Techpro IP-EL Series User Manual

IP-EL Series - User's Manual

PTZ

Control

Motion
Activated
Recording

Guaranteed

Warranty

View From

Anywhere

4K

Resolution

Welcome

Thank you for purchasing our IP camera!

This user’s manual is designed to be a reference tool for your system.

Please read the following safeguard and warnings carefully before you use this series product! Please keep

this user’s manual well for future reference!

Important!

DO NOT Connect all the cameras on the same network at the same time.
This will cause IP conflict within your network and you will not be able to
accress your cameras. Before connecting all the of the IP cameras on the
network One-At-A-Time.

DO NOT power the camera with both PoE and a power supply at the
same time.
If you purchase a PoE(Power Over Ethernet) device from us, Whether
as an External POE Switch or built into on of our NVRs, your camera
will be powered through the Ethernet cable and will not need to power it
with a seperate power supply.

*Restrictions may apply*

Our units do not support PAL

To find your cameras on the network, use the "config Tool" found in the
CD(under Software>ConfigTool) that came with your package. Some
cameras will be assigned as a DHCP. Therehore, The "IP Config Tool is
required to find the camera on the network.

Important Safeguards and Warnings

1．Electrical safety

All installation and operation here should conform to your local electrical safety codes.

The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited

power source is rated 12V DC in the IEC60950-1.This series product supports PoE too. Please note:

Do not connect these two power supplying sources to the device at the same time; it may result

in device damage!

We assume no liability or responsibility for all the fires or electrical shock caused by improper handling

or installation.

We are not liable for any problems caused by unauthorized modification or attempted repair.

2．Transportation security

Heavy stress, violent vibration or water splash are not allowed during transportation, storage and

installation.

3．Installation

Do not apply power to the camera before completing installation.

Please install the proper power cut-off device during the installation connection.

Always follow the instruction guide the manufacturer recommended.

4．Qualified engineers needed

All the examination and repair work should be done by the qualified service engineers.

We are not liable for any problems caused by unauthorized modifications or attempted repair.

5．Environment

This series IP camera should be installed in a cool, dry place away from direct sunlight, inflammable,

explosive substances and etc.

Please keep it away from the electromagnetic radiation object and environment.

Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.

Otherwise it may result in CCD (CMOS) optical component damage.

Please keep the sound ventilation.

Do not allow the water and other liquid falling into the camera.

Thunder-proof device is recommended to be adopted to better prevent thunder.

The grounding studs of the product are recommended to be grounded to further enhance the reliability

of the camera.

6. Daily Maintenance

Please shut down the device and then unplug the power cable before you begin daily maintenance

work.

Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens

surface.

Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to

dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the

device.

Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.

7. Accessories

Be sure to use all the accessories recommended by manufacturer.

Before installation, please open the package and check all the components are included.

Contact your local retailer ASAP if something is broken in your package.

Accessory Name Amount

IP Camera Unit

1

CD

1

Installation Accessories Bag

1

Table of Contents

1 General Introduction ..................................................................................................................

1.1 Overview........................................................................................................................

1.2 Features........................................................................................................................

.

2 Structure ......................................................................................................................................

2.1 Multiple-function Combination Cable ........................................................................

2.2 Framework and Dimension.........................................................................................

4 Quick Configuration Tool...........................................................................................................

4.1 Overview.........................................................................................................................

4.2 Operation.......................................................................................................................

5 FAQ .............................................................................................................................................

Appendix Toxic or Hazardous Materials or Elements ...............................................................

.

1.3 Camera Installation.......................................................................................................

1.4 Varifocal lens...................................................................................................................

1 General Introduction

1.1 Overview

This series IP camera integrates the traditional camera and network video technology. It adopts video

data collection, transmission together. It can connect to the network directly without any auxiliary

device.

This series IPC uses standard H.264 video compression technology, which maximally guarantees the

video quality.

It supports the IR night vision function. In the night environments, the device can use the IR light to

highlight the object which is suitable for the surveillance function in the low illumination environments.

The waterproof design conforms to the IP 66 level. It has the sound waterproof function suitable for

use in the outdoor environments.

It can be used alone or used in a network area. When it is used lonely, you can connect it to the

network and then use a network client-end. Due to its multiple functions and various uses, this

series IPC is widely used in many environments such as an office, bank, road

monitor and etc.

1.2 Features

User

Management

z Different user rights for each group, one user belongs to one group.
z The user right shall not exceed the group right.

Storage

Function

z Support central server backup function in accordance with your configuration

and setup in alarm or schedule setting

z Support record via Web and the recorded file are storage in the client-end

PC.

z Support network storage function such as FTP.

Network

Monitor

z IPC supports one-channel video data transmit to network terminal and then

decode. Delaying time is within 270ms (network bandwidth support needed)

z Max supports 20 connections.
z Adopt the following video transmission protocol: HTTP, TCP, UDP,

MULTICAST, RTP/RTCP, RTSP and etc.

z Support web access.

Network

Management

z Realize IPC configuration and management via Ethernet.
z Support device management via web or client-end.

Power

z External power adapter DC 12V.
z Support PoE.

Warning！
Do not connect these two power supplying sources to the device at the
same time; it may result in device damage!

Assistant

Function

z Log function
z Support system resource information and running status real-time display.
z Day/Night mode auto switch.
z Support picture parameter setup such as electronic shutter and gain setup.
z Support motion detect.
z Backlight compensation: screen auto split to realize backlight compensation

to adjust the bright.

z Support video watermark function to avoid vicious video modification.
z Built-in IR light. Support IR night vision.
z The enclosure conforms to the IP 66 protection. Has the waterproof function.

Step 1

If included please take the installation position map from the accessories bag,
and then paste it on the ceiling or the wall according to your monitoring area
requirements. Draw and then drill holes in the installation surface and then insert
expansion(anchor) bolts in the holes. Secure these bolts firmly.

Step 2

Turn counter clockwise to remove the decoration ring(plastic housing), turn the
pan base to the pedestal to loosen or secure firmly(metal housing) or Use the

inner hex wrench to remove the three enclosure fastening screws and then
remove the dome enclosure(glass enclousure). Adjust the pedestal position
according to the cable exit move(ceiling/side). Pull the cable through the cable
side exit at the installation surface and the pedestal.
(Please skip this step if you are mounting on a ceiling). Line up the screw holes
at the bottom of the pedestal to the expansion bolts in the installation surface.
Put three self-tapping screws to expansion bolts and then secure firmly. Now the
pedestal is on installation surface.

Ceiling or Wall

Expansion Bolt

Dome Camera Body

ST3 Self-tapping Screws

Decoration Ring

Plastic Housing

Dome Installation

1.3 Camera Installation