ASSEMBLY INSTRUCTIONS
MODEL RTA - 2336
Thanks for purchasing one of our products.
Please read carefully the assembly instructions before the installation.
Please save this manual for future reference.
MODEL RTA- 2 3 3 6
RTA- 2336
RTA-2336
PARTS LIST
25
P.3
19
24
7
9
2
10
Left Panel
4
20
21
1
Right Panel
5
2
Bottom Panel Bottom Front Panel
6
3
7
X2 SETS
Left
4
8
Right
Back Panel
Top Drawer Front
Panel
Middle Front Panel
9
Bottom Drawer Front
Panel
10 11 12
Top Panel Slider
X2 X2
Drawer Left Panel Drawer Right Panel
RTA-2336
P.4
Drawer Bottom Panel
Rotating Structure
20 21
Drawer Back Panel
Support Tube
1413 16
15
X4X2X2 X6
Drawer Connect Studs
1817
19
X2
Big Table Top
22
23
Back Structure
Caster
Front Structure
Small Tabl e Top
27
X2
Short Connect Tube Long Connect Tube
2624 25
X2
Big Side Panel Support Structure
RTA-2336
SCREWS LIST
P.5
PART
A
B
C
D
E
F
G
H
QT Y.
24
24
16
20
8
4
4
6
IT EM PART
3X15 MM
6X40 MM
4X14 MM
6X15 MM
4X35 MM
6X20 MM
6X40 MM
6X50 MM
J
K
QT Y.
I
6
6
1
1
1
IT EM
6X25 MM
M6
Φ16MM4
30mm
RTA-2336
P.6
RTA-2336
ASSEMBLY STEPS:
P.7
1
12
11
15
Use screws A to assemble the Drawer Connects (15)
to the Drawer Left and Right Panels (11 & 12).
SCREWS
3X15 MM
A
4PCS
3
14
13
12
2
12
11
&
9
Use screws D to assemble the Drawer Connects (15)
to the Top Drawer Front Panel and Bottom Drawer
Front Panel (9 & 10).
SCREWS
6X15 MM
D
Slide in the Drawer Bottom Panel (13).
Use screws E to assemble the Drawer
Back Panels (14) to the Drawer Left and
Right Panels (11 & 12) .
12
10
2PCS
4
11
Left
8
12
Right
8
11
SCREWS
4X35 MM
E
4PCS
Grab the 2 sets of the Drawer Sliders (8) and separate the flat
ones from the “L” shaped ones. Place the drawer upsidedown as shown and use screws A to assemble the “L” shaped
Sliders to the Drawer Left & Right Panels (11 & 12) as show n.
IM PORTANT: R EFER TO THE DRAW IN GS FOR TH E CO RRECT
PO SITION OF T HE SLIDER S. I f they get in stalled i ncorrec tly,
the drawers will raise 1" with a gap at the bottom and the top
drawer will not close!
RE PE AT STE P 3 TO 4 FO R TH E OT HE R DRAWER
SCREWS
3X15 MM
A
4PCS
5
RTA-2336
P.8
20
6
16
2
1
16
Insert the Studs (16) to the Left Panel, Right Panel,
Back Structure and Front Structure (1,2,20 & 21).
21
16
16
1
X2
8
Left
Grab 2 sets of the Flat Sliders (8) and use screws A to assemble
them to the Left & Right Panels (1 & 2) as shown.
The wheel on the sliders go facing to the FRONT and the sc rew
goes on the hole after the wheel as shown.
Please pay attention to the direction of the panles.
8
Right
2
X2
SCREWS
3X15 MM
A
8PCS
7
RTA-2336
5
P.9
3
4
First screw bolts B to the Bottom Front Panel and Back Panel (4 & 5 ),
then assemble the Bottom Panel (3) as shown and as explained in page 5.
8
2
5
6
1
3
4
First screw bolts B to the Left Panel (1) and Right Panel (2), then
assemble the Bottom Panel, Bottom Front Panel, Back Panel and
Middle Front Panel (3,4,5 & 6) as shown and as explained in page 5.
SCREWS
6X40 MM
B
SCREWS
6X40 MM
B
4PCS
14PCS
9
7
1
First screw bolts B to the Top Panel ( 7), then as semble it t o the Left
and Right Panel (1 & 2) as shown and as explained in page 5.
2
SCREWS
6X40 MM
B
4PCS
10
RTA-2336
P.10
21
11
20
20
23
21
Use screws G to assemble the Long Connect
Tube (23) to the Back Structure and Front
Structure (20 & 21).
SCREWS
6X40 MM
G
4PCS
Use screws F to assemble the Short Connect
Tube (22) to the Back Structure and Front
Structure (20 & 21).
12
22
19
18
SCREWS
6X20 MM
F
4PCS
Use screws C to assemble the Support
Tube (18) to the Big Table Top (19).
SCREWS
4X14 MM
C
8PCS
13
RTA-2336
19
20
P.11
21
Use screws H to assemble the Back Structure, Front
Structure and Long Connect Tube (20,21 & 23) to the
Big Table Top (19) .
23
SCREWS
6X50 MM
H
6PCS
14
15
24
25
25
First screw bolts B to the Small Table Top (24) , then
assemble it to the Big Side Panel (25) as shown and
as explained in page 5.
SCREWS
6X40 MM
B
2PCS
Use screws D to assemble the Support Structures (26)
to the Small Table Top an d Big Side Pa nel (24 & 25) .
24
26
X2
SCREWS
6X15 MM
D
8PCS
16
RTA-2336
P.12
27
25
18
24
Use screws C to assemble the Support Tube (18) to the Small Table Top (2 4).
Use screws I & J to assemble the Casters (27) to the Big Side Panel (25).
17
18
17A
17B
17D
17C
17E
17
SCREWS
C
J
24
4X14 MM
6X25 MM
I
2PCS
M6
8PCS
2PCS
17E
17D
17C
17D
17E
17D
Use Allen Wrench to di sassemb le the Rota ting
Structure (17) as shown.
NOTE: It is recommended to keep all the parts
for (17) laid out in the same order shown above
for easy re-assembly later.
17F
Use screws D to assemble one of the part 17E to the
Small Tabl e Top (2 4).
SCREWS
6X15 MM
D
4PCS
19
RTA-2336
P.13
17A
17B
20
17D
17D
17D
17D
17C
17C
17E
17F
Use Allen Wrench to as semble th e Rotatin g
Structure (17) as shown.
17A
7
Use screws I, J & K to assemble the Rotating Structure (17)
to the Top Panel (7) as shown.
SCREWS
6X25 MM
I
4PCS
M6
J
K
Φ16 MM
4PCS
4PCS
21
RTA-2336
P.14
19
17E
22
Use screws D to assemble the Rotating Structure (17)
to the Big Table Top (19) .
9
SCREWS
6X15 MM
D
4PCS
10
Tighten any and all screws.
Insert the drawers into the cabinet, starting with the bottom drawer.
You might have to insert it at a downward tilted angle.
CARE AND MAINTENANCE
English
- DO NOT EXPOSE THE SURFACES TO DIRECT SUNLIGHT OR EXTREME
ENVIRONMENTAL CONDITIONS. ANY DAMAGE RESULTING FROM SUCH
EXPOSURE IS NOT COVERED BY THE PRODUCT’S WARRANTY.
- THE PREFERABLE METHOD TO CLEAN THE SURFACES IS TO WIPE THEM
USING A SOFT CLOTH DAMPENED WITH A SOLUTION SOAP AND WATER,
THEN DRY WITH A CLEAN TOWEL.
- DO NOT SPRAY SOLVENTS OR CLEANING AGENTS DIRECTLY OVER THE
SURFACES, STRUCTURAL TUBES OR METAL PARTS.
- DO NOT LEAN, SEAT OR STAND OVER THE UNIT.
- DO NOT ALLOW CHILDREN TO PLAY OVER/UNDER THE UNIT, NOR ALLOW
THEM TO REACH INSIDE ANY COMPARTMENTS WITHOUT THE SUPERVISION
OF AN ADULT.
- BEFORE MOVING OR TRANSPORTING THE UNIT, MAKE SURE THAT:
ALL HEAVY OBJECTS OR THAT MIGHT FELL OFF ARE REMOVED FROM
THE UNIT.
IF THE UNIT ARE ON CASTERS (WHEELS), MAKE SURE THAT ALL ARE
UNLOCKED.
THE UNIT MUST BE HANDLED BY AT LEAST 2 PERSONS.
WHEN LIFTING THE UNIT, USE BOTH OF YOUR HANDS, AND BEND YOUR
KNEES. REMEMBER TO ALWAYS LIFT WITH YOUR LEGS, NOT YOUR BACK.
- IN CASE OF DAMAGE TO ANY PARTS, NOTIFY THE VENDOR AS SOON AS
POSSIBLE.
- IN CASE OF GLASS BREAKAGE (IF THE UNIT HAS A GLASS TABLE TOP OR
PARTS MADE OF GLASS) DO NOT HANDLE THE BROKEN GLASS WITH YOUR
BEAR HANDS, AND CONTACT THE VENDOR IMMEDIATELY. DO NOT ALLOW
CHILDREN NEAR THE BROKEN GLASS.
Loading...