TechPlay ODCR2110 WD Instructions Manual

ODCR2110 WD

TURNTABLE WITH CD/MP3 PLAYER, DOUBLE CASSETTE DECK,

RADIO, BLUETOOTH & CD/USB/SD RECORDER

INSTRUCTION MANUAL

READ THIS INSTRUCTION MANUAL CAREFULLY BEFORE USE

PRODUCT FEATURES

- 33/45/78 RPM SELECTABLE TURNTABLE

- AUTOMATIC / MANUAL STOP TURNTABLE

- BELT DRIVEN SYSTEM

- BLUETOOTH WIRELESS MUSIC STREAMING WITH NFC

- PROGRAMMABLE CD/MP3 PLAYER

- DOUBLE CASSETTE DECK

- DIRECT USB/SD RECORDING FOR CD, TURNTABLE, CASSETTE, FM RADIO & AUX IN

- DIRECT CD RECORDING FOR CD, TURNTABLE, CASSETTE, AUX IN, USB/SD

- AUX IN FOR CONNECTION OF OTHER DEVICE (E.G. CD & MP3 PLAYER)

- USB/SD SLOT & CD PLAYER FOR MP3 PLAYBACK

- PLL RADIO WITH AUTO-SCANNING & PRESET STATIONS

- CLOCK ALARM / TIMER / SLEEP FUNCTION

- RCA LINE-OUT

- 45RPM ADAPTOR & REMOTE CONTROL

LOCATION OF CONTROL

A) 45 RPM ADAPTOR

B) LIFT LEVER (FOR RECORD PLAY / PAUSE)

C) AUTO STOP ON/OFF BUTTON

D) 33/45/78 RPM SPEED SELECTOR

E) TONE ARM

1) TUNER / BAND

2) SLEEP / TIMER

3) FUNCT

4) REC / DEL

5) MODE / CLOCK

6) CD 1 - PLAY/PAUSE BUTTON & TUNER SCAN

7) CD 1 - SKIP DOWN BUTTON

8) CD 1 - SKIP UP BUTTON

9) ALBUM / PRESET DOWN

10) ALBUM / PRESET UP

11) CASSETTE DECK A – RECORD

12) CASSETTE DECK A – PLAY

13) CASSETTE DECK A – FAST REWIND

14) CASSETTE DECK A – FAST FORWARD

15) CASSETTE DECK A – STOP / EJECT

16) CASSETTE DECK A – PAUSE

17) CASSETTE DECK B – PLAY

18) CASSETTE DECK B – FAST REWIND

19) CASSETTE DECK B – FAST FORWARD

20) CASSETTE DECK B – STOP / EJECT

21) CASSETTE DECK B – PAUSE

22) CD 2 - INCREMENT

23) CD 2 - SPLIT

24) CD 2 - FINALIZE

25) CD 2 - PLAY/PAUSE BUTTON

26) CD 2 - STOP BUTTON

27) CD 2 - SKIP DOWN BUTTON

28) CD 2 - SKIP UP BUTTON

29) CD 2 - RECORD

30) CD 2 - ERASE

31) CD 2 – ENABLE

32) REMOTE CONTROL RECEIVER

33) STANDBY INDICATOR

34) DUST COVER

35) POWER / VOLUME KNOB

36) CASSETTE DECK A DOOR

37) CD 1 – OPEN / CLOSE BUTTON

38) CD 1 – CD DOOR

39) EARPHONE JACK

40) USB SLOT

41) SD SLOT

42) AUX IN JACK

43) CD 2 – CD DOOR

44) CD 2 - OPEN / CLOSE BUTTON

45) CASSETTE DECK B DOOR

46) LINE-OUT RCA JACK

47) EXTNERAL POWER ADAPTOR JACK

48) SPEAKER BOX CONNECTION RCA JACK

49) FM WIRE ANTENNA

CAUTION:

- USAGE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE

SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

- THIS UNIT SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT QUALIFIED SERVICE

PERSONNEL.

- IF YOU FIND ANY MALFUNCTION OR FREZZING OF THE UNIT DURING OPERATION, PLEASE TRY TO

UNPLUG THE UNIT AND WAIT FOR 10 SECONDS. THEN PLUG THE UNIT AND RESTART AGAIN

WARNING:

- THE APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING AND THAT NO OBJECTS

FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS.

- BATTERIES (BATTERY PACK OR BATTERIES INSTALLED) SHALL NOT BE EXPOSED TO EXCESSIVE HEAT

SUCH AS SUNSHINE, FIRE OR THE LIKE.

PRECAUTIONS FOR USE

INSTALLATION

• UNPACK ALL PARTS AND REMOVE PROTECTIVE MATERIAL.

• DO NOT CONNECT THE UNIT TO THE MAINS BEFORE CHECKING THE MAINS VOLTAGE AND BEFORE

ALL OTHER CONNECTIONS HAVE BEEN MADE.

• DO NOT COVER ANY VENTS AND MAKE SURE THAT THERE IS A SPACE OF SEVERAL CENTIMETERS

AROUND THE UNIT FOR VENTILATION.

CONNECTION

1. CONNECT SPEAKER BOX WITH SPEAKER BOX RCA JACK

2. PLUG THE EXTERNAL POWER ADAPTOR WITH THE EXTERNAL POWER ADAPTOR JACK.

3. PUSH THE POWER KNOB TO SWITCH ON THE UNIT, STANDBY INDICATOR WILL BE OFF.

SETTING THE CLOCK

1 WHEN THE STANDBY INDICATOR LIGHTS UP, THE UNIT IS IN THE STANDBY MODE.

2 DURING STANDBY MODE, SELECT BETWEEN 12H OR 24H CLOCK OPTIONS:

3 PRESS AND HOLD MODE BUTTON FOR 3-5 SECONDS; 12H / 24H WILL BE FLASHING.

PRESS CD 1 - SKIP DOWN BUTTON OR CD 1 - SKIP UP BUTTON TO SELECT 12H / 24H MODE.

PRESS MODE BUTTON AGAIN TO CONFIRM.

4 SETTING HOUR: PRESS CD 1 - SKIP DOWN BUTTON OR CD 1 - SKIP UP BUTTON TO SELECT THE

CORRECT HOUR. PRESS MODE BUTTON AGAIN TO CONFIRM.

5 SETTING MINUTE: AFTER STEPS 2 & 3 ARE COMPLETED, PRESS CD 1 - SKIP DOWN BUTTON OR

CD 1 - SKIP UP BUTTON TO SELECT CORRECT MINUTE. PRESS MODE BUTTON AGAIN TO

CONFIRM.

SETTING ALARM

1. DURING STANDBY MODE, HOLD TIMER BUTTON FOR 3-5 SECONDS. SETTING THE ALARM SEQUENCE

IS “ALARM ON TIME > ALARM OFF TIME > ALARM MODE > ALARM VOLUME”.

2. SETTING ALARM ON TIME: “ON” IS ILLUMINATED ON THE DISPLAY

i. SETTING HOUR: PRESS CD 1 - SKIP DOWN BUTTON OR CD 1 - SKIP UP BUTTON TO

SELECT THE CORRECT HOUR, THEN PRESS TIMER BUTTON AGAIN TO CONFIRM.

ii. SETTING MINUTE: PRESS CD 1 - SKIP DOWN BUTTON OR CD 1 - SKIP UP BUTTON

TO SELECT THE CORRECT MINUTE, THEN PRESS TIMER BUTTON AGAIN TO CONFIRM

3. SETTING ALARM OFF TIME: “OFF” IS ILLUMINATED ON THE DISPLAY:

i. SETTING HOUR: PRESS CD 1 - SKIP DOWN BUTTON OR CD 1 - SKIP UP BUTTON TO

SELECT THE CORRECT HOUR, THEN PRESS TIMER BUTTON AGAIN TO CONFIRM.

ii. SETTING MINUTE: PRESS CD 1 - SKIP DOWN BUTTON OR CD 1 - SKIP UP BUTTON

TO SELECT THE CORRECT MINUTE, THEN PRESS TIMER BUTTON AGAIN TO CONFIRM.

4. SETTING ALARM MODE: “TUNE”, “CD-1”, “USB” OR “CARD” IS ILLUMINATED ON THE DISPLAY:

i. PRESS CD 1 - SKIP DOWN BUTTON OR CD 1 - SKIP UP BUTTON TO SELECT THE

ALARM MODE, THEN PRESS TIMER BUTTON AGAIN TO CONFIRM.

ii. “TUNE”, “CD-1”, “USB” OR “CARD” (=SD CARD) ARE AVAILABLE FOR ALARM MODE

SELECTION.

5. SETTING ALARM VOLUME: “V - ” IS ILLUMINATED ON THE DISPLAY:

i. PRESS CD 1 - SKIP DOWN BUTTON OR CD 1 - SKIP UP BUTTON TO SELECT THE

ALARM VOLUME, THEN PRESS TIMER BUTTON AGAIN TO CONFIRM.

6. WHEN SETTING THE ALARM IS COMPLETE, THE DISPLAY WILL SHOW THE SETTING AGAIN FOR

CLARIFICATION.

7. “CLOCK” ICON WILL BE FLASHING WHEN ALARM IS IN ACTIVE. “CLOCK” ICON LIGHTS UP WHEN ALARM

SETTING IS STORED BUT NOT IN ACTIVE YET.

8. CANCEL ALARM: DURING STANDBY MODE, WHEN “CLOCK” ICON IS ON, PRESS TIMER BUTTON,

“CLOCK” ICON WILL TURN OFF.

TIMER FUNCTION

1. PUSH THE POWER KNOB UNTIL THE STANDBY INDICATOR LIGHT IS OFF.

2. WHEN THE UNIT IS TURNED ON, PRESS SLEEP BUTTON REPEATEDLY TO CHOOSE THE DESIRED

SLEEP TIME MINUTES FROM 90>80>70…..>10 OFF.

3. SLEEP TIME SETTING IS STORED WHEN THE “SLEEP” ICON LIGHTS UP ON THE DISPLAY.

BLUETOOTH CONNECTION

- PRESS AND HOLD FUNCTION BUTTON TILL LCD SHOWS “BT”, THEN THE UNIT IS READY

FOR CONNECTION WITH YOUR BLUETOOH DEVICE (SUCH AS MOBILE PHONE).

- SWITCH ON THE BLUETOOTH FUNCTION OF YOUR BLUETOOH DEVICE, AND SELECT

“ODCR2110 WD” BLUETOOTH EQUIPMENT FOR CONNECTION.

- AFTER YOUR BLUETOOH DEVICE IS CONNECTED WITH THE UNIT VIA BLUETOOTH, START

TO PLAYBACK YOUR DEVICE.

- THIS UNIT HAS NFC FUNCTION WHICH CAN ALLOW YOUR BLUETOOH DEVICE (SUCH AS

MOBILE PHONE) CONNECTING WITH THE UNIT AUTOMATICALLY.

 SWITCH ON THE BLUETOOTH AND NFC FUNCTION OF YOUR DEVICE, THEN PUT IT

NEAR THE “BT/N” LOGO WITHIN 5MM ON THE FRONT PANEL. YOUR DEVICE CAN

AUTOMATICALLY SEACH AND CONNECT WITH THE UNIT.

 TO DISCONNECT WITH THE UNIT, PUT YOUR DEVICE NEAR THE “BT/N” LOGO WITHIN

5MM ON THE FRONT PANEL AGAIN.

LISTENING TO RADIO & RECORDING TO USB/SD

NOTE: IT IS RECOMMENDED THAT A 4GB MEMORY STICK IS USED WHEN RECORDING TO USB

RADIO TUNING

1. PRESS TUNER / BAND BUTTON, SELECT AM OR FM BAND BY PRESSING TUNER / BAND BUTTON AGAIN.

2. TUNE TO THE REQUIRED STATION BY PRESSING CD 1 - SKIP DOWN

BUTTON OR CD 1 - SKIP UP

BUTTON FOR 1-2 SECONDS, AND THEN RELEASE.

3. THE UNIT WILL START SEEKING AUTOMATICALLY AND STOP WHEN A RADIO STATION IS FOUND.

MANUAL PRESET RADIO STATIONS

1. WHEN THE DESIRED RADIO STATION IS FOUND, PRESS MODE BUTTON, PROGRAM NUMBER WILL BE

FLASHING.

2. PRESS PRESET UP OR PRESET DOWN BUTTON TO CHOOSE THE PROGRAM NUMBER FOR STORING

THE DESIRED RADIO STATION.

3. PRESS MODE BUTTON AGAIN TO CONFIRM, PROGRAM NUMBER WILL STOP TO FLASH.

4. REPEAT STEP 2 & 3 UNTIL ALL DESIRED RADIO STATIONS ARE FOUND AND STORED

5. PRESS PRESET UP OR PRESET DOWN BUTTON TO CHOOSE THE PRESET RADIO STATIONS.

FM & FM-STEREO RADIO RECORDING TO USB/SD

1. PRESS FUNCT BUTTON TO SELECT “TUNE” MODE AND SELECT THE DESIRED BAND BY TUNER / BAND

BUTTON (AM OR FM).

2. INSERT MEMORY DEVICE (USB DRIVE, SD OR MMC CARD)

3. PRESS THE REC BUTTON; IT WILL TAKE 3-5 SECONDS TO READ MEMORY DEVICE. THEN USB OR SD

ICON WILL BE FLASHING.

4. PRESS CD 1 -

SKIP UP OR CD 1 - SKIP DOWN BUTTON TO SELECT DESIRED MODE

(USB OR SD) FOR ENCODING. THEN PRESS REC BUTTON AGAIN TO CONFIRM.

AND THE

SYSTEM IS STARTING THE ENCODING MODE AFTER FEW SECONDS.

5. IF ONLY USB DRIVE, SD OR MMC CARD IS INSERTED, STEP 4 CAN BE SKIPPED.

6. THE USB OR SD ICON WILL BE FLASHING ON THE DISPLAY DURING ENCODING.

7. TO FINISH RECORDING, PRESS REC BUTTON AGAIN AND DISPLAY WILL SHOW “END” AND RETURN TO

TUNER MODE.

PHONO & RECORDING TO USB/SD

NOTED:

- REMOVE THE STYLUS PROTECTOR.

- BE SURE THAT THE TONE ARM IS DETACHED FROM THE TONE ARM REST

BEFORE OPERATING AND RE-SECURED AGAIN AFTERWARDS.

1. REPEATEDLY PRESS FUNCT BUTTON TO SELECT “PHON” ON DISPLAY.

2. SET THE SPEED SELECTOR TO THE PROPER POSITION DEPENDING ON THE RECORD TO BE PLAYED.

3. PLACE THE RECORD ON THE PLATTER USING THE 45 RPM ADAPTOR IF REQUIRED.

4. PUSH THE LIFT LEVER UPWARD TO RAISE THE TONE ARM FROM THE ARM PARK,

AND THEN SLOWLY MOVE IT TO THE RECORD SIDE. THE PLATTER WILL START TO

ROTATE.

5. PUT DOWN THE LIFT LEVER TO DROP THE TONE ARM ON TO THE RECORD - THE VINYL RECORD WILL

NOW PLAY.

6. ONCE YOU HAVE FINISHED LISTENING TO YOUR RECORD YOU CAN RETURN THE ARM TO THE REST

EITHER USING THE LIFT LEVER OR MANUALLY.

7. IF YOU FIND YOUR RECORD STOPS PLAYING OR RECORDING HALF WAY THROUGH YOU WILL NEED

TO TURN OFF THE AUTO STOP FEATURE. THE SWITCH IS LOCATED NEXT TO THE SPEED ADJUSTMENT

SWITCH ON THE RECORD PLAYER DECK.

PHONO RECORDING TO USB/SD

1. PRESS FUNCT BUTTON TO SELECT “PHON” ON DISPLAY AND THEN INSERT MEMORY DEVICE (USB

DRIVE, SD OR MMC CARD).

2. PRESS THE REC BUTTON; IT WILL TAKE 5 SECONDS TO READ MEMORY DEVICE. THEN USB OR SD ICON

WILL BE FLASHING ON THE DISPLAY

3. PRESS CD 1 - SKIP DOWN BUTTON OR CD 1 - SKIP UP BUTTON TO SELECT DESIRED MODE (USB

OR SD) FOR RECORDING. THEN PRESS REC BUTTON AGAIN TO CONFIRM

4. IF ONLY USB DRIVE OR SD/MMC CARD IS INSERTED, STEP 3 CAN BE SKIPPED.

5. DISPLAY WITH SHOW “WAI” AND THEN USB OR SD ICON WILL BE FLASHING, WHICH MEANS THE SYSTEM

STARTS RECORDING.

7. NOW LOWER YOUR RECORD ARM TO START PLAYING- YOU ARE NOW RECORDING

6. TO FINISH RECORDING, PRESS REC BUTTON AGAIN AND DISPLAY WILL SHOW “END” AND RETURN TO

PHONO MODE.

CASSETTE TAPE & RECORDING

STOP / EJECT: PRESS TO STOP ALL DECK OPERATION. PRESS AGAIN TO OPEN THE CASSETTE DOOR.

FAST FORWARD: PRESS TO START, FAST FORWARD WINDING THE TAPE.

FAST REWIND: PRESS TO START, FAST REWIND WINDING THE TAPE.

PLAY: PRESS TO START PLAYING TAPE.

PAUSE: PRESS TO STOP TAPE OPERATION TEMPORARILY. PRESS AGAIN TO RESUME PLAYBACK.

RECORD: PRESS TOGETHER WITH PLAY BUTTON TO START TAPE RECORDING. (DECK A ONLY).

PLAYBACK

- PRESS FUNCT BUTTON TO SELECT “TAPE” ON DISPLAY.

- PUT IN CASSETTE TAPE.

- PRESS PLAY BUTTON ON CASSETTE DECK TO START PLAYBACK.

- USE PAUSE BUTTON WHEN YOU WANT TO STOP PLACKBACK TEMPORARILY.

- PRESS STOP / EJECT BUTTON WHEN FINISHED.

+ 16 hidden pages

TechPlay ODCR2110 WD Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual