Techno Line WS 9116 INTRODUCTION

INTRODUCTION WS 9116

FEATURES:

• Four digit time display

• 12-hour or 24-hour selectable time

• Indoor temperature (°C or °F)

• Outdoor temperature (°C or °F)

• Minimum and Maximum temperature

• Four level RF strength indicator

• Wall hanging or free standing

• Low battery indicator for receiver and transmitter

SET UP:

NOTE: This temperature station can receive one transmitter only.

• First, insert batteries into the transmitter, observing the correct polarity (see
marking inside battery compartment). Keep transmitter 5-10 feet from the
temperature station.

• Within 30 seconds of powering up the transmitter, insert batteries into the
Temperature Station, observing the correct polarity (see marking inside battery
compartment). Once the batteries are in place, all segments of the LCD will
light up briefly.
Following the indoor temperature will be displayed. If the indoor temperature is
not shown in the LCD after 60 seconds, remove the batteries and wait for at
least 60 seconds before reinserting them. Once the indoor data is displayed
you may proceed to the next step.

• After the batteries are inserted, the Temperature Station will start receiving
outdoor temp data from the transmitter. The outdoor temperature should then
be displayed on the Temperature station. If this does not happen after 2
minutes, remove the batteries from both units and start again from the
beginning.

• In order to ensure sufficient 433 MHz transmission, the outdoor transmitter
should be placed a distance of no more than 100 feet (30 meters) from the
Temperature Station and the transmitter.

TEMPERATURE SELECTION:

FAHRENHEIT/CELSIUS: Press the CF/SET button once to switch from
Celsius to Fahrenheit.
FOUR LEVEL RF INDICATOR: The temperature station will indicate strength
of signal reception from the outdoor transmitter by the number of bars on the
RF indicator icon.
4-bars: Shows after initial set up and stays when reception is at full strength.
3-bars: Indicates one reception failure from the outdoor transmitter.
2-bars: Indicates two reception failures from the outdoor transmitter.
1-bar: Indicates three reception failures from the outdoor transmitter.

0-bars: Indicates four reception failures from the outdoor transmitter.
The antenna symbol will flash on initial set while searching for the signal. If it
fails to receive a signal after 63 minutes the temperature station will display
dashes (“--.-“). The temperature station will search again for a signal for 3
minutes every next hour.

SET TIME:

• 12/24-HOUR TIME: Hold the CF/SET button until
12hr or 24hr flashes.
Press the MIX/MAX/+ button to switch between 12-hour and 24-hour time.
Press the CF/SET button once to continue.

• HOUR: The Hour will flash. Press the MIX/MAX/+ button to change the hour.
Press the CF/SET button once to continue.

• MINUTES: The minutes will flash. Press the MIX/MAX/+ button to change the
minutes.

• NOTE: Hold the MIX/MAX/+ button to move quickly through the numbers.
Press CF/SET once and you are done.
MIN/MAX RECORDING:

• VIEW MIN/MAX: Press the MIN/MAX/+ button to view indoor and outdoor
MAX, MIN and Current temperature.

• RESET MIN/MAX: Hold the MIN/MAX/+ button for 3 seconds to reset all
MIN/MAX readings to current temperatures.

RESET BUTTON:
The Temperature Transmitter has a RESET button. Use a small pointed object
to gently press and release to send a signal. Follow the instructions for in SET
UP regarding the display.
NOTE: Removing power from the transmitter and display negates the need for
the RESET button.

SPECIFICATIONS:
Indoor Temperature:
Range: 0° C to 50° C (32° F to 122° F)
Resolution: 1°C /°F
Outdoor Temperature:
Range: -30° C to -60° C (-22° F to 140° F)
Resolution: 1°C /°F
Power:
Receiver: 2-AAA
Transmitter: 2-AA
Dimensions:
Receiver: 65x30x95.7mm
Transmitter:47x28.2x104mm