Technoline WS 7019 Instruction Manual

INSTRUCTION MANUAL OF WS 7019

ENVIRONMENTAL RECEPTION EFFECTS

Your radio controlled clock obtains the accurate time with wireless technology. Same as
All wireless devices, the receiving ability maybe affected by, but not limited to, the following
circumstances:

 Long transmitting distance
 Nearby mountains and valleys
 Among tall buildings
 Near railway, high voltage cable etc.
 Near freeway, airport, etc
 Near construction site
 Inside concrete buildings
 Near electrical appliances
 Neat computers and TV’s
 Inside moving vehicles
 Near metallic structures

Place your clock at a location with optimal signal, i.e. close to a window and way from metal surfaces or
electrical appliances.

Step 1

Inset the stand to the bottom of your weather station.

Step 2 Slide open the battery cover at the back of your weather station, then insert 3 x AA alkaline

batteries into the battery compartment to the back of your weather station by observating the correct +/­polarity signs inside the battery compartment. Replace the battery cover.

Step 3 Keep your Weather Station and wireless sensor next to each other. Slide open the battery

cover at the back of your wireless outdoor sensor, then insert 2 x AA alkaline batteries to the back of it.
Replace the battery cover. Your weather station will receive data signal from the outdoor sensor in few
seconds. Then place your outdoor sensor in a dry and shaded area outdoor.

Step 4 Peel off the protective label on the front. Your Weather Station is ready to work for you.

Step 5 After your weather station receives the outdoor temperature and humidity, it will start to search

for the DCF signal. This may take overnight. In case your weather station does not catch the DCF
signal during the day, set the clock manually.

Remarks:

1. Keep in mind that your outdoor sensor has a 100-feet open air transmission with no obstructions.
Actual transmission range will vary depending on what is in the path of the signal. Each obstruction
(roof, walls, floors, ceilings, thick trees, etc.) will effectively cut signal range in half.

2. During reception of the DCF time signal, all buttons do not function and your weather station does
not take temperature and humidity measurement. After first time installation, the temperature and
relative humidity readings will get stable and become more accurate in around 30 minutes.

3. The backlight of LCD is on when the user press the Snooze / Light button.

DCF SIGNAL RECEPTION AND SIGNAL INDICATOR

After your clock is powered up, it starts to receive DCF signal. The icon flashes.

Weak or no DCF signal (only

icon flashing)
Receiving strong DCF signal (
Successful Reception (
Failed Reception (

icon flashing)
icon becomes static)
icon disappear)

Remark : when your clock is receiving radio controlled time signal, all buttons except the snooze / light
button do not function.

DCF TIME SIGNAL RECEPTION

Your weather station will automatically update itself to the exact time after receipt of the DCF time code.
This typically takes over night. The clock will automatically attempt to receive the DCF signal every
night at 1:00 am, 2:00 am, 3:00 am, 4: 00 am and onwards. If it receives DCF signal at 3:00 am it will
stop receiving until 1: 00 am next day.

To start DCF reception manually, press WAVE / - / °C/°F button for 2 seconds. To stop DCF reception,
press and hold WAVE / - / °C/°F for 2 seconds.

TO ADJUST THE VIEWING ANGLE

You could adjust your weather station clock to 3 different angles for better viewing.

Remark: Do not over push the top case backward with force or you may break the stand.

TO SET CALENDAR, TIME, 12/24 HR TIME FORMAT

1. Press and hold SET / ALM SET for 2 seconds, time digits change to year “2009” and flash. Press + /

- to set year.

2. Then press SET / ALM SET once again, month digits flash. Press +/- button to set month.

3. Then press SET / ALM SET once again, date digits flash. Press +/- button to set date.

4. Then press SET / ALM SET once again, time digits change to “00”, press +/- to select time zone: -

“00” = GMT +1 hour (e.g. Germany)
“01” = GMT +2 hours (e.g. Finland)
“-01” = GMT 00 hour (e.g. U.K.)

6. Then press SET / ALM SET once again, hour digits flash. Press+/- to set the hours.

7. Then press SET / ALM SET once again, minute digits flash. Press +/- button to set the minutes.