit User With this function, you can adjust the Preset user defined channel order.

Calibration With this function, you can calibrate and adjust the effect wheels to their correct positions. The password for this function is “050“.

Page 21

")!

Fixture ID

RDM

With this function you can call up various submenus via RDM.

This device is RDM ready. RDM stands for "Remote Device Management" and makes remote control of devices connected to the DMX-bus possible. ANSI E1.20-2006 by ESTA specifies the RDM standard as an extension of the DMX512 protocol.

Manual settings like adjusting the DMX starting address are no longer needed. This is especially useful when the device is installed in a remote area.

RDM is integrated in DMX without influencing the connections. The RDM-data is transmitted via the standard XLR-poles 1 and 2 – new DMX-cables are not necessary. RDM ready and conventional DMX devices can be operated in one DMX line. The RDM protocol sends own packages in the DMX512 data feed and does not influence conventional devices.

If DMX splitters are used and RDM control is to be used, these splitters must support RDM.

The number and type of RDM parameters depend on the (optional) RDM controller being used.

RDM Parameter ID's (Slot 21-22)

Value

Category _Network Management

DISC_UNIQUE_BRANCH

0x0001

DISC_MUTE

0x0002

DISC_UN_MUTE

0x0003

Category -RDM Information

SUPPORTED_PARAMETERS

0x0050

PARAMETER_DESCRIPTION

0x0051

Category _Product Information

DEVICE_INFO

0x0060

DEVICE_MODEL_DESCRIPTION

0x0080

MANUFACTURER_LABEL

0x0081

DEVICE_LABEL

0x0082

FACTORY_DEFAULTS

0x0090

SOFTWARE_VERSION_LABEL

0x00C0

Category -DMX512 Setup

DMX_PERSONALITY

0x00E0

DMX_PERSONALITY_DESCRIPTION

0x00E1

DMX_START_ADDRESS

0x00F0

SLOT_INFO

0x0120

SLOT_DESCRIPTION

0x0121

Category _Sensors

SENSOR_DEFINITION

0x0200

SENSOR_VALUE

0x0201

Category _Power/Lamp Settings

0x04xx

DEVICE_HOURS

0x0400

Category -Display Settings

DISPLAY_INVERT

0x0500

Category _Configuration

PAN_INVERT

0x0600

TILT_INVERT

0x0601

Category _Control

IDENTIFY_DEVICE

0x1000

RESET_DEVICE

0x1001

Reload Default With this function you can restore the factory settings of the device. The different settings (marked in the table) will be set back to the default values (shaded).

Program

Play Slave Revice

Page 22

""!

With this function, you can define the device as slave. You can choose one of three different Slave programs. For further information see „Edit Chase”.

Sequence With this function, you can run the internal program. You can select the desired program under “Select Chase”. You can set the number of steps under “Edit Chase”. You can edit the individual scenes under “Edit Scenes”. With this function, you can run the individual scenes either automatically, i.e. with the adjusted Step-Time. The selection "Alone" means St

and

Alone-mode and "Master" that the device is defined as master.

Music With this function, you can run the internal program sound-controlled. The selection "Alone" means Stand Alone-mode and "Master" that the device is defined as master.

Select chase for auto program With this function, you can select the program for the Program Run.

Edit chase With this function, you can edit the internal programs.

Edit scenes With this function, you can edit the scenes of the internal programs.

Rec. Controller The device feat

ures an integrated DMX-recorder by which you can transmit the programmed scenes from your DMX-controller to the device. Adjust the desired scene numbers by pressing Up or Down (from – to). When you call up the scenes at your controller, they will automatically be transmitted to the device.

Excursion: A Master unit can send up to 3 different data groups to the Slave units, i.e. a Master unit can start 3 different Slave units, which run 3 different programs. The Master unit sends the 3 program parts in a continuous loo

The Slave unit receives data from the Master unit according to the group which the Slave unit was assigned to. If e.g. a Slave unit is set to „Slave 1“ in the menu „Set to Slave“, the Master unit sends „Auto Program Part 1“ to the Slave unit. If set to „Slave 2“, the Slave unit receives „Chase Part 2“.

To start a Auto Program please proceed as follows:

1.Slave-Setting

•

Select “Program” by pressing Up or Down.

•

Press the Enter-button to confirm.

•

Select “Slave” by pressing Up or Down.

•

Press the Enter-button to confirm.

•

Press Up or Down to select “Slave 1”, “Slave 2” or “Slave 3”.

•

Press the Enter-button to confirm.

Automatic Program Run

•

Select “Program” by pressing Up or Down.

•

Press the Enter-button to confirm.

•

Select “Sequence” by pressing Up or Down.

•

Press the Enter-button to confirm.

•

Press Up or Down to select “Master” or “Alone”. The selection "Alone" means Stand Alone-mode and

"Master" that the device is defined as master.

•

Press the Enter-button to confirm.

Program for Select Chase

•

Select “Edit Chase” by pressing Up or Down.

•

Press the Enter-button to confirm.

•

Select “Select Chase” by pressing Up or Down.

•

Press the Enter-button to confirm.

•

Press Up or Down to select “Chase Part 1”, “Chase Part 2” or “Chase Part 3”, and thus

select which Slave program is to be sent. Selection „Part 1“ means, that the Slave unit runs the same program as the master units.

•

Press the Enter-button to confirm.

Page 23

"#!

Program selection for Edit Program

•

Select “Edit Chase” by pressing Up or Down.

•

Press the Enter-button to confirm.

•

Select “Edit Chase” by pressing Up or Down.

•

Press the Enter-button to confirm.

•

Press Up or Down to select the desired program. With this function you can edit specific scenes

into a

specific program.

•

Press the Enter-button to confirm.

Automatic Scene Recording

•

Select “Edit Chase” by pressing Up or Down.

•

Press the Enter-button to confirm.

•

Select “Edit scenes” by pressing Up or Down.

•

Press the Enter-button to confirm.

•

Press Up or Down to select the desired scene numbers. You can program a maximum number of

250

scenes.

•

Press the Enter-button to confirm.

•

Press Up or Down to select the desired value.

•

Press the Enter-button to confirm.

Example:

Program 2 includes scenes: 10, 11, 12, 13; Program 4 includes scenes: 8, 9, 10 and Program 6 includes scenes: 12, 13, 14, 15, 16

Chase Part 1 is Program 2; Chase Part 2 is Program 3; Chase Part 3 is Program 6

The 3 Slave groups run the Auto Program in certain time segments, as shown in the following picture:

Error Messages

When you turn on the fixture, it will make a reset first. The display may show an error message while there are problems with one or more channels. The error message stands for the channels equipped with a testing sensor.

For example, when the display shows “Err channel PAN”, it means there is some error in the horizontal movement (PAN), control-channel 1. If there are some errors on several channels at the

Page 24

"$!

same time, you may see the error messages flash repeatly for 2 times, and then the fixture will generate a reset signal, all the stepper motors will reset. If the error messages maintain after performing reset more than 2 times, only the channels which have errors can not work properly, others can work as usual.

The respective error message will appear after the reset of the fixture if the channels magnetic-indexing circuit malfunction (sensor failed or magnet missing) or the stepping-motor is defective (or its driving IC on

the

main PCB). The channel feature is not located in the default position after the reset.

The different error messages are:

PAN

Color Wheel

Rotating gobo wheel

focus

TILT

Prism Rotation

CLEANING AND MAINTENANCE

The operator has to make sure that safety-relating and machine-technical installations are inspected by an expert after every four years in the course of an acceptance test.

The operator has to make sure that safety-relating and machine-technical installations are inspected by a skilled person once a year.

The following points have to be considered during the inspection:

All screws used for installing the devices or parts of the device have to be tighly connected and must not be

corroded.

There must not be any deformations on housings, fixations and installation spots (ceiling, suspension,

trussing).

Mechanically moved parts like axles, eyes and others must not show any traces of wearing (e.g. material

abrading or damages) and must not rotate with unbalances.

The electric power supply cables must not show any damages, material fatigue (e.g. porous cables) or

sediments. Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and

any safety problems have to be removed.

DANGER

LIFE!

Disconnect from mains before starting maintenance

operation!

We recommend a frequent cleaning of the device. Please use a moist, lint-free cloth. Never use alcohol or solvents!

CAUTION!

The lens has to be replaced when it is obviously

damaged,

so that its function is impaired, e. g. due to cracks or deep

scratches!

The objective lens will require weekly cleaning as smoke-fluid tends to building up residues, reducing the light-output very quickly. The cooling-fans should be cleaned monthly.

The interior of the fixture should be cleaned at least annually using a vacuum-cleaner or an air-jet.

There are no serviceable parts inside the device. Maintenance and service operations are only to be carried out by authorized dealers.

Replacing the fuse

If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.

Page 25

"%!

Before replacing the fuse, unplug mains lead.

Procedure:

Step 1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing (anti-

clockwise).

Step 2: Remove the old fuse from the fuse holder. Step 3: Install the new fuse in the fuse holder. Step 4: Replace the fuse holder in the housing and fix it.

Should you need any spare parts, please use genuine parts.

If the power supply cable of this device becomes damaged, it has to be replaced by a special power supply cable available at your de

aler.

Should you have further questions, please contact your dealer.

TECHNICAL SPECIFICATIONS

Power supply:

100-240 V AC, 50/60 Hz ~

Power consumption:

190 W

DMX control channels:

13/15/16

DMX512 connection:

3-pin XLR

Sound-control:

via built-in microphone

Type of sources:

Osram Surius 132w HID lamp

Beam angle:

approx.2.5°

Color-wheel:

14 dichroic filters plus open

Fixed gobo-wheel:

17 gobos and open

Maximum PAN-movement:

630°

Maximum TILT-movement:

270°

Dimensions (LxWxH):

250x 300 x 400 mm

Weight:

10kg

Maximum ambient temperature Ta:

45° C

Maximum housing temperature TB (steady state):

60° C

Min.distance from flammable surfaces:

0.5 m

Min.distance to lighted object:

2 m

Fuse:

T 3.15 A, 250 V

Please note: Every information is subject to change without prior notice. 10.07.2013