
© 2015 TE Connectivity family of companies
All Rights Reserved
*Trademark
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.
PRODUCT INFORMATION
1-800-522-6752
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com.
INPUT VOLTAGE AND
FREQUENCY RANGE
CURRENT REQUIREMENT (PLUG TYPE)
4.5 a (NEMA 1-15)
2063870-2
China, Australia, New Zealand
Operating Temperature Range:
25 Minutes (Approximately)
Operating Temperature Range:
Battery Chargers 2063870-[ ],
2280961-1, and AC-to-DC Power
Adapters 2063874-[ ]
Instruction Sheet
408-10363
07 AUG 15 Rev B
Figure 1
1. INTRODUCTION
Battery Chargers 2063870-[ ], 2280961-1, and AC-to-DC Power Adapters 2063874-[ ] are designed to be used
with the electro-hydraulic hand tool included in Electro-Hydraulic Hand Tool Kits 2031400-[ ]. The battery
charger is used to recharge Battery 2031440-1 (included with the hand tool kit). The AC-to-DC power adapter
enables the hand tool to be used without the battery.
For operating procedure and safety precautions for the hand tool kit, refer to Customer Manual 409-10095.
NOTE
The battery charger is also included with the hand tool kit, and the AC-to-DC power adapter is only available separately.
NOTE
All numerical values in this instruction sheet are in metric units [with U.S. customary units in brackets]. Figures are for
reference only and are not drawn to scale.
2. DESCRIPTION
See Figure 1 for features of the battery charger and power adapter. Specifications for the battery chargers and
power adapters are given in Figure 2.
Figure 2
1 of 3

3. SAFETY PRECAUTIONS
The following safety precautions apply to the battery charger and the power adapter.
Check the cord and plug for damage. DO NOT use the unit if damage is evident.
Check that the voltage of the power source is within the allowable voltage indicated on the unit label.
Keep metal objects away from the terminals; otherwise, shorts may occur.
DO NOT open the housing of the unit (there are no serviceable parts inside).
Use and store the unit in dry areas only. Protect the unit from moisture and dampness.
Use the unit only within the allowable operating temperature range (see Figure 2). Keep the unit out of
direct sunlight and away from heat sources.
4. OPERATING PROCEDURE
4.1. Battery Charger
NOTE
A new battery or one that has not been used for some time might require up to 5 charge-and- discharge cycles to reach its
normal capacity.
1. Plug the battery charger into the power source. Facing the front of the battery charger, observe the
state of the light-emitting diode (LED) located on the left side:
continuous red glow - charger ready to operate
408-10363
flashes red - internal malfunction (replace the battery charger, refer to Section 5)
2. If the battery charger is ready to operate, slide the battery onto the battery charger. Within 4 seconds,
the battery will be tested for adequate voltage, temperature, polarity, and short-circuit conditions.
Facing the front of the battery charger, observe the state of the LED located on the right side:
continuous green glow - charging in process
flashes green - battery is fully charged
flashes red - battery is over-heated (charging will resume when battery temperature drops to allowable
temperature)
continuous red glow - battery is defective
DANGER
DO NOT USE a damaged or defective battery. Properly dispose of the battery.
NOTE
The battery can remain on the battery charger plugged into the power source indefinitely without damage (overcharging will
not occur). If the battery is kept on the battery charger, and the battery charger is unplugged, the battery will lose the charge.
4.2. Power Adapter
1. Slide the power adapter onto the hand tool until it is securely held by the latch.
2. Plug the power adapter into the power source. Observe the red-colored LED located on the power
adapter:
continuous red glow - adapter ready to operate
3. When usage of the hand tool ends, unplug the power adapter from the power source, and observe the
red-colored LED located on the power adapter:
stops glowing (could take several minutes) - power adapter can be removed from the hand tool as
follows:
a. depress the latch
b. slide power adapter off of the hand tool
Rev B

408-10363
5. REPLACEMENT AND REPAIR
Order additional battery chargers and power adapters through your TE Representative, or call 1-800-522-6752
or write to:
CUSTOMER SERVICE (038-035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG PA 17105-3608
6. REVISION SUMMARY
Added new battery charger number to table in Figure 1
Rev B

Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
TE Connectivity:
2063874-1