Technoware ERA LED 1.5, ERA LED 2.0, ERA LED 2.6 User Manual

Uninterruptible Power Supply

ERA LED 1.5
ERA LED 2.0
ERA LED 2.6

User’s manual

UPS ERA LED 1.5 – 2-0 – 2.6 1 User’s manual

Index

Safety Warnings ................................................................................ 2

1 Introduction ................................................................................. 3

2 General Characteristics ................................................................... 4

3 Receipt and site selection ................................................................ 4

4 EXTERNAL DESCRIPTION .................................................................. 5

4.1 Front Panel ............................................................................. 5

4.1.1 Leds and ON/OFF Button .................................................................6

4.2 Rear Side ................................................................................ 7

5 Electrical Installation and First Start Up ............................................... 8

6 Functioning ................................................................................. 9

6.1 Normal Mode ........................................................................... 9

6.2 Battery Mode ........................................................................... 9

6.3 Low Battery and Automatic Restart ................................................. 9

6.4 Load Control .......................................................................... 10

6.5 Fault Condition ...................................................................... 10

7 Communication Interfaces .............................................................. 10

8 Technical Characteristics ................................................................ 11

9 Maintenance ............................................................................... 12

9.1 UPS Cleaning ......................................................................... 12

9.2 Battery ................................................................................ 12

9.3 Battery Replacement ............................................................... 12

9.4 Operator Safety ...................................................................... 13

10 Troubleshooting ........................................................................... 14

Conformity to the European Directives ................................................... 15

Product Disposal ............................................................................... 15

Lead Batteries ................................................................................. 15

© Copyright 2014 TECNOWARE s.r.l. All rights reserved.
All trademarks are property of their respective owners.

TECNOWARE s.r.l.
Via Montetrini, 2E – Loc. Molino del Piano – 50065- Pontassieve (FI) – Italy
www.tecnoware.com

Edition: September 2014 – version: 1.0

No part of this manual may be reproduced, even partially, without the
authorisation of TECNOWARE s.r.l.

TECNOWARE s.r.l. reserves the right to change specifications at any time
and without notice.

User’s manual 2 UPS ERA LED 1.5 – 2-0 – 2.6

Safety Warnings

 Read this manual carefully and completely before installing and using the TECNOWARE ERA LED

Uninterruptible Power Supply, which, from here after, will also be referred to as UPS.

 This manual should be kept close to the UPS and read before the UPS is installed and used.

 The UPS must be used only by properly trained personnel. To ensure correct and safe

operations, it is necessary that operators and maintenance personnel observe the general
safety Standards as well as the specific instructions included in this manual.

 Risk of electric shock: do not remove the cover. The UPS contains internal parts, which are at a

high Voltage and are potentially dangerous, capable of causing injury or death by electric
shock.

 There are no internal parts in the UPS, which are user serviceable. Any repair or maintenance

work must be performed exclusively by qualified technical personnel authorized by
TECNOWARE. TECNOWARE declines any responsibility if this warning is disregarded.

 Warning to the technical personnel authorized for Service: since internal components are

connected to the batteries, they will remain powered, and therefore dangerous, even after the
UPS has been disconnected from AC power mains. Before any repair or maintenance work,
disconnect the batteries, by removing the positive cable (red colour) from the positive pole of
the battery.

 It is compulsory to ground the UPS according to Safety Standards. The AC mains power supply

socket used to power the UPS must have an earth connection.

 In the event of AC main power supply failure (when the UPS works in Battery mode), do not

unplug the power supply cable to the UPS to ensure earth continuity to the connected loads.

 Since the AC mains power supply cable acts as a separation device, the AC mains power socket

used to supply the UPS and/or the rear side of the UPS must be accessible to easily disconnect
the cable in case of dangerous conditions.

 Risk of electric shock at the Output lines when the UPS is ON.

 Risk of electric shock at the Output lines while the unit is connected to the AC utility line.

 Do not obstruct ventilation slots or holes and do not rest any object on top of the UPS.

 Do not insert objects or pour liquids in the ventilation holes.

 Install the UPS indoors, in a protected, clean and moisture-free environment.

 Do not expose to the direct sun light.

 Do not keep liquids, flammable gases or corrosive substances near the UPS.

UPS ERA LED 1.5 – 2-0 – 2.6 3 User’s manual

1 Introduction

ERA LED is a Line Interactive UPS (Uninterruptible Power Supply) specifically designed to protect your computer
from any type of irregularities in the AC line (such as black-outs, under or over voltages, micro-interruptions),
which often cause damage to your Hardware and Software.

Under normal AC line condition, ERA LED performs output voltage regulation and filters frequently occurring
electrical disturbances (such as transients, spikes, interferences, etc.), thus protecting all devices connected to
the outlets, and recharging the batteries in an ideal way. In case of anomaly to the AC line, the UPS continues
feeding the protected equipment.

ERA LED is equipped with USB interface which can be used to notify a power failure or a low battery condition
directly to a computer: this makes it possible to automatically save your data during an extended black-out with
the most widespread operating systems (Windows, Mac OS X, Linux, etc.).

Read this manual carefully before using the ERA LED; it includes important safety
warnings and useful advices for correct use and installation.

This manual is a guide that enables you to correctly install and use your ERA LED. This
manual includes important SAFETY instructions for the operator, for the UPS correct
installation, and gives useful advice on the product and battery maintenance. For any
type of problem, please refer to this manual before calling the customer service.

ERA LED is constantly being developed and improved: consequently, your unit may differ somewhat from the
description contained in this manual.

This manual includes the following models:

• ERA LED 1.5 (1.5 KVA)

• ERA LED 2.0 (2.0 KVA)

• ERA LED 2.6 (2.6 KVA)

In this manual ERA LED will simply be referred to as UPS.

User’s manual 4 UPS ERA LED 1.5 – 2-0 – 2.6

2 General Characteristics

ERA LED has all the advanced features, which guarantee maximum reliability and safety:

• All functions are controlled by a microprocessor, giving full guarantee of high reliability.

• Output Voltage regulation through AVR (Automatic Voltage Regulation).

• Overload protection both in normal mode and in battery mode.

• High performance battery charger, which extends the battery medium life ensuring an optimal recharge.

• Start up even if the electrical network is not available.

• Automatic restart after an automatic shut down due to a low battery condition once the AC utility power

returns.

• Adapts automatically to 50 or 60 Hz input frequency.

• 3 Leds to show the functioning modes, alarm and fault conditions.

• Acoustic signals of various kinds indicating functioning modes and alarm/fault condition.

• Communication with the computer through USB interface.

• Protects and filters the telephone line.

• Fast swappable battery.

• High efficiency

• Maximum reliability

• Smart design and easy to use

3 Receipt and site selection

Carefully remove the UPS from its packaging, and carry out a meticulous inspection. We recommend keeping the
original packaging in a secure place, in case you need to send the UPS for maintenance purposes. In case of
transport damage, notify the carrier and dealer immediately.

We recommend paying attention to the below points in order to choose a correct placement for your UPS:

• The UPS is designed to operate in a protected environment (e.g. offices). We therefore recommend
installing it in a place with very little or no humidity, dust or smoke.

• In all circumstances, see the “Technical Characteristics” chapter for environmental specifications and
check that the selected area meets these specifications.

• During normal operation the UPS discharges a minimal amount of heat. So it is necessary to leave at least
20 cm of unobstructed space all around the UPS in order to keep it properly ventilated.

• Do not obstruct ventilation holes.

• Do not insert objects or pour liquids in the ventilation holes.

• Do not rest any object on top of the UPS.

• Do not keep liquids, flammable gases or corrosive substances near the unit.

• Install the UPS on a properly tiled floor. Avoid the installation on a floor that is not tiled flat.