Tecnologic K series, K38, K39, K49 Quick Programming Manual

Tecnologic ‘K’ Series

UK Quick Programming Guide – K38/39 & K49

This guide should be used alongside the full engineering manual, appropriate to the instrument being

used, where more detailed information can be found.

Programming the Instrument

Tecnologic controllers are supplied with default programmable settings that may be suitable for your
application. However we recommend that you go through the programming process, as incorrect
programming could compromise its performance.

Programming level pass numbers:

1381 – Basic menu without 10 second time out

1400 – Advanced menu without 10 second time out

** Minus 1000 to the pass number to add t ime out f un ct ion **

Note: To reset instrument to factory default settings, press P for 5 seconds and dial in -481.
Press P to confirm

Key

P button used for entering or moving to the next parameter.

Up & down buttons used for increasing or decreasing values.

U button is used for navigation between menus.
Holding down for 1 second will take you back one step.

Holding down for 2 seconds will take you out of configuration.

P

U





Unit 1 Farnborough Business Centre, Eelmoor Road, Farnborough, GU14 7XA

T: 01252 377600 F: 01252 377601 E: [e-mail]

Navigating the basic level programming guide

This is a blueprint guide for changing all the parameter settings on the instrument
within the 381 menu.

Note: Some parameters will disappear and/or additional parameters will appear depending on
settings selected. If the advanced menu is required use the 1400 pass code & select appropriate
menu using the ‘U’ key. Please refer to the main manual for more details.

Start/ Configure.

Power up unit. tEST will flash

Press & hold .
Dial in ‘1381’ & press P to
confirm.



With power to unit press P for 5

seconds.
‘Pass’ is displayed along with ‘0’

Use and arrow to
select required setting
within chosen parameter.
Press P to confirm.





Unit then accepts the chosen

setting and moves on to next
parameter in menu. (Repeat
above for all required parameters)

To exit programming press and

hold U to return to displayed
temperature.

To skip a parameter

press P to move onto
next one.

Unit will display first parameter in

menu, i.e. SEnS

381 Parameter menu

Display

Parameter name/

description

Manual

ref.

SEnS

Sensor/ input type

[2]

dP

Decimal point position

[3]

unit

Engineering Unit

[6]

o1F

Output function 1

[12]

o2F*

Output function 2

[15]

cont

Control type

[52]

Auto

Auto tuning for PID
parameters

[53]

Pb

Proportional band value
(°C)

[58]

int

Integral time (sec)

[59]

dEr

Derivative time (sec)

[60]

Fuoc

Fuzzy overshoot control

[61]

H.Act

Heating output actuator

[62]

SPLL

Min. adjustable set
point value

[73]

SPHL

Max. adjustable set
point value

[74]

SP1

Control set point

[75]

AL1t

Alarm 1 type/function

[24]

AL1L

Min. adjustable alarm 1
value

[26]

AL1H

Max. adjustable alarm 1
value

[27]

AL1

Alarm 1 set point value

[28]

HAL1

Alarm 1 hysteresis
(differential)

[29]

AL2t**

Alarm 2 type/function

[32]

t.F

Independent timer
function

[84]

Pr.F

Programmer function at
start-up

[89]

AdE***

Bargraph deviation

[118]

*Please note that o3F or/and o4F will only show dependent on model.
** If set AL2t, L, H etc will be repeated as with alarm 1

*** Parameter will not appear on all models.