Page 1
Keep these important operating instructions.
Check www.tecnare.com for updates.
Operation Manual
clip
+4dB
signal
TM
Optimised
9
6
Resolution
kHz
A B
INPUT
Store
uu
Recall
PRESET
CHANNEL
PARAMETER
DP-2696 Digital Loudspeaker Controller
A B
Limit
Limit
Limit
Limit
Limit
PARAMETER ADJUST
C
BA C
MUTE
-6dB
-6dB
-6dB
MUTE
-6dB
MUTE
3
4
MUTE
2
1
MUTE
Limit
-6dB
-6dB
MUTE
5
6
DP Series
Available
DP-2696
Digital Loudspeaker Controller
Page 2
Page 3
Digital Loudspeaker Controller
DP-2696 Operation Manual
IMPORTANT SAFE INSTRUCTIONS
Before using the device, be sure to carefully read the Safe Instructions. Keep this document with the device all time.
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
15 Use the mains plug to disconnect the device
from mains.
16 WARNING: To reduce the risk of fire of
electric shock, do not expose this device to
rain or moisture.
17 Do not expose this equipment to dripping or
splashing and ensure that no objects filled
with liquids, such as vases, are placed on
the equipment.
7 Do not block any ventilation openings. Install
in accordance with Exel Acoustic's
instructions.
8 Do not install near any heat sources such as
radiators, heat registers, stoves or other
apparatus (including amplifiers) that produce
heat.
9 Do not defeat the safety purpose of the
polarized or grounding type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug had two blades
and a third grounding prong. The wide blade
or the third prong are provided for your
safety. If the provided plug does not fit into
your outlet, consult an electrician for
replacement of the obsolete outlet.
10 Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles and the point where they exit
from the apparatus.
11 Only use attachments / accessories
specified by the manufacturer.
12 Use only with the cart, tripod, bracket or
table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart / apparatus
combination to avoid injury from tip-over.
18 The mains plug of the power supply cord
shall remain readily operable.
19 Do not connect the unit’s output to any other
voltage source, such as battery, mains
source, or power supply, regardless of
whether the unit is turned on or off.
20 Do not remove the top (or bottom) cover.
Removal of the cover will expose hazardous
voltages. There are no user s erviceable part
inside and removal may void warranty.
21 If the equipment is used in a manner not
specified by the Exel Acoustic, the protection
by the equipment may be impaired.
13 Unplug this apparatus during lightning
storms or when unused for long periods of
time.
14 Refer all servicing to qualified service
personnel. Service is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug
damaged, liquid has been spilled or objects
have fallen into the apparatus, this
apparatus has been exposed to rain or
moisture, does not operate normally, or has
been dropped.
DP Series | rev.
firm. 1.480 and above
2
Page 4
SYMBOLS USED
DP-4896 Operation Manual
Dangerous voltages; risk of
electrical shock
Pour indiquer les risques
resultant de tensions
dangereuses
Warnung vor gefährlicher
elektrischer Spannung
Presencia de voltajes
peligrosos
Important operating
instructions
Pour indequer important
Instructions
Wichtige Betriebsanweisung
oder Gebrauchsanleitung
sanleitung
Importantes instrucciones
operativas
Frame or chassis Protective earth ground
Masse, chassis Terre de protection
Rahmen oder Gehäuse Masse Schutzleiter
Masa o chasis Puesta a tierra
SAFETY WARNING
Permanent disconnection from the mains supply is to be achieved by removing the supplied
cord connector from the back of the unit.
Do not remove any covers, loosen any fixings or allow items to enter any aperture.
Objects filled with liquids should not be placed on this apparatus.
Replace the mains fuse only with a fuse of the same type
The rear of the product may get hot. Avoid direct skin contact during operation and for at least 5
minutes after power has been isolated.
AVERTISSEMENT DE SECURITE
Pour déconnecter l'appareil de l'alimentation principale de façon permanente, débranchez le
connecteur du câble fourni à l'arrière de l'appareil.
Ne retirez pas les couvercles, ne desserrez pas les fixations et ne laissez aucune pièce
s'introduire dans les ouvertures.
Ne placez pas d'objets contenant du liquide à proximité de l'appareil.
Ne remplacez le fusible de réseau principal que par un fusible du même type.
Le radiateur arrière de cet appareil devient chaud. Evitez tout contact direct avec la peau
pendant le fonctionnement et au moins 5 minutes après la mise hors tension de l'appareil.
3 DP Series | rev.
firm. 1.480 and above
Page 5
Digital Loudspeaker Controller
PRECAUCIONES DE SEGURIDAD
Para la desconexión permanente de la red eléctrica es necesaria la desconexión del cable
suministrado de la parte posterior de la unidad
No retire ninguna cubierta ni afloje tornillos. No permita que entre nada en el interior del
dispositivo.
No coloque sobre él objetos que contengan líquidos ni lo exponga a la lluvia o humedad.
Reemplazar el fusible principal sólo por un fusible del mismo tipo.
La parte posterior del dispositivo puede calentarse. Evite el contacto directo con la piel durante
el funcionamiento del dispositivo y durante, al menos, 5 minutos después de la desconexión
eléctrica.
DP-2696 Operation Manual
STANDARDS
FOR CUSTOMERS IN EUROPE
This product complies with both the LVD (electrical safety) 73/23/EEC and EMC
(electromagnetic compatibility) 89/336/EEC directives issues by the commission
of the European community.
Compliance with these directives implies conformity with the following European standards:
EN60065 Product safety
EN55103-1 EMC emissions
EN55103-2 EMC immunity
This product is intended for the following electromagnetic environments: E1, E2; E3 & E4.
FOR CUSTOMERS IN THE USA
This product has been tested for electrical safety and complies with:
UL60065 7th edition
FOR CUSTOMERS IN CANADA
This product has been tested for electrical safety and complies with:
CA /CSA C22.2 No.60065-03
DECLARATION OF CONFORMITY WITH CANADIAN ICES-003
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
FEDERAL COMMUNICATIONS COMMISSION NOTICE
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy, and if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try and
correct the interference by one or more of the following measures:
DP Series | rev.
firm. 1.480 and above
4
Page 6
DP-2696 Operation Manual
Reorient or relocate the receiving antenna.
Increase the distance between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
This equipment has been designed to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment.
5 DP Series | rev.
firm. 1.480 and above
Page 7
Digital Loudspeaker Controller
DP-2696 Operation Manual
DECLARACIÓN DE CONFORMIDAD
DECLARATION OF CONFORMITY
EXEL ACOUSTICS SL
CL Encinar, 282. Polígono Industrial Monte Boyal. 45950 –
Casarrubios del Monte (Toledo), España (Spain).
Declara que el producto DP-2696 y sus respectivas opciones,
cumple con la parte 15 de las reglas de la FCC.
Declare under our sole responsibility that devices in the DP-Series
range of products, comply with Part 15 of the FCC Rules.
La operación está sujeta a las siguientes dos condiciones
(1) Este dispositivo no puede causar interferencias perjudiciales y
(2) este dispositivo debe aceptar cualquier interferencia recibida,
incluidas las interferencias que puedan provocar un
funcionamiento no deseado.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
DP Series | rev.
firm. 1.480 and above
6
Page 8
DP-2696 Operation Manual
Table of Contents
IMPORTANT SAFE INSTRUCTIONS......................................................................................2
DECLARACIÓN DE CONFORMIDAD.....................................................................................6
1 Welcome.........................................................................................................................8
1.1 Thanks and unpacking .............................................................................................8
1.2 Unpacking................................................................................................................8
2 Quick reference guide...................................................................................................9
3 Introduction and key features...................................................................................12
3.1 Introducction .......................................................................................................... 12
3.2 Key Features..........................................................................................................13
4 The User Guide............................................................................................................14
4.1 Front panel.............................................................................................................14
4.2 Rear panel .............................................................................................................16
5 Operation......................................................................................................................17
5.1 Starting up the unit .................................................................................................17
5.2 Selecting a Factory Preset......................................................................................17
5.3 Creating a Crossover.............................................................................................. 18
5.4 Navigation and Viewing Parameters .......................................................................18
5.5 Presets...................................................................................................................19
6 DSP Processing Layout ..................................................................................................20
6.1 Stereo / Mono Formats ........................................................................................... 21
6.2 DSP Processing – Input Channels..........................................................................21
6.3 Output Channels ....................................................................................................23
6.4 Utilities ................................................................................................................... 26
7 Technical Specification ...............................................................................................27
8 EQ and Filter Response Graphs.................................................................................29
7 DP Series | rev.
firm. 1.480 and above
Page 9
Digital Loudspeaker Controller
DP-2696 Operation Manual
1 Welcome
1.1 Thanks and unpacking
Thank you for choosing a Tecnare® DP-2696 Digital Loudspeaker Controller for your
application. We are confident that you will be pleased with the performance, unique features,
configuration flexibility, reliability, and long-term durability offered by this product.
Please spare a little time to study the contents of this manual, so that you obtain the best
possible performance from this unit. Control and editing features are accessible via the front
panel interface or via the included Podware software.
All Tecnare® products are carefully engineered for world-class performance and reliability.
If you would like further information about this or any other Tecnare® product, please
contact us. We look forward to helping you in the near future.
Information and specifications are subject to change. Updates and supplementary
information are available on the Tecnare® website:
http://www.tecnare.com
Tecnare Technical Support is available at:
(T): +34 918 170 110 - +34 918 171 001
(e-mail): support@tecnare.com
Thank you again for placing your confidence in Tecnare® products.
1.2 Unpacking
After unpacking the unit please check carefully for any damage to the device or the supplied
accessories. Every Tecnare product is tested and inspected before leaving the factory and
should arrive in perfect condition. If damage is found, please notify the carrier concerned at
once. You, the consignee, must instigate any claim. Please retain all packaging in case of future
re-shipment.
DP Series | rev.
firm. 1.480 and above
8
Page 10
2 Quick reference guide
DP-2696 Operation Manual
Display
The LCD displays preset and parameter information. The default screen is shown after start up
and displays the number and name of the current preset on the lower line of text. When
navigating around the adjustable parameters, other information is shown.
Channel Select Buttons
The currently selected input or output channel is shown in the top left corner of the display.
Pressing the channel select buttons scrolls through the available inputs and outputs. If operating
stereo linked the channel pair is shown. For example ‘CH A+B’ means both input A and B
parameters.
Edit Select Buttons
The name of the edit parameter page is displayed in the bottom left portion of the LCD.
Pressing the edit select buttons moves through the available parameter pages for the current
input or output.
Parameter Knobs
Up to three parameters are shown on the display. The parameter name is shown with its’
current value below. Where appropriate, parameters are grouped according to function. For
example the parametric equalisation page shows centre frequency, width and gain. Turning a
parameter knob clockwise will increase the value of a parameter, turning anti-clockwise will
decrease it. Turning a knob rapidly will cause the action to ‘accelerate’, so the value changes
more rapidly.
Mute Buttons
The indicators next to the mute buttons indicate their current status. Pressing a mute button
toggles between the mute on and off.
Store Button
The unit has 45 preset locations. To store a preset in a location, press the store button and use
the parameter knobs to select the preset location and name the preset. Pressing the store
button again completes the task. Pressing any button other than store during the process
cancels the procedure.
Recall Button
To recall a preset, press the recall button and use parameter knob A to select the required
preset. Pressing the recall button again will activate the preset. You will then be asked to
confirm by pressing recall once more. As with the store function, pressing any button other will
cancel the process.
9 DP Series | rev.
firm. 1.480 and above
Page 11
Digital Loudspeaker Controller
DP-2696 Operation Manual
Limiter Settings
In order to offer the maximum of protection, some factory presets of the DP2696 can be entered
with the fixed limiting device with 0 dBu, limiting the power to approximately 30 W in 8. It is then
essential to set the threshold according to your devices.
To do it :
▪ with the front panel buttons
– Use "CH" button to go to the selected output
– Use the "Parameter" button to go to the Threshold parameter
– Adjust with the parameter knob.
▪ with dedicated software
- Go to panel control of DP2696 (Device then Add Device Panel, select
DP2696, press enter)
- Open selected "Output" window (1 to 6)
- Setting Threshold is located at the bottom right and can be adjusted
from - 40 to +20 dBu The following table expresses the threshold
corresponding to the nominal output power provided by the amplifier.
Values for a standard gain of 26 dB
Level in dBu Power under 8 Ω Power under 4 Ω
0 30W 60W
+1 38W 76W
+2 48W 96W
+3 60W 120W
+4 75W 150W
+5 95W 190W
+6 120W 240W
+7 150W 300W
+8 190W 380W
+9 240W 480W
+10 300W 600W
+11 380W 760W
+12 480W 960W
+13 600W 1200W
+14 760W 1520W
+15 960W 1920W
+16 1200W 2400W
+17 1520W 3040W
+18 1920W 3840W
Assignment of the input signals towards output signals
▪ with the front panel buttons
Limiter threshold : threshold (dBu) = 20 log (sqrt [Power (W ) x Impedance (Ω)]/0,775) amplifier gain (dBu). Also see Tecnare Technical paper.
- Use "CH" button to go to the selected output
- Use the Parameter button to go to the "source" function.
- Choose source with the first knob which offers possibility between the
Inp_A, Inp_B & Sum_A+B
DP Series | rev.
firm. 1.480 and above
10
Page 12
DP-2696 Operation Manual
▪ with dedicated software
- Go to panel control of DP2696 (Device then Add Device Panel, select
DP2696, press enter)
- Open Crossover window.
- Access to the choice of the source is in the first column of the table.
Connection to a computer
Connection RS232 Many laptops do not comprise a connection series RS232. It is then
advisable to use a converter USB towards RS232. We can provide an optional accessory USB
& RS232 interface or you can use a commercial interface. Unfortunately, few converters meet
the requirements to perform correctly with the DP2696. The converters must be equipped with
chips FTDI or Prolific X (imperative version "X"). The following converters USB - RS 232 were
tested and are satisfactory.
▪ Aten UC 232A (Is the one with the most updated drivers)
▪ Easysync US232B
▪ Easysync USB-COM
A 9 pins extension cable should be envisaged, in addition to the converter, because this device
cannot be installed directly on the DP2696. Podware software is available on request or can be
download on our Web site: www.tecnare.com.
11 DP Series | rev.
firm. 1.480 and above
Page 13
Digital Loudspeaker Controller
DP-2696 Operation Manual
3 Introduction and key features
The TECNARE DP2696 Digital Loudspeaker Controller represents current state-of-the-art
technology. Taking advantage of the latest advances in analogue to digital conversion and
digital signal processing technologies, these processors offer top-of-the-range professional
performances. Below is a list of key features, followed by some information on the major
advancements of the DP2696 feature set.
3.1 Introducction
Technical specification
▪ Combination of converters A/D and D/A made up with components of high range
produced by Burr Brown and Wolfson, selected carefully to offer an excellent sound
quality.
▪ DSP Processors of new generation Analogue Devices SHARC.
▪ Bandwidth extended of 10Hz to 40 Khz and sampling rate of 96 Khz, for a perfectly
linear frequency response.
▪ Keys and LCD screen allowing an adjustment of the parameters simple and
intuitive.
▪ PC software: Podware
▪ 2 input / 6 analogue output
▪ A/D & D/A Converters, 24 bits / 96 kHz
▪ 50 memories of configurations
▪ High sound quality
▪ TECNARE dedicated Presets
▪ Software control
▪ User friendly
Applications
▪ Management and treatments for system in multi diffusion TECNARE, with or without
subwoofer
▪ Digital delay
▪ Equalization for TECNARE loudspeakers
▪ Area management & signal distribution
DP Series | rev.
firm. 1.480 and above
12
Page 14
Specifications
▪ Bandwidth : 10 Hz - 40 kHz
▪ Dynamic >112 dB
▪ High pass Filter & low pass shelving,
▪ Bessel, Butterworth, Linkwitz Riley, Hardman crossover Filters
▪ 400 ms input Delay, 80ms output
▪ Limiting threshold by 0.2 dB step
▪ Parametric EQ 6 bands per input and output, 10 Hz with 25.4 Khz by step of 1/36
octave
▪ Possible locking of controls of the front panel
▪ Serial port standard
▪ Port Network optional
DP-2696 Operation Manual
3.2 Key Features
Minimal signal path design
Sonically superb ADC / DAC combination; a carefully matched pairing of the best
devices from Burr Brown and Wolfson
Newly released family of Analogue Devices SHARC DSP
Extended bandwidth; 96kHz sampling frequency provides for a nominally flat
response to 40kHz.
Parameter knob and LCD provide a rapid, user-friendly control interface
13 DP Series | rev.
firm. 1.480 and above
Page 15
Digital Loudspeaker Controller
DP-2696 Operation Manual
4 The User Guide
This user manual gives a progressively more detailed description of the functions of the
TECNARE DP2696 Digital Loudspeaker Controller. A single page quick reference guide is
provided for those users who are experienced with this type of equipment and just need to know
how to ‘drive’ the front panel.
A detailed explanation of the front and rear panel controls and indicators is contained in the
next section. The final section describes each individual function or feature with annotated
images explaining its’ use. Where appropriate, the LCD is shown to further elaborate on the
units’ operation.
To complete the manual a reference section is included, describing the technical
performance of the device complete with graphs of filter responses and details of the Factory
Presets and their configuration.
4.1 Front panel
The front panel of the DP2696 provides access to all of the powerful features of the Digital
Loudspeaker Controller system.
Figure 1: Front panel schema
Input Signal Indicators
A set of three pairs of LEDs indicate signal present, +4dBu and input clip for each
channel. The signal present LEDs operate at approximately –40 dBu, giving a useful indication
of even relatively low input signal levels. The +4 dBu LEDs are intended to show nominal
operating level and can also be useful for setting system gain structure. Clip LEDs warn the
user of input overload and operate at +19 dBu.
Preset Store and Recall
These controls provide access to the 45 presets stored within the device. Pressing the
store button allows the user to name a preset and choose which memory location it will be held
in. Pressing store button again completes the process. The Recall function operates in a similar
way, pressing the recall button allows the user to select which preset they require, pressing the
button for a second time, then confirming, recalls the new DSP settings.
Note that presets cannot be stored or recalled when Secure mode is activated.
DP Series | rev.
firm. 1.480 and above
14
Page 16
DP-2696 Operation Manual
Channel Select Buttons
The currently selected channel is displayed on the top left hand corner of the LCD.
Pressing the channel buttons scrolls through the available input and output channels and finally
through the utility functions and back to the default screen. If operating a stereo linked preset,
the channel name will indicate the channel pairing. For example ‘A+B’ means both input A and
B parameters. The name of the output will be shown briefly at the top of the display when
stepping onto an output.
Edit Select Buttons
The currently selected edit parameter page is displayed on the bottom left corner of the
LCD. Pressing the edit select buttons moves through the available parameters for the current
input or output.
Text Display
Preset, channel, parameter and status information is shown on the 2 x 24-character text
display. In most screens the currently selected channel is displayed on the upper line and the
edit parameter on the lower line. To simplify the display and enhance security, some
parameters or parameter pages are omitted when not relevant.
Parameter Knobs
Three velocity sensitive parameter knobs are used to adjust parameters shown on the
display. Up to three parameters at a time are displayed on the screen. The parameter name is
shown above the parameter value in each of the three screen sections. The parameter knobs
have a fixed association with the screen sections; the rightmost parameter knob adjusts the
rightmost parameter and so on.
Output Signal / Limiter Indication
Two LEDs are provided for each output channel. These show the signal level relative to
the limiter threshold. The yellow LED will light when the signal is 6dB below the threshold and
the red warning LED will light when the limiter threshold is reached.
Mute Buttons and Status LEDs
Each output has a mute button and associated mute status LED. Pressing the button
toggles the mute on and off.
Note that the mute buttons do not function when the Secure mode is activated.
15 DP Series | rev.
firm. 1.480 and above
Page 17
Digital Loudspeaker Controller
DP-2696 Operation Manual
4.2 Rear panel
The rear panel provides connections for two inputs and six outputs. An RS232 connector
allows connection to a remote computer running the “Podware” software. Optional PCC|Net cad
is available. PCC|Net must be plugged to the computer via USB, and the DP2696 linked to the
adapter with RJ45 cables(you can have several daisy-chained processors).
Figure 2: Rear panel schema
Power Inlet
The Tecnare DP2696 unit should be connected to a suitable mains electricity supply
using an earthed IEC C14 connection power lead. The processor has a switch mode power
supply that is capable of operating with a nominal mains voltage of 85V to 240V, 50/60Hz
without re-configuration.
NOTE: The DP2696 must be earthed to a suitable power earth; failure to do so may affect
performance and/or operation and will invalidate warranty and could be potentially hazardous.
Network Expansion Port
When fitted with a network option, the network connections will be here.
Communications Port Connector
Tecnare DP4896 processor may be controlled entirely from another controller, typically
a Personal Computer, running an application that is compliant with the ObCom standard.
Connection will normally be made to the controller via this serial port connector. This port is also
used for updating the firmware in the unit.
Note that the communications port is NOT disabled when the front panel is made secure using
the secure button.
DP Series | rev.
firm. 1.480 and above
16
Page 18
DP-2696 Operation Manual
Secure Button
A momentary button is fitted behind the rear panel, between the output XLRs and the
RS232 port. When activated, this will disable all the front panel controls so they cannot affect
the signal path, making the unit secure against tampering. When in secure mode, the indicators
still operate normally.
Note that the communications port is still active in secure mode.
Audio Output Connectors
The processed outputs are impedance balanced, and wired pin-1 ground, pin-2 hot and
pin-3 cold. An unbalanced input may be driven by connecting pin-3 ‘cold’ signal to the ground
connection of the unbalanced destination input. Note that output pin-1’s are ground lifted at
audio frequencies but connected to ground at RF for good EMC performance. The intention
being that the amplifiers the processor is driving should be responsible for the grounding of their
input cable shields.
Audio Input Connectors
All audio connections are fully balanced and wired pin-1 ground, pin-2 hot & pin-3 cold.
The two inputs have pin-1 connected directly to the chassis and feed the signal processing
chains. If an unbalanced source is used, a connection should be made between the pin-3 ‘cold’
signal and the ground connection of the unbalanced source.
5 Operation
Most of the functions and Systems setting in the Tecnare DP2696 are available via front
panel interface, navigating with the front panel buttons and knobs and viewed on the display.
The same functions are paralleled in the Podware control software. The user can choose to
control DP2696 from the front panel or remotely via Podware control software, as they are
interactive and communicate bi-directionally.
5.1 Starting up the unit
The unit will energise as soon as power is applied to the IEC inlet; there is no power
switch. During the start up process the firmware application model number and version numbers
are displayed and the outputs are muted until the unit has completed its internal checks. Once
the start-up routines are complete, the unit is ready to pass audio. The DSP signal path will be
restored to the same settings as when it was last powered down and the signal is gradually
ramped up to its correct level.
5.2 Selecting a Factory Preset
The DP4896 processors have a library of Factory Presets designed to suit a range of
applications. Factory Presets contain some parameters that are fixed and hidden from view; the
remainders of the DSP parameters are available for user manipulation. The number and type of
hidden parameters is dependant on the Factory Preset. To recall a Factory Preset for a
particular cabinet or system, press Recall and use the left hand parameter knob A to scroll
through the available Factory Preset locations (as indicated by a box symbol after the preset
number). Once the appropriate preset has been selected press recall again, at which point you
will be asked to confirm the action by pressing recall for a third time. This is to guard against
accidental recall of presets.
17 DP Series | rev.
firm. 1.480 and above
Page 19
Digital Loudspeaker Controller
Factory Presets are locked so they cannot be over-written. The user can, however,
store an edited version of a Factory Preset in any free preset location. Details of all the Factory
Presets including output designations can be found in Appendix A.
DP-2696 Operation Manual
5.3 Creating a Crossover
The Factory Presets are mono and stereo. These Base Presets are stored in locations 1
and 2 respectively. They can be used to develop settings for any loudspeaker. These presets
are locked but the user can name and store their own edited versions in any free preset
location.
5.4 Navigation and Viewing Parameters
In A Freq Width Gain
EQ1 100Hz 1.4Q 0.0dB
a
b
c
a b c
Figure 3: Crossover Menu
Many of the processing elements in each input and output path have features that may
be controlled by the user, such as gain, frequency or limiter threshold. We call these adjustable
features parameters.
A parameter may be adjusted when it is displayed by turning one of the three-parameter
knobs. Each of the three-parameter knobs is associated with a zone on the display. Adjusting
the leftmost parameter knob will change the value of the parameter showing in the leftmost
zone of the display and so on. Turn a knob clockwise to increase the value of a parameter, or
anti-clockwise to decrease it. The knobs are velocity-sensitive so turning a knob rapidly will
cause the action to ‘accelerate’, so the value changes more rapidly.
5.4.1 Navigation
The DSP parameters are organised by channel. The currently selected channel is
shown in the top left hand corner of the display. You can navigate between the channels by
pressing the channel buttons. Pressing the channel buttons will scroll through the channels,
utilities and back to the default screen. When using a Preset that is stereo linked, the channel
selection will reflect this. For example ‘1&4’ indicates outputs 1 and 4. When navigating onto an
output channel, the usage of the output, as defined in the Preset, will be shown briefly at the top
of the screen.
Pressing the edit navigation buttons gives access to the various pages of parameters
available for each channel. The currently selected page is shown in the bottom left hand corner
of the display. This is omitted on some pages where the function is obvious. The screen shows
up to three (normally related) parameters for a given part of the processing functions on a given
channel.
DP Series | rev.
firm. 1.480 and above
18
Page 20
DP-2696 Operation Manual
CHANNEL
Out1 Freq Width Gain
EDIT
EQ1 100Hz 1.4Q 0.0dB
a
b
c
Figure 4: Module sub-menu EQ
The edit buttons allow you to scroll, in either direction, through the different processing
pages for a given Channel. When you go past the last page, you will be returned to the default
page. The channel buttons allow you to scroll, in either direction, through the input and output
channels, whilst trying to maintain the currently viewed processing block. If the channel you
scroll to does not have the currently viewed processing block, the next one will be shown
instead.
NB. When the unit powers-up, the settings will be the same as those when the unit was last
switched off.
5.5 Presets
The device contains a total of forty-five user and Factory Presets. The user cannot
overwrite the basic mono or basic stereo Preset programs.
5.5.1 Preset Recall
To select an existing preset, press the Recall Button so the indicator above it
illuminates. Turn parameter knob A until the required preset number is shown on the display.
Factory Presets are indicated by a box symbol appearing after the preset number. Press the
Recall Button again to activate the Preset. Pressing any other button will cancel the operation.
Users can develop their own Preset based on one of the Factory Presets stored within
the device. Once a Preset has been recalled, a user has complete freedom to adjust any or all
of the parameters. Factory Presets can be used as the basis for user Presets but they have
some parameters that are predefined as a function of the loudspeaker system. These
parameters are "hidden" from the user, as they should be constant regardless of application.
RECALL RECALL
19 DP Series | rev.
Preset Name
Recall 32 My System
SELECT PRESET
TO RECALL
a
Figure 5: Menu Recall/ Preset Name
firm. 1.480 and above
a b
c
Page 21
Digital Loudspeaker Controller
5.5.2 Preset Store
DP-2696 Operation Manual
To store the current Preset in a user location, press the Preset Store Button so the
indicator above it illuminates. Turn the first parameter knob until the required Preset location
number is show on the display. A Preset name of up to 12 characters in length can be entered
using parameter knobs B and C. Pressing the Store Button again completes the process and
stores the Preset. As with Preset Recall, pressing any other button cancels the operation.
The user can overwrite non-protected Presets only; if an attempt is made to save a
Preset in a location already occupied by a Factory Preset a ‘LOCKED PRESET’ message is
displayed.
Preset Name
Store 32 My System
a b
SELECT STORE
STORE STORE
LOCATION
c
a
Figure 6: Menu Store/ Preset Name
6 DSP Processing Layout
NAME PRESET
cb
DP Series | rev.
firm. 1.480 and above
20
Page 22
DP-2696 Operation Manual
6.1 Stereo / Mono Formats
There is only one ‘standard’ layout of the processing blocks, but flexible routing and
control linking allows this layout to be adapted to a wide variety of applications.
There are two ‘Formats’, Mono or Stereo. With the Mono format, all outputs have unique
parameter settings, and all outputs are identical in terms of processing functions and routing
capability. This is the most flexible Format.
Stereo format pairs the inputs and outputs for stereo operation, the parameters of each
member of the pair being identical. The routing of inputs to outputs is fixed. This format is
intended for symmetrical stereo operation, eliminating the need to make identical parameter
adjustments for each channel.
The channel pairing is: Left and Right Inputs:
Outputs 1 (routed from L input) and 3 (routed from R input)
Outputs 2 (routed from L input) and 4 (routed from R input)
Outputs 3 (routed from L input) and 6 (routed from R input)
6.2 DSP Processing – Input Channels
Gain
In A Gain
0.0dB
a b
a
Knob A: Gain, adjustable in 0.2dB steps from –80 dB to +20dB
c
Delay
In A Delay
1.50ms
a b
a
Knob A: Delay, adjustable in variable steps from 0 to 400ms
The delay parameter is adjustable in fine steps at low values; the adjustment becomes
progressively coarser as the value increases. The velocity sensitive Parameter Knobs therefore
provide accurate setting of driver offset delays (typically below 10ms) and rapid setting of longer
system alignment delays.
c
21 DP Series | rev.
firm. 1.480 and above
Page 23
Digital Loudspeaker Controller
DP-2696 Operation Manual
High Pass Filter
In A Freq Shape
HPF 20.0Hz LR24
a b
a b
c
Knob A: Frequency, out (off), 20.0Hz to 25.6kHz in variable steps
Knob B: high pass filter type
System high pass filtering is provided for the input signal. This is the preferred location
for high pass filtering as it affects all outputs and can therefore improve inter-band phase
relationships. Filter type is selectable from Butterworth, Bessel, Linkwitz-Riley and Hardman.
Filter slopes of up to 4th order or 24dB / octave are provided. Not all filter types are available in
all slopes. For example 18dB / octave Linkwitz-Riley filters do not exist. The Hardman type filter
is always described by its’ order as the filter becomes progressively steeper rather than
following a linear slope so a dB/octave description is not accurate.
Parametric Equalisation
Eight sections of equalisation are provided, two shelving filters and six fully variable
parametric sections.
High and Low shelving filters
In A Freq Slope Gain
EQ1 100Hz 12dB 0.0dB
a
a b c
Knob A: Frequency, 10.0Hz to 25.6kHz in variable steps
Knob B: Slope, 6 to 12dB / octave in 1dB steps
Knob C: Gain, +/-15dB in 0.2dB steps
The frequency is specified as point where the filter deviates by 3dB from the gain value.
b
DP Series | rev.
c
firm. 1.480 and above
22
Page 24
Parametric Filter
Knob A, Centre Frequency, 10.0Hz to 25.6kHz in variable steps
Knob B, Width, display selectable, Q or BW (Bandwidth) Oct adjustable from 0.1 to 5
octaves in variable steps Q adjustable from 14.2 to 0.2 in variable steps
Knob C, Gain, +/-15dB in 0.2dB steps
DP-2696 Operation Manual
In A Freq Width Gain
EQ1 100Hz 1.4Q 0.0dB
a
b
a b c
c
6.3 Output Channels
Gain and Polarity
a b
Knob A: Gain, adjustable in 0.2dB steps from –80 dB to +20dB
Knob B: Polarity, selectable, normal or reversed with reference to other outputs
Delay
Out1 Gain Pol
0.0dB Rev
a b
c
Knob A: Adjustable in variable steps from 0 to 80ms
23 DP Series | rev.
Out1 Delay
1.50ms
a b
a
firm. 1.480 and above
c
Page 25
Digital Loudspeaker Controller
As for input delay, velocity sensitive Parameter Knobs provide finer adjustment at low levels and
rapid selection of higher values.
DP-2696 Operation Manual
High and Low Pass Filter
Out1 Freq Shape
LPF 2.50k LR24
a b
a b
Knob A: Frequency, <<out, 20.0Hz to 25.6kHz, out>>
Knob B: high pass filter type
c
Filter type is selectable from Butterworth, Bessel, Linkwitz-Riley and Hardman. Filter slopes of
up to 8th order or 48dB / octave are provided. Not all filter types are available in all slopes. For
example 18dB / octave Linkwitz-Riley filters do not exist. The Hardman type filter is always
described by its’ order as the filter becomes progressively steeper rather than following a linear
slope so a dB/octave description is not accurate.
Parametric Equalization
Eight sections of equalisation are provided in a similar format to the input channel equalisation;
two shelving filters and six parametric.
Out1 Freq Slope Gain
EQ>- 100Hz 12dB 0.0dB
a b
a cb
Knob A: Frequency, 10.0Hz to 25.6kHz in variable steps
c
Knob B: Slope, 6 to 12dB / octave in 1dB steps
Knob C: Gain, +/-15dB in 0.2dB stops
The frequency is specified as point where the filter deviates by 3dB from the gain value.
DP Series | rev.
firm. 1.480 and above
24
Page 26
Knob A, Centre Frequency, 10.0Hz to 25.6kHz in variable steps
Knob B, Width, display selectable, Q or BW (Bandwidth) BW adjustable from 0.1 to 5
octaves in variable steps Q adjustable from 14.2 to 0.2 in variable steps
Knob C, Gain, +/-15dB in 0.2dB steps
Limiters
DP-2696 Operation Manual
Out1 Freq Width Gain
EQ1 100Hz 1.4Q 0.0dB
a b
a b c
c
Out1 Thresh
LIM 4.0dB
a b
a
Knob A: Threshold, -40dBu to 20dBu in 0.2dB steps
A high performance, low distortion limiter is provided on each output. Threshold is user
adjustable; all other parameters are carefully calculated dependant on configuration to provide
clean and effective control of signal dynamics.
Routing
c
Out1 Source
Inp A
a b
c
a
Knob A: Output source, selectable; Input A, Input B or Sum A+B
Configures the routing from input to output. This function is only available in mono format
Presets.
25 DP Series | rev.
firm. 1.480 and above
Page 27
Digital Loudspeaker Controller
DP-2696 Operation Manual
6.4 Utilities
Three utility functions are provided to adjust screen contrast, the display units used for
parametric equalisation bandwidth and switch between stereo and mono mode.
The device automatically adjusts for the variations in display contrast as the
temperature of the LCD changes. The screen contrast utility control sets the base contrast of
the screen and also allows optimization for a given viewing angle.
Parametric equalisation width parameters can be displayed in either ‘Q’ or bandwidth,
expressed in octaves.
Util Screen ParaEQ
1.. 100% BW=Q
a b
Care should be taken when swapping between mono and stereo mode as the
parameter set for the left hand channels will be copied to the right hand side, overwriting those
settings. This is not reversible and could represent quite a significant and potentially damaging
change to the processing.
c
Util Mode
..2 Mono
a b
c
DP Series | rev.
firm. 1.480 and above
26
Page 28
7 Technical Specification
General
▪ Input 2
▪ Output 6
▪ Input impedance >10k balanced
▪ Output Imp <100 imp. Balanced
▪ Max Input level +20dBu
▪ Max Output level +22dBu into 600 load
▪ Sample rate 96kHz
▪ Bit Depht 24 bits
▪ Frequency Response: 10Hz - 40kHz, +/- 3dB (filters disabled)
20Hz to 20 kHz, +/-0,5dB (filters disabled)
▪ Dynamic Range >112 dB (A weighted, 22kHz bandwidth)
>109 dB (un-weighted, 22kHz bandwidth)
▪ THD . <0,01 % (+10 dBu, 20 Hz to 20 kHz, 30 kHz bandwidth).
▪ Serial Comms Data 38.4kbaud, format: 8 data, 1 stop, no parity
Processing
▪ Gain +20 dB to -80 dB and mute, 0,2 dB steps
▪ Output Ch. Source Input A, Input B and SUM
▪ HP filter frequency Off, 10 Hz to 25,4 kHz, 1/36 d"octave steps
▪ LP filter frequency 10 Hz to 25,4 kHz and Off, 1/36 d"octave steps
▪ LP / HP filter type 12, 18 and 24 dB/octave Bessel and Butterworth 12, 24 and 48
dB/octave Linkwitz Riley 4th or 8th order Hardman
▪ Delay Input 400ms, output 80ms
▪ Limiter High performance limiter adjustable threshold in 0.2dB steps automatic time
constants
▪ EQ Frequency 10Hz to 25kHz, 1/36 octave steps
▪ EQ Gain +15dB to -15dB, 0.2dB steps
▪ EQ Width 5.0 to 0.1 octaves bandwidth, 1/36 octave steps
Connectors
▪ Audio input 3 pin female XLR
▪ Audio output 3 pin male XLR
▪ Serial Comms
▪ Optional PCC|Net Network comm
▪ Mains 3 pin IEC
Environmental
▪ Temperature 0 to +45C
▪ Humidity 0 to 80% RH (non-condensing)
▪ Mains Power Universal switch-mode PSU, 85v to 250v AC, 50/60 Hz
▪ Consumption <25Watta
Dimensions
▪ Height 1U (44mm)
▪ Width 482mm
▪ Depth 254mm
▪ Weight 2.7kg net
DP-2696 Operation Manual
27 DP Series | rev.
firm. 1.480 and above
Page 29
Digital Loudspeaker Controller
Options
▪ PCC|Net USB & RS232 Interface
▪ PCC|Net Power Supply
▪ ETHERNET Interface
▪ Accesory Racking Kit
▪ Dante® Bridge .
DP-2696 Operation Manual
DP Series | rev.
firm. 1.480 and above
28
Page 30
8 EQ and Filter Response Graphs
DP-2696 Operation Manual
6
0
6
12
18
Magnitude, dB
24
30
36
100 110
6dB/Oct
12dB/Oct
18dB/Oct
24dB/Oct
48dB/Oct
6
Butterworth
3
Frequency, Hz
Linkwitz-Riley
110
4
0
6
12
18
Magnitude, dB
24
30
36
100 110
Frequency, Hz
3
110
4
12dB/Oct
24dB/Oct
48dB/Oct
29 DP Series | rev.
firm. 1.480 and above
Page 31
Digital Loudspeaker Controller
DP-2696 Operation Manual
6
0
6
12
18
Magnitude, dB
24
30
36
100 110
12dB/Oct
24dB/Oct
Bessel
3
Frequency, Hz
110
4
6
0
6
12
18
Magnitude, dB
24
30
36
100 110
Frequency, Hz
3
110
4
4th Order
8th Order
Hardman
DP Series | rev.
firm. 1.480 and above
30
Page 32
DP-2696 Operation Manual
15
10
5
0
5
Magnitude, dB
10
15
100 110
Frequency, Hz
3
110
4
Low shelf, varying Gain
High shelf, varying Slope
Shelving EQ
15
Parametric EQ
10
5
0
5
Magnitude, dB
10
15
100 110
Frequency, Hz
3
110
4
Varying Gain
Varying Bandwidth
31 DP Series | rev.
firm. 1.480 and above
Page 33
DP2696 RECALL SHEET
PRESET#: Mode: STEREO MONO Author: Date:
INPUT L
Gain: Phase: Delay:
HPF Freq: Shape:
>- Freq: Slope: Gain:
EQ1 Frec: Width: Gain:
EQ2 Frec: Width: Gain:
EQ3 Frec: Width: Gain:
EQ4 Frec: Width: Gain:
EQ5 Frec: Width: Gain:
EQ6 Frec: Width: Gain:
-< Freq: Slope: Gain:
OUTPUT 1
Gain: Phase: Delay:
HPF Freq: Shape:
>- Freq: Slope: Gain:
EQ1 Frec: Width: Gain:
EQ2 Frec: Width: Gain:
EQ3 Frec: Width: Gain:
EQ4 Frec: Width: Gain:
EQ5 Frec: Width: Gain:
EQ6 Frec: Width: Gain:
-< Freq: Slope: Gain:
OUTPUT 2
Gain: Phase: Delay:
HPF Freq: Shape:
>- Freq: Slope: Gain:
EQ1 Frec: Width: Gain:
EQ2 Frec: Width: Gain:
EQ3 Frec: Width: Gain:
EQ4 Frec: Width: Gain:
EQ5 Frec: Width: Gain:
EQ6 Frec: Width: Gain:
-< Freq: Slope: Gain:
OUTPUT 3
Gain: Phase: Delay:
HPF Freq: Shape:
>- Freq: Slope: Gain:
EQ1 Frec: Width: Gain:
EQ2 Frec: Width: Gain:
EQ3 Frec: Width: Gain:
EQ4 Frec: Width: Gain:
EQ5 Frec: Width: Gain:
EQ6 Frec: Width: Gain:
-< Freq: Slope: Gain:
INPUT R
Gain: Phase: Delay:
HPF Freq: Shape:
>- Freq: Slope: Gain:
EQ1 Frec: Width: Gain:
EQ2 Frec: Width: Gain:
EQ3 Frec: Width: Gain:
EQ4 Frec: Width: Gain:
EQ5 Frec: Width: Gain:
EQ6 Frec: Width: Gain:
-< Freq: Slope: Gain:
OUTPUT 4
Gain: Phase: Delay:
HPF Freq: Shape:
>- Freq: Slope: Gain:
EQ1 Frec: Width: Gain:
EQ2 Frec: Width: Gain:
EQ3 Frec: Width: Gain:
EQ4 Frec: Width: Gain:
EQ5 Frec: Width: Gain:
EQ6 Frec: Width: Gain:
-< Freq: Slope: Gain:
OUTPUT 5
Gain: Phase: Delay:
HPF Freq: Shape:
>- Freq: Slope: Gain:
EQ1 Frec: Width: Gain:
EQ2 Frec: Width: Gain:
EQ3 Frec: Width: Gain:
EQ4 Frec: Width: Gain:
EQ5 Frec: Width: Gain:
EQ6 Frec: Width: Gain:
-< Freq: Slope: Gain:
OUTPUT 6
Gain: Phase: Delay:
HPF Freq: Shape:
>- Freq: Slope: Gain:
EQ1 Frec: Width: Gain:
EQ2 Frec: Width: Gain:
EQ3 Frec: Width: Gain:
EQ4 Frec: Width: Gain:
EQ5 Frec: Width: Gain:
EQ6 Frec: Width: Gain:
-< Freq: Slope: Gain:
Page 34
DP-2696 Operation Manual
©2015
Tecnare Sound Systems. All rights reserved.
DP4896 Operation manual
The contents of this manual are furnished f or informational purposes only, are subject to change without notice, and
should not be construed as a commitment by Exel Acoustic SL. Exel Acoustic assumes no responsibility or liability for
any errors or inaccuracies that may appear in this manual. Except as permitted by applicable copyright law, no part of
this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic,
mechanical, recording or otherwise, without prior written permission from Exel Acoustic. Tecnare and PCC-Net are
trademarks of Exel Acoustic SL. Podware, BvNet, Dante and all third-party trademarks mentioned herein are the
property of their respective trademark holders.
Printed in Spain.
33 DP Series | rev.
firm. 1.480 and above
Page 35
EXEL ACOUSTICS SL
CL Encinar, 282 - Pol. Ind. Monte Boyal
45950 Casarrubios del Monte (To)
Spain
support@tecnare.com
www.tecnare.com - www.facebok.com/tecnare
(T): +34 918 170 110 - +34 918 171 001
(F): +34 918 183 053
rev. 1.2 2015
Loading...