Page 1
TeckNet M011 2.4GHz Cordless Mouse
Note:
German and French language user manuals can be downloaded
from our website: www.tecknet.co.uk.
Page 2
Welcome
Thank you for purchasing thisTeckNet product. To ensure optimum
performance and safety, please read these instructions carefully before
operating the product. It is strongly recommended you keep this manual for
future reference.
Technical Specifications
Button Count: 4 buttons
Operating Frequency: 2.4GHz
Resolution: 1000/2000DPI
Receiver interface: USB version 2.0
Operating Voltage: 3V
Operating Current: 10mA
Distance: up to 10m
Package Contents
1 x M011 Cordless Mouse
1 x USB Nano Receiver
1 x User Manual
1 x Warranty Card
Product Layout
1.Left Click Button
2.Right Click Button
3.Scroll Wheel
4.DPI Switch Button
01
Page 3
System Requirements
Hardware
• PC with a Pentium processor or equivalent AMD processors
• USB 2.0
Operating System
• Windows 2000, 2003, XP, Vista, Win7, Win8, Win8.1 ,Win10
Note: The scroll wheel only works under the operating systems listed above.
If you use the mouse under a different operating system, the mouse may
either not work or lose its enhanced features.
Product Introduction
Battery Installation
The M011 optical mouse uses two AAA batteries (not included).
18-Month Battery Life
The mouse consumes very little power and enables a long battery life of up
to 18 months without changing the battery. However please note that the
actual battery life may vary based on user and computing conditions.
1.Install the batteries into the compartment, and make sure the polarity of the
batteries is correct.The positive (+) and negative (-) ends of each battery
must match the positive (+) and negative (-) markings in the battery
housing. The red power indicator LED will flash.
2.Replace the battery. Open the battery compartment cover,tap the mouse
slightly and the batteries will drop out, ready to load new batteries, make
sure they correspond with the polarity markings.
AAA
AAA
2
1
02
Page 4
Receiver Connection
Remove the USB Nano receiver and plug it into a free USB port in your
computer. The Plug & Play function of your system will detect a new device
has been connected and install it automatically.
Intelligent Power Saving (IPS)
The mouse is equipped with Intelligent Power Saving (IPS) function.
• When the USB Nano receiver is disconnected or the PC is switched off, the
mouse will automatically switch off to conserve power.
• If the mouse is not operated for 10 minutes, it will automatically drop to sleep
mode. To wake the mouse, click any button.
Note: The receiver can be removed and storedin the battery compartment
while not in use.
USB Port Nano receiver
2
1
Take out the receiver Store the receiver
03
Page 5
DPI Switch
The mouse supports 2000 DPI, 1000 DPI. Press the DPI
button to switch to either setting.The default setting is
1000 DPI.Click the DPI button on the top of the mouse
once to switch from 1000 DPI to 2000 DPI.Click the DPI
button again to switch from2000 DPI back to 1000 DPI.
Reconnection
There is a wireless signal connection code for this mouse. High
temperatures, electro-magnetic fields or vibration may influence the code
signal and occasionally the mouse may need to be reconnected. Both the
mouse and Nano receiver have a built-in code and one mouse can be
connected to one receiver, or several mice to one Nano receiver.
Attention
1.Unplug the Nano receiver from USB port, and plug it back inagain.
2.Move the mouse within 50cm of the Nanoreceiver, re-install the battery or
press any key to reconnect; the above process must be completed within
15 seconds.
3.The mouse will be ready for use after reconnection.
1.To maximize battery life, it is recommended to use the mouse on a white
or light color surface.As the mouse might not work smoothly on some
special surfaces, such as smooth, dark or black, reflecting or 3D mouse
pad surfaces.
2.If not operated for 10 minutes, the mouse will enter auto-sleep mode.
Press any key or scroll wheel to activate the mouse again.
3.Do not use the mouse on a glass or mirrored surface, as these surface
will cause the mouse temporarily fail to work.
4.Avoid using the mouse on a metal surface, such as iron, aluminum or
copperwhich will shield the radio frequency transmission, slow down the
mouse presenter’s response time or causetemporarily fail to work.
5.If your PC has a metal case that containsaluminum or magnesium, use
the mouse by the side of the PC. The display panel may interfere with the
radio frequency if you use the mouse directly in front of the PC.
04
Page 6
FAQ
1.What should I do if the mouse does not work?
• Make sure that the polarity of the batteries is correct. The positive (+) and
negative (-) ends of each battery must match the positive (+) and
negative (-) markings in the battery housing.
• Make sure the batteries are not discharged.Try to remove the batteries,
and reinstall them again.
• Verify that your computer's power management features are turned off.
• Check the Nano receiver's USB connector is firmly attached to the USB
port of your computer.
• Still not working? Please try“Reconnection”.
2.The USB Nano receiver is recognized by Windows (XP, Vista, Win 7,
2000, 2003, 2007, Win8) but the cursor does not move?
• Check whether the low power indicator on the top of the mouse lights up.
If the sensor lights up, it is likely that the batteries are discharged. Please
replace the batteries.
• If replacing the batteries does not help, it is likely that the mouse is not
connected to the receiver.Please try“Reconnection”.
3.When I use the mouse, other 2.4G Cordless devices work more slowly or
fail temporarily – what should I do?
• The mouse has 34 channels to prevent interference. However the mouse
may cause interference with any cordless, radio-based device that
operates at 2402MHz - 2480MHz. To reduceinterference, move the
mouse’s receiver and the base unit of the affected deviceas far away
from each other as possible; alternatively try to change the 2.4G
frequency of the affected devices.
4.What should I do if the mouse responses slow or intermittently stops
working?
• Ensure that the mouse is within the operational working distance (1.5m)
from the USB Nano receiver and restart your PC.
• Increase the distance between the Nano receiver and the base units of
other cordless devices.
• Turn off any cordless device and their base units that are near the mouse
Nano receiver.
05
Page 7
Warning
Please read all instructions and warnings prior to using this product for the
first time. Failure to read and follow these safety and usage instructions
could result in fire, explosion, electric shock or other hazard that could
potentially cause property damage or even fatal injury.
• If you are using the mouse on a metal surface, move the mouse and the
receiver to a non-metallic surface. Metals, such as iron, aluminum or copper,
shield the radio frequency transmission and may slow down the mouse
presenter’s response time or cause the mouse to fail temporarily.
1.Keep the mouse and batteries out of the reach of children.
2.Replace old or weak batteries promptly.
3.Remove the batteries if the mouse is not going to be used for a long period
of time.
4.Don not disassemble, adjust or repair the mouse which may result in
exposure or safety hazards.
Disclaimer
Every effort has been made to ensure that the information and procedures in
this guide are accurate and complete, no liability can be accepted for any
errors or omissions and we reserve the right to make any changes without
further notice to any products mentioned herein.
Warranty
We warrant that product from authorized distributors will meet the applicable
product specifications and be free from all defects in design, assembly,
material and workmanship. Please contact TeckNet retailers, or visit our
website for more information about the product.
06
Loading...