TecnoVideo 101W Series Installation Manual

101W Series

Compact Stainless Steel Camera Housing

with wall mounting bracket

Installation manual

Issue 20150804

DESCRIPTION

The 101W Series camera housing is constructed entirely from AISI316L stainless steel, for use in industrial and marine
environments and in general where a corrosive atmosphere can cause a rapid deterioration of a standard aluminium-steel
housing. Sunshield, thermostatically controlled heater and ceiling mounting bracket are included.

MODELS

101W Housing length=120mm
101W-L Housing length=200mm
101WIR50 Housing length=120mm with 50mm germanium window
101WIR50-L Housing length=200mm with 50mm germanium window
101WIR70 Housing length=120mm with 70mm germanium window
101WIR70-L Housing length=200mm with 70mm germanium window

CERTIFICATIONS

Weatherproof standard: IP67
EN 61000-6-3:2007 and 50130-4:1995 + A1:1998 + A2:2003 (EMC – Electromagnetic Compatibility)
60950-1:2006 + A11:2009 (LVD – Safety)

INSTALLING THE CAMERA

i

Prior to installation and operation, read carefully all instructions the in this manual and heed all warnings.

Unpack this equipment and handle it carefully. If the package appears to be damaged, notify the shipper immediately.

Use the original packaging to transport the unit. Disconnect power supply before moving it. In case of returning the
equipment, the original packaging must be used.

Make sure that the installation surface can support at least four times the weight of the unit in normal operating
conditions. In case of excessive external stress (e.g. vibration, strong winds or impact), the equipment may need additional
means of protection.

Proper stainless steel hardware should be carefully chosen to fasten the unit to the surfaces. Proper tools should be used
during the installation, in accordance to environmental requirements.

Use caution when lifting and assembling the unit. It is recommended that non-slip protective gloves be worn during
installation. The unit could bear sharp edges.

To maintain the IP rating of the unit, adequate cable glands must be used. The unit must be tightly closed when operating.

For security reasons, do not install the unit in the proximity of water containers and never push objects or pour liquids into
the unit. The unit can be safely used in damp environments or outdoors, as long as the connectors are properly sealed.

Video and data cables should not share the same conduit with supply voltage cables. Whenever EMC is an issue,
adequately shielded cables must be used.

Open only the covers pointed out in this installation manual. Other covers should be open only by the manufacturer.
Tightening/loosing the screws using automatic tools such as drill drivers may result in damaged threads.

This equipment has been designed to fit in harsh environments requiring little or no maintenance. Suggested inspection
interval is 6 months, but extremely harsh environments may require more frequent inspection and maintenance checks.
On each inspection check the O-ring seals. Replace if necessary.
Check cables, electrical connections and mounting hardware for integrity and tightness. Replace or tighten any
damaged/loose part.

Operating temperature: -20° +55° C (-4° +131° F).

h

Before performing any operation, turn off the power. The installation of the unit can be performed only by qualified
personnel in accordance with the regulations in force. Do not connect the unit to a supply circuit unless the installation is
completed.

Check carefully the supply voltage marked on the label. Incorrect Power Supply Voltage may damage the unit. Do not
overload the terminal connection, as it may cause a fire or electrical shock hazard.

An all-pole mains switch with an opening distance between the contacts at least 3 mm in each pole must be incorporated
in the electrical installation. The switch must be equipped with protection against the fault current towards the ground
(differential) and the overcurrent (magnetothermal, maximum 15A). It must be very quickly recognizable and readily
accessible. A suitable blow fuse must also be installed for protection.

For connection to the mains, use a multipolar cable having minimum 3x1,5 mm2 (15 AWG). The main cable must be at least
protected by an ordinary PVC sheath.

Fasten all the cables inside the housing with cables ties or other fixing means to avoid the electrical contact with
surrounding parts in case that terminal blocks screw off.

Electrical connections (such as plugs and cords) must be protected from potential hazardous environmental factors (e.g.
foot traffic, hitting objects).

Ensure that the unit case is properly earthed, connecting all the earth ground studs. Earth cable should be about 10mm
longer than the other cables on the connector, in such way that it won't be accidentally disconnected if the cable is
stretched or pulled.

When leaving the unit unused for long periods, disconnect supply cables.

2