TecnoVideo SSH254-L, SSH254WW-L, SSH254SH, SSH254WW, SSH254SH-L User Manual

SSH254 Series

Extra-Large size Stainless Steel Camera Housing

DESCRIPTION

:

The SSH254 series is designed to protect CCTV cameras in outdoor locations, especially where corrosive environment
can cause the premature deterioration of a standard aluminium/plastic camera housing, for this purpose the SSH254
series is constructed entirely from AISI316 stainless steel.

MODELS

:

SSH254 254 mm diameter x 600 mm length. Usable front window diameter 200 mm.
SSH254-L

254 mm diameter x 700 mm length. Usable front window diameter 200 mm.

SSH254SH

Same as SSH254, plus with sunshield and thermostatically controlled heater.

SSH254SH-L

Same as SSH254-L, plus with sunshield and thermostatically controlled heater.

SSH254WW

Same as SSH254SH, plus with wiper system. Usable front window diameter 200 mm.

SSH254WW-L

Same as SSH254SH-L, plus with wiper system. Usable front window diameter 200 mm.

SSH254IR70

254 mm diameter x 600 mm length with Germanium window 80x3mm (usable diam.

70mm), AR/DLC coating. Sunshield included. Heater optional.

SSH254IR70-L Same as SSH254IR70 but 700 mm tube length.
SSH254IR110

254 mm diameter x 600 mm length with Germanium window 120x3mm (usable

diam.110mm), AR/DLC coating. Sunshield included. Heater optional.

SSH254IR110-L Same as SSH254IR110 but 700 mm tube length.
SSH254IR155

254 mm diameter x 600 mm length with Germanium window 165x5mm (usable diam.

155mm), AR/DLC coating. Sunshield included. Heater optional.

SSH254IR155-L Same as SSH254IR155 but 700 mm tube length.
SSH254WWIR70

Same as SSH254IR70, plus wiper system.

SSH254WWIR70-L

Same as SSH254IR70-L, plus wiper system.

SSH254WWIR110

Same as SSH254IR110, plus wiper system.

SSH254WWIR110-L

Same as SSH254IR110-L, plus wiper system.

SSH254WWIR155

Same as SSH254IR155, plus wiper system.

SSH254WWIR155-L

Same as SSH254IR155-L, plus wiper system.

Issue 2 12/02/2009

Note: all models are available in 500 mm length, we are also ready to fulfil any particular request such as different
housing length or different glass diameter.

Tecnovideo Snc
Via San L. Murialdo, 8
36030 Villaverla (VI) ITALY
Tel. [phone]
Fax. [phone]
Web: www.tecnovideocctv.com

INSTALLATION

INSTALLING THE CAMERA

1) Extract the rear flange by removing the eight

screws. Be careful not to lose screws and
washer.

2) Prepare the housing to install the camera,
sliding the upper rail away from the lower rail.

3) Install the camera on the upper rail using one of
the ¼'' screws supplied, the plastic washer and
one or more spacers to be put under the
camera to adjust its height position.
Then slide the upper rail back on the lower rail
into the housing. Perform the electrical and
video connections. Cable glands are situated at
the bottom of the housing near the rear flange.
Eventually close the rear flange.

4) Use the four screws at the bottom of the
housing to fasten the housing to its apposite
support.

Issue 2 12/02/2009

Before performing any operation, turn off the power.
Only qualified personel can perform electrical operations
according to the regulations in force

Prior to installation and operation, read carefully this
manual of instructions

Upper
rail

Lower
rail

washe

r

screws

Cable glands

Screws