Page 1
TDX4SS
Page 2
Dear Customer,
Please carefully read this manual before using the
dishwasher, it will help you to use and maintain the
dishwasher properly.
Keep it toreferto itat a laterdate.
Pass iton to any subsequent owner of the appliance.
This manual contains sections on safety Instructions,
Operating Instructions, Installation Instructions and
Troubleshooting Tips, etc.
ControlPanel...................................................3
Dishwasher Features............................ ........ ...3.
Fill the Rinse Aid Dispenser................. .............4.
Function of Detergent ........................ ..............5.
Attention before or after loading the Dishwasher
Baskets...................................................... ....7..
Loading the upper Basket............................ .....7..
Loading the Lower Basket....................... ....... 8...
Cutlery Basket........................................... ....9...
Wash Cycle Table...........................................11
Turning on the Appliance................................11
Change the Programme...................... ...........12..
At the End of theWash Cycle...................... .....12.
To review the section on troubleshooting Tips
will help you to solve some common problems
by yourself .
Ifyoucannotsolvethe problemsby yourself,
pleaseask for the help of professional technicians.
The manufacturer, following a policy of constant
development and updating of the product, may
make modifications without giving prior notice.
Filtering System............................... ..............13
Caring for the Dishwasher...............................14
Water Connection...................................... .....16.
Positioning the Appliance.............................. ..........17.
Start of Dishwasher .....................17....................
Before calling for service.................................18
Error codes...................................................19
Technical information.....................................20
Page 3
WARNING!
When using your dishwasher, follow the precautions listed below:
This appliance must be grounded. In the event of a
malfunction or breakdown, grounding will reduce
theriskof anelectricshockbyprovidingapathof
least resistance of electric current. This appliance
is equipped with a cord having an equipmentgrounding conductor and a grounding plug.
The plug must be plugged into an appropriate outlet
that is installed and grounded in accordance with
all local codes and ordinances.
Do not abuse, sit on, or stand on the door or dish
rack of the dishwasher.
Do not touch the heating element during or
immediately after use.
(This instruction is only applicable to machines
with a visual heating element.)
Do not operate your dishwasher unless all
enclosure panels are properly in place.Open
the door very carefully if the dishwasher is
operating, there is a risk of water squirting out.
Do not place any heavy objects on or stand on the
door when it is open. The appliance could tip
forward.
When loading items to be washed:
1)Locate sharpitems sothattheyarenot likely
to damage the door seal;
2) Warning: Knives and other utensilswith
sharp points must be loaded in the basket
withtheir pointsdownor placedin a
horizontal position.
When using your dishwasher, you should
prevent plastic items from coming into contact
with the heating element.(This instruction is only
applicableto machines with a visual heating
element.)
Check that the detergent comparment is empty
after completion of the wash cycle.
Do not wash plastic items unlessthey are marked
dishwasher safe or the equivalent. For plastic items
n
ot so marked, check the manufacturer's
recommendations.
Use only detergent and rinse additives
designed for an automatic dishwasher.
Never use soap, laundry detergent, or hand
washing detergent in your dishwasher. Keep
these products out of the reach of children.
Improper connectionof the equipment-grounding
conductor can result in the risk of an electric shock.
Check with a qualified electrician or service
representative if you are in doubt whether the
appliance is properly grounded. Do not modify the
plug provided with the appliance; If it does not fit
the outlet.Havea proper outlet installed by a
qualified electrician.
Keep children away from detergent and rinse aid, keep
children away from the open door of the dishwasher,
there could still be some detergent left inside.
This appliance is not intended for use by persons
(including children )with reduced physical, sensory or
mental capabilities, or lack of experienceand
knowledge,unless they have been givensupervision
or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do
not play with the appliance.
Dishwasher detergents are strongly alkaline, they
can beextremely dangerous if swallowed. Avoid
contact with skin and eyes and keep children away
from the dishwasher when the door is open.
The door should not be left open,
since this could increase the risk of tripping.
If the supply cord is damaged,it must be replaced
by the manufacturer or its service agent or a
similarly qualified person in order to avoid a
hazard.
Remove the door to the washing compartment when
removing an old dishwasher from service or discarding it.
Please dispose of packing materials properly.
Use the dishwasher only for its intended function.
During installation, the power supply must not
beexcessivelyor dangerouslybent or flattened.
Do not tamper with controls.
The appliance is to be connected to the water
mains using new hose sets and that old hose-sets
should not be reused.
The maximum number of place settings to be
washed is 8.
The maximum permissible inlet water pressure is
1Mpa.
The minimum permissible inlet water pressure is
0.04Mpa.
1
Page 4
Dispose of the dishwasher packaging materialcorrectly.
All packaging materials can be recycled.
Plastic parts are marked with the standard international abbreviations:
PE for polyethylene, e.g. sheet wrapping material
PS for polystyrene, e.g. padding material
POM polyoxymethylene, e.g. plastic clips
PP polypropylene, e.g. Salt filler
ABS Acrylonitrile Butadiene Styrene, e.g. Control Panel .
WARNING!
Packaging material could be dangerous for children!
For disposing of package and the appliance please go to a recycling centre. Therefore cut
off the power supply cable and make the door closing device unusable.
Cardboard packaging is manufactured from recycled paper and should be disposed in the
waste paper collection for recycling.
By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and humanhealth,which couldotherwise becaused
by inappropriate waste handling of this product.
For more detailed information about recycling of this product, please contact your local
cityoffice and yourhousehold wastedisposalservice.
DISPOSAL: Do not dispose this product as unsorted municipal waste. Collection of such
waste separately for special treatment is necessary.
2
Page 5
2
4 5
12
To get the best performance from your dishwasher, read all
operating instructions before using it for the first time.
8
1
1 On/Off Key-press: To turn On/Off the power supply.
2 Power Light : To come on when the ON/OFF Button is
Presseddown.
3 Half washing Button: To select the half washing.
(It means that the lower spray arm does not run, so
you shouldloadtheupperbasketonly
4 Half washing Light : To come on when half washing
5 Rinse Aid Warning Light :To come on when the Rins e aid
dispenser needs to be refilled.
3
).（Option）
(Option).
Front view
6
1
6
6 Door Handle: Pull it to open the door.
7
Program Button: To select washing program when press
the button.
8 Program indicator light: when you select washing
program, the correspond light will display.
9 Start / Reset Button: Press this button to start or pause the
dishwasher, one of the six program lights will blink when
starting.
7
Back View
9
2
3
4
5
Upper Basket
14
Spray Arms
2
3
Lower Basket
Main Filter
5
Detergent Dispenser
6
CupShelf
7
8
9
10
7
Silverware Basket
8
Coarse Filter
9
Rinse Aid Dispenser
3
Drain pipe connector
10
11
Inletpipe connector
11
Page 6
Rinse Aid Dispenser
Therinse aid isreleased during the final rinseto preventwater from forming droplets on your dishes, which can
leave spots and streaks. It also improves drying by allowing water to roll off the dishes. Your dishwasher is
designedto use liquid rinse aids. The rinse aid dispenser is locatedinside the door next to the detergent dispenser.
To fill the dispenser, open the cap and pour the rinse aid int o the dispenser until the level indicator turns completely
black. The volume of the rinse aid container is about 110ml.
Function of Rinse Aid
Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, and spot and streak free drying.
Attention!
Only use branded rinse aid for dishwasher. Never fill the rinse aid dispenser with any othersubstances
(e.g. Dishwasher cleaning agent, liquid detergent). This would damage the appliance.
When to Refill the Rinse Aid Dispenser
If thereis no rinse-aid warninglight in the control panel, you can judge the amount of rinse-aid by the color of the optical level
indicator "D" located next to the cap. When the rinse-aid container is full, the whole indicator will be dark .As the rinse-aid
diminishes, the size of the dark dot decreases. You should never let the rinse aid get below 1 / 4 full.
As the rinse aid diminishes, the size of the black dot
on the rinse aid level indicatorchanges, as illustrated below.
Full
3/4full
1/2full
1 / 4 full - Should refill to eliminate spotting
Empty
RINSE AID DISPENSER
To open the dispenser, turn the cap to the "open" (left) arrow and lift it out.
1
Pour the rinse aid into the dispenser, being careful not to overfill.
2
Replace the cap by inserting it aligned with "open" arrow and turning it to the closed (right) arrow.
3
Be careful not to overfill the dispenser, because this could cause over sudsing. Wipe away any spills
with a damp cloth. Don't forget to replace the cap before you close dishwasher door.
Attention!
Clean up any rinse aid split during filling with an absorbent cloth to avoid excess foaming
during the next wash.
4
Page 7
Adjusting Rinse Aid Dispenser
The rinse aid dispenser has six scales. Always start with the dispenser set on "4".
If spots and poor drying are a problem, increase the amount of rinse aid dispensed
by removing the dispenser lid and rotating the dial to "5". If the dishes still are not
drying properly or areshow spots,adjust the dial to the next higherlever until your
dishes are spot-free. The recommended setting is "4". (Factory value is "4".)
NOTE:
Increasethe dose if there are drops of water or lime spots on the dishes after washing.
Reduce it if there are stickywhitish stains on your dishes or a bluish film onglasswareor
knife blades.
Detergents with its chemical ingredients are necessary to removedirt, crushdirtandtransportitoutofthedishwasher.
Most of the commercial quality detergents are suitable for this purpose.
Concentrated Detergent
Based on their chemical composition, detergents can be split in two basic types:
conventional, alkaline detergents with caustic components
low alkaline concentrated detergents with natural enzymes
The use of“normal” washingprograms in combination with concentrated detergents
reduces pollution and is good for your dishes; these wash programs are specifically matched
to the dirt-dissolving properties of the enzymes of the concentrated detergent. For this reason
“normal”wash programs in which concentrated detergents are used can achieve the same
results that can otherwiseonly be achievedusing “intensive”programs.
Detergent Tablets
Detergent tablets of different brands dissolve at different speeds. For this reason some
detergent tablets cannot dissolve and develop their full cleaning power during short
programs. Therefore please use long programs when using detergent tablets, to
ensure the complete removal of detergent residuals.
Detergent Dispenser
The dispenser must be refilled before the start of each wash cycle following the instructions
provided in the wash cycle table . Your dishwasher uses less detergent and rinse aid than
Conventional dishwasher. Generally, only one tablespoon of detergent is needed for
a normal wash load. More heavily soiled items need more detergent. Always add the
detergent just before startingthe dishwasher, otherwise it could get dampandwillnot
dissolveproperly.
Amount of Detergent to Use
If the lid is closed: press release button. The lid will spring open.
Always add the detergent just before starting each wash cycle.
Only use branded detergent aid for dishwasher.
WARNING!
Proper Use of Detergent
Use only detergent specifically made for the use in dishwashers. Keep your detergentfresh and dry.
Don't put powdered detergent into the dispenser until you're ready to wash dishes.
Dishwasher detergent is corrosive! Take care to keep it out of reach of children.
5
Page 8
Fill in detergent
Fill the detergent dispenser with detergent.
The marking indicates the dosing levels , as
illustrated on the right:
The place of main wash cycle detergent placed ,
A
“MIN”means approximately 20g of detergent.
The place of pre-wash cycle detergent placed ,
B
approxim ately 5g of detergent
Please observe the manufacturers dosing and storage
recommendations as stated on the detergent packaging.
Close the lid and press until it locks in place.
If the dishes areheavily soiled, place an additional detergent dose in the pre-wash detergent
chamber. This detergent will take effect during the pre-wash phase.
NOTE:
You find information about the amount of detergent for the single programmes on the
last page. Please aware, that according to the level soiling and the specific hardness of
water differences are possible.
Please observe the manufacturer's recommendations on the detergent packaging.
Detergents
There are 3 sorts of detergents
1.With phosphate and with chlorine
2.With phosphate and withoutchlorine
3.Without phosphate and without chlorine
Normally new pulverised detergent iswithout phosphate.Thus the water softener function of
phosphate is not given. In this case we recommend to fill salt in the salt container even when
the hardness of water is only 6 °dH. If detergents without phosphate are used in the case of hard water
often white spots appear on dishes and glasses. In this case please add more detergent to reach
better results. Detergents without chlorine do only bleach a little. Strong and coloured spots will not
be removed completely. In this case please choose a program with a higher temperature.
Attention
Keep all detergents in a safe place out of children's reach.
Always add the detergent in the dispenser just before starting the dishwasher.
6
Page 9
For best performance of the dishwasher, follow these loading guidelines. Features and
appearance of baskets and cutlery baskets may vary from your model.
Attention before or after Loading the Dishwasher Baskets
Scrape off any large amounts of leftover food. Soften remnants of burnt foodinpans.
It is not necessary to rinse the dishes under running water.
Place objects in the dishwasher in following way:
1.Items suchas cups, glasses, pots/pans, etc. are faced downwards.
2.Curved items, or ones with recesses, should be loaded aslant so that water can run off.
3.All utensilsare stacked securely and can not tip over.
4.All utensilsare placed in the way that the spray arms can rotate freely during washing.
Very small items should not be washed in the dishwasher as they could easily fall out of the baskets.
Removing the Dishes
To prevent water dripping from the upper basket into the lower back, we recommend that you
empty the lower basket first and then the upper basket.
Loading the Upper Basket
The upper basket is designed to hold more delicate and lighter dishware such as glasses,coffee
and tea cup and saucers, as well as plates, small bowls and shallow pans (as long as they are
not too dirty).
Position the dishes and cookware so that they do not get moved by the spray of water.
1
2
1
2
1
3
1
2
3
Cups
Glasses
Saucers
2
Adjusting the Upper Basket
The height of the upper basket can be adjusted in order to create more space for large utensils
both for the upper/lower basket. The height of the upper basket can be adjusted by placi ng the
wheels on different height of the rails. Long items, serving cutlery, salad servers and knives
should be placed on the shelf so that they do not obstruct the rotation of the spray arms.
The shelf can be folded back or be removed when not required for use.
7
Page 10
Loading the Lower Basket
We recommend that you place large items which are most difficult to clean into the low er basket:
pots, pans, lids, serving dishes and bowls, as shown in the figure to the right.
It is preferable to place serving dishes and lids on the side of the racks in order to avoid blocking
therotationofthe top spray arm.
Pots, serving bowls, etc. must alwaysbe placed topdown.
Deep pots shouldbe slanted to allow water to flow out.
Thebottom basket featurefold downtinerows so thatlargeror morepotsand pans can be loaded.
6
4
5
5
7
Folding spikes
Forbetter stacking ofpotsand pans, thespikes can be folded down as
show in the pic ture right.
Dinner plates
4
Soup plates
5
Dessert dishes
6
Silverware basket
7
8
Page 11
Cutlery Basket
Cutlery should be placed in the cutlery basket with the handles at the bottom. If the rack has side baskets, the
spoons should be loaded separately into the appropriate slots, especially long utensils should be placed in the
horizontal position at the front of the upper basket as shown in the picture.
4
1
1
1
1
1
1
1
1
3
3
3
3
Do not let any item extend through the bottom.
Always load sharp utensils with the sharp point down!
225
4
4
5
4
5
2
4
4
5
2
4
5
2
4
5
3
2
2
5
3
Forks
1
2
Soup spoons
3
Dessert spoons
Teaspoons
4
5
Knife
3
3
2
5
Do not let any item extend through bottom.
For washing in the dishwasher the following cutlery/dishes
Are not suitable
Cutlery with wooden, horn china or
mother-of-pearl handles
Plastic items that are not heat resistant
Older cutlery with glued parts that are not
temperature resistant
Bonded cutlery items or dishes
Pewter or cooper items
Crystal glass
Steel items subject to rusting
Wooden platters
Items made from synthetic fibres
NOTE:
Do not put in items that are dirty of cigarette ash, candle wax, lacquer or paint.
If you buy new dishes please make sure that they are suitable for dishwashers.
NOTE:
Please do not overload your dishwasher. Do not use dish that is not suitable for dishwashers.
This is important for good results and for reasonable energy consume.
Loading cutlery and dishes
Are of limited suitability
Some types of glasses can become
dull afte r a large number of washes
Silver and aluminum parts have a
tendency to discolour during washing
Glazed patterns may fade if machine
washed frequently
Beforeloading the dishes,you should:
Remove large left-over
Soften remnants of burnt food in pans
When loading the dishes and cutlery, please note:
Dishes and cutlery must not impede the rotation of the spray arms
Load hollow items such as cups, glasses, pans etc. with the opening downwards so that
water cannotcollectin the containeror adeepbase
9
Page 12
Di
shes and items of cutlery must not lie inside one another, or cover each othe r
To
avoid damage to glasses, they must not touch
Load large items which are most difficult to clean into the lower rack
T
he upper rack is designed to hold more delicateand lighter dishware such as glasses, coffee
and tea cups
Attention!
Long bladed knives stored in an upright positionare a potential hazard!
Long and/or sharp items of cutl ery such as carving knives must be positioned
horizontally inthe upper basket.
Damage to glassware and other dishes
Possible causes:
Type of glass or manufacturing process. Chemical composition of detergent.
Water temperature and duration of dishwasher programme.
Suggested remedy:
Use glassware or porcelain dishes that have been markeddishwasher-proof by the
manufacturer
Use a mild detergent that is described as kind of dishes If necessary, seek further
information from detergent manufacturers.
Select a program me with as low a temperat ure.
To prev ent damage, take glass and cutlery out of the dishwasher as soon as po ssible
after the programme has ended.
10
Page 13
Intensive
For the heaviest soiled loads,
such as pots,pans,casserole
dishes and dishes that have
been sitting with dried food
on them for a while.
Pre-wash
-wash( 0℃
Pre 5 )
Wash (60 ℃)
Rinse (70 ℃)
Drying
4/20 g.
160
1.10
12.9
Heavy
Normal
(AS/NZS 200 7.1 )
Rinse
Rapid
Soak
For normally soiled loads,
such as , plates,glasses
and lightlysoiled pans.
standard daily cycle.
For lightly soiled loads,such
as plates,glasses,bowls and
lightly soiled pans.
For dishes that need to be
rinsed and dried only.
For lightly soiled loads, such
as glasses, crystal and fine
china.
Ashorterwashforlightly
soiled loads that do not
need drying.
pots
Pre-wash
Pre-wash
Wash (50 ℃)
Rinse (65 ℃)
Drying
Pre-wash
Wash (45 ℃)
Rinse (60 ℃)
Drying
Wash(45 )
Rinse (70 ℃)
Drying
Pre-wash
wash(40 )
rinse(70 )
drying
Wash (40 ℃)
Rinse (45 ℃)
℃
℃
℃
4/20 g.
20 g.
15 g.
15 g.
155
105
85
110 10.20.75
30
0.74
0.65
0.75
0.35
12.9
10.2
7.5
6.5
Turning on the Appliance
Starting a wash cycle...
1
Draw out the lower and upper basket, load the dishes and
push them back. It is commended that loading the lower
basket first, than the upper one (see the section entitled
“Loading the Dishwasher”).
2
Pour in the detergent (see the section entitled “Salt,
Detergent and Rinse Aid”).
3
Insert the plug into the socket. The power supply is 220-240
VAC 50 HZ, the specification of the socket is 10 A 250 VAC.
Make sure that the water supply is turned on to full pressure.
When select 6 kinds of wash program
4
Press the programme button, the wash program will change as follows direction
Strong->Normal->Eco->Rinse->Glass->Rapid;
When a program is selected, the response light will light. Then press the
Start/Reset button, the program is running and the light becomes blinking..
11
Page 14
5
If you want to select half washing, you should press Half washing
button after selecting washing program, and the half washing light
will be on, then press the Start/Reset button to start.
Note
: When you press the Start/Reset button to pause during washing,
the program light will stop blinking and the dishwasher will mooing
every minute unless you press the Start/Reset button to start.
Premise
has been running for a short time. Otherwise, the detergent may have
already been released, and the appliance may have already drained the
wash water. If this is the case, the detergent dispenser must be refilled
(see the section entitled " Loading the Detergent " ).
Press Start/Reset Button more than three seconds the machine will be
in stand by state , then you can change the program to the desired
cycle setting (see the section entitled " Starting a wash cycle. . . " ).
NOTE: If you open the door when washing, the machine will pause,
the program light will stop blinking and the buzzer will mooing every
minute unless you close the door. After you close the
machine will keep on working after 10 seconds.
The program lights shows the state of the dishwasher:
a) A --> stand by
ll of the program lights cut of f
b) One of the program lights on --> pause
c) One of the program lights blinking slowly --> run
d
)some of the up three program lights fast blinking -->error
You can modified the washing program, just the dishwasher:
door , the
A forgotten dish can be added at any time before the detergent cup opens.
Open the door a little to stop the washing.
1
After the spray arms stop working, you can open the door
2
completely.
It is dangerous to open the door when washing,because the hot water may scaldyou.
When the working cycle has finished, the buzzer of the dishwasher will soun d for 8 seconds, then stop. Turn off
the appliance using the ON/OFF button, shut off the water supply and open the door of the dishwasher.
Wait for a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they
are still hot and moresusceptible to breakage. They will also dry better.
12
Load the forgotten dishes.
3
Close the door, the dishwasher will start running again
4
after 10 seconds.
Page 15
Switch Off the Dishwasher
The program light is on but isn't blinking, only in this case the programme has ended.
1.Switch off the dishwasher by pressing the ON/OFF button.
2.Turn off the water tap!
Open the door carefully.
Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down around 15 minutes
before removing from the appliance.
Open the dishwasher's door, leave it ajar and wait a few minutes before removing the dishes. In this way they
will be cooler and the drying will be improved.
It is normal that the dishwasher is wet inside.
Empty the lower basket first and then the upper one. This will avoid water dripping from the upper Basket onto
the dishes in the lower one.
The filter prevents larger remnants of food or other objects from getting inside the pump.
The residues may block the filter,in this case they must be removed.
The filter system consists of a coarse filter, a flat (Main filter)
And a microfilter (Fine filter).
Main filter
2
1
3
- Inspect the filters for blocking after every time the dishwasher has been used.
- By unscrewing the coarse filter. you can remove the filter system. Remove any food remnants and clean the
filters under running water.
Food and soil particles trapped in this filter are pulverized by a
special jet on the lower spray arm and washed down the
drain.
Coarse filter
Larger items, such as pieces of bones or glass, that could clog
the drain are trapped in the coarse filter. To remove an item
caught in this filter, gently squeeze the taps on the top of this
filter and lift it out.
Fine filter
This filter holds soil and food residues in the sump area and
prevents it from being redeposit on the dishes during a cycle.
1
2
3
NOTE：
When following this procedure from step1 to step 3, the filter system will beremoved;
whenfollowingitfromStep3toStep1,thefiltersystemwillbeinstalled.
13
Page 16
Filter assembly
For best performance and results, the filter assembly must be cleaned. The filter efficiently removes food
particles from the wash water, allowing it to be recycled during the cycle. For best performance and results,
the filter must be cleaned regularly. For this reason, it is a good idea to remove the larger food particles
trapped in the filter after each wash cycle by rinsing the semicircular filter and cup under running water.
To remove the filter device, pull the cup handle in the upward direction. The entire filterassembly should be
cleanedonce a week.
To clean the coarse filter and the fine filter, use a cleaning brush. Then, reassemblethe filter
parts as shown in the figures left and reinsert the entire assembly in the dishwasher, positioning
in its seat and pressing downward.
The dishwasher must never be used without the filters. Improper replacement of the filter may
reduce the performance level of the appliance and damage dishes and utensils.
The dishwasher must never be used without the filters.
Improper replacement of the filter may reduce the performance level of the appliance and
damage dishes and utensils.
Cleaning the Spray Arms
To removethe upper spray arm, screw off the nut clockwise then remove
the arm.
Caring for the Dishwasher
The control panel can be cleaned by using a lightly dampened cloth.
Aftercleaning, makesure to dryitthoroughly.
For the exterior, use a good appliance polish wax.
Neveruse sharp objects, scouringpads or harshcleaners on any part of the dishwasher.
14
Page 17
To clean the edge around the door, you should use only a soft warm, damp cloth.
To avoidpenetration of water into the door lock and electrical components,donot
use a spray cleaner of any kind.
Never use a spray cleaner to clean the door panel as it may damage the door lock and electrical components.
Abrasive agents or some paper towels should not be used because of the risk of scratching or leaving spots
on the stainless steel surface.
After every wash, turn off the water supply to the
appliance and l eave the d oor slightly ajar so that
moisture and odours are not trapped inside.
Before cleaning or performing maintenance, always
removethe plug from the socket. Do not run risks.
To clean the exterio r and rubber parts of the dishwasher,
do not use solvents or abrasive cleaning products.
Rather,useonlya cloth and warm soapywater.
To remove spotsor stains fromthe surface of the
interior, use a cloth dampened withwater and a little
vinegar, or a cleaning product made specifically for
dishwashers.
For personal safety:
WARNING!
DO NOT USEAN EXTENSION CORD OR AN ADAPTERPLUG WITH THIS APPLIANCE.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE EARTHING
CONNECTION FROM THE POWER CORD.
When you go on holiday, it is recommend that you run a
wash cyc le with the dishwasher empty and then remove
the plugfrom the socket, turn off the water supplyand
leave the door of the appliance slightly ajar. This will help
the seals to last longer and prevent odours from forming
withinthe appliance.
If the appliance must be moved, try to keep it in the vertical
position. If absolutely necessary, it can be positionedon
its back.
One of the factors that cause odours to form in the
dishwasher is food that remainstrapped in the seals.
Periodic cleaning with a damp sponge will prevent this
from occurring.
Please look at the rating label to know the rating voltage and connect the dishwasher to the appropriate power supply.
Use the required fuse 10 amp, time delay fuse or circuit breaker recommended and provide separate circuit serving
only this appliance.
Ensure the voltage and frequency of the power being corresponds to
those on the rating plate. Only insert the plug into an electrical socket which is earthed
properly. If the electrical socket to which the appliancemust be connectedisnot
appropriate for the plug , replace the socket, rather than using a adaptors or th e like as
they could cause overheating and burns.
This appliance must be earthed. In the eventof a malfunction or breakdown, earthing will reduce the risk of
electric shock byproviding a path of least resistance for the electric current. This appliance is equipped with a
cord having an equipment-earthing conductor and an earthing plug. The plugmustbepluggedintoan
appropriate outlet that is installed and earthed in accordance with all local standards and requirements.
15
Page 18
WARNING!
Improper connection of the equipment earthing conductor can result in the risk of an
electric shock.
Check with a qualified electricianor service representative if you are in doubt whether the
appliance is properly earthed.
Do not modify the plug provided with the appliance. If the plug does not fit properly to the
outlet, please have a qualified electrician to install a proper outlet.
for personal safety:
DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE.
DO NOT, UNDER ANY CIRCUMST ANC ES, CUT OR REMOVE THE
CONNECTION
Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure
that it is fastened tightly in place.
If the water pipes are new or have not been used for an extended period of time,letthe
water run to make sure that the water is clear. This precaution is needed to avoid the
risk of the water inlet to be blocked and damage the appliance.
The water supply to the appliance can also be connected to t he household hot water
line (suchas, central system, heating system),as long as it does not exceeda
temperature of 60 C. In this case, the wash cycle time will be shortened by about 15
minutes and the wash efficiency slightly reduced.
The connection must be made to the hot water line following the same procedures as
described in the section for the connection to the cold water line.
FROM THE POWER CORD.
EARTHING
WARNING!
Insertthe drain hoseintoa drain pipe with a minimum diameter of 4 cm, or let it run into the sink, making sure to
avoid bending or crimping. Use the special plastic support tha t comes with the appliance. The top of the hose
must be at a height between 40 and 100cm.The free end of the hose must not be im mersed in water.
In order to avoid that there is more water staying in the inlet hose, please close
the hydrant after using.(Not applicable to appliances without aqua-stop.)
PLEASEHANG UPTHEDRAIN HOSE EITHER WAYOFA, B, C
Close the drain hose hook to the counte r
Front
Drain hose hook
Counter
A
B
Drain pipe
16
C
φ
40mm
Page 19
Position the appliance in the desiredlocation. The back should rest against the wall behind it, and the sides,
along the adjacent cabinets or walls. The dishwasher is equipped with water supplyand drain hoses that can
be positioned either to the right or the left sides to facilitate proper installation.
Once the appliance is positioned for levelling, the height of the dishwasher
may be altered via adjustment of the screwing level of the feet. In any case,
the appliance should not be inclined more than 2 .
Water Outlet
Connect the water drain hose. The drain hose must be correctly fitted to avoid water leaks.
Ensure that the water drain hose is not kinked or squashed.
Extension Hose
If you need a drain hose extension, make sure touse a similar drain hose.
It must be no longer than 4 metres; otherwise the cleaning effect of the dishwasher could be reduced.
Syphon Connection
The waste connection must be at a height of between 40 cm (minimum) and 100 cm (maximum)
from the bottom of the dish . The water drain hose should be fixed by a hose clip.Thefreeendof
the hose must not be immersed in water.
The following things should be checked before starting the dishwasher.
1 The dishwasher is level and fixed properly
2 Theinletvalveisopen
3 There is a leakage at the connections of the conducts
4 The wires are tightly connected
5 The power is switched on
6 The inlet and drain hoses are knotted
7 All packing materials and printings should be taken out from the dishwasher
After installation, please make sure to keep this manual.
The content of this manual is very helpful to the users.
17
Page 20
Fuse blown,or the
circuit breaker acted
Replace fuse or reset circuit breaker. Remove any other
appliances sharing the same circuit with the dishwasher
Technical
problems
Power supply is not
turned on
Error code:E1;
Waterpressureislow
Door of dishwasher
notproperlyclosed.
Kink in drain hose
Filter clogged
Kitchen sink clogged
Improper detergent
Spilled rinse-aid
Make sure the dishwasher is turned on and the door is
closed securely.
Make sure the power cord is properly plugged into the
wall socket.
Check that the water supply is connected properly and
the water is turned on.
Make sure to close the door properly and latch it.
Check drain hose.
Check coarse the filter
(see section titled " Cleaning The Filter ")
Check the kitchen sink to make sure it is draining well.
If the problem is the kitchen sink not draining ,you may
need a plumber rather than a serviceman for dishwashers.
Use only the special dishwasher detergent to avoid
suds. If this occurs, open the dishwasher and let suds
evaporate. Add 1 gallon of cold water to the tub. Close
and latch the dishwasher, then Start the "soak" wash
cycle to drain out the water . Repeat if necessary.
Always wipe up rinse-aid spills immediately.
General
problems
Noise
Detergent with
colour ant w as used
Hard water minerals
The affected items are
notcorrosion resistant.
Aprogrammewasnot
run after dishwasher
salt was added.
Traces of salt have
gotten into the wash cycle.
Thelidofthesofter
is loose
Asprayarmis
knockingagainst
an item in a basket
Items of crockery
areloose in the
washcabinet
This may be caused
by on-site installation
or the cross-section of
the piping.
Make sure that the detergent is the one without
colourant.
To clean the interior, use a damp sponge with
dishwasher detergentandwearrubber gloves.
Never use any other cleanerthan dishwasher
detergent for the risk of foaming or suds.
Always runthe quick wash programme .
without any crockery in the dishwasher and
withoutselecting the Turbofunction (if present),
after adding dishwasher salt.
Check the lip .Ensure the fix is fine.
Interrupt the programme, and rearr ange the items
which are obstructing the spray arm.
Interrupt the programme,
and rearrange the items of crockery.
This has no influence on the dishwasher function.
if in doubt, contact a suitably qualified plumber.
18
Page 21
Thedishes were not
loaded correctly.
See notes in " Loading the Dishwasher Baskets ".
Unsatis
-factory
washing
result
Theprogramme was
not powerful enough.
Not enough detergent
was di spensed.
Items are blocking
the path of spray arms.
The filter combination
in the base of wash
cabinet is not clean or
is not correctly fitted.
This may cause
the spray arm jets
to get blocked.
Combination of soft
water and too much
detergent.
Aluminum utensils
have rubbedagainst
dishes.
Dishes block
detergentcups.
Improper loading
Too little rinse-aid
Select a more intensive programme.
See" Wash Cycle Table ".
Use more detergent, or change your detergent.
Rearrange the items so that the spray can rotate freely.
Clean and/or fit the filter combination correctly.
Clean the spray arm jets.See "Cleaning the Spray
Arms".
Use less detergent if you have soft water and select
a shortest cycle to wash the glassware and to get
them clean.
Use a mild abrasive cleaner to eliminate those marks.
Re-loading the dishes properly.
Load the dishwasher as suggested in the directions.
Increase the amount of rinse-aid/refill the rinse-aid
dispenser.
Unsatis
-factory
drying
result
Dishes are removed
too soon
Wrong program
has been selected
Useof cutlery with
alow-qualitycoating
Longer inlet time.
Longer heating time,
but not reaching required temperature
Water leakage.
Failure of temperature sensor
Do not empty your dishwasher immediately after
washing. Open the door slightly so that the steam can
escape. Begin unloading the dishwasher only once t
he dishes are barely warm to the touch. Empty the low
basket first. This prevents water form dropping off
dishes in the upper basket.
In short program the washing temperature is lower.
This also lowers cleaning performance. Choose
a program with a long washing time.
Water drainage is more difficult with these items.
Cutlery or dishes of this type are not suitable for
washing in the dishwasher.
Faucets is not opened, or water intake is restricted,or water pressure
is too low.
Malfunction of temperature sensor or of heating element.
Break of onnection ducts.
Open circuit or break of temperature sensor
WARNING!
Failure of temperature sensor
Short circuit or break of temperature sensor
If overflow occurs, turn off the main water supply before calling a service.
If there is water in the base pan because of an overfill or small leak,
the water should be removed before restarting the dishwasher.
19
Page 22
Height : 850mm
Width : 450mm
Depth : 580mm
Voltage connected Load : see rating label
Water pressure: 0.04-1.0MPa
Hot water connection : max 60 ℃
Power supply: see rating label
Capacity: 8 Place settings
20
Loading...