Technoline WT 180 Instruction Manual

WT 180 - Radio controlled alarm clock

Instructions manual

Front view

Back view

Part A - LCD Part B - Buttons Part C - Structure

A1: DCF icon B1: “SNOOZE/LIGHT” button C1: Battery Compartment
A2 : Radio controlled time B2: “MODE/SET” button
A3: Alarm icon B3: “+(12/24)” button
A4: Month and date B4: “-(°C/°F)” buttton
A5: Temperature B5: “AL ON/OFF” button

B6: “RESET” button

Set up and radio controlled time

•

Insert 2 x AA batteries (not included) by observing the correct polarity signs (+/-) inside the battery compartment.

• The clock automatically starts scanning the RF 433MHz signal to register new thermo sensor unit after new

batteries inserted. After registered the thermo sensor or press “CHANNEL” button to stop scanning, the clock
will then automatically starts scanning the DCF time signal (“

” flashes on the LCD).

“

” flashes indicate now is receiving the DCF signal.

“

” turns on indicate signal received successfully.

“DST” show on the LCD if it is in Daylight Saving Time Mode.

• The clock automatically scans the time signal at 3:00a.m. everyday to maintain accurate timing. For failed

reception, scanning stops (“

” on LCD disappear) and repeats again at 4:00a.m, 5:00a.m, and 6:00a.m.

• The clock manually scans the time signal by holding buttons “+” (B3) and “- “(B4). For failed reception,

scanning stops (“

” on LCD disappear) and repeats again in the next 4 hours (4 times) until received. e.g.

:00.

Stop scanning by holding “+” (B3) and “-“(B4) buttons 3 second.

en insert batteries again and use a pin to press “RESET” (B6) to reset the unit if it

ch as computer monitor or TV sets.

The clock loses its time information when the battery is removed.

1.

old “+” (B3) and “-” (B4) to adjust the Hour, Minutes, Time zone, Language of week day, Year, Month

. Press “MODE” (B2) button to confirm each setting.

rk. The languages and their selected abbreviations for each day of the week are sho wn in the follo wing

table:

Language Sunday Monday Tuesday Wednesday Thursday Friday Saturday

scan at 8:20 failed, it will received again at 9:00; 10:00; 11:00; 12

•

Notes:

• Buttons will not function while scanning for DCF time signal unless they are well received or stopped manually.

• Remove batteries and th

does not work properly.

• Avoid placing the clock near interference sources/metal frames su

•

Manual time setting

Press “MODE” (B2) button to change the display content:
Radio Controlled Time Æ Time + weekday Æ Alarm Time

2. When the time is displayed on LCD, hold “MODE” (B2) button for 2 seconds to enter time setting mode.

3. Press or h
and Day.

4

Notes:

• 7 languages can be selected for day-of-week-display: German, English, French, Italian, Spanish, Dutch and

Denma

German, GE SO MO DI MI DO FR SA
English, EN SU MO TU WE TH FR SA
French, FR DI LU MA ME JE VE SA
Italian, IT DO LU MA ME GI VE SA
Spanish, ES DO LU MA MI JU VI SA
Dutch, NE ZO MA DI WO DO VR ZA
Denmark, DA SO MA TI ON TO FR LO

• The time zone is used for the countries where can receive the DCF time signal but the time zone is different

from the German time. When the country time is faster than the German time for 1 hr, the zone should be set
to +1. Then the clock will automatically set 1 hour faster from the signal time received.

Snooze alarm function

1. Press “AL ON/OFF” (B5) button to switch the alarm on. “ ” appears on the LCD.

2. Press “MODE” (B2) button twice to turn to alarm time display, hold “MODE” (B2) button 2 seconds (hour digit

for 8 minutes, then it alerts again.

. Press “AL ON/OFF” (B5) button to switch off the alarm. (“

blink) to enter alarm time setting mode.

3. Press “+” (B3) or “-” (B4) buttons to adjust the alarm time.

4. Press “SNOOZE/LIGHT” (B1) button when alarm is alerted. The alarm snoozes

5 ” disappear).

Press “°C/°F” (B4) button to select thermometer in Celsius or Fahrenheit mode.

Press “12/24” (B3) button to select 12 or 24 hours mode.

Thermometer

•

12/24 Hr

•