Technotherm CPH 1000, CPH 2400 Installation And Technical Manual

D

THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE

REFERENCE. BE SURE TO OBSERVE ALL LABELS AND WARNINGS ON THE APPLIANCE

Edition: 01/14

Id Nr. 911 360 860

Installation and technical manual

Panel Heater CPH 1000 - 2400

GB

2 Edition:01/14

Manual

CPH 1000 - 2400

1. Important Safety instructions

• People (including chi ldren) who are l imited in t heir ph ysical, se nsory, or m ental ca pacities s hould
not use this device at any tim e. Furtherm ore do not h andle this instrument if you do not possess
the necessary experienc e and know ledge to do s o. This de vice s hould onl y be hand led under the
supervision of a qualified person and after a t hor o ugh intr od ucti on.

• Do not leave childr en alone with the d evice, and supervise th em at all times to keep them from
getting harmed.

• WARNING: Do not cover! Otherwise this instrume nt will overheat.

• Do not place the heater underneath a socket, drainage or the like.

• To keep from getting burned, do not touch heater´s surface whenever it is turned on.

• Please use the handle whenever you have to move the heater.

• Do not put the cord underneath the carpet or a rug and make sure that it is not a tripping hazard.

• Plug the heater into properly grounded sockets only.

• Do not use the heater in any other way than des cribed in the user m anual. Any other way of us e

may lead to fire, electrocution, and may cause serious harm to the person.

• Do not use this device near bathtubs, showers or swimming pools.

• In case the connection cable is dam aged it has to be replaced by the m anufacturer or someone

commissioned by the manufacturer.

WARNING: Do not use a switching-oriented device, like a timekeeper, when operat ing this heater.
This could cause a change in the thermal adjustment which is potentially hazardous!

• To keep the device from overheating, do not put towels or clothing on top.

• When using the heater, make sure it is in an upright position an d positioned on a even and dry

place.

• Do not put any fore ign objects into the ven t. This m ay cause electr ocution, fir e or dam age to the
heater.

• Do not use an extension cord unless approved by an electrician.

• This device is for private use only, do not use in any other way than intended by the

manufacturer.

• Do not use the device near curtains, highly combustible, extremely explosive or malleable
materials.

• Keep a distance of a at least 1.0 m between combustible materials- like furniture, cushions,
bedding, paper, clothing, curtains-and the heating device.

• Do not use the device in rooms were petrol, paint or any other flammable liquids are stored.

• Do not use the device outside.

Warning! This device has to be grounded

This device may only be operated using alternating current and the operating voltage indicated

on the power rating plate.

• Nominal Voltage 230V AC, 50 Hz

• Protection Class I

• Degree of Protection IP 24

• Room Thermostat 4°C till 40°C

GB

3 Edition:01/14

Manual

CPH 1000 - 2400

2.1 Technical data

Model

Power [W]

Dimensions (ill.)

a [mm] b [mm] weight [kg]

CPH 1000

1000

415

215

4,8

CPH 1500

1500

565

365

6,0

CPH 2000

2000

695

495

7,0

CPH 2400

2400

915

715

8,2

2. 2 Operation

Connect the heating convector to the mains supply
to set it into operation.

Switching the appliance on

Switch on the appliance by setting the tumbler switch
to position „1“.

Switching the heating on

Switch on the heating by turning the temper atur e selector switch and choose the required temperature.
The temperature range ex tends from 4°C to 40°C gra duated into 10 steps. The ther mostat switches off
the heating as soon as t he preset ambient tem perature is reached, whic h will then be kept constan t by
cyclic heating. The high consistency of the thermostat (below 2 K) provides a constantly comfortable
temperature and thus ensures power-saving heating.

Anti-freezing protection

When setting the temperature selector switch to grade „1“ the thermostat automatically cuts in if the
ambient temperature falls below 4°C.

Switching the appliance off

Switch off the appliance by setting the tumbler switch to position „0“.

3. Important notes

During operation the temperature at the front panel and at the hot-air outlet of t he convector may rise
above 85 °C. Do not place an y objects on or beside the heater , do not put anything bet ween the heater
and the wall. Free air exit must not be hindere d by covering th e hot-air outlets with any objects such as
curtains, p ieces of laundr y etc., other wise risk of overheating. Combustible obj ects suc h as wood, paper,
textiles etc. as well as highly flammable substanc es such as wax, petr ol, aerosols must not be placed
near the heater within the hot-air current. Switch the heater off when carrying out work where highly
flammable vapors could emerge, such as laying or sealing parquet or other kinds of floor covering or
when using aerosols, floor wax, petrol etc.

GB

4 Edition:01/14

Manual

CPH 1000 - 2400

Caution!

The appliance must not be installed in rooms with explosion hazard such as garages etc.
Remove the protecti on f oi l f rom all panels prior to f irs t us e. S ho uld t h e h eat er g ive of f a bad smell
when it is heated up for the firs t time this is c aused by m anufac turing-relate d residues , which are
harmless to health. T his nuisance will disappear with in short time. The rising hot air can c ause
staining on the wall, a phe nomenon seen in all other types of heaters too. T he appliance may
only be opened by an authorized professional with the power supply disconnected.

4. Maintenance

To clean the appliance, switch it off and rub it with a moist cloth using a mild detergent if necessary.
Finally polish with a dry cloth. Do not use any abrasive or caustic detergents for cleaning.

This Manual is very important and h as to be k ept at a saf e place at all times . Be sure to hand th is m anual
to any other succeeding owner of the device.

5. Installation instructions

These installation instruc tions are an integral part of the ap pliance and must be kept in a saf e place by
the user. Pass it o n to any subsequent user if the owner of the appliance changes. W all convectors are
direct electric heater s that are ex clusivel y intended for being f ixed to m assive walls. T hanks to graduated
heating capacities they can be adapted to any room size. The conv ect or c omes complete with connec t ing
cable that must be connected to a wall socket. The appliance has been designed to be connected to
230V alternating current (AC).

Fixing

Fix the appliance in such way that any potentially c ombustible objects cannot cat ch fire. Therefore, the
minimum safety distances mentioned below must be kept. Fix the heater to an upright wall that is
resistant to a minimum temperature of 90°C.

Keep a distance of 25 cm to the floor. T here sha ll be a minim um s pace of 10 cm bet wee n the heater and
any wooden parts or other objects. Any window sills, roof slopes, brackets etc . must be located at least
50 cm over the hot-air outlets of the heater. If the appliance is used in bathrooms, instal l it in such way
that the tumbler s witch or the temperature selector cannot be touched b y a person being in the t ub or
under the shower. When fixing the appliance to the wal l obser ve t he dimensions given in Fi g. 1 an d f ollow
all other instructi ons f or inst all ati on. Dr i ll t wo ho les of 7mm and fix the ap propr i ate plu gs. Screw in the two
4 x 25 mm screws so th at a distance of 1 – 2 mm is kept between screw head and wall. Hang up the
appliance on the suspensi on brac k ets which are fixed to the back of the heater a nd pus h it to the left until
it stops. Then tighten the le f t -hand s c rew throug h the a ir exit grille and the provided hole in the bac k panel
of the heater. Now the appliance is secured against unintended removal.

Caution Do not install the appliance below a wall socket. The appliance is not suitable for
outside use.

GB

5 Edition:01/14

Manual

CPH 1000 - 2400

Electrical installation

The appliance has been designed to be connected to 230V alternating current (AC). All electrical
installation work, in particular protective m easures, must be carried out in com pliance with the national
regulations and statutory provisions of the respective utilities provider.

The electrical installat ion may only b e carried out in compliance with the installation instructions
by an authorized professional!

The appliance has been d esigned for fixed connection. Therefore, it is necessary to install a co nnector
socket for fixed connection where the connecting cable of the appliance.

H05 VVF 3 x 1.0 mm

2

(power class 1000 W)
H05 VVF 3 x 1.5 mm

2

(power class 1500 W- 2400 W)

Permanent cables m ust not be connected direc tly to the appliance! If the electrical installation is don e by
means of an isolating unit, it should be taken care that the isolation is designed with at least 3 mm
separation on all poles.

Type of connection of the appliance:
Type Y acc. to VDE 0700 Part 1.

In case the connecting cable is damaged, it may only be replaced by a repair shop appointed by
the manufacturer!

The minimum distance between appliance and connector socket must be 10 cm. The connecting cable
must not have contact with the appliance.

GB

6 Edition:01/14

Manual

CPH 1000 - 2400

Diagram of connections

Lucht LHZ Elektroheizung GmbH & Co. KG
Obere Hauptstr. 61
D 09232 Hartmannsdorf
Fon: [phone]
Fax: [phone]
E-mail: [e-mail]
Web: www.technotherm.com

TECHNOTHERM Support:

Fon: [phone]

GB