Techno Line WS 9767 User guide

WS9767 - INSTRUCTION MANUAL

TEMPERATURE STATION WITH RADIO CONTROLLED CLOCK AND ALARM

ENVIRONMENTAL RECEPTION EFFECTS

The temperature station obtains the accurate time with wireless technology. Same as all wireless devices, the reception is maybe affected by the following circumstances:

∙Long transmitting distance

∙Nearby mountains and valleys

∙Among tall buildings

∙Near freeway, railway, airports, high voltage cable etc.

∙Near construction site

∙Inside concrete buildings

∙Near electrical appliances (computers, TV’s, etc)

∙Inside moving vehicles

∙Near metallic structures

Place the temperature station at a location with optimal signal, i.e. close to a window and away from metal surfaces or electrical appliances.

QUICK SETUP

1.Keep the temperature station and outdoor sensor next to each other. Slide open the battery cover at the back of the outdoor sensor. Make sure the channel selector is set at position CH1 (when using multiple transmitters: for second transmitter CH2, for third transmitter CH3), then insert 2 x AAA batteries (not included) into the outdoor sensor by observing the correct “+/-“ polarity signs inside the battery com partment. Replace the battery door.

2.Slide open the battery cover at the back of the temperature station, then insert 2 x AA batteries (not included) by observing the correct “+/-“ polarity signs inside the battery compartment. Then replace the battery cover.

3.Peel off the protective label on the front. The temperature station is ready to work for you.

The temperature station will receive data signal from the outdoor sensor in few seconds. Then place the outdoor sensor in a dry and shaded area outdoor.

DCF SIGNAL RECEPTION AND SIGNAL INDICATOR

The time base for the radio controlled time is a Cesium Atomic Clock operated by the Physikalisch Technische Bundesanstalt Braunschweig which has a time deviation of less than one second in one million years. The time is coded and transmitted from Mainflingen near Frankfurt via frequency signal DCF-77 (77.5 kHz) and has a transmitting range of approximately 1,500 km. The clock of the temperature station receives this signal and converts

it to show the precise time in summer or wintertime.

The quality of the reception depends greatly on the geographic location. In normal cases, there should be no reception problems within a 1500 km radius around Frankfurt.

After the temperature station is powered up, it starts to receive DCF signal. The icon flashes.

Receiving DCF signal	( icon flashing)
Successful reception	( icon becomes static)
Failed reception	( icon disappear)

Note: The DCF-77 reception is only available in Europe. Outside the reception range the clock of the temperature station is usable as normal quartz clock.

MANUAL TIME SETTING

1.Press and hold the CLOCK button for 2 seconds, the time display format 24Hr flashes. Press the SET/RESET button to select the 12h or 24h time display format.

2.Then press the CLOCK button again, language for weekday display GE flashes. Press the

SET/RESET button to select the language for weekday display (GE – German, FR – French, SP – Spanish, IT – Italian, EN – English).

3.Then press the CLOCK button again, time zone digit O flash. Press the SET/RESET button to select the time zone (± 12h).

4.Then press the CLOCK button again, the hour digits flash. Press the SET/RESET button to set the hours.

5.Then press the CLOCK button again, the minute digits flash. Press the SET/RESET button to set the minutes.

6.Then press the CLOCK button again, the year digits flash. Press the SET/RESET button to set the year.

7.Then press the CLOCK button again, the month digits flash. Press the SET/RESET button to set the month.

8.Then press the CLOCK button again, the date digits flash. Press the SET/RESET button to set the date.

9.Press the CLOCK button again to store the settings and return to normal time display. The clock will automatically return to normal mode in around 30 seconds if no further press of any other buttons.

ALARM SETTING

1.Press and hold the ALARM button for 2 seconds, the AL icon appears on the display, the hour digits flash. Press the SET/RESET button to set the desired alarm hours.

2.Press the ALARM button again, the minute digits flash. Press the SET/RESET button to set the desired alarm minutes.

3.Press the ALARM button again to store the alarm settings and return to normal time display. The clock will return to normal mode in around 30 seconds if no further press of any other buttons.