Technics PV-D4754S User Manual

Download

DVD/VCR DECK

Operating Instructions

(Connection)

Initial Setup

Model No.

PV-D4754S

Connections and Initial Setup Procedures are on pages 12 to 17.

Operation

Basic

Operation

VCR

Operation

DVD

Information

For Your

MULTI FORMAT PLAYBACK

Ability to play back may depend on recording conditions.

As an ENERGYSTAR Partner, Matsushita Electric Corporation of America has determined that this product or product model meets the ENERGYSTAR guidelines for energy efficiency.

Please read these instructions carefully before attempting to connect, operate or adjust this product. Please save this manual. Spanish Quick Use Guide is included. (Guía para rápida consulta en español está incluida.)

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

LSQT0797 A

Important Safeguards and Precautions

TO REDUCE THE RISK OF ELECTRIC SHOCK, FIRE, INJURY TO PERSONS OR DAMAGE TO THIS PRODUCT, READ AND RETAIN ALL SAFETY AND OPERATING INSTRUCTIONS. HEED ALL WARNINGS IN THE MANUAL AND ON THE PRODUCT.

INSTALLATION

1 POWER SOURCE CAUTION

Operate only from a power source indicated on the unit or in this manual. If necessary, have your Electric Utility Service Company or Video Products Dealer verify the power source in your home.

2 POLARIZED OR GROUNDING PLUG

As a safety feature, this product comes with either a polarized power cord plug (one blade is wider than the other), or a three-

wire grounding type plug. POLARIZED PLUG CAUTION: This plug will only fit into an outlet one way. If you cannot fully insert the plug, try reversing it. If it still will not fit, have an electrician install the proper wall outlet. Do not defeat the safety feature by tampering with the plug. GROUNDING PLUG CAUTION: This plug will only fit into a three-hole grounding outlet. If necessary, have an electrician install the proper outlet. Do not defeat the safety feature by tampering with the plug.

3 POWER CORD

Make sure power cords are routed so that they are not likely to

have anything rest on them, roll over them, or be in the way of

walking traffic. If an extension cord is used, make sure it also

has either a polarized or grounded plug and that the cords can

be securely connected. Frayed cords, damaged plugs, and

damaged or cracked wire insulation are hazardous and should

be replaced by a qualified service technician.

Overloaded outlets and extension cords are fire hazards and

should be avoided.

4 DO NOT BLOCK VENTILATION HOLES

Ventilation openings in the cabinet release heat generated during

operation. If they are blocked, heat build-up inside the unit can

cause failures that may result in a fire hazard or heat damage to

cassettes or discs.

For protection, follow these rules:

a. Never cover ventilation slots or the unit while in use, or

operate the unit when placed on a bed, sofa, rug, or other soft surface.

b. Avoid built-in installation, such as a book case or rack,

unless proper ventilation is provided.

5 PLACEMENT: AVOID EXTREMELY HOT LOCATIONS OR

SUDDEN TEMPERATURE CHANGES

Do not place the unit over or near heater or radiator, in direct

sunlight, inside closed vehicles, in high temperature [over 104°F

(40°C)], or in over 75% humidity. If the unit is suddenly moved

from a cold place to a warm one, moisture may condense in the

unit and on the tape causing damage. Never subject the unit to

vibration, impact, or place it so that the surface is tilted as

internal parts may be seriously damaged.

6 TO AVOID PERSONAL INJURY

• Do not place unsecured equipment on a sloping surface.

• Do not place this unit on any support that is not firm, level, and adequately strong. The unit could fall causing serious injury to a child or adult and damage to the unit.

• An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

• Carefully follow all operating instructions and use the manufacturer's recommended accessories when operating this unit or connecting it to any other equipment.

1 SAFE ANTENNA AND CABLE CONNECTION

If an outside antenna or cable system is connected to the equipment, be sure the antenna or cable system is grounded so as to provide some protection against built up static charges and voltage surges. Section 810 of the National Electrical Code, ANSI/NFPA 70 (in Canada, part 1 of the Canadian Electrical Code) provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode.

2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES OR

CIRCUITS

An outside antenna system should be located well away from power lines, electric light or power circuits and where it will never come into contact with these power sources if it should happen to fall. When installing an outside antenna, extreme care should be taken to avoid touching power lines, circuits or other power sources as this could be fatal. Because of the hazards involved, antenna installation should be left to a professional.

If the unit has been in storage or moved to a new location, refer first to the INSTALLATION section of these safeguards.

1 KEEP THE UNIT AWAY FROM WATER OR MOISTURE OF ANY KIND. 2 IF EQUIPMENT IS EXPOSED TO RAIN, MOISTURE, OR STRONG

IMPACT, unplug the unit and have it inspected by a qualified service technician

before use.

3 DURING AN ELECTRICAL STORM

During a lightning storm, whether indoors or outdoors, or before leaving the unit unused for extended periods of time, disconnect all equipment from the power source as well as the antenna and cable system.

4 WHEN THE UNIT IS PLUGGED IN

• Never expose the unit to rain or water. DO NOT OPERATE if liquid has been spilled into the unit. Immediately unplug the unit, and have it inspected by a service technician. Fire and shock hazards can result from electrical shorts caused by liquid contact inside.

• Never drop or push any object through openings in the unit. Some internal parts carry hazardous voltages and contact can cause electric shock or fire hazard. Do not put any foreign object on the disc tray.

• Avoid placing the unit directly above or below your TV set as this may cause electrical interference. Keep all magnets away from electronic equipment.

5 USING ACCESSORIES

Use only accessories recommended by the manufacturer to avoid risk of fire, shock, or other hazards.

6 CLEANING THE UNIT

Unplug the unit. Then, use a clean, dry, chemically untreated cloth to gently remove dust or debris. DO NOT USE cleaning fluids, aerosols, or forced air that could over-spray, or seep into the unit and cause electrical shock. Any substance such as wax, adhesive tape, etc. may mar the cabinet surface. Exposure to greasy, humid, or dusty areas may adversely affect internal parts.

1 DO NOT SERVICE THIS PRODUCT YOURSELF

If, after carefully following the detailed operating instructions, this product does not operate properly, do not attempt to open or remove covers, or make any adjustments not described in the manual. Unplug the unit and contact a qualified service technician.

2 IF REPLACEMENT PARTS ARE REQUIRED

Make sure the service technician uses only parts specified by the manufacturer, or those having the same safety characteristics as the original parts. The use of unauthorized substitutes may result in fire, electric shock, or other hazards.

3 HAVE THE SERVICE TECHNICIAN PERFORM A SAFETY CHECK

After any service or repairs to the unit, request the service technician to conduct a thorough safety check as described in the manufacturer’s service literature to ensure that the unit is in safe operating condition.

OUTDOOR ANTENNA INSTALLATION

NEC - NATIONAL

ELECTRICAL CODE

ELECTRIC SERVICE EQUIPMENT

USING THE UNIT

SERVICE

GROUND CLAMP

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

Safety Precautions/Mesures de sécurité

To prevent fire or shock hazard, do not expose this equipment to rain or moisture.

To prevent electric shock, match wide blade of plug to wide slot, fully insert.

AVERTISSEMENT:

Afin de prévenir tout risque d’incendie ou de chocs électriques, ne pas exposer cet appareil à la pluie ou à une humidité excessive.

ATTENTION:

Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu’au fond.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any inside part of this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.

CAUTION:

UNIT IS A CLASS I LASER PRODUCT. HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE UNIT CORRECTLY AS INSTRUCTED.

WHEN THIS UNIT IS PLUGGED TO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT ATTEMPT TO REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

CAUTION:

LASER RADIATION WHEN OPEN DO NOT STARE INTO BEAM.

ATTENTION:

RAYONNEMENT LASER EN CAS D’OUVERTURE. NE PAS REGARDER DANS LE FAISCEAU.

(Inside of product)

FCC NOTE:

This equipment has been tested and found to comply with part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when operated in a residential environment. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, use the equipment in another location and/or utilize an electrical outlet different from that used by the receiver. If necessary, consult the dealer or an experienced radio/TV technician for help. The user may find the booklet, “Something About Interference” available from FCC local regional offices helpful.

FCC Caution:

To assure continued compliance, (example- use only shielded interface cables when connecting to other devices.) Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Region Management Information:

This DECK is designed and manufactured to respond to the Region Management Information that is recorded on a DVD disc. If the Region number described on the DVD disc does not correspond to the Region number of this DECK, this DECK cannot play this disc.

● The Region number for this DECK is “1”.

● The Player will play DVD-Video marked with labels

containing “1” or “ALL”.

Example:

ALL

Before Using

Congratulations

on your purchase of one of the most sophisticated and reliable products on the market today. Used properly, it will bring you years of enjoyment. Please fill in the information below. The serial number is on the tag located on the back of your DECK.

• Date of Purchase

• Dealer Purchased From

• Dealer Address

• Dealer Phone No.

• Model No.

• Serial No.

Accessories

Remote Control

EUR7724KB0

Loading the Batteries

Battery replacement caution

• Do not mix old and new batteries.

• Do not mix alkaline with manganese batteries.

Record/ Playback Time

Only use tapes with the mark in this DECK.

Tape Speed

Setting

(Standard Play)

SLP

(Super Long Play)

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

PV-D4754S

Batteries 2 “AA”

RF Coaxial Cable LSJA0418

To order accessories, call toll free 1-800-332-5368.

1) Open cover.

2) Insert batteries as marked.

3) Close cover.

Type of Video Cassette

2 Hours

6 Hours 8 Hours

2 Hours

40 Minutes

T180T160T120

3 Hours

9 Hours

Head Cleaning

Playing older or damaged tapes may eventually cause video heads to become clogged.

Video Head Clog Sensor

During playback, this screen appears if clogging is detected. To remove screen, press PLAY on the remote or DECK.

VID

EO HEADSMAY

EED

CLEANING PLEASE I CLEANING OR

REFER

END :PL

NSERT HEAD

CASSETTE

TOMANUAL

• Use “dry” type head cleaning cassette only.

(Part No. NV-TCL30PT is recommended.)

• Follow cleaning tape instructions carefully. Excessive use of tape can shorten head life.

• If head clog symptoms persist, contact your nearest servicenter by visiting our Web Site (see p. 61).

Cleaning DECK

Use a soft cloth or dusting attachment of a vacuum cleaner to remove dust from the ventilation holes on the back sides and bottom of the cabinet. Plastic surfaces are easily scratched and can be marred by alcohol and various solvents. Avoid excessive use of oil-based furniture polishes since the materials used in the cabinet will accumulate more dust. We recommend using a non-abrasive, antistatic cleaner and polisher.

Features for a Quality Picture (VCR)

Digital Auto Picture

Automatically controls the video output signal for less noise depending on the tape condition.

Digital Auto Tracking

Continuously analyzes the signal and adjusts for optimum picture quality.

Manual Tracking Control (to reduce picture noise)

Use during Playback and Slow Motion mode to reduce picture noise. Press CH (TRACKING) / on the remote control or on DECK until the picture clears up. To return to Auto Tracking, press POWER off, then on again a few seconds later.

V-Lock Control (to reduce picture jitter)

In Still mode, CH (TRACKING) / operate as a V-Lock control.

Initial Setup (Connection)

DVD / VCR

Important Safeguards and Precautions ......................... 2, 3

Before Using ......................................................................... 4

DECK & Cassette Information ........................................ 6 , 7

Location of Controls .................................................... 8 ~ 10

Displays (On Screen Displays and Multi Function Display) ................. 11

Connections ............................................................... 12 ~ 15

Initial Setup for Basic Connections (Ready to Play) ....... 16, 17

Basic Operation

VCR

Reset Language, Channels, Clock, VCR’s Output Channel .. 18, 19

Playback/ Record on a Tape........................................ 20, 21

DVD

Basic DVD Operation ................................................... 22, 23

VCR Operation

Timer Recording ........................................................... 24, 25

MTS Broadcast/ VHS Hi-Fi Stereo System ................. 26, 27

Multi-Brand Control Feature ........................................ 28, 29

Tape Operation (Search System) ...................................... 30, 31

Special VCR Features ................................................ 32 ~ 34

Copying Your Tapes (Dubbing) ...................................................... 35

(Connection)

Initial Setup

Operation

Basic

Operation

VCR

Operation

DVD

DVD Operation

Disc Operation ............................................................ 36 ~ 41

DVD-RAM Operation (DVD-RAM only) .............................. 42, 43

DVD Operation using On-Screen Displays .............. 44 ~ 48

MP3/JPEG Playback Operation ................................. 49 ~ 51

Settings for DVD Operation ....................................... 52 ~ 55

A/V OPTIMIZER ................................................................... 55

Language Code List ........................................................... 56

For Your Information

Warning and Instruction Displays..................................... 57

Before Requesting Service.......................................... 58, 59

Limited Warranty .......................................................... 60, 61

Customer Services Directory ............................................ 61

Spanish (Español) Quick Use Guide......................... 62 ~ 69

Index .............................................................................. 70, 71

Information

For Your

DECK & Cassette Information

Prevent Accidental Tape Erasure

Break off the tab to prevent recording.

Record Tab

Screw driver

To record again

Cover the hole with cellophane tape.

Disc formats supported by this DECK

DECK can play back discs bearing any of the following marks:

Logo Disc type

DVD-RAM (Version 1.1 of the Video Recording Format a unified video recording standard)

DVD (DVD-Video)

DVD-R (DVD-Video formatted discs [finalized])

DVD-Audio

CD (CD-DA)

DVD-RAM discs

DVD-RAM discs must meet the following conditions for this unit to be able to play them.

Type

Capacity

• Remove TYPE 2 and 4 discs from their cartridges

before use, then return them when you are finished. Read the instructions for the disc carefully.

• Some parts of the disc, for example where one program

ends and another begins, may not play smoothly.

• Non-cartridge discs

• Discs that can be removed from their cartridges (TYPE 2 and 4)

• 12 cm (5”) 9.4 GB (double-sided) and 4.7 GB (single-sided)

• 8 cm (3”) 2.8 GB (double-sided)

Disc Handling

Handling precautions

• Sticking a label on the disc may impair DVD-R playback.

• Do not attach sticker to discs. (Do not use discs with exposed adhesive from tape or left over peeled-off stickers.)

• Only hold disc by edges as shown below. Fingerprints, dirt and scratches can cause skipping and distortion.

• Do not write on label side of disc.

• Never use record cleaning sprays, benzine, thinner, static electricity prevention liquids, or any other solvent.

Disc tray

Disc

CD-R/CD-RW

• CD-DA format

• WMA/MP3/JPEG file and

finalized.*

[Discs Played 8cm (3") or 12cm (5")] *A process that allows play on compatible equipment.

Discs which cannot be played

• DVD with Region No. other than “1” or “ALL”

• PAL discs (the audio on DVD-Audio can be played), DVD-ROM, DVD-RW, DVD+R, DVD+RW, CD-ROM, CDV, CD-G, CVD, SVCD, SACD, CD-TEXT, Divx Video Disc, Photo-CD and Video CD

Notes

• Do not use irregularly shaped discs (e.g. heartshaped), as these can damage the unit.

• It may not be possible to play CD-R, CD-RW, DVD-R and DVD-RAM in all cases due to the type of disc or condition of the recording.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

• Do not try to close disc tray when disc is not properly placed.

To clean disc surface

With a soft, damp (water only) cloth, gently wipe from the center hole to the outer edge as shown below. (Wiping in a circular pattern will scratch the surface.)

• DVD-RAM, DVD-R : Clean only with the DVD-RAM disc cleaner available. Never use cloths or cleaners for CDs etc.

If disc is brought from a cold to a warm environment, moisture may form on the disc

Wipe away moisture with a soft, dry, lint-free cloth before using disc. (See above.)

Improper disc storage

Discs could be damaged if stored or left in areas:

• exposed to direct sunlight.

• that are humid or dusty.

• near heat (i.e. heater, radiator, etc.).

Specifications

Power Source: 120 V AC, 60 Hz Power Consumption: Power On: Approx. 28 watts, Power Off: Approx. 0.85 watts

Video Signal: EIA Standard NTSC color Video Recording System: 4 rotary heads helical scanning system

Audio Track: 1 track (Normal), 2 channel (Hi-Fi Audio Sound) Tuner Broadcast Channels: VHF 2 ~ 13, UHF 14 ~ 69 CABLE Channels: Midband A through I (14 ~ 22), Superband J through W (23 ~ 36)

Input/Output Terminal: Audio/Video Line Input/Output, RF Input/Output Input Terminal: Audio/Video Line Input (Front) Output Terminal: S-Video Output (DVD only), Component Video Output (DVD only)

Operating Temperature: 5 °C ~ 40 °C (41 °F ~ 104 °F) Operating Humidity: 10 % ~ 75 % Weight: 3.85 kg (8.5 lbs). Dimensions: 430 (W) x 95 (H) x 273 (D) mm

Discs Played (1) DVD-Video Disc 5” (12 cm) single-sided single-layer

DVD-Audio Disc 5” (12 cm) single-sided double-layer

DVD-RAM Disc 5” (12 cm) 9.4 GB (double-sided) and 4.7 GB (single-sided)

(2) Compact Disc 5” (12 cm) disc

(CD-DA) 3” (8 cm) disc (CD-R/CD-RW, MP3, WMA, JPEG)

Digital Audio Output: Digital Optical Connector Pickup: Wavelength: 655 nm (DVD), 790 nm (CD)

Note: • Designs and specifications are subject to change without notice.

Hyperband AA ~ EEE (37 ~ 64), Lowband A-5 ~ A-1 (95 ~ 99) Special CABLE channel 5A (01), Ultraband 65 ~ 94, 100 ~ 125

Audio Output 2 (L), (R)

16-15/16” (W) x 3-3/4” (H) x 10-3/4” (D) inch

5” (12 cm) double-sided double-layer (one layer per side) 3” (8 cm) single-sided single-layer 3” (8 cm) single-sided double-layer 3” (8 cm) double-sided double-layer (one layer per side)

3” (8 cm) 2.8 GB (double-sided)

Laser power: CLASS II

(Connection)

Initial Setup

Definition of Terms (DVD)

Angle: Some DVD discs feature scenes simultaneously shot from different angles.

Chapter Number:Titles are subdivided into numbered sections. You can quickly search for

DVD: A high-density optical disc on which high-quality pictures and sound have

Subtitles: Written dialogue which appears at the bottom of the screen. Time Number: The elapsed play time from the start of a disc or title. Use to quickly find

Title Number: For DVD discs with two or more titles, the title is numbered as title 1, title 2, etc. Track Number: Numbers assigned to tracks on CDs to allow specific tracks to be quickly

Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, 4,819,098 and 4,907,093, licensed for limited viewing uses only.

This product incorporates copyright protection technology that is protected by method claims of certain U.S. Patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

The ANGLE button can be used to view the scene from different angles. (ANGLE Indicator lights on DECK when a scene recorded at different angles is detected.)

a favorite scene using these numbers.

been digitally recorded. DVD incorporates video compression technology (MPEG II) and high-density recording technology which allow entire movies to be recorded with incredible playback quality.

scenes. (May not work with some discs.)

located.

Location of Controls

Remote Control

EJECT

OPEN / CLOSE

pp. 20,

POWER

NUMBER keys

ADD/DELETE

pp. 19,

ACTION

pp. 18

SET

VCR mode

p. 28

STOP

pp. 20,

REWIND

SLOW-

pp. 20,

FAST FORWARD

SEARCH/SLOW+

pp. 20,

PAUSE

pp. 20,

ANGLE

SUB TITLE

TITLE DIRECT NAVIGATOR

, 52

. 37

. 36

. 38, 42

STILL

CLEAR

Bold: VCR Function /

Italic

DVD Function

Bold Italic:VCR and DVD Functions

/ Normal: Others

TRACKING/V-LOCK

CHANNEL

pp. 4, 21,

VOLUME+/

MENU/ PLAY LIST

DVD mode

Virtual Surround Sound (V.S.S.)

TAPE POSITION/STATUS

VOLUME ADJUST

AUDIO

(SAP / Hi-Fi)

VCR/TV

TV mode

. 38, 43

SELECT

PLAY

pp. 20,

SKIP+

SKIP-

ENTER

. 23,

ZOOM

p. 31,

pp. 27,

p. 21

p. 28

. 23

. 37

RETURN

INPUT

p. 35

DISPLAY

p. 11,

RECORD

p. 21

SPEED

p. 21,

EJECT button: When this button is pressed in VCR mode, the tape is ejected.

PAGE

This button is inoperative if pressed during recording. If pressed in DVD mode, the disc tray opens or closes.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

COMMERCIAL SKIP

. 22,

ZERO SEARCH

A/V OPTIMIZER

pp. 30,

COUNTER RESET

p. 30

PROGRAM

p. 24

Front View of DECK

Bold: VCR Function

Italic

DVD Function

Bold Italic

Normal: Others

PLAY

p. 20

VCR and DVD Functions

If the disc cannot be removed...

First, unplug DECK. Then, prepare a rigid wire (e.g. an extended paper clip) and, applying moderate force, insert it straight into the hole at the base of the tray. The tray will eject a little. Now, pull the tray all the way out and remove the disc.

(Connection)

Initial Setup

STOP/EJECT

p. 20

Remote Sensor

POWER

Audio/Video Input Connector 2 (LINE 2)

REC

p. 21

CHANNEL / TRACKING/V-LOCK

pp. 4, 21

p. 35

Blue Light

Reset All Memory Functions

Cassette Compartment

p. 32

Multi Function

Display

p. 11

Over 2 inches

Disc Tray

OPEN/CLOSE

FAST FORWARD

REWIND

SKIP

p. 20,

SKIP

p. 20,

PLAY

STOP

Returns to factory setting. Use if relocating DECK, or if Initial Setup needs to be redone.

• Make sure a tape is not inserted in the DECK.

Turn DECK Power on.

Press and hold both VCR PLAY

and CHANNEL on the DECK for more than 5 seconds.

• The power shuts off. Perform “Initial Setup (Ready to Play)”

121

on page 16.

Location of Controls (continued)

Rear View of DECK

AC Power Plug

• While plugged into an AC outlet, this DECK consumes 0.85 W of electrical power in off mode.

Component Video Output Connector (Y, PB, PR) (DVD Only)

Optical Digital Audio Output Connector (DVD Only)

S-Video Out Connector (DVD Only)

pp.

10, 13

Bold: VCR Function

Bold Italic:VCR and DVD Functions

VHF/UHF Antenna Output Terminal p.12

VHF/UHF Antenna Input Terminal p. 12

Video Output Connector

•

Video Input Connector p. 35

•

Audio Output 1 Connector (L/R)

Audio Output 2 Connector (L/R)

Audio Input Connector (L/R) p. 35

Italic:DVD Function

The following table shows the status of the output jacks when in VCR or DVD mode.

Video Output Audio Out 1 Audio Out 2

VCR

DVD

• PROG functions on the remote are not available when using Component Video Output and

Note

S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROG.

YES YES

Component Video Output

N/A

S-VIDEO OUT

N/A

YES

To enjoy PROGRESSIVE SCAN video

(1). Connect

(See p. 13.)

(2). When PROGRESSIVE OUT is set to “ON” in the DVD Main Menu (p. 55), a Progressive

Scan signal is output from the

Notes

• The screen may shift off-center when using progressive output. Please adjust the screen position if this occurs. (Refer to your TV manual.)

• If the television is not progressive compatible, a progressive scan picture is not available. Connect the Video Output or S-Video Output connector (see p. 12, 13) and set PROGRESSIVE OUT to “OFF” in the DVD Main Menu. (See p. 55.)

Component Video Output

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

to the component video input terminals of a television.

Component Video Output Connector

Displays (On Screen & Multi Function)

On Screen Displays (VCR)

(Connection)

Initial Setup

Function & Channel Displays

CH 0 8

When a function button is pressed, e.g. PLAY, or you change channels, a 5-second display appears.

VCR Status & Clock Displays To display or remove screen shown at right,

➛➛

➛ press DISPLAY.

➛➛

Rec Time Remaining (OTR mode only, see p. 21.)

Multi Function Display

VCR mode Indicator

Lights up when DECK is in VCR mode.

Timer Indicator

Lights up when DECK is set for Timer Recording, or when One Touch Recording (OTR) is used. Flashes when Timer Recording is set, but a tape has not been inserted into DECK and when a power interruption occurs during Timer Programming.

DTS Indicator

Lights up when a DTS formatted DVD is played. (DVD only)

Dolby Digital Indicator

Lights up when a “Dolby Digital” formatted DVD is played. (DVD only)

Tape Indicator

Lights up when a tape is inserted.

VCR

TIMER REC

DIGITAL

Broadcast Audio Being Received (See pp. 26, 27.)

VCR REC Indicator

Lights up during recording.

Hi - Fi

Hi-Fi Indicator

Lights up when Hi-Fi audio is present in Play mode.

Blank Tape/ No Video Signal Indications

Whenever a blank section of a tape comes up in Play mode, or when the selected channel has no broadcast signal with Weak Signal Display Feature (p. 33) set to OFF, the TV screen will turn solid blue.

Current Time

Function Status

DISC Indicator

Lights up when a disc is inserted.

REW 0:25 STER SAP M

ONO

12:00A

-0:12:

Channel

02 34 SP

DVD mode Indicator

Lights up when DECK is in DVD mode.

CD/MP3/WMA Indicator

CD : Lights when an

DVD

MP3

AM PM

WMA

ANGLE

MP3/WMA :

ANGLE Indicator

AM/PM Indicator

Lights up when a scene recorded at different angles is detected. (See p. 37.) (DVD only)

Clock/ Status/ Channel/ Speed Display

Displays current time. Briefly displays DECK status when you press a function button, channel number or “L1” or “L2” when you select channel or line input, and recording speed when you press SPEED.

Counter

Tape Speed (See p. 4.)

Audio CD is inserted or JPEG file is played.

Lights when an MP3 or WMA file is played.

Connections

Basic Connections

• If your TV has AUDIO and VIDEO IN terminals, connect them to DECK for higher

quality picture and sound.

• You can enjoy stereo sound even if your TV is not stereo by connecting a stereo

amplifier to DECK.

• Connect DECK and TV with an RF Coaxial Cable a (supplied) or an AV Cable (not supplied) as shown in the figure below.

■ ■

■ DSS Receiver DECK TV

■ ■

■ DECK TV

■ ■

Antenna or Cable

■ Cable Box DECK TV

■ ■

DSS Receiver

OUT

DVD/VCR DECK

IN FROM ANT.

IN 1

OUT

VIDEO

AUDIO

When using “Nut type” RF coaxial cables, tighten with fingers only. Overtightening may damage terminals.

VHF/UHF

OUT TO TV

OUT

Cable Box

1 Disconnect antenna or cable from TV

and connect to DECK.

2 Connect DECK to TV with RF Coaxial Cable.

RF COAXIAL CABLE

AUDIO IN

(supplied)

VIDEO

AV CABLE

VHF/ UHF

(not supplied)

Note to CABLE system installer

This reminder is provided to call the CABLE system installer’s attention to Article 820-40 of the NEC in USA (and to the Canadian Electrical Code in Canada) that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Other Connections

■ ■

■ With a Cable Box (DECK

■ ■

DVD/VCR DECK

IN FROM ANT.

IN 1

OUT

VHF/UHF

OUT TOTV

■■

■

Connect With Two Cable Boxes

■■

ANT or CATV

Cable Box

Cable Box TV)

OUTIN

DVD/VCR DECK

ANT

CATV

Cable Box

OUT

2-Way Splitter

OUT 1

OUT 2

OUT

Cable Box

OUTIN

IN 1

IN FROM ANT.

VHF/UHF

OUTTO TV

A/B Switch

VHF/ UHF

IN 2IN 1

• view any (including

• use Remote

• record and view

AUDIO

VIDEO

scrambled) channel.

Control to select channels without using Multi-brand control feature.

both scrambled and unscrambled channels if additional equipment is added. This connection requires: two converter boxes, an A/B switch, and a 2-way splitter.

OUT

AUDIO

VIDEO

OUT

R L

VHF/ UHF

You CannotYou Can

• record scrambled channels.

You CannotYou Can

• view a channel other than the one selected for any type of recording.

• set a Timer recording of a channel unless you select it on the Cable Box.

Connections For DVD Only (enjoying higher picture quality)

Connect AUDIO OUT2 (L, R) to the AUDIO IN (L, R) of the TV. (audio input for COMPONENT

or S-VIDEO mode). If your TV has COMPONENT VIDEO INPUT, connect to COMPONENT VIDEO OUT.

If your TV does not have COMPONENT VIDEO INPUT but has S-VIDEO INPUT, connect to S-VIDEO OUT.

When in DVD mode, set your TV to either COMPONENT VIDEO IN or S-VIDEO IN.

Notes

• You can watch DVDs through the S-VIDEO or COMPONENT VIDEO, VHF/UHF OUT TO TV, and VIDEO OUT connections to your TV. The VCR and TUNER pictures are available only from the VIDEO OUT and VHF/UHF OUT TO TV connections to your TV.

• PROG functions on the remote are not available when using S-VIDEO OUT and COMPONENT Video Output. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROG.

• TV must have capability to accept and display a progressive scan signal to use PROGRESSIVE mode. Consult your TV operating instructions.

DVD/VCR DECK

DVD OUTPUT

S-VIDEO OUT

COMPONENT

VIDEO OUT

P R

AUDIO OUT2

AUDIO

VIDEO

S-VIDEO IN

From DECK’s

A/V OUTPUT

(Connection)

Initial Setup

Connections (continued)

Audio Connections

Ready Checklist

Turn down the volume, then turn DECK, as well as other equipment to be connected, off before proceeding with connection. Do not block ventilation holes of any of the equipment and arrange them so that air can circulate freely. Read through the instructions before connecting other equipment. Ensure that you observe the color coding when connecting audio and video cables.

■ Connecting Amplifier (2ch stereo system)

DVD/VCR DECK

Speaker

AUDIO OUT2

L R

Enjoying digital audio output from the digital audio output connector

Notes on audio output from the optical digital audio output connector

Amplifier

AUDIO IN

R L

Speaker

Disc

DVD

Sound recording format

Dolby Digital

Linear PCM (48/96/192/44.1/88.2/

176.4 kHz 16/20/24bit) DTS

DVD-RAM

Dolby Digital

Linear PCM(48 kHz/16 bit)

CD MP3

WMA

*1 The type of audio output from the connector can be selected by the Settings for DVD

Operation. (See p. 53.)

*2 When “LPCM(DVD)” is set to OFF in the DVD Main Menu, 44.1 or 48 kHz sampling/16 bit is

ouput. When set to ON, sampling of sound quality greater than 44.1 or 48 kHz/16 bit is reduced to 44.1 or 48 kHz/16 bit. (See page 53.)

Linear PCM MP3

WMA

Optical digital audio output from connector

Dolby Digital bitstream (1-5.1 ch) or PCM (48 kHz sampling/16 bit only)*

Linear PCM (2 ch) (48 kHz sampling/16 bit or 44.1 kHz sampling/ 16 bit)*

Bitstream or PCM (48 kHz sampling/16 bit only)* Dolby Digital bitstream (1 - 5.1 ch)

or PCM (48 kHz sampling/16 bit only) Linear PCM (2 ch) Linear PCM (44.1 kHz sampling) Linear PCM (It depends on the MP3 file) Linear PCM (It depends on the WMA file)

For your reference:

• Dolby Digital is a digital sound compression technique developed by the Dolby Laboratories Licensing Corporation. Supporting 5.1-channel surround sound, as well as stereo (2-channel) sound, this technique enables a large quantity of sound data to be efficiently recorded on a disc.

• Linear PCM is a signal recording format used in CDs. While CDs are recorded in 44.1 kHz/16 bit, DVDs are recorded in 44.1 kHz/16 bit ~ 192 kHz/24 bit.

• If you have a Dolby Pro Logic Surround decoder, you will obtain the full benefit of Pro Logic from the same DVD movies that provide full 5.1 channel Dolby Digital soundtracks, as well as from titles with the Dolby Surround mark. For information on Panasonic or Technics Dolby Pro Logic Surround Sound Decoders please contact your local dealer.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

■ Connecting Amplifier (5.1 ch Surround system) [Digital connection] DECK Dolby Digital Decoder Amplifier Speaker

DECK DTS (Digital Theater Systems) Decoder Amplifier Speaker

When DVDs recorded in Dolby Digital or DTS are played, Dolby Digital bitstream or DTS bitstream is output from the DECK OPTICAL digital audio output connector. When DECK is connected to a Dolby Digital decoder or DTS decoder, you can enjoy theater-quality audio in your home. [An optical digital audio cable (optional) is required when an optional Dolby Digital decoder or DTS decoder is used.]

Notes on connecting an optical digital audio cable (optional)

• Firmly connect the cable to the connector.

Surround Speaker

[5.1ch Surround system]

Surround Speaker

Center Speaker

DVD/VCR DECK (Rear)

Decoder with Dolby Digital /DTS processing (optional)

Front Speaker

(Connection)

Initial Setup

Optical Digital Audio Cable (optional)

To Optical Digital Audio Input Connector

Amplifier

Subwoofer

Caution for optical digital audio output connector:

• When connecting an amplifier (with an Optical Digital Input Connector) which does not contain the Dolby Digital or DTS decoder, be sure to select “PCM” at “Dolby Digital” and “PCM” at “dts” of the Settings for DVD Operation “Audio Output” (see p. 53). Otherwise, any attempt to play DVDs may cause such a high level of noise that it may be harmful to your ears and damage your speakers.

• When a Dolby Digital/DTS decoder is connected, please select “Bitstream” at “dts” or “Dolby Digital” of the Settings for DVD Operation “Audio Output”. If “PCM” is selected, there will be stereo sound. (See p. 53.)

• CDs can be played as usual.

Note:

• Some DTS decoders which do not support DVD-DTS interface may not work properly with DECK.

Manufactured under license from Digital Theater Systems, Inc. US Pat. No’s. 5,451,942, 5,956,674, 5,974,380, 5,978,762, 6,487,535 and other US. and world-wide patents issued and pending. “DTS” and “DTS 2.0 + Digital Out” are trademarks of Digital Theater Systems, Inc. Copyright 1996, 2003 Digital Theater Systems, Inc. All Rights Reserved.

Manufactured under license from Dolby Laboratories. “Dolby,” “Pro Logic,” and the double-D symbol are trademarks of Dolby Laboratories.

Initial Setup for Basic Connections (Ready to Play)

Before doing Initial Setup

Turn TV on.

See connections a RF Coaxial Cable Connection and b AV Cable Connection on page 12.

Set TV to channel 3.

Set TV to VIDEO.

[DECK

• Go to “Initial Setup (Ready to Play).” (See below.)

[Cable Box

• Turn on Cable Box and set it to your Public Broadcasting Station (PBS) channel

• If you use a DSS Receiver, it must be turned off.

Initial Setup (Ready to Play)

Press VCR on remote for VCR mode.

Plug DECK Power Cord into AC wall outlet. DECK comes on and auto channel and clock set starts.

• If screen below does not appear, check DECK - TV connection and, if TV is tuned to

• To change VCR’s output channel, please see “VCR’s Output Channel” on page 19.

➛➛

➛ TV]

➛➛

➛ DECK

➛➛

in your time zone.

channel 3, try switching it to channel 4.

➛➛

➛ TV], [DSS

➛➛

Plug VCR Power plug into an AC wall outlet.

➛➛

➛ DECK

➛➛

➛ TV]

➛➛

CH AUTO SET PROCEEDING

CANCEL : STOP

AUTO CLOCK SET

PROCEEDING

CANCEL : STOP

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Notes

• Function buttons are void during Initial Setup.

• To eject a tape during Auto Set, press EJECT on remote or STOP/EJECT twice on DECK. Then make settings manually. (See p. 18.)

• If Auto Clock Set takes more than 30 minutes, press STOP and perform settings manually. (See p. 18.)

Continued on next page...

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Settings are made automatically. When complete, this screen appears.

EJECT

If “AUTO CLOCK SET IS INCOMPLETE”

ACTION

appears, manually set clock (below).

SELECT

SET

VCR

AUTO CLOCK SET

INCOMPLETE

PLEASE SET CLOCK BY PRESSING ACT

ON KEY

Manual Clock Set

(Connection)

Initial Setup

STOP/EJECT

If Auto Clock Set was incomplete.

Press ACTION* on remote to display CLOCK screen.

SETCLOCK

1 / 1/2004

-----------------------

SELECT : END:ACTIO

Press set. In the same manner, select and set

to select the month and SET to

THU

-- -12:00 DST:ON

SET : SET

the date, year, time, and DST (Daylight Saving Time).

SETCLOCK

6 /20/2004

-----------------------

SELECT : START:ACTIO

Press ACTION to start clock and exit.

SUN

- -15:30 DST:ON

SET : SET

Reset Language, Channels, Clock,

SET UP VCR

SET UP CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

SELECT : EXIT

: ACTION

SET : SET

Press ACTION*

to display MENU.

Language

1) Press to select

language item.

MENU SET UP VCR SET UP CLOCK SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

SELECT : EXIT

2) Press SET repeatedly to

change language item as shown below.

MENU PREPARAR VCR FIJAR RELOJ FIJAR CANAL

LANGUE/LANGUAGE:ESPAÑOL

SALIDA DE VCR CANAL : 3

ELEGIR : SALIR

For Spanish

MENU SET UP VCR SET UP CLOCK SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

SELECT : EXIT

3) Press ACTION to exit.

SET:SET

: ACTION

FIJAR:SET

: ACTION

For French

SET:SET

: ACTION

For English

➡

• PROGRAM functions are not available when using COMPONENT Video Output and S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROGRAM.

Channels

1) Press to select

“SET UP CHANNEL,” and press SET.

MENU SET UP VCR SET UP CLOCK

SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

SELECT : EXIT

2) Press to select

“ANTENNA,” then press SET to set your antenna system (“TV” or “CABLE.”)

SET UPCHA

ANT

ENNA:CABLE

AUTOSET WEAK

SIGNAL D I

SELECT EXIT:ACTIO

3) Press to select

“AUTO SET,” then press SET.

• If you use a Cable Box, set it to the PBS channel in your time zone.

CH AUTO SET PROCEEDING

CANCEL : STOP

• After Channel Auto Set is finished, Auto Clock Set will be performed.

: ACTION

SET:SET

NNE

SPLAY: OFF

SET:SET

Clock

1) Press to select

“SET CLOCK,” and press SET.

MENU SET UP VCR

SET UP CLOCK

SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

SELECT : EXIT

2) Press to select “MANUAL,” and press SET. (For Auto Clock Set, select “AUTO CLOCK SET.”)

AUTOCLOCK SET

MANUNUAL

TIMEZONEAD

SELECT : EXIT:ACTIO

(“TIME ZONE ADJUST”

appears only when auto clock is set.)

1 / 1/2004

-----------------------

SELECT : END:ACTIO

3) Press and to

select, then set the date, time, and DST (Daylight Saving Time).

4) Press ACTION to start

Clock and exit this mode.

: ACTION

SETCLOCK

JUST:

SET : SET

SETCLOCK

THU

SET : SET

SET:SET

-- -12:00 DST:ON

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

HANNEL

08DELET

VCR’s Output Channel

*Important: If a remote control button does not work

when pressed, press the VCR button on the remote and try the button again.

Time Zone Adjust

(Only when Auto Clock is set.)

1) Press to select

“SET CLOCK,” and press SET.

MENU SET UP VCR

SET UP CLOCK

SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

SELECT : EXIT

2) Press to select

: ACTION

SET:SET

VCR’s Output Channel

1) Press to select

“VCR’S OUTPUT CH.,” and press SET.

MENU SET UP VCR SET UP CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

SELECT : EXIT

2) Press SET.

: ACTION

SET:SET

“TIME ZONE ADJUST,”

SETCLOCK

AUTOCLOCK SET MANU

TIMEZONEAD

SELECT: SET:SET EXIT:ACTIO

JUST:

and press SET to

PRESS ACTIO KEY, VCR’ S S

ITCHESTOCH4

3) Press ACTION.

PLEASE TUNE YOUR TV TO CH4.

UTPUT CH

I F YOU

subtract or add hour(s) as necessary.

3) Press ACTION.

• “TIME ZONE ADJUST” returns to “0” if clock is set manually.

➡

After 3 seconds

MENU SET UP VCR SET UP CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:4

SELECT : EXIT

: ACTION

SET:SET

• To Make Corrections, repeat steps 1) ~ 3).

POWER NUMBER

keys CH /

ADD/DLT ACTION SELECT

SET VCR

Add or Delete a Channel

To add channel: Select channel with NUMBER keys

and press ADD/DLT.

HANNEL

ADDED

To delete channel: Select channel with CH / or

NUMBER keys and press ADD/DLT.

DST (Daylight Saving Time)

DECK auto adjusts clock for DST. (p. 17.)

Spring (First Sunday in April)

DST:ON

Autumn (Last Sunday in October)

DST:ON

➛➛

➛ Sets clock ahead one hour.

➛➛

➛ Turns clock back one hour.

➛➛

Operation

Basic

• If your area does not observe Daylight Saving Time, select DST:OFF.

• Keep these time changes in mind when programming DECK for timer recordings.

Playback/ Record on a Tape

Ready Checklist

All connections are made. (pp. 12 ~ 15) TV and DECK are plugged in. TV is on and tuned to CH 3, 4, or VIDEO. Remote is in VCR mode. (Press VCR.)

Playback a Tape

Insert a tape.

• DECK power comes on. If Auto VCR/TV (see p. 32) is set to “OFF,” press VCR/TV on the remote for VCR mode.

Press PLAY* to play a tape.

• If tape has no rec. tab (p. 6), auto play begins.

Special Features During Play

Forward/Reverse Scene Search

➛➛

➛ Press FF/SLOW+ or REW/SLOW-.

➛➛ ➛➛

➛ Press PLAY to release.

➛➛

After search has begun, each additional press of

FF or REW changes speed

Notes

• Picture interruption may occur with some TVs.

• FF and REW search speed may vary depending on current tape position.

• After 10 minutes in search mode, VCR returns to Play mode to protect the tape and the video heads.

Still (Freeze) Picture

➛➛

➛ Press PAUSE/STILL.

➛➛ ➛➛

➛ Press PLAY to release.

➛➛

Frame by Frame Picture

➛➛

➛ Press PAUSE/STILL in Still mode.

➛➛ ➛➛

➛ Press PLAY to release.

➛➛

Slow Motion Picture

➛➛

➛ Press FF/SLOW+ (increase speed) or

➛➛

REW/SLOW- (decrease speed) in Still mode.

➛➛

➛ Press PLAY to release.

➛➛

EJECT

VCR

FF/ SLOW+

REW/ SLOW-

PAUSE/ STILL

REC

Notes

• These features work best in SP or SLP mode.

• The sound will be muted.

• To reduce picture noise, see “Manual Tracking Control” on page 4.

• After 3 minutes in Still or Slow mode, VCR stops to protect the tape and the video heads.

VCR/TV

CH /

DVD

PLAY

STOP

SPEED

Playback using DECK buttons

Insert a tape.

Press PLAY.

Press STOP to stop a tape.

Rapid Rewind/FF

Press REW/SLOW- or FF/SLOW+ in Stop

mode to rewind or fast forward a tape.

• Rewinds a T-120 tape in approx. 1 minute.

Press EJECT on remote, or STOP/EJECT on DECK to eject a tape.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Multi Function Display

Press STOP/EJECT to stop and/ or eject a tape.

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Record on a Tape

Insert a tape with a record tab (p. 6).

• DECK power comes on. If Auto VCR/TV (see p. 32) is set to “OFF,” press VCR/TV on the remote for VCR mode.

Press CH , or NUMBER keys

to select the channel.

• If channel number is over 100, first press 100 key then the other 2 digits.

• For “LINE” input, see p. 35.

Press SPEED

to select the record speed (p. 4).

SP = Standard Play SLP = Super Long Play

• Speed appears on-screen and on Multi Function Display.

Press REC

to start recording.

(The VCR REC indicator lights up on Multi Function Display),

• To edit out unwanted scenes, press PAUSE/STILL to pause, and again to resume recording.

• You cannot view another channel during recording.

Press STOP

to stop recording.

One Touch Recording (recording in progress),

➛➛

➛ press REC repeatedly to set the recording length

➛➛

(30 min. ~ 4 hours) (see right).

• DECK shuts off after the preset record length.

Record one station, watch another,

➛➛

➛ press VCR/TV on the remote

➛➛

(change to TV mode),

➛➛

➛ select channels at TV (recording continues).

➛➛

Select Channels at DECK (In Stop or Rec. Pause mode)

➛➛

➛ press VCR/TV on the remote

➛➛

(change to TV mode),

➛➛

➛ select channels at DECK.

➛➛

Play a disc while recording a tape.

➛➛

➛ insert a disc during recording,

➛➛ ➛➛

➛ press

➛➛

DVD

, and then press

PLAY

This video recorder, equipped with HQ (High Quality) system, is compatible with existing VHS equipment. Only use tapes with the mark. Only tapes tested and inspected for use in 2, 4, 6, and 8 hour machines are recommended.

Note

Remove loose or peeling labels from tapes to prevent tape jam.

:00:

REC T I ME:

T I ME : CANCEL :

Normal Rec

0:30

PRESS REC KEY PRESS STOP KEY

0:30 1:00

1:302:003:004:00

Record using DECK buttons

Press REC to start recording.

Insert a tape.

Operation

Basic

Notes

• It is not possible to record from DVD/ CD to VHS tape using DECK.

• Watching one channel and recording another is not possible when using Cable Box or DSS Receiver.

• After 5 minutes in Pause mode, DECK stops to protect a tape and video heads.

Select

Channel.

Multi Function Display

Press STOP/EJECT to stop.

Basic DVD Operation

Ready Checklist

All connections are made. (pp. 12 ~ 15) DECK is plugged in. If DECK is connected to an audio amplifier,

turn the stereo system’s power on.

OPEN/ CLOSE

POWER

NUMBER keys

SELECT

SET FF/

SLOW+ REW/

SLOWPAUSE/

STILL TITLE

STOP DVD

PLAY

SKIP+ SKIP

VSS

RETURN

2 3

If an interactive DVD*1 is used and TITLE MENU appears, go to step 5.

Operation using DECK buttons

Press

3, 7

Press

POWER.

Insert a disc.

*1Interactive DVD...

May include multiple camera angles, stories, etc.

OPEN/CLOSE.

Press PLAY.

Press STOP.6

Using NUMBER keys starts play automatically.

The number of available titles varies with each disc.

<Input

Example>

Press previous menu screen.

• SKIP function not available with all discs.

To return to menu (play stops)

Press

6 7

Press

POWER*

Press

DVD

• If a disc is already inserted, go to step 4. (Depending on the disc, playback may start automatically.)

Press

OPEN/CLOSE

and then place a disc into the disc tray.

Press

PLAY

Disc tray closes automatically.

READING

SKIP+

Please refer to disc jacket for operation information.

TITLE, MENU,

Press

STOP

Press

OPEN/CLOSE

on the remote or DECK.

to select DVD mode.

• Hold disc by its edges only (p. 6) with printed side up and use guides to place into tray.

Use 3” (8 cm)

to start playing.

• You may also close tray by

pressing

• Data reading time differs with each disc.

1 digit number 1 •••• 1 2 digit number 12 ••• 10 ➛ 1 ➛ 2

| or

SKIP-

RETURN

to stop playing.

or 5” (12 cm) disc.

DVD-RAM ➡ see p. 42

OPEN/CLOSE

TI TLE MENU

Castles

Dogs

SET

Birds

(see

PLAY

Lovers

Press or

NUMBER keys

below) to select title, and press

PLAY

to start playing.

• Pressing is not necessary when using

NUMBER keys.

| to go to next or

to eject the disc.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

*Important: If a remote control button does not work when pressed,

VSS OFF (default)

VSS1

VSS3

VSS2

press the DVD button on the remote and try the button again.

■ Forward/Reverse Scene Search

Press Press

• Search speed, slow at first, increases with each additional press of the button up to 5 levels.

■ Forward/Reverse Chapter/Track Skip

Press

Each press skips a chapter (DVD-Video), track (DVD-Audio/CD) or Program/Play List/ Marker (DVD-RAM).

DVD-Video, DVD-Audio and CD

• Pressing

chapter/track returns to the start of that chapter/track. Each additional press skips back one chapter/track.

DVD-RAM

• Pressing

program/play list returns to the start of that program/play list. Each additional press skips back one program/play list.

■ Still Picture or Pause

Press Press

• DVD : DECK will enter still picture mode.

• CD : DECK will enter pause mode.

■ Frame by Frame Picture (DVD)

Press Press

• Each press advances picture one frame.

• Hold button down for consecutive frame advance.

• Whether pictures are advanced by “FRAME” or “FIELD” is selected automatically. (See p. 54.)

■ Slow Motion Picture (DVD)

Press Press

• Slow motion speed, slow at first, is increased with each additional press of the button up to 5 levels.

Auto-Power Off Function

Power turns off after DECK has been in Stop mode (DVD) for about 5 minutes.

• When appears on the screen while a button is being operated, it means that the corresponding operation is prohibited by DECK or the disc.

FF/SLOW+

PLAY

SKIP+

Chapter/Track Chapter/Track Chapter/Track

Reverse Skip Forward Skip

Current playback position Marker

Program/Play List Program/Play List Program/Play List

Reverse Skip Forward Skip

PAUSE/STILL PLAY

FF/SLOW+orREW/SLOW-

PLAY

REW/SLOW-

to release.

| or

SKIP-

| during play.

SKIP-

| once midway through a

Current playback position

SKIP-

| once midway through a

during play.

to release.

in still mode.

to release.

during play.

in still mode.

V.S.S. (Virtual Surround Sound)

Enjoy a surround-like effect if you are using two front speakers only. The effect is broadened and sound seems to come from virtual speakers on either side if the disc has surround signals recorded on it.

Press

VSS

• The Surround sound effect can be changed by pressing VSS repeatedly as shown by the figure below.

in DVD mode.

VSS OFF

Note

• Surround sound effect is available in DVD mode only.

• Turn off the surround effects on the other equipment.

• V.S.S. will not work, or will have less effect, with some discs.

• Turn V.S.S. off if it causes distortion.

• Sound will only come from the two front speakers if V.S.S. is on.

Resume Function

DECK memorizes the point where STOP is pressed (STOP is displayed on screen).

Press

PLAY

Pressing

cancels RESUME, however, RESUME is not canceled when power is turned off and on.

• RESUME works only with discs for which elapsed play time is displayed during play.

• When a DVD-RAM still picture is played back, the counter will not be displayed, however RESUME will function.

Notes

• Please read the disc jacket for operation information.

• If a single sided disc is placed in upside down, “THIS TYPE OF DISC CANNOT BE PLAYED. PLEASE INSERT A DIFFERENT DISC” is displayed.

• Remove disc and press DECK POWER off when not in use.

• Disc continues to rotate with menu displayed even after play is done. Press STOP to clear menu display when finished with menu.

to resume play from this point.

STOP

again or opening the tray

Operation

Basic

Timer Recording

Ready Checklist

All connections are made. (pp. 12 ~ 15) TV and DECK are plugged in. Clock set correctly. (p. 18) Tape has record tab intact. (p. 6) Remote is in VCR mode. (Press VCR.) Sufficient tape remaining for recording time.

Press PROG*

to display Program.

POWER

P DT STARTSTOPCH SPD

-- --:-- --:--

SELECT : EXIT : PROG

Example

Today

SELECT /

Selection Order

WEEKLY

P DT STARTSTOPCH SPD

1 13 2:00p 3:20p 02

-- --:-- --:--

SET COMPLETED

CANCEL:ADD/DLT SELECT : EXIT : PROG

(SA)

SET :SET

1) Press .

2) Set record DATE,

press

1~31= one time, or DAILY=Monday~Friday, or WEEKLY= same time each week.

• See selection order left.

3) Set remaining items,

DAILY

WEEKLY

(SU)

WEEKLY

(MO)

press SET

to set START/ STOP times, CH (channel) or LINE input (p. 35), and tape speed (SP, SLP). Then press

Press PROG

to end programming.

To Enter More Programs,

SLP

press

to select and

press SET

to set an unused program number, and then repeat step 2.

Press PROG

to exit.

to select:

to select.

VCR mode Indicator

VCR REC Indicator

VCR

TIMER REC

Hi - Fi

TIMER Indicator

ADD/DLT

SELECT

SET VCR

PROG

• The “Timer” Indicator lights up on DECK.

• You can set Timer Recording with the power on or off.

• “TIMER REC WILL START SOON” appears on-screen for 2 minutes

before Timer Recording starts. If DECK is in DVD mode, no message appears, but the VCR REC Indicator, the VCR mode indicator and “REC” will flash on Multi function Display.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Review, Replace or Clear Program Contents:

(Recording is not in progress)

Press PROG

to display Program List.

P DT STARTSTOPCH SPD

1 13 2:00p 3:20p 02 SLP

2 14 7:00p 7:30p 10 SP

-- --:-- --:--

CANCEL:ADD/DLT SELECT : EXIT : PROG

SET :SET

To Replace program...

P DT STARTSTOPCH SPD

1 13 2:00p 3:20p 02 SLP

2 14 7

00p 7:30p 10 SP

-- --:-- --:--

SELECT : EXIT : PROG

To Clear program...

PDTSTARTSTOPCH SPD

-- --:-- --:-2 14 7:00p 7:30p 10 SP 3

-- --:-- --:-4

-- --:-- --:--

SELECT : EXIT : PROG

Press PROG

to end the programming.

SET :SET

Press

to select number.

Repeat Step 2 (p. 24) to set new programs.

Press ADD/DLT.

To cancel a Timer Recording in progress...

Hold down STOP in VCR mode for

a few seconds to cancel the Timer Recording.

(The “TIMER” Indicator goes out

on Multi Function Display.)

• Any future daily or weekly recording will be performed as programmed.

Operation

VCR

Notes

• If you are using a Cable Box, the VCR’s channel for Timer Recording must be set to the Cable Box input channel and Cable Box must be manually set to the desired channel. Cable Box power must be left on.

• 2 minutes before Timer Recording is performed, “PLEASE PREPARE FOR TIMER REC” appears and Timer Indicator flashes. Be sure a cassette with record tab is loaded and DECK is in Stop mode.

• If a power interruption occurs while programming the timer, the timer program(s) may be canceled. If “TIMER PROGRAMS WERE LOST DUE TO POWER INTERRUPTION” appears on-screen, please re-enter the timer programs.

• If the start time for Timer Recording comes up during recording and playing back, Timer Recording will not be performed.

Important notes when using DSS Receiver

• When recording programs via DSS Receiver, DSS Receiver must be left on.

• When recording programs via an antenna or cable, DSS Receiver must be turned off.

MTS Broadcast/ VHS Hi-Fi Stereo System

Connection

Make the Audio/Video Connection as shown on pp. 12 ~ 15.

• You can use TV connected to a Stereo amplifier and speakers instead of Stereo TV.

Receivable Broadcast Types

The following are possible audio broadcast types and onscreen displays.

The signal being received is indicated with a “ the selected audio mode is indicated with an arrow.

To display the broadcast signal being received,

➛➛

➛ press DISPLAY*.

➛➛

MTS Stereo and SAP broadcast

Multi-channel Television Sound Stereo (main language) and Secondary Audio Program (sub language) broadcasts are being received simultaneously. Select STEREO or SAP audio mode.

” mark while

STOP12:00A

STER

EO SAP M

ONO

:00:

MTS Stereo broadcast

Multi-channel Television Sound Stereo broadcast. Select STEREO audio mode.

• If stereo broadcast is weak and display flickers, select MONO audio mode for possible better results.

SAP broadcast

Secondary Audio Program (sub language) broadcast. Select SAP audio mode for the sub language.

MONO broadcast

Normal monaural sound broadcast.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

STOP12:00A

STER

EO SAP M

ONO

STOP12:00A

STER

EO SAP M

ONO

STOP12:00A

STER

EO SAP M

ONO

:00:

00 SP

AUDIO

(SAP/Hi-Fi)

DISPLAY

Equipped with ®-TV Noise Reduction for true MTS reproduction.

-TV Noise

Reduction is required

:00:

for good stereo separation and audio fidelity.

is a registered trademark, and is licensed by

Technology Licensing.

*Important: If a remote control button does not work when pressed,

Audio Mode for Recording

Press AUDIO (SAP/Hi-Fi)

to display audio mode.

(Display disappears after 5 seconds.)

Press AUDIO (SAP/Hi-Fi) repeatedly

STER

EO SAP M

ONO

Make a recording.

See p. 21.

to select desired mode.

• Refer to “Receivable Broadcast Types” on p. 26.

• Arrow indicates selection.

Audio Mode for Playback

press the VCR button on the remote and try the button again.

Operation

VCR

Start playback.

See p. 20.

Press AUDIO (SAP/Hi-Fi)

to display audio mode.

IFI

: L/R

IFI

: L

IFI

H N

ORM

• Arrow indicates selection.

Notes

• Only tapes recorded in Hi-Fi stereo will playback with true stereo sound. Standard stereo tapes will playback in monaural sound.

• To listen to Hi-Fi stereo playback, the DECK AUDIO (L/R) jacks must be connected to a stereo TV or an external stereo amplifier and speakers. (See pp. 12, 14.)

• If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio.

• Hi-Fi and normal audio playback volume level may differ.

Press AUDIO (SAP/Hi-Fi) repeatedly to select desired mode.

• Select “HIFI (L/R)” or “HIFI (L)” or “HIFI (R)” to listen to stereo recordings in stereo sound. Select “NORMAL” for monaural sound.

• Display disappears after 5 seconds.

Multi-Brand Control Feature

Multi-Brand Control Setup

The Remote Control can be set to control some TVs.

Find your TV Brand Code Number on the

following page.

2 3

Set up for TV control,

➛➛

➛ hold down TV button,

➛➛ ➛➛

➛ enter code with NUMBER keys.

➛➛

Confirm code entry,

➛ press POWER to turn selected unit on or off.

• See table below for controllable functions in each mode.

Notes

• Repeat setup after remote battery replacement.

• Remote will not control every TV made by the manufacturer listed. If you get no response, your particular unit cannot be controlled. There are NO additional codes for the products listed. If your product is not listed, then the remote is not compatible with that product.

Using Multi-Brand Control

After remote is set up, you can select VCR, DVD, or TV for the desired function.

Press VCR,

(Table below shows available remote buttons for each mode.)

Mode

DVD VCR

DVD

, or TV on the remote.

Unit

EJECT/

DISPLAY,PLAY,STOP FF/SLOW+,REW/SLOW-

VCR/TV, PAUSE

AUDIO

TAPE POSITION, COUNTER RESET

DVD/VCR TV

OPEN/CLOSE

, CM/ZERO, SPEED, REC,

All

/STILL,SKIP

PAGE

POWER, INPUT, NUMBER keys, ENTER, CH / , VOL +/

VOL

* Bold: VCR Function

Italic: DVD Function

Notes

• Not all functions listed may be controllable.

• In TV mode, it may be necessary to press ENTER after pressing NUMBER keys for channel selection.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Bold Italic: VCR and DVD Functions

Normal: TV

TV Brand Code Numbers

Panasonic ......................................... 01, 02

Quasar.............................................. 01, 02

RCA ......................................................... 03

GE ........................................................... 03

Zenith ...................................................... 04

Magnavox ............................................... 05

Sylvania .................................................. 05

Sharp................................................. 06, 07

Sony ........................................................ 08

Toshiba ................................................... 09

Sanyo ...................................................... 10

Fisher...................................................... 10

JVC ......................................................... 11

Hitachi ..................................................... 12

Mitsubishi .......................................... 07, 13

Samsung ................................................ 14

Gold Star .................................... 15, 16, 17

Important Notes

• Some manufacturers use several codes for one brand. If the first code entered fails, try the next one listed.

• Some TVs require you to turn on the power manually.

Operation

VCR

POWER

VCR

NUMBER keys

DVD

ENTER

Tape Operation

Search System

For each recording, an invisible index mark is placed on the tape. A program index and information are also included for timer recordings. These marks are used to access or scan recordings.

Index Search

INDEX SEARCH

ENTER INDEX NUMBER :1

USING1-

9 KEYS

FORWARD SEARCH :FF REVERSE

SEARCH :REW

EXIT

:SEARCH

INDEX SEARCH

FORWARD SEARCH : FF REVERSE

SEARCH : REW

To Calculate Index Number

Example 1:

To go to rec. 2 from rec. 4, enter 3 and press REW.

Example 2:

To go to rec. 6 from rec. 2, enter 4 and press FF.

Press SEARCH*

to display SEARCH in Stop or Play mode, and then

press NUMBER keys to select

recording number.

• To calculate number, see below.

Press FF/SLOW+

or REW/SLOW- on the remote to start search.

Play begins at search end. To search forward or back 1 index,

press FF/SLOW+ or REW/SLOW- on the

remote while screen left is displayed (10 sec.).

• To cancel, press

PLAY or STOP.

61572 34

Zero Search

To quickly return to a specified tape location.

Press DISPLAY during play

to display Counter.

PLAY

12:00A

0:00:00

Press COUNTER

RESET on remote at desired position to reset to “0:00:00”.

Continue to record, playback etc.

Press STOP.

REW

12:30AMCH

Press CM/ZERO

:30:

in Stop mode to start Zero Search.

STOP

12:31AMCH

• DECK will go into FF or REW mode and stop at the last point the Counter was set to 0:00:00.

:00:

Commercial Skip

DECK fast forwards (skips) over 1, 2, or 3 minutes of recorded tape as desired.

Press CM/ZERO in Play mode.

• The skip time can be changed by pressing CM/ZERO repeatedly as shown by the figure below.

PLAY

1st Press

1 min Skip

17534 62

NOTE: indicates start points of each recording.

Note

• If Index Search is started very close to an index mark, that index mark may not be counted in the search.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

2nd Press

3rd Press

• No indication appears on-screen.

2 min Skip

3 min Skip

*Important: If a remote control button does not work when pressed,

REPEAT

press the VCR button on the remote and try the button again.

Tape Select

Select your tape length so the tape position and amount of tape remaining are properly displayed. (See “Tape Position Display” section right.)

Press ACTION

to display MENU.

SET UP VCR

SET UP CLOCK

SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

SELECT : EXIT

REPEAT REMOTEWARNING :ON

AUTOSHU FRONT DISPLAY AUTOVCR/TV

TAPE SELECT : T-120

SELE END:ACTIO

• Select “T-120” for tapes 120 minutes or less, “T-160” if 140 or 160 minutes, and “T-180” if 180 minutes.

: ACTION

SET

UP V

PLAY

T-OFF:O

CT:

SET : SET

Press

“SET UP VCR,” and

press SET.

Press to select

:OFF

“TAPE SELECT,”

:ON

and press SET to

:ON

set “T-120,” “T-160”

SET:SET

or “T-180.”

T-120 T-160 T-180

to select

Press ACTION

to return to normal screen.

Repeat Play

Set to playback a recording over and over.

Press ACTION

to display MENU.

SET UP VCR

SET UP CLOCK

SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

SELECT : EXIT

REPEAT

REMOTEWARNING :ON

AUTOSHU FRONT DISPLAY AUTOVCR/TV TAPE SELECT : T-120

SELE END:ACTIO

• Play repeats at tape end or if unrecorded

portion over 30 sec. is detected.

: ACTION

SET

UP V

PLAY

T-OFF:O

CT:

SET : SET

Press ACTION

to return to normal screen.

Note

• For repeat play in DVD mode, see page 47.

Press

to select “SET UP VCR,” and press

SET.

Press

:OFF

to select “REPEAT

:ON

PLAY,” and press

:ON

SET to set “ON” or

SET:SET

“OFF.”

Tape Position Display

To find out the present tape position and amount of tape remaining.

Tape position is displayed incorrectly in the following cases:

• If VHS-C type cassettes, tapes under 30 minutes, tapes over 180 minutes, or incompatible tapes are used.

• If the correct tape length is not selected. (See “Tape Select” section left.)

Press TAPE POSITION

to detect current tape position.

DETECTING TAPE POSITION

R 120 MI N.

BEGIN

END

• “DETECTING TAPE POSITION” only appears the first time a cassette is inserted and it takes several seconds for correct

indication to appear.

• The present tape position indication and amount of tape remaining (according to tape speed) are displayed. Tape remaining time display may not be precise.

Press TAPE POSITION

(or wait 5 seconds) to return to

normal screen.

Auto Operation Functions

Auto Play

Insert a tape ➛ Power comes on, ➛ Play starts if there is no record tab

(see p. 6).

Auto Rewind

Play Fast Forward

➛ Tape end ➛ Rewind

Play Auto Eject

(Repeat Play must be off)

➛ ➛

➛ Tape end

Play

➛ ➛

➛ Tape ejects if some programs are set.

➛ ➛

➛ Rewind

➛ ➛

➛ Stop

➛ ➛

➛➛

➛

➛➛

Stop

Operation

VCR

Special VCR Features

VCR/TV Selector FeatureVCR/TV Selection Feature

The VCR/TV selection can be set to auto or manual.

Press ACTION*

to display MENU.

SET UP VCR

SET UP CLOCK

SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

SELECT : EXIT

REPEAT REMOTEWARNING :ON

AUTOSHU FRONT DISPLAY

AUTOVCR/TV

TAPE SELECT : T-120

SELE END:ACTIO

: ACTION

SET

UP V

PLAY

T-OFF:O

CT:

SET : SET

• OFF(Manual): You select “VCR” or “TV” mode using the VCR/TV button on the remote.

• ON(Auto): “VCR” mode is automatically set when VCR is turned on, or in Play mode.

Press ACTION

to return to normal screen.

Note

• For more on VCR/TV selection, see “Record one

station, watch another” and “Select channels at DECK” sections (see p. 21).

:OFF

FF :ON

:ON

SET:SET

Press

to select “SET UP VCR,” and

press SET.

Press

to select “AUTO VCR/TV,” and

press SET

to set “ON” or “OFF.”

Blue LIGHT ON/OFF Feature

You can turn DECK’s blue light off if you find it to be glaring.

To turn LIGHT off, press DISPLAY for 5 seconds

in VCR mode.

To turn LIGHT on, repeat above.

Notes

• This operation is not possible in power off mode.

• If you unplug DECK, DECK turns to defult setting (Blue light turns on).

Blue Light

VCR Lock Feature

When set to ON, all operations except for timer record and tape eject are prohibited. Useful for households with small children.

To turn on, hold down REC on DECK in Stop mode with no tape inserted for 7 seconds.

(Please ignore “NO CASSETTE” warning.)

VCR LOCK ACTIVA

To turn off, repeat above.

VCR LOCKOFF

• VCR Lock cancels in 24 hours.

Note

• DVD functions will work even when VCR Lock is set to ON.

TED

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

REC

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Weak Signal Display Feature

When “ON,” picture is displayed regardless of signal strength.

Press ACTION

to display MENU.

ACTION SELECT

SET

MENU SET UP VCR SET UP CLOCK

SET UP CHANNEL

IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

SELECT : EXIT

ANT

UTOSE

WEAK

SELECT EXIT:ACTIO

: ACTION

SET UPCHA

ENNA:C

SIGNAL D I

SET: SET

ABLE

NNE

SPLAY:OFF

• ON: Picture is displayed regardless of signal condition, and may not always be clearly visible.

OFF: Screen turns solid blue when signal is weak or

non-existent.

• Selecting ON has no effect on connected equipment

with blue back feature.

Press ACTION

to return to normal screen.

Press

to select “SET UP CHANNEL,” and

press SET.

Press

to select “WEAK SIGNAL DISPLAY,” and

press SET

SET: SET

to set “ON” or “OFF.”

Operation

VCR

DISPLAY

Auto Shut-Off Feature

The power shuts off at a preset time.

Press ACTION

to display MENU.

SET UP VCR

SET UP CLOCK

SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

SELECT : EXIT

REPEAT REMOTEWARNING :ON

AUTOSHU

FRONT DISPLAY AUTOVCR/TV TAPE SELECT : T-120

SELE END:ACTIO

: ACTION

SET

UP V

PLAY:O

T-OFF:O

CT:

SET : SET

SET:SET

Press ACTION

to return to normal screen.

Note

• The shut-off countdown will not function during Play or

Record.

Press

to select “SET UP VCR,” and

press SET.

Press

to select “AUTO SHUT-OFF.”

:ON

Press SET repeatedly to

:ON

change shut-off time as shown below.

OFF

2 Hours

4 Hours

6 Hours

Special VCR Features (continued)

Remote Warning Feature

If Multi-brand feature is used (p. 28), and this feature is set to on, a warning appears whenever an invalid key is pressed in TV mode.

Press ACTION*

to display MENU.

SET UP VCR

SET UP CLOCK

SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

SELECT : EXIT

SET REPEAT

REMOTEWARNING :ON

AUTOSHU FRONT DISPLAY AUTOVCR/TV TAPE SELECT : T-120

CT:

SELE END:ACTIO

: ACTION

UP V

PLAY

T-OFF:O

SET : SET

:OFF

:ON :

SET:SET

Press

to select “SET UP VCR,” and

press SET.

Press

to select

“REMOTE WARNING,” and

press SET

to set “ON” or “OFF.”

• If “OFF,” remote warning will not appear when invalid key is pressed.

Press ACTION

to return to normal screen.

Multi Function Display (Front Display) ON/OFF Feature

Multi Function Display (Front Display) can be set to ON/OFF.

Press ACTION

to display MENU.

SET UP VCR

SET UP CLOCK

SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3

SELECT : EXIT

: ACTION

SET : SET

Press

to select “SET UP VCR,” and press SET.

*Important: If a remote control button does not work

when pressed, press the VCR button on the remote and try the button again.

ACTION SELECT

SET

STOP

STILL/ PAUSE

INPUT

REC

SET

UP V

PLAY

T-OFF:O

CT:

:OFF

:ON

SET:SET

REPEAT REMOTEWARNING :ON

AUTOSHU

FRONT DISPLAY

AUTOVCR/TV:O TAPE SELECT : T-120

SELE END:ACTIO

• ON : When set to “ON,”

Multi Function Display is displayed.

OFF : When set to “OFF,”

Multi Function Display is not displayed. If a Timer Program is set, Multi Function Display is displayed.

Press ACTION

to return to normal screen.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Press

to select “FRONT DISPLAY,” and

press SET

to set “ON” or “OFF.”

Multi Function Display

(Front Display)

Copying Your Tapes (Dubbing)

Connection

VCR/ Camcorder (Hi-Fi)

VIDEO

AUDIO

OUT

L R

Connect VIDEO OUT terminal on Playing VCR to VIDEO IN terminal on DECK. To monitor the dubbing, also connect TV as shown.

Connect “L” and “R” AUDIO OUT terminals on Playing VCR to “L” and “R” AUDIO IN terminals on DECK.

In place of Playing VCR, you can use other equipment, such as a Camcorder. Simply connect the unit’s Audio/Video outputs to DECK.

DVD/VCR DECK

IN 1

VIDEO AUDIO

OUT

IN FROM ANT.

VHF/UHF

OUTTO TV

VHF/

UHF

Front of DECK

VIDEO IN 2

(Audio/Video In Terminals on the front of DECK are available)

L-AUDIO IN2-R

Playing (Source) VCR

Insert a pre-recorded tape.

1 2

Press PLAY, then PAUSE

immediately to enter PLAY/PAUSE mode.

The operation of steps 4 and 5 must be done on the playing and recording VCRs at the same time.

Press PLAY to start dubbing.

Playing VCR starts playback.

Press STOP to stop dubbing.

To Monitor Dubbing on TV

1 Turn TV on and tune to the Recording

VCR channel (CH 3 or CH 4).

2 If Auto VCR/TV (see p. 32) is set to

“OFF,” press VCR/TV on the remote for VCR mode.

• Dubbing tapes protected with Copy

Note

Caution: • Unauthorized exchanging and/or copying of copyrighted recordings may be

Guard will result in poor quality recordings.

• Please note that some tapes cannot be dubbed on DECK. Also, it is not possible to dub DVD/ CD to VHS tapes using DECK.

• When appears on the screen while a button is being operated, it means that the corresponding operation is prohibited by DECK or the disc.

Recording (Editing) DECK

Insert a blank tape with record tab.

Press INPUT to set DECK Input mode to LINE for Video Input.

(See “Selecting the Input Mode” below.)

Press REC, then STILL/PAUSE immediately to enter REC/PAUSE mode.

Press STILL/PAUSE to start dubbing. DECK starts recording.

Press STOP to stop dubbing.

Selecting the Input Mode

Method 1: Press INPUT repeatedly.

Method 2: Press CH / .

Press

• “L1” or “L2” lights up on Multi Function Display (about 4 seconds) when LINE1 or LINE2 is selected.

• LINE1: For rear audio/video connection. LINE2: For front audio/video connection.

Channel Number

Display will change as below.

LINE1

LINE2

(CABLE)

125

↔↔

↔ LINE1

↔↔

(TV)

↔↔

↔ LINE2

↔↔

Press

Operation

VCR

Disc Operation

SELECT

AUDIO

Subtitle Language (DVD only)

You can select a different subtitle language (if offered) than the one set at the Settings for DVD Operation. (See p. 52.)

Press

SUB TITLE

in Play mode to display

the subtitle selection on-screen.

• Display disappears after 5 seconds.

• When no subtitles are offered, “-” will be displayed instead of the language number.

Press

SUB TITLE

NUMBER keys

, , or

to select a

desired language.

Te amo

Subtitle language being played back (see chart, right).

Notes

• If after several presses of the button the language does not change, language selection is not offered on the disc.

• When disc is removed, subtitles revert to initial setting language. If the initial language is not recorded on the disc, the disc’s priority language will appear.

• With DVD-RAM, the subtitle can only be set to ON/OFF. The subtitle language cannot be selected.

• Subtitles may not change to the selected language immediately.

Audio Soundtrack Language (DVD only)

You can change the audio soundtrack language, selected at the Settings for DVD Operation, to a different language if available. (See p. 52.) (This operation works only with discs on which multiple audio soundtrack languages are recorded.)

Press

AUDIO

in Play mode to display the audio selection on-screen.

• Display disappears after 5 seconds.

Information of the audio stream currently being played back is displayed. (See page 53.)

Press

AUDIO

NUMBER keys

, , or

to select

desired language.

Audio soundtrack language being played back (see chart, above right).

Ready Checklist

Please read “Basic DVD Operation” on page 22.

[Subtitle language] [Audio sound track language]

ENG FRA DEU ITA ESP

NLD SVE NOR DAN POR RUS JPN

CHI

KOR

MAL

VIE

THA

∗

• Change the No. by pressing , and press

English French German Italian Spanish Dutch Swedish Norwegian Danish Portuguese Russian Japanese Chinese Korean Malay Vietnamese Thai Other

SET

[Audio attribute 1 type, sampling frequency, bit No. of the disc (see p. 53.)]

LPCM

Dolby Digital

DTS

192 kHz

1 ch - 5.1 ch 1 ch - 5.1 ch

20 bit 24 bit

Dolby Digital disc DTS disc

Linear PCM disc

16 bit

44.1 kHz

Notes

• If, after several presses of the AUDIO button the language does not change, language selection is not offered on the disc.

• When disc is removed, language reverts to initial setting. If this language is not recorded on the disc, the language recorded will be heard.

• With DVD-RAM, Audio Soundtrack Language cannot be set. Audio stream and Audio mode (LR/L/R) setting can be made. Audio stream operation method is the same as Audio Soundtrack Language. Press to move the cursor to Audio mode, then press AUDIO or

to select LR/ L/ R.

AUDI O: 1 LR

Dolby Digital 3/2.1ch

:AUDIO

SELECT

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Important: if a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

When appears on the screen while a button is being operated, it means that the corresponding operation is prohibited by DECK or the disc.

ANGLE Indicator

Notes

• The ANGLE Indicator lights up on DECK when a scene recorded at different angles is detected.

• The angle number can be set beforehand so that the angle is switched whenever the ANGLE Indicator lights up.

NUMBER keys

SELECT

SET

Multiple Angle Viewing (DVD only)

DVDs may contain scenes shot from multiple camera angles allowing the same scene to be viewed at different angles. You can view these angles, if available, using the ANGLE button.

Press

ANGLE

SELECT : ANGLE

Number of angle being played back.

Note

This function not available with DVD-RAM.

in Play mode to display the angle selection on-screen.

• Display disappears after 5 seconds.

ANGLE

Press

or to select the desired angle.

repeatedly

Vocal Selection for Karaoke Discs (DVD only)

Press

AUDIO

to display the audio screen.

in Play mode

Press to select VOCAL and

press

AUDIO

select as shown below.

or to

Operation

DVD

ZOOM ANGLE

AUDIO SUB TITLE

Notes

• The subtitle cannot be enlarged or moved.

• During picture zoom, “ZOOM1” or “ZOOM2” appears on-screen for 5 seconds.

• Zooming, on some discs, may result in poor picture quality, or may not operate at all.

• DVD Karaoke (1 vocal) VOCAL ON VOCAL OFF

• DVD Karaoke (2 vocals) VOCAL V1 VOCAL V2 VOCAL V1+V2 VOCAL OFF

Picture Zoom (DVD only)

You can enlarge specific portions of a picture and select the zoom ratio using the ZOOM button during DVD playback.

Press

ZOOM

as follows.

• You can enlarge the center portion of the image to one of 2 magnifications.

■ Use the , , and buttons to move the position

up, down, left and right.

repeatedly to change display

Disc Operation (continued)

Title Menu (DVD only)

Some DVDs have more than one title, e.g. movies. If the disc offers a title menu, you can select the desired title number. (Operation may vary according to the disc.)

Press

TITLE

TI TLE MENU

Dogs

Lovers

Castles

in Play mode to display the title screen.

Birds

TI TLE MENU

Dogs

Love

Castles

Birds

of the world

Birds

Press or

NUMBER keys

to select a title, and

press

SET

PLAY

to start playing.

• “Pressing not necessary when using

NUMBER keys.

” is

DVD Menu (DVD only)

DVDs may offer a special menu. This menu may include guides to unique contents, audio/subtitle languages, etc. Although contents and operation may vary, the following steps show basic procedure for using the menu.

Press

DVD MENU

1 . SUBTI TLE

2 . AUDI O

3 . ANGLE

DVD MENU

1 . SUBTI TLE 2 . AUDI O

3 . ANGLE

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

in Play mode to display DVD MENU.

Press or

NUMBER keys

to select an item, and

press

SET

PLAY

to perform.

• Pressing not necessary when using

NUMBER keys.

Repeat step 2 if there is more than one menu.

SET

PLAY

NUMBER keys

CLEAR ACTION MENU

SELECT

SET PLAY

STOP

TITLE

PROGRAM PLAY

Important: if a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

Program Play (CD only)

You can program specific tracks and order of play.

Press

ACTION

to display DVD MAIN MENU.

DVD MAIN MENU

DI SC LANGUAGES AUDIO OUTPUT ST IL L MODE : AUTO TV MODE : 4 :3 Pan&Scan PROGRESSIVE OUT:

PLAY MODE

SELECT : SET : SET END : ACT ION

PROGRAM PLAY

RANDOM PLAY

PLAY MODE

Press

to select “PLAY MODE,” and

press

SET

to display.

Press

to select “PROGRAM PLAY,” and

SELECT : SET : SET END : ACT ION

PROGRAM PLAY

DI SC PROGRAM

1 61116 5 8

2 7 12 17 15 6 3 8 13 18 1 13 4 9 14 19 3 2 5101520 2

CLEAR LAST

CLEAR ALL START SELECT : SET : SET END : ACT ION

• Repeat step 4 to select another track.

• The selected track is added on the right side.

PROGRAM PLAY

DI SC PROGRAM

1 61116 5 8

2 7 12 17 15 6 3 8 13 18 1 13 4 91419 3 2 5101520 2

CLEAR LAST

CLEAR ALL START SELECT : SET : SET END : ACT ION

press

SET

to display.

Press

to select a track number (Track numbers on disc are displayed.), and

press

SET

Press

to select “START,” and

press

SET

to start play of programs in the sequence selected.

• To cancel, press during play, then press

CLEAR

STOP

Ready Checklist

DECK is in DVD mode, press DVD. CD is inserted.

Program Repeat Play (CD only)

Do operation steps 1 through 5

at left on this page.

Press

DISPLAY

Information screen.

(Disc Information Screen)

Press

DISPLAY

DECK Information screen.

Press

SET

Cursor move to “OFF.”

(DECK Information Screen)

Press to select “DISC.”

(DECK Information Screen)

to display Disc

to display

to enter Select mode.

Operation

DVD

Notes

• Up to 15 tracks can be programmed.

•“ ” or “ ” (depending on disc) indicates additional PROGRAM PLAY screen. Press for next or previous screen.

• To clear the last program one by one

Press to move to “CLEAR LAST” and press

SET

also clears last program.)

• To clear all programs

Press to move to “CLEAR ALL” and press

SET.

is turned off or the disc is removed.)

. (Pressing

(Programs are also cleared when the power

CLEAR

on remote control

Press

SET

Cursor moves to “REPEAT.”

to set mode.

To cancel, select “REPEAT : OFF” in step 5, then press

SET

Disc Operation (continued)

Random Play (CD only)

Tracks are played in a random order.

Press

ACTION

to display DVD MAIN MENU.

DVD MAI N MENU

DI SC LANGUAGES

AUDIO OUTPUT ST IL L MODE : AUTO TV MODE : 4 :3 Pan&Scan PROGRESSIVE OUT:

PLAY MODE

SELECT : SET : SET END : ACT ION

PLAY MODE

PROGRAM PLAY

RANDOM PLAY

SELECT : SET : SET END : ACT ION

Press

to select “PLAY MODE,”

and

press

to display.

Press

to select “RANDOM PLAY,” and

press

to begin random play.

• To cancel, press during play, then press

CLEAR

SET

STOP

Ready Checklist

DECK is in DVD mode, press DVD.

NUMBER keys

CLEAR ACTION

SELECT

SET

STOP VOLUME

ADJUST

DISPLAY

PAGE

Setting the VOLUME ADJUST (DVD only)

Some DVDs are recorded in lower than average volume levels. For these DVDs, this DECK can be set so that the average volume is increased automatically.

Press

VOL.ADJ

• “OFF” or “ON” lights up on Multi Function Display (about 3 seconds) when VOL.ADJ is pressed.

repeatedly to change “OFF”

VOLUME ADJUST “OFF”

Some DVD

[Low volume level]

Volume is at the original level.

• “ON” is set ..... When a DVD is played back, the average volume is increased.

• “OFF” is set .... The volume level recorded on the disc is played back just as it is.

Notes

• While settings can be made with all discs, they may have no effect with some discs. Please set as you prefer.

• When audio equipment is connected, setting the Sound Output level to “OFF” is recommended.

• If the sound becomes abnormal while playing a disc, set the Sound Output level to “OFF.”

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

↔↔

↔ “ON.”

↔↔

VOLUME ADJUST “ON”

Volume level is increased

when played back.

Important: if a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

DVD-Audio Operation (DVD-Audio only)

This DECK, equipped with a 192 kHz/ 24 bit Audio D/A converter, supports DVD-Audio recorded with high quality sound. The DVD-Audio feature includes “Still Image Skip” and “Bonus Group Playback” functions. (See below.) Please refer to “Basic DVD Operation” on pages 22 and 23.

Still Image Skip (DVD-Audio only)

DVD-Audio still images (only if contained) can be skipped over.

PAGE : 1

PAGE : 2

SELECT :

• Still Image Skip function not available with all discs.

Note

Bonus Group playback (DVD-Audio only)

Some DVD-Audio discs contain bonus groups. To enjoy these groups you may have to enter a password. Refer to the disc's jacket.

Press

Note

DISPLAY

• During playback, Bonus Group tracks cannot be selected.

Press PAGE

in Play or Pause mode to display the still image and page number.

Each press of PAGE changes page number as shown below.

• Pressing PAGE on the last page returns to PAGE 1.

Press PAGE Press PAGE

2 PAGE

3 ....... PAGE

Press PAGE

PAGE

Press PAGE

1 PAGE

in stop mode to display “On-Screen Displays.”

Operation

DVD

GROUP : 2 DVD-AUDIO TRACK : 1 00 : 12 :34

SELECT : SET : SET NEXT : DI SPLAY

Notes

• If the proper secret code is already entered, Bonus Group tracks can be selected. (Secret code enter screen is skipped.)

BONUS GROUP

ENTER 4

• When the proper secret code has been entered, Bonus Group track 1 playback

Note

begins. If a mistake is made, the secret code enter screen is redisplayed.

Press

-DIGITCODE

----

CLEAR

Press Press number, and press

Press

to select “GROUP,” and press

NUMBER keys

SET

NUMBER keys

to enter bonus group secret code.

To Make Corrections Press Press

repeatedly to move the cursor.

NUMBER keys

to make the correction.

to return to normal screen.

to select bonus group

(see pp. 44, 45.)

SET

DVD-RAM Operation (DVD-RAM only)

You can enjoy playing your personally recorded/edited DVD-RAM discs on this DECK.

Note

• This DECK was designed for playback only. DVD-RAM recording is not possible.

Play a DVD-RAM

Do steps 1 ~ 3 on page 22.

• Play begins from the first program title recorded on the DVD-RAM.

Press

Navigator or Play List menu for easy title or scene selection.

• See below for “Direct Navigator” or next page for “Play List information”.

Press

D.NAVI*

Press

STOP

OPEN/CLOSE

3 4

PLAY LIST

to stop playing.

to eject the disc.

to display Direct

Direct Navigator

If the DVD-RAM features Direct Navigator, a list of recorded titles is displayed. Simply select a title number and start playback. (Operation can vary with disc used.)

Press

D.NAVI

in Play/Stop mode to display the Direct Navigator

menu. Press to select a page and press to

select a title (Program No.).

Then, press

• “Pressing SET or PLAY” is not necessary when using NUMBER keys.

Using NUMBER keys starts playing automatically.

The number of available titles varies with each disc.

<Input

Example>

Press

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

SET

PLAY

to start playing.

1 digit number 1 ••••1 2 digit number 12 ••• 10 ➛ 1 ➛ 2

D.NAVI

to clear Direct navigator menu.

Program No.

Direct Navigator

No. Date Length Title

SELECT: SET : SET END:TITLE

Recording time and date

2002/12/24 5:15:41AM

2002/12/25 4:31:49AM

2002/12/25 8:24:25AM

2002/12/25

12:45:00AM

Recording time length

Drama

00:01:00

Pana NEWS

00:03:12

Tigers vs.Giants

00:15:01

Dinosaur

00:03:00

Titles

(Example)

Page No.

Page 1/4

Important: if a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

Play List

If the DVD-RAM features a Play List, your preselected list of favorite scenes is displayed for easy access. (Operation can vary according to how you edited the DVD-RAM.)

Press

PLAY LIST

in Play/Stop mode to display the Play List menu.

Press to select a page and press to

select a title (Play List No.).

Then, press

SET

PLAY

to start playing.

• “Pressing SET or PLAY” is not necessary when using NUMBER keys.

Using NUMBER keys starts playing automatically.

The number of available titles varies with each disc.

<Input

Example>

Press

PLAY LIST

1 digit number 1 ••••1 2 digit number 12 ••• 10 ➛ 1 ➛ 2

to clear Play List menu.

NUMBER keys

SELECT

Play List No.

Play List

No.

SELECT: SET :SET

and date

PLAY LIST

Date

2002/12/24

5:15:41AM

2002/12/25

4:31:49AM

2002/12/25

8:24:25AM

2002/12/25

12:45:00AM

Established time length

Title

Length

Movie Picture

00:01:00

Playback Still Picture

00:03:12

Playback Hybrid Playback

00:15:01

Partial Playback

00:03:00

END:MENU

TitlesRecording time

(Example)

Page No.

Page 1/5

Operation

DVD

SET

STOP

PLAY

D.NAVI

Notes

• Titles of Direct Navigator and Play List cannot be changed using this DECK.

• With Direct Navigator, up to 99 programs can be displayed. With Play List, up to 99 titles (999 scenes) can be displayed.

• While DVD MAIN MENU is displayed, Direct Navigator and Play List display will not appear even if TITLE or MENU is pressed.

• When appears on the screen while a button is being operated, it means that the corresponding operation is prohibited by DECK or the disc.

DVD Operation using On-Screen Displays

When

DISPLAY

information (title/chapter/track number, elapsed playing time) and DECK information (repeat play, play mode).

Press

to display “On-Screen Displays.”

• Each press of

display as follows. (Refer to pp. 44 ~ 48.)

➡

is pressed, On-Screen Displays show disc

DISPLAY*

Selected Disc information

in Play or Stop mode

DISPLAY

➡

changes the on-screen

(See pp. 45, 46.)

Ready Checklist

DECK is in DVD mode, press DVD.

Selected DECK information

Note

•

DISPLAY

DVD, title menu of DVD, Direct Navigator or Play List is displayed.

button does not function while main menu of

Press (or ) to select an item, and

SET

press

Press or to select the setting, and press

➡

Normal Screen

NUMBER keys

• When numbers are

• If the number entered is

• For more details, refer to

(See pp. 47, 48.)

SET

displayed (e.g. title number), are also available.

not on the disc, the entry will have no effect. Re-enter the correct number.

the disc operation information.

To return to normal screen, press

repeatedly.

NUMBER keys

DISPLAY

NUMBER keys

SELECT

SET

DISPLAY

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Note

• When appears on the screen while a button is being operated, it means that the corresponding operation is prohibited by DECK or the disc.

Important: if a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

Detailed Descriptions of each On-Screen Display

■■

■ Disc information screen (for DVD-Video)

■■

1. TITLE No.

Go directly to a preset title number.

• Select “TITLE”, and press

• Change the No. by pressing or

2. CHAPTER No.

Go directly to a preset chapter number.

• Select “CHAPTER”, and press

• Change the No. by pressing or

• This function does not work with some discs.

3. Disc currently being played

The type of disc currently inserted is displayed.

4. Elapsed playing time

The screen may be changed by selecting the elapsed time.

• Select the elapsed playing time (“xx:xx:xx”), and press

• Change the elapsed time by pressing

Enter time starting with seconds. If the time entered is not on the disc, the entry will have no effect. Re-enter the correct time. e.g., press 0 ➛ 1 ➛ 2 ➛ 3 ➛ 4 ➛ 5 ➛ SET for “01 : 23 : 45”.

press 3 ➛ 0 ➛ SET for “00 : 00 : 30”.

• This function does not work with some discs.

SET

NUMBER keys

, and press

SET

1 2

3 4

■■

■ Disc information screen (for DVD-Audio)

■■

A.GROUP No.

Go directly to a preset group number.

• Select “GROUP”, and press

• Change the No. by pressing or

SET

NUMBER keys

, and press

B.TRACK No.

Go directly to a preset track number.

• Select “TRACK”, and press

• Change the No. by pressing or

SET

NUMBER keys

, and press

C.Disc currently being played

The type of disc currently inserted is displayed.

D.Elapsed playing time

The screen may be changed by selecting the elapsed time.

• Select the elapsed playing time (“xx:xx:xx”), and press

• Change the elapsed time by pressing

press 3 ➛ 0 ➛ SET for “00 : 00 : 30”.

• This function does not work with some discs.

NUMBER keys

SET

Operation

DVD

A B

C D

DVD Operation using On-Screen Displays (continued)

■■

■ Disc information screen (for CD)

■■

1. TRACK No.

Go directly to a preset track number.

• Select “TRACK”, and press

• Change the No. by pressing or

SET*

NUMBER keys

, and press

2. Disc currently being played

The type of disc currently inserted is displayed.

3. Elapsed playing time

■■

■ Disc information screen (for DVD-RAM)

■■

A.Direct Navigation (PROGRAM) or PLAY LIST No.

Go directly to a preset title number.

• Select “PROGRAM” or “PLAY LIST”, and press

• Change the No. by pressing or

NUMBER keys

SET

, and press

B.Disc currently being played

The type of disc currently inserted is displayed.

C.Elapsed playing time

The screen may be changed by selecting the elapsed time.

• Select the elapsed playing time (“xx:xx:xx”), and press

• Change the elapsed time by pressing

press 3 ➛ 0 ➛ SET for “00 : 00 : 30”.

• This function does not work with some discs.

NUMBER keys

SET

Direct Navigation

(PROGRAM)

PLAY LIST

2 3

Note

• When appears on the screen while a button is being operated, it means that the corresponding operation is prohibited by DECK or the disc.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Important: if a remote control button does not work when pressed,

■■

■ DECK information screen (for DECK)

■■

press the DVD button on the remote and try the button again.

. Operating mode

The current operation is displayed.

. Repeat Play mode (see p. 48)

1 2

Repeat play mode can be selected.

• Select “REPEAT”, and press

• Change the desired mode during play by pressing , and press

DVD-Video CHAPTER TITLE OFF (NORMAL) DVD-Audio TRACK GROUP OFF (NORMAL) DVD-RAM (PROGRAM) PROGRAM DISC OFF (NORMAL)

(PLAY LIST) PLAY LIST ALL PLAY LIST OFF (NORMAL)

CD TRACK DISC OFF (NORMAL)

. Play mode [CD only] (See p. 39, 40.)

SET

Repeat Play mode

When Play mode is set (p. 39, 40), the mode name is displayed.

PROGRAM PLAY program play RANDOM PLAY random play

----

• For repeat play in VCR mode, see p. 31.

Note

normal play

SET

Operation

DVD

NUMBER keys

SELECT

SET

DVD Operation using On-Screen Displays (continued)

For your reference

Repeat Play mode example (see p. 47)

• CHAPTER/TITLE REPEAT PLAY (DVD-Video)

CURRENT PLAYBACK POSITION

TITLE

chapter

CHAPTER REPEAT

TITLE REPEAT

NORMAL PLAY

chapter

• TRACK/GROUP REPEAT PLAY (DVD-Audio)

CURRENT PLAYBACK POSITION

TRACK REPEAT

GROUP REPEAT

NORMAL PLAY

GROUP

track

GROUP

track

• TRACK/DISC REPEAT PLAY (CD)

CURRENT PLAYBACK POSITION

track

TRACK REPEAT

DISC REPEAT

NORMAL PLAY

chapter

track

POWER OPEN/

NUMBER keys

ACTION SELECT

SET PLAY

STOP SKIP+ SKIP

FF REW PAUSE

• PROGRAM/DISC REPEAT PLAY (DVD-RAM [PROGRAM])

CURRENT PLAYBACK POSITION

PROGRAM

PROGRAM REPEAT

DISC REPEAT

NORMAL PLAY

PROGRAM

• PLAY LIST/ALL PLAY LIST REPEAT PLAY (DVD-RAM [PLAY LIST])

CURRENT PLAYBACK POSITION

PLAY LIST

PLAY LIST REPEAT

ALL PLAY LIST REPEAT

NORMAL PLAY

• For repeat play in VCR mode, see p. 31.

Note

Important: if a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

PLAY LIST

MP3/WMA/JPEG Playback Operation

This unit can play MP3/WMA/JPEG format CD-R or CD-RW recorded for personal use on a PC, etc. Some discs may not play due to the condition of the recording.

Press

1 2

POWER

Press

OPEN/CLOSE

then place an MP3/WMA/JPEG disc into

* on the remote or DECK.

the disc tray.

Press

OPEN/CLOSE

• MP3/WMA/JPEG MENU is displayed.

• Playback starts automatically

(except JPEG files).

• CD directory is displayed.

Function

Status

Folder area

(Current folder

appears green.)

:MP3 file :WMA file

:Folder :Parent folder :JPEG file

ROOT

END_W

ALTZ

DD_CUB I C

CTURNE

TECHNO

POPS

AZZ

• Select file (During STOP mode)

1)Press to select an MP3/WMA file ( / ).

➡ MP3/WMA Playback (see right)

2)Press to select a JPEG file ( ).

➡ JPEG Playback (see p. 50)

3)Press

(previous) to skip a file/folder page (7 files) in the File area.

• Select folder (During STOP mode)

1)Press to select a folder ( ).

2)Press

in the folder.

• Select parent folder (During STOP mode)

1)Press to select a folder ( ).

2)Press

directory display.

Press

MENU. (➛ Press

STOP

ROOT

TECHNO DD

POPS J

AZZ

PLAY MODE : NORMAL

PLAY MODE

(Diagram left shows CD directory structure as displayed in example OSD above.)

Notes

• Only File (not Folder) area operation is possible.

• Files are displayed in the following order:

(!...0,1....9,A,B......Z).

SKIP+

SET

to display files/folders contained

SET

to make changes to the previous

ACTION

to close.

. .

END_W

ALTZ

CUB I C NOCTURNE NORN

| (next) or

Parent folder

File area

(Selected file/ folder is highlighted. Titles are displayed up to 11 characters.)

SKIP-

to return the DVD MAIN

ACTION

again to return

to the MP3/WMA/JPEG MENU.)

MP3/WMA Playback

Do steps 1~3 at left.

Press to select an MP3/WMA file ( / ).

(During STOP mode)

Press

SET

PLAY

■ Forward/Reverse Search Press

FF/SLOW+

Press

PLAY

• Search speed, slow at first, increases with each

additional press of the button up to 5 levels.

■ Forward/Reverse Track Skip Press

Each press skips a track.

• If pressed within first 3 seconds of playback,

skips to the previous track. If over 3 seconds, returns to top of track. (

• Put DECK in Stop mode before performing

folder/file selection (see step 4.)

■ Pause Press Press

Press

The MP3/WMA/JPEG MENU is closed

automatically.

Note

• Copyright protected files and files

containing errors cannot be played back. The DECK skips to the next file.

■ Select PLAY MODE [MP3/WMA Playback]

(During STOP mode) Press to select the desired PLAY MODE (see below).

[PLAY MODE] NORMAL:

All MP3/WMA files are selected and played back one time only.

SINGLE REPEAT:

The selected MP3/WMA file is played back repeatedly.

FOLDER REPEAT:

The MP3/WMA files contained in the selected folder are played back repeatedly. However, folders below the selected folder are not played back.

DISC REPEAT:

All MP3/WMA files are played back repeatedly.

to release.

SKIP+

PAUSE PLAY

to release.

STOP

OPEN/CLOSE

to start playback.

REW/SLOW-

| or

SKIP-

during play.

to stop play.

during play.

| during play.

| only.)

to eject the disc.

Operation

DVD

MP3/WMA/JPEG Playback Operation (continued)

JPEG Playback

You can play back JPEG images. Displayable Image Size: 32x32~7680x7680 pixels

• Some JPEG format may not be played

Note

Do steps 1~3 on page 49.

■ Returned on the MP3/WMA/JPEG MENU

■ Next/Previous Search

■ Start Slide-show ➡ Press

■ Enlarging an image ➡ Press

■ Rotating an image ➡ Press

back.

Press to select a JPEG file ( ).

Press

SET

PLAY

Selected JPEG file is displayed.

[JPEG Playback Screen]

➡ Press

REW/SLOW-

Press

JPEG MENU.

STOP

. (See p. 49)

SKIP+

STOP

| or

SKIP-

. (below)

to return to the MP3/WMA/

| .

FF/SLOW+

ZOOM

ANGLE

. (P. 51) . (P. 51)

■ Select PLAY MODE [JPEG Slide-show]

(During STOP mode) Press to select the desired PLAY MODE (See below).

[PLAY MODE]

NORMAL:

All JPEG files are selected and played back one time only.

SINGLE REPEAT:

The selected JPEG file is played back repeatedly.

FOLDER REPEAT:

The JPEG files contained in the selected folder are played back repeatedly. However, folders below the selected folder are not played back.

DISC REPEAT:

All JPEG files are played back repeatedly.

JPEG Slide-show

(During JPEG Playback.)

JPEG files are displayed automatically (about every 3 seconds) as a slide-show.

Press

Image changes every 3 seconds.

■ Cancel slide show

■ Still picture

■ Forward/Reverse File Skip

FF/SLOW+

➡ Press

➡ Press ➡ Press

➡ Press

Press

the DVD MAIN MENU.

STOP

JPEG MENU. (See p. 49)

STILL

PLAY

SKIP+

Each press skips a file.

ACTION

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

REW/SLOW-

to return the MP3/WMA/

(only SLIDE).

to release.

| or

SKIP-

| .

to return to

Operation can be done when files are in order, such as in the diagram below.

ROOT

01 PIC

REW/SLOW-

FF/SLOW+

AAA DDD TTT UUU VVV WWW ZZZ

REW/SLOW-

FF/SLOW+

SELECT

SET FF/

SLOW+ REW/

SLOWSTILL

ANGLE

ACTION

STOP

PLAY

SKIP+ SKIP

ZOOM

1st press

JPEG Zoom

(During JPEG Playback.)

You can enlarge specific portions of a JPEG picture and select the zoom ratio using the ZOOM button on the remote during JPEG Playback screen.

Set Zoom size.

Press

ZOOM

follows.

Press

➡

• You can enlarge the center portion of the image to one of 2 magnifications.

• Operation can be done during Rotation (below).

X 1.0 (ORIGINAL)

■ Use the , , and buttons to move the

position up, down, left and right. (Position cannot be changed on X1.0 ORIGINAL images.)

repeatedly to change display as

STOP

to return the MP3/WMA/JPEG MENU.

X 1.5 (ZOOM 1) X 2.0 (ZOOM 2)

1st press

2nd press

3rd press

JPEG Rotation

(During JPEG Playback.)

You can rotate a JPEG picture using the ANGLE button on the remote during JPEG Playback screen. (The JPEG picture will be rotated 90 ° clockwise.)

Set rotation.

Press

ANGLE

as below.

Press

➡

• Operation can be done during Zoom (above).

• The vertical/horizontal ratio of rotated JPEG images may vary when they are displayed.

2nd press 3rd press

repeatedly to change display

STOP

to return the MP3/WMA/JPEG MENU.

Operation

DVD

MPEG Layer-3 audio decoding technology licensed from Fraunhofer IIS and Thomson multimedia.

Windows Media, and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States and/or other countries. WMA is a compression format developed by Microsoft Corporation. It achieves the same sound quality as MP3 with a file size that is smaller than that of MP3.

4th press

Settings for DVD Operation

Press

ACTION

to display DVD MAIN MENU.

DVD MAIN MENU

DI SC LANGUAGES

AUDIO OUTPUT ST IL L MODE : TV MODE : 4 :3 Pan&Scan PRO

GRESSIVE OUT: OFF

SELECT : SET : SET END : ACT ION

AUTO

Press

to select an item, and

press

SET

DISC LANGUAGES (See below)

All languages offered on the disc can be set. If a language not offered is set, the original disc language will be selected.

AUDIO OUTPUT (See p. 53.)

You can set the audio output that comes from the digital audio output terminal.

STILL MODE (See p. 54.)

To select “FIELD” (Field still) or “FRAME” (Frame still) to prevent jitter or make small text or fine patterns clearly visible in a still picture. When “AUTO” is set, “FIELD” or “FRAME” is selected automatically.

TV MODE (See p. 54.)

To select whether the video material for a widescreen will be played back in the Pan & Scan style, Letterbox style or 16 : 9 style.

Disc Languages (DVD only)

To select and set the language of the audio soundtrack, subtitles, or title/DVD menus for all discs to be played.

DVD MAIN MENU

DI SC LANGUAGES

AUDIO OUTPUT

ST IL L MODE : TV MODE : 4 :3 Pan&Scan PRO

GRESSIVE OUT: OFF

SELECT : SET : SET END : ACT ION

AUDI O : En g li s h

SUBT ITLE : AUTO

MENUS : English

SELECT : SET : SET END : ACT ION

Press

MENU and go to step 2 to setup another

AUTO

DI SC LANGUAGES

ACTION

item.

Or, press

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

ACTION

Press

to select “DISC LANGUAGES,” and

press

SET

to display screen.

Press

to select an item, and

press

SET

repeatedly for desired language. (Please refer right.)

to redisplay DVD MAIN

twice to exit.

Once initial settings are done, they remain in memory (even after power is turned off) until changed. This means DECK will operate under the same conditions (especially DVDs) each time.

Ready Checklist

DECK is in DVD mode, press DVD.

NUMBER keys

ACTION

SELECT

SET

“AUDIO” selections

(Factory preset: English)

To select the audio soundtrack language.

English/Spanish/French/Japanese Original: Original disc language

OTHER 0000: Other language selection*

“SUBTITLE” selections

(Factory preset: AUTO)

To select the subtitle language.

AUTO: Same language selected

for “AUDIO”

• If language set for “AUDIO” is used in

playback, subtitles will not appear.

• If another language is used during

playback, the subtitles will appear in the language selected at “AUDIO” setup.

English/Spanish/French/Japanese OTHER 0000: Other language selection*

“MENUS” selections

(factory preset: English) To select the language used in title menus or DVD menus.

English/Spanish/French/Japanese OTHER 0000: Other language selection*

To enter OTHER ✱✱✱✱

Press

NUMBER keys

language codes on p. 56). To make corrections, press repeatedly to delete language code number, and correct.

*1If the selected language is not offered,

the original disc language is selected.

code number,

(Please refer to

*Important: If a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

Audio Output (DVD only)

Select the digital output to be output from the optical digital audio output connector of DECK.

ACTION

Press

to display DVD MAIN MENU.

DVD MAI N MENU

DI SC LANGUAGES

AUDIO OUTPUT

ST IL L MODE : TV MODE : 4 :3 Pan&Scan PRO

GRESSIVE OUT: OFF

SELECT : SET : SET END : ACT ION

LPCM(DVD) : OFF

Dolby Digital : Bitstream dts : Bitstream DRC : OFF

SELECT : SET : SET END : ACT ION

■■

■ “LPCM (DVD)” selections

■■

OFF: Linear PCM of less than 44.1 or 48 kHz/16 bit

is output. When playing DVDs recorded in linear PCM of over 44.1 or 48 kHz/20 bit, no digital audio is output. (Factory preset)

PCM: When playing DVDs recorded in linear PCM of

44.1 or 48 kHz/20 bit/24 bit or more, digital audio converted to 44.1 kHz/16 bit or 48 kHz/ 16 bit is output. (Digital output of PCM audio is restricted to 48 kHz/16 bit or below for copyright protection.)

■■

■ “Dolby Digital” selections

■■

Bitstream: Dolby Digital bitstream (1 ch - 5.1 ch)

PCM: When you have connected an amplifier that

doesn’t have a built-in Dolby Digital decoder.

■■

■ “dts” selections

■■

Bitstream: DTS bitstream is output. (Factory preset) PCM: When you have connected an amplifier that

doesn’t have a built-in DTS decoder.

■■

■ “DRC (Dynamic Range Compression)”

■■

AUTO

AUDI O OUTPUT

is output. (Factory preset)

selections

OFF: Normal audio range is selected. (Factory preset) ON: For dynamic sound even at low volume,

this is useful for late-night listening. [Dolby Digital DVDs only].

Press

to select “AUDIO OUTPUT,” and

press

SET

to display screen.

Press

to select an item, and

press

SET

repeatedly for output. (See below.)

Ready Checklist

DECK is in DVD mode, press DVD.

Type of amplifier to be connected

No amplifier is connected AV amplifier (with digital

audio input connector) without Dolby Digital/DTS decoder

AV amplifier including Dolby Digital decoder

AV amplifier including Dolby Digital/DTS decoder

• Make settings according to amplifier connected to optical audio output as shown in above table.

*1 When connecting an amplifier (with an

optical digital input connector) which does not contain the Dolby Digital or DTS decoder, be sure to select “PCM”. If “Bitstream” is selected, starting DVD play may cause such a high level of noise as to be harmful to your ears and damage the speakers.

*2 When a dts decoder is connected,

please select “Bitstream” in “dts.” If “PCM” is selected, there will be stereo sound. When a Dolby Digital decoder is connected, please select “Bitstream” in “Dolby Digital.” If “PCM” is selected, there will be stereo sound.

Recommended setting

PCM

Dolby Digital

PCM*

Bitstream

LPCM (DVD)

DTS

PCM*

PCM

Bitstream

Operation

DVD

Press

ACTION

MENU and go to step 2 to setup another

to redisplay DVD MAIN

item. Or, press

ACTION

twice to exit.

Settings for DVD Operation (continued)

Still Mode (DVD only)

Set to reduce jitter in a displayed still picture or a motion picture.

Press

ACTION

to display DVD MAIN MENU.

DVD MAI N MENU

DI SC LANGUAGES

AUDIO OUTPUT

ST IL L MODE :

TV MODE : 4 :3 Pan&Scan PRO

GRESSIVE OUT: OFF

SELECT : SET : SET END : ACT ION

AUTO: “FIELD” (Field still) or “FRAME” (Frame still) is

FIELD: “FIELD” (Field still) is always selected.

FRAME:“FRAME” (Frame still) is always selected.

Press

to exit this mode.

AUTO

automatically selected during the still mode. (Factory preset)

This setting will reduce jitter when compared with “AUTO” on some discs.

Some texts and fine patterns will be seen clearly when compared with “AUTO” on some discs.

ACTION

Press

to select “STILL MODE,” and

SET

press

repeatedly

for mode. (See below.)

TV Mode (DVD only)

Set the screen display style for wide-screen video material playback.

Press

ACTION

to display DVD MAIN MENU.

DVD MAI N MENU

DI SC LANGUAGES

AUDIO OUTPUT ST IL L MODE :

TV MODE : 4 :3 Pan&Scan

PRO

GRESSIVE OUT: OFF

SELECT : SET : SET END : ACT ION

4:3 Pan & Scan (Factory preset) :

Wide-screen video data is played in Pan & Scan style (left and right of screen is trimmed.)

• Video data not formatted in Pan & Scan will play in letterbox style.

4:3 Letterbox :

Wide-screen video data is played in Letterbox style (top and bottom of screen has black margin).

16:9 :

Set “16:9” when using Wide-screen TV.

AUTO

Press

to select “TV MODE,” and press

SET

repeatedly for mode. (See below.)

ACTION SELECT

SET

Example

• Pan & Scan (Factory preset)

• Letterbox

Press

to exit this mode.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

ACTION

*Important: If a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

PROGRESSIVE OUT

Sets the Component Video Output Connector (p. 10, 13) to output the Progressive scan signal.

ACTION

Press

to display DVD MAIN MENU.

DVD MAI N MENU

DI SC LANGUAGES

AUDIO OUTPUT ST IL L MODE : TV MODE : 4 :3 Pan&Scan

PRO

GRESSIVE OUT: OFF

SELECT : SET : SET END : ACT ION

OFF: Progressive scan signal is not output. ON: Progressive scan signal is output from the

Press

to exit this mode.

AUTO

Component Video Output Connector.

ACTION

Press to select

“PROGRESSIVE OUT,” and

press

SET

repeatedly

for mode. (See below.)

A/V OPTIMIZER

You can set to preset audio/video effects as desired.

NORMAL

Press

A/V OPTIMIZER

in Play mode to display the A/V OPTIMIZER selection on-screen.

• Display disappears after 5 seconds.

Notes

• CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED TO SET PROGRESSIVE OUT TO “OFF”. IF THERE ARE QUESTIONS REGARDING OUR TV SET COMPATIBILITY WITH THIS MODEL 525p DVD/VCR DECK, PLEASE CONTACT OUR CUSTOMER SERVICE CENTER.

ACTION SELECT

SET

Operation

DVD

CI NEMA

Press

A/V OPTIMIZER

to select the desired mode below.

NORMAL CINEMA

ACTION

The video/audio effect of each mode is listed below.

Mode Video Audio

NORMAL

CINEMA

DRAMA

ACTION

Standard video Bright areas are subdued.

Standard video

Brightness and sharpness are enhanced.

DRAMA

Standard audio Enhances high/low range for

dynamic sound. Reduces high/low range so dialog

and vocals can be heard clearly. Enhances high/low range for

dynamic sound.

Note

• With some discs, the audio/video effect may not be obtained, also the audio/video effects may not work well.

A/V OPTIMIZER

Language Code List

Enter the appropriate code number for the initial settings “AUDIO”, “SUBTITLE” and/or “MENUS” (see p. 52).

Code Language

6565 Afar 6566 Abkhazian 6570 Afrikaans 6577 Ameharic 6582 Arabic 6583 Assamese 6588 Aymara 6590 Azerbaijani 6665 Bashkir 6669 Byelorussian 6671 Bulgarian 6672 Bihari

Bengali; Bangla

6678 6679 Tibetan 6682 Breton 6765 Catalan 6779 Corsican 6783 Czech 6789 Welsh 6865 Danish 6869 German 6890 Bhutani 6976 Greek 6978 English 6979 Esperanto 6983 Spanish 6984 Estonian 6985 Basque 7065 Persian 7073 Finnish 7074 Fiji

Code Language

7079 Faroese 7082 French 7089 Frisian 7165 Irish 7168 Scots Gaelic 7176 Galician 7178 Guarani 7185 Gujarati 7265 Hausa 7273 Hindi 7282 Croatian 7285 Hungarian 7289 Armenian 7365 Interlingua 7378 Indonesian 7383 Icelandic 7384 Italian 7387 Hebrew 7465 Japanese 7473 Yiddish 7487 Javanese 7565 Georgian 7575 Kazakh 7576 Greenlandic 7577 Cambodian 7578 Kannada 7579 Korean 7583 Kashmiri 7585 Kurdish 7589 Kirghiz 7665 Latin

Code Language

7678 Lingala 7679 Laothian 7684 Lithuanian

Latvian, Lettish

7686 7771 Malagasy 7773 Maori 7775 Macedonian 7776 Malayalam 7778 Mongolian 7779 Moldavian 7782 Marathi 7783 Malay 7784 Maltese 7789 Burmese 7865 Nauru 7869 Nepali 7876 Dutch 7879 Norwegian 7982 Oriya 8065 Panjabi 8076 Polish

Pashto, Pushto

8083 8084 Portuguese 8185 Quechua

Rhaeto-Romance

8277 8279 Romanian 8285 Russian 8365 Sanskrit 8368 Sindhi

Serbo-Croatian

8372 8373 Singhalese

Code Language

8375 Slovak 8376 Slovenian 8377 Samoan 8378 Shona 8379 Somali 8381 Albanian 8382 Serbian 8385 Sundanese 8386 Swedish 8387 Swahili 8465 Tamil 8469 Telugu 8471 Tajik 8472 Thai 8473 Tigrinya 8475 Turkmen 8476 Tagalog 8479 Tonga 8482 Turkish 8484 Tatar 8487 Twi 8575 Ukrainian 8582 Urdu 8590 Uzbek 8673 Vietnamese 8679 Volapük 8779 Wolof 8872 Xhosa 8979 Yoruba 9072 Chinese 9085 Zulu

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Warning and Instruction Displays

These displays will alert you to a missed operation or provide further instructions.

PLEASE SET CLOCK BY PRESSING ACTION KEY

PLEASE PREPARE FOR TIMER REC

CHECK CASSETTE RECORD TAB

NO CASSETTE

TO CANCEL TIMER REC HOLD DOWN STOP KEY FOR APPROX 3 SEC

VIDEO HEADS MAY NEED CLEANING PLEASE INSERTHEAD CLEANING CASSETTE OR REFER TO MANUAL

END : PLAY

VCR LOCK ACTIVATED

REMOTE CONTROL IS SET TO TV MODE USE VCR : VCR KEY USE DVD : DVD KEY PLEASE CHECK THE DISC, AND FOR STAINS OR

SCRATCHES ON DISC

THIS DISC MAY NOT BE PLAYED IN YOUR REGION

THIS TYPE OF DISC CANNOT BE PLAYED. PLEASE INSERT A DIFFERENT DISC

CANNOT PLAY THIS FILE

THIS FILE IS PROTECTED

CautionOSD

If you attempt to set or review a Timer Recording and the Clock is not set...

If the DECK is not in Stop mode, or cassette is not inserted, or cassette has no record tab, or tape is at its end 2 minutes before a Timer Recording is about to begin...

If you press REC on the remote control or DECK, and a cassette is inserted with no record tab...

If you press PLAY, FF, REW, or REC on the remote control or DECK without a cassette inserted...

If you press STOP or POWER during a Timer Recording... (visible in VCR mode only)

If head cleaning becomes necessary while playing back a tape...

If you press a function button other than STOP/ EJECT or POWER while DECK is in VCR Lock mode...

If you press an invalid key on the remote while in TV mode...

If you press PLAY, and DECK reads data from a stained or scratched disc in DVD mode.

Playback of a disc with different region number was attempted. Only discs marked region “1”, “ALL”, or those that include “1” are playable on this DECK.

An unusable disc is inserted in the unit, or the disc is not installed with label side up.

This file format cannot be played. (Appears during MP3/WMA/JPEG file playback)

This file is copyright protected and cannot be played back. (Playback is prohibited.) (WMA only)

Page

24 25

20 21

28 29 34

Information

For Your

Before Requesting Service

Check the following points if you are having trouble with your DECK.

Power

No power…

Power turns itself off...

Recording & Playback

TV program cannot be recorded...

Timer recording cannot be performed…

There is no playback picture, or the playback picture is noisy or contains streaks...

During special effects playback picture may contain some vertical jitter when using a TV with an Automatic Vertical Hold Control...

DECK cannot be controlled...

Remote Control

DECK cannot be remote controlled...

PROG buttons do not respond...

Solution

• Completely insert Power Plug into an AC outlet.

• Press POWER button on.

• Make sure power source is active.

• Auto power-off (shutoff) occurs after about 5 min. in DVD mode with no operation, or if there is no broadcast signal in TV or Playback mode. Turn the power back on. (pp. 23, 33)

Solution

• Check connections between DECK, external antenna, and TV.

• Check channel selections.

• Make sure your antenna system (CABLE or TV) is correctly set. (Channels [p. 18])

• Make sure cassette record tab is intact. (p. 6)

• Confirm that clock is set to current time and date.

• Make sure Cable/DSS box (if used) is left on and tuned to channel to be recorded.

• Set recording start/stop times correctly. (p. 24)

• Timer recording may not be performed or continued if a power interruption occurs before or during a Timer Recording, even after power is restored.

• Select channel 3 or 4 on TV to match VCR output channel (3 or 4) (p. 16) or select LINE.

• Set VCR/TV selector to “VCR.”

• Adjust TRACKING control in either direction. (p. 4)

• Try Head Cleaning. (p. 4)

• Set TV’s Vertical Hold Control to MANUAL, then adjust.

• Make sure DECK power is on.

• Check Remote batteries.

• Make sure VCR LOCK is set to off. (p. 32)

• Make sure Remote is in proper mode. (p. 28)

• Make sure Timer Recording is not in progress.

Solution

• Make sure DECK power is on.

• Make sure Remote is in VCR mode.

• Aim Remote Control directly at remote sensor on DECK. (p.9)

• Avoid any object blocking signal path.

• Check Remote batteries. (p. 4)

• Exposing DECK remote sensor to direct fluorescent or outdoor light may cause signal interference.

• PROG functions are not available in COMPONENT Video Output and S-VIDEO OUT. Set TV to either RF IN or VIDEO IN. (p. 10)

• Check Remote batteries. (p. 4)

• Press VCR or DVD button for DVD/VCR mode. (p. 28)

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

DVD/ CD

Play fails to start even when PLAY is pressed...

Picture is distorted during rapid advance or rapid reverse...

No Forward/Reverse Scene Search play...

Audio soundtrack and/or subtitle language is not the one selected at the initial settings...

No subtitles...

Alternative audio soundtrack (or subtitle) language cannot be selected...

Angle cannot be changed...

Solution

• This DECK cannot play discs other than DVDs and CDs.

• The disc may be dirty and require cleaning.

• The picture will be somewhat distorted at times: this is normal.

• Some discs may have sections which prohibit Forward/Reverse Scene Search. (p. 23)

• If the audio soundtrack and/or subtitle language

selected at DVD initial settings does not exist on the disc, it will not be accessible.

• Subtitles appear only when available on disc.

• “OFF” is selected at the changing subtitle language.

Select “ON” at the “Subtitle Languages” section (p. 36) to display the subtitles.

• Alternative language cannot be selected with discs

which do not contain more than one language.

• For some discs, alternative language cannot be

selected with the AUDIO or SUB TITLE button. Try selecting it from the DVD MAIN MENU if available.

• This function is dependent on software availability.

Even if disc has multiple angles, they may be recorded for specific scenes only (ANGLE indicator on DECK lights up). (p. 37)

Miscellaneous

Programs cannot be viewed on TV...

Video cassette cannot be inserted...

Video cassette ejects when a recording is started or the power is turned off for timer recording...

In Stop mode, the motor (CYLINDER) continues to rotate...

The disc cannot be removed..

Solution

• Make sure TV is tuned to VCR's output channel (3 or 4).

• Check connections between DECK, external antenna, and TV.

• Set VCR/TV selector to “TV.” (p. 21)

• Make sure proper signal source is selected.

• If the television is not progressive compatible, a progressive scan picture is not available. Connect the Video Output or S-Video Output connector (pp. 12, 13) and set PROGRESSIVE OUT to “OFF” in the DVD Main Menu. (p. 55)

• Insert the cassette with window side up; record tab facing you.

• Make sure cassette record tab is intact. (p. 6)

• To enable Quick play mechanism, the cylinder will rotate for about 3 minutes. This reduces response time from Stop to Play mode.

• First, unplug DECK. Then, prepare a rigid wire (e.g. an extended paper clip) and, applying moderate force, insert it straight into the hole at the base of the tray. The tray will eject a little. Now, pull the tray all the way out and remove the disc. (p. 9)

If you cannot resolve the problem, please call the Customer Call Center for product assistance at 1-800-211-PANA (7262). To locate an authorized servicenter, please call toll free 1-800-211-PANA (7262). or, contact us via the web at:http://www.panasonic.com/contactinfo

Information

For Your

Limited Warranty

PANASONIC CONSUMER ELECTRONICS COMPANY, DIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA One Panasonic Way Secaucus, New Jersey 07094

PANASONIC SALES COMPANY, DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO, INC., AVE. 65 de Infantería, Km. 9.5 San Gabriel Industrial Park Carolina, Puerto Rico 00985

Panasonic DVD/VCR Deck Limited Warranty

Limited Warranty Coverage

If your product does not work properly because of a defect in materials or workmanship, Panasonic Consumer Electronics Company or Panasonic Sales Company (collectively referred to as “the warrantor”) will, for the length of the period indicated on the chart below, which starts with the date of original purchase (“Limited Warranty period”), at its option either (a) repair your product with new or refurbished parts, or (b) replace it with a new or a refurbished product. The decision to repair or replace will be made by the warrantor.

Product or Part Name

DVD/VCR Deck

Rechargeable Batteries (in exchange for defective item)

During the “Labor” Limited Warranty period there will be no charge for labor. During the “Parts” warranty period, there will be no charge for parts. You must mail-in your product during the warranty period. If non-rechargeable batteries are included, they are not warranted. This Limited Warranty only applies to products purchased and serviced in the United States or Puerto Rico. This Limited Warranty is extended only to the original purchaser and only covers product purchased as new. A purchase receipt or other proof of original purchase date is required for Limited Warranty service.

Parts

One (1) Year

Ten (10) Days

Mail-In Service

For assistance in the continental U.S.A. in obtaining repairs please ship the product to:

For assistance in Puerto Rico call Panasonic Sales Company (787)-750-4300 or fax (787)-768-2910. When shipping the unit carefully pack and send it prepaid, adequately insured and preferably in the original

carton. Include a letter detailing the complaint and provide a day time phone number where you can be reached.

IF REPAIR IS NEEDED DURING THE LIMITED WARRANTY PERIOD THE PURCHASER WILL BE REQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE INDICATING DATE OF PURCHASE, AMOUNT PAID AND PLACE OF PURCHSE. CUSTOMER WILL BE CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF OF PURCHASE.

Panasonic Services Company Customer Servicenter Suite B 4900 George McVay Drive McAllen, TX 78503

Labor

Ninety (90) Days

Not Applicable

Limited Warranty Limits And Exclusions

This Limited Warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT COVER normal wear and tear or cosmetic damage. The Limited Warranty ALSO DOES NOT COVER damages which occurred in shipment, or failures which are caused by products not supplied by the warrantor, or failures which result from accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation, setup adjustments, misadjustment of consumer controls, improper maintenance, power line surge, lightning damage, modification, or commercial use (such as hotel, office, restaurant, or other business), rental use of the product, or service by anyone other than a Factory Servicenter or other Authorized Servicer, or damage that is attributable to acts of God.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY COVERAGE”. THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. (As examples, this excludes damages for lost time, cost of having someone remove

or re-install an installed unit if applicable, travel to and from the servicer, loss of or damage to media or images, data or other recorded content. The items listed are not exclusive, but are for illustration only.)

ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied Limited Warranty lasts, so the exclusions may not apply to you.

This Limited Warranty gives you specific legal rights and you may also have other rights which vary from state to state. If a problem with this product develops during or after the Limited Warranty period, you may contact your dealer or Servicenter. If the problem is not handled to your satisfaction, then write to the warrantor’s Consumer Affairs Department at the addresses listed for the warrantor.

PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY, ARE YOUR RESPONSIBILITY.

Customer Services Directory

Obtain Product Information and Operating Assistance; locate your nearest Dealer or Servicenter; purchase Parts and Accessories; or make Customer Service and Literature requests by visiting our Web Site at:

http://www.panasonic.com/support

or, contact us via the web at:

http://www.panasonic.com/contactinfo

You may also contact us directly at: 1-800-211-PANA (7262), Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7 pm, EST.

For hearing or speech impaired TTY users, TTY : 1-877-833-8855

Accessory Purchases

Purchase Parts, Accessories and Instruction Books online for all Panasonic Products by visiting our Web Site at:

http://www.pasc.panasonic.com

or, send your request by E-mail to:

npcparts@panasonic.com

You may also contact us directly at:

1-800-332-5368 (Phone) 1-800-237-9080 (Fax Only) (Monday - Friday 9 am to 8 pm, EST.)

Panasonic Services Company 20421 84th Avenue South, Kent, WA 98032 (We Accept Visa, MasterCard, Discover Card, American Express, and Personal Checks)

For hearing or speech impaired TTY users, TTY : 1-866-605-1277

Service in Puerto Rico

Matsushita Electric of Puerto Rico, Inc. Panasonic Sales Company

Factory Servicenter:

Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park,

Carolina, Puerto Rico 00985

Phone (787)750-4300 Fax (787)768-2910

As of October 2003

Information

For Your

Medidas de seguridad y precauciones importantes

PARA REDUCIR EL RIESGO DE GOLPES ELÉCTRICOS, INCENDIOS, HERIDAS O DAÑOS A ESTE PRODUCTO, LEA Y GUARDE TODAS LAS INSTRUCCIONES DE SEGURIDAD Y FUNCIONAMIENTO. TENGA EN CUENTA TODAS LAS ADVERTENCIAS INDICADAS EN EL MANUAL Y EN EL PRODUCTO.

1 PRECAUCIÓN CON LA FUENTE DE ALIMENTACIÓN

El equipo solo debe hacerse funcionar desde una fuente de a limentación que se indique en la unidad o en este manual. Si fuera necesario, haga revisar la fuente de alimentación de su hogar por parte de la Compañia de Suministro Eléctrico o por parte de su Distribuidor de Productos de Vídeo.

2 CONECTOR POLARIZADO O CON TOMA A TIERRA

Como característica de seguridad, este producto de vídeo viene equipado con un enchufe de cable de alimentación polarizado (solo una pata es más ancha que la otra), o con

un enchufe del tipo con toma a tierra de tres patas. PRECAUCIÓN CON EL ENCHUFE POLARIZADO Este enchufe sólo entrará en la toma en un sentido.

Si no pudiera introducir el enchufe a fondo, intente darle la vuelta. Si aún así no entrara, llame a un técnico electricista para que le instale una toma de red adecuada. No desactive esta función de seguridad manipulando el enchufe de ninguna manera.

PRECAUCIÓN CON ENCHUFES CON TOMA A TIERRA Este enchufe sólo entrará en una toma con conexión a tierra de

tres orificios. Si fuera necesario, que un técnico electricista le instale la toma de red adecuada. No desactive esta función de seguridad manipulando el enchufe de ninguna manera.

3 CABLE DE ALIMENTACIÓN

Asegúrese de que los cables de alimentación son dispuestos

de tal forma que no se apoye nada sobre ellos, no ruede

nada sobre ellos, o que estén en el paso de tráfico al

caminar. Si se utilizara un cable alargador, asegúrese de

que también disponga de un enchufe polarizado o con toma

a tierra y de que puede conectarse firmemente. Los cables

pelados, los enchufes averiados o hilos quebrados

constituyen un peligro y deben ser reemplazados por un

técnico cualificado del servicio técnico. Las tomas eléctricas

de la red general sobrecargadas y los cables de extensión

constituyen riesgos de incendio y han de evitarse en lo

posible.

4 NO BLOQUEE LOS ORIFICIOS DE VENTILACIÓN

Las aberturas de ventilación del mueble liberan el calor

generado durante el funcionamiento de la unidad. Si se

bloquearan, el calor acumulado dentro de la unidad podría

ocasionar fallos que pueden llevar a riesgos de incendio o

daños por calor en las cassettes utilizadas.

5 EVITE UBICACIONES MUY CALIENTES O SOMETIDA

A CAMBIOS BRUSCOS DE TEMPERATURA

No coloque la unidad encima o cerca de cual quier tipo de

calefactor o regulador, bajo la luz solar directa, dentro de

vehículos, etc… No traslade la unidad súbitamente entre

sitios con variaciones extremas de temparatura. Si la unidad

es llevada bruscamente de un sitio frío a otro cálido, la

humedad puede condensarse en la unidad y en la cinta.

6 PARA EVITAR LESIONES PERSONALES

• No coloque equipos no fijados en superficies inclinadas.

• No coloque esta unidad sobre ningún soporte que no esté firme, nivelado y que sea adecuadamente fuerte. La unidad podría caerse y producir graves lesiones a niños o adultos y dañarse la unidad misma.

• La combinación de aparato y carrito debe moverse con cuidado. Las paradas súbitas, una fuerza excesiva ya las superficies irregulares pueden ocasionar el vuelco de la combinación de aparato y carrito.

• Siga atentamente las instrucciones de funcionamiento y utilice los accesorios recomendados por el fabricante al hacer funcionar esta unidad o al conectaria a otros equipos.

INSTALACIÓN

1 CONEXIÓN SEGURA DE LA ANTENA Y DE LOS CABLES

Si se conectara una antena exterior o sistema de cable conectado al equido, el usuario deberá asegurarse de que la antena o el sistema de cable disponen de toma a tierra como forma de proporcinar protección contra la acumulación de cargas estábicas y saltos de corrientes. La sección 810 del Código Eléctrico Nacional, ANSI/NFPA 70 (en Canadá, la parte 1 del Código Eléctrico Canadiense) proporciona información con respecto a la conexión a tierra correcta del mástil y la estructura de soporte, conexión a tierra de los cables de bajada de antena a una unidad de descarga, tamaño de los conductores a tierra, ubicación de la unidad de descarga de antena, conexión de los electrodos a tierra y requisitos del electrodo de toma a tierra.

MANTENGA LA ANTENA LIBRE DE LÍNEAS O CIRCUITOS DE ALTO VOLTAJE

Un sistema de antena exterior deberá ser colocado bien alejado de líneas de alimentación, luz eléctrica o circuitos de alimentación para que nunca esté en contacto con tales fuentes de alimentación si se cayera. Al instalar una antena exterior, debe tenerse muchísimo cuidado para evitar las líneas de alimentación, circuitos u otras fuentes de alimentación ya que esto podría resultar mortal. Debido a los riesgos implicados en la instalación de una antena, tal operación debe dejarse a un profesional.

Si la unidad ha estado almacenada o es trasladada a una nueva ubicación, remítase primero a la sección de INSTALACIÓN de estas medidas de seguridad.

1 MANTENGA ESTA UNIDAD DE VÍDEO ALEJADA DEL AGUA O DE

HUMEDAD DE CUALQUIER TIPO

2 SI EL EQUIPO ES EXPUESTO A LA LLUVIA, HUMEDAD, O FUERTES

IMPACTOS, desenchufe la unidad y que sea revisada por un técnico cualificado

antes de volver a utilizarla.

3 DURANTE UNA TORMENTA ELÉCTRICA

Durante una tormenta con rayos, tanto en interiores como en el exterior, o antes de dejar la unidad sin utilizar durante largos períodos de tiempo, desconecte todos los equipos de la fuente de alimentación así como la antena y el sistema de cableado.

4 AL ENCHUFAR LA UNIDAD

•No exponga nunca la unidad a la lluvia o el agua. NO LA HAGA FUNCIONAR si se ha derramado líquido dentro de la unidad. Desenchufe la unida inmediatamente ya que sea revisada por un técnico. Pueden producirse incendios o sacudidas eléctricas derivadas de cortocircuitos eléctricos causados por el contacto de líquidos con el interior de la unidad.

• No deje caer ni introduzca ningún objeto por las aberturas de la unidad. Algunas piezas internas tienen un voltaje peligroso y el contacto con ellas puede producir sacudidas eléctricas o incendios.

•Evite colocar la unidad directamente encima o debajo del televisor, ya que esto prodría causar interferencias eléctricas. Mantenga cualquier tipo de imán alejados de equipos electrónicos.

5 UTILIZACIÓN DE ACCESORIOS

Utilice sólo accesorios recomendados por el fabricante para así evitar riesgos de incendio, sacudidas eléctricas y otros peligros.

6 LIMPIEZA DE LA UNIDAD

Desenchufe la unidad. Luego utilice un paño limpio y seco, sin tratamiento químico para quitar suavemente el polvo o suciedad. NO UTILICE productos de limpieza, aerosoles, o aire comprimido que pudieran causar un exceso de pulverización o introducirse en la unidad y ocasionar sacudidas eléctricas. Caulquier substancia, como cera, cinta adhesiva, etc., podría arruinar el acabado de la superficie. La exposición a substancias grasosas, áreas húmedas o polvorientas puede afectar de manera adversa a las piezas intemas.

1 EL USUARIO NO DEBE REALIZAR NINGUNA OPERACIÓN DE

SERVICIO TÉCNICO POR SÍ MISMO

Si, después de observar atentamente las detalladas instrucciones de funcionamiento, este producto de vídeo no funcionara correctamente, no intente abrir o extraer las tapas, o realizar cualquier ajuste no indicado en este manual. Desenchufe la unidad y llévela a un técnico cualificado de servicio técnico.

2 SI FUERAN NECESARIAS PIEZAS DE RECAMBIO

Asegúrese de que el técnico de servicio utiliza sólo piezas especificadas por el fabricante, o de las mismas características que las piezas originales. La utilización de subsitutos no autorizados puede ser causa de incendios, sacudidas eléctricas, u otros peligros.

3 QUE EL TÉCNICO DE SERVICIO TÉCNICO REALICE UNA

COMPROBACIÓN DE SEGURIDAD

Después de cualquier servicio o reparación de la unidad, solicite al técnico de servicio que realice una completa comprobación de seguridad tal como se describe en la literatura de servicio técnico del fabricante para asegurarse así que la unidad de vídeo se encuentra en condiciones de funcionamiento seguras.

INSTALACIÓN DE LA ANTENA EXTERIOR

CÓDIGOO ELÉCTRICO NEC-NATIONAL

EMPALMADOR DE CONEXIÓN A TIERRA

EQUIPO DE SERVICIO ELÉCTRICO

UTILIZACIÓN DE LA UNIDAD DE VÍDEO

SERVICIO

BAJADA DE ANTENA

UNIDAD DE DESCARGA DELA ANTENA (SECCIÓN S10-20 DEL NEC)

CONDUCTORES CONEXIÓN A TIERRA (SECCIÓN S10-20 DEL NEC)

EMPALMADOR DE CONEXIÓN A TIERRA

SISTEMA DE ELECTRODOS DE CONEXIÓN A TIERRA DEL SERVICIO ELÉCTRICO (ART, 250 DEL NEC, PARTE H)

PRECAUCIONES DE SEGURIDAD

PARA PREVENIR INCENDIOS O CHOQUES ELÉCTRICOS NO EXPONGA ESTE APARATO A LA LLUVIA O LA HUMEDAD.

PARA PREVENIR CHOQUES ELÉCTRICOS, ASEGURASE QUE LA CLAVIJA HAGA JUEGO CON EL ENCHUFE Y CONÉCTELO COMPLETAMENTE.

PRECAUCION

PELIGRO DE DESCARGA

ELECTRICA NO ABRIR

PRECAUCION: PARA EVITAR LA POSIBILIDAD DE UNA DESCARGA ELECTRICA NO DESMONTAR LA

CUBIERTA (O LA PARTE TRASERA). ESTE APARATO

NO PUEDE SER REPARADO POR EL PROPIETARIO.

PARA CUALQUIER TRABAJO DE SERVICIO SE

DEBE RECURRIR A UN TECNICO ESPECIALIZADO.

Este símbolo advierte al usuario de que hay voltaje sin aislamiento dentro de la unidad de suficiente magnitud como para ocasionar sacudidas eléctricas. Por lo tanto, resultará peligroso realizar cualquier tipo de contacto con toda pieza interna de la unidad.

Este símbolo alerta al usuario de que se ha incluido importante literatura sobre el funcionamiento y mantenimiento de esta unidad. Por tanto, debe leerse atentamente tal literatura a fin de evitar cualquier problema.

Advertencia FCC: Cualquier cambio o modificación no autorizado de este

equipo anulará la autorización al usuario para hacer funcionar la unidad.

FCC Warning: Any unauthorized changes or modifications to this

equipment would void the user’s authority to operate.

rápida consulta

Guía para

Spanish Quick Use Guide/ Guía para rápida consulta

AUTO CLOCK SET

INCOMPLETE

PLEASE SET CLOCK BY PRESSING

ACT

ON KEY

CONEXIONES/CONFIGURACION INICIAL (READY TO PLAY)

Para ajustar el idioma, canal yPara ajustar el idioma, canal y

Realice la conexión de la antena o TV por cable antes de enchufar el cable de CA.

El DVD/VCR iniciará automáticamente la fijación de los canales y del reloj al enchufar el cable de CA.

CONEXIONES

Para Ant/Cable

Conecte el cable de la antena al terminal IN

FROM ANT del DVD/VCR. Conecte el terminal OUT TO TV del DVD/VCR

a la entrada de la antena VHF/UHF del TV con

➛➛

➛ DVD/VCR

➛➛

➛ TV

➛➛

Televisor

el cable RF incluido.

Para Sistema Digital de Satelite (DSS)/ Convertidor de cable

Conecte la salida de convertidor de cable

al terminal IN FROM ANT. Conecte el terminal OUT TO TV del DVD/VCR

a la entrada de la antena VHF/UHF del TV con el cable RF incluido.

CONFIGURACION INICIAL

Encienda el TV y cambie al canal 3.

Enchufe el cable de CA.

El DVD/VCR se encenderá e iniciará las fijaciones de los canales y del reloj.

• Si no aparece la pantalla de abajo, compruebe la conexión del DVD/VCR-TV y si el canal del TV está a 3, intennte cambiando al canal 4.

• Para cambiar el canal de salida del DVD/VCR, consulte las instrucciones de “Canal de salida del VCR” (informaciones en inglés página 19).

Enchufe el cable de CA.

Televisor

VHF/UHF

Al usar cables coaxiales RF del tipo “tuerca”, apriételos solamente con los dedos. Un apriete excesivo puede dañar los terminales.

Las fijaciones se realizan automáticamente.

Cuando termina las fijaciones, aparecerá la siguiente pantalla.

DVD/VCR

VHF/UHF

➛➛

➛ DVD/VCR

➛➛

DVD/VCR

Terminal OUT TO TV

Terminal IN FROM ANT.

Terminal OUT TO TV

Terminal IN FROM ANT.

Entrada (IN) desde

ANT./CABLE

➛➛

➛ TV

➛➛

Estuche convertidor de TV por cable

Entrada (IN) desde ANT./CABLE

CH AUTO SET PROCEEDING

Al inicio, el idioma de la pantalla está fijado a inglés.

CANCEL : STOP

Para cambiar el idioma, seleccione la pantalla

AUTO CLOCK SET

PROCEEDING

CANCEL : STOP

Si está usanndo un convertidor de TV por cable y en su area hay un canal de Public Broadcast Station (PBS), ajuste su convertidor al canal PBS de su area. Si está usando un receptor DSS, este debe estar apagado.

MENU (informaciones en inglés página 18).

Nota

• Los botones de funciones no funcionan durante la configuración inicial.

• Para retirar un cassette durante el ajuste automático, presione EJECT en el control remoto o STOP dos veces en el aparato. En este caso, los ajustes de los canales y la hora se deben hacer manualmente. Para los ajustes seleccione la pantalla MENU (informaciones en inglés página 18).

• Dependiendo de las condiciones, el ajuste automático puede durar más de 30 minutos. En ese caso, presione STOP para detener el ajuste automático y realice los ajustes manualmente en la pantalla MENU.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Para solicitar ayuda, por favor llame al: 1-800-211-PANA(7262) o consúltenos a través de página web en:http: //www.panasonic.com/contactinfo

Si aparece en la pantalla “AUTO CLOCK SET IS INCOMPLETE (FIJACION AUTOMATICA DEL RELOJ ES INCOMPLETO)”, Ajuste el reloj como se describe a continuación.

AJUSTE MANUAL DEL RELOJ

Si la fijación ha sido incompleta.

Presione la tecla ACTION en el control remoto

para visualizar la pantalla del menú SET CLOCK.

Presione para seleccionar el mes y SET

para ajustar. De la misma forma, seleccione y ajuste la fecha, año, hora y DST (hora de verano).

Presione dos veces la tecla ACTION para

poner el RELOJ en marcha y salir.

SETCLOCK

1 / 1/2004

THU

-- -12:00

SETCLOCK

SUN

DST:ON

- -15:30 DST:ON

-----------------------

6 /20/2004

-----------------------

Operaciones básicas para la reproducción

Inserte un cassette,

• La alimentación del DECK se activa. Si Auto VCR/TV (consulte la página 32) está en “INACT (OFF)”, presione VCR/TV en el control remoto para el modo VCR.

Presione PLAY para reproducir el cassette.

• Si el cassette no tiene la lengüeta de prevención de grabación (página 6), se inicia la reproducción automáticamente.

Detalles especiales durante la grabación

Presione FF/SLOW+ o REW/SLOW- para

búsqueda de escenas hacia delante/ hacia atrás. Presione PLAY para liberar. Durante la búsqueda, cada vez que

presione FF o REW se cambia la velocidad: Presione PAUSE/STILL para imagen Fija

(Congelada).

Presione PLAY para liberar. Presione PAUSE/STILL en el modo de

imagen fija para imágenes cuadro a cuadro.

Presione PLAY para liberar. Presione FF/SLOW+ o REW/SLOW- en el

modo de imagen fija para cambiar la velocidad de las imágenes a cámara lenta.

Presione STOP para detener el cassette.

Rebobinado/Avance rápido

Presione REW/SLOW- o FF/SLOW+ en el

modo de parada para rebobinado/avance rápido del cassette.

• Rebobina una cinta T-120 en aproximadamente 1 minuto.

Presione EJECT en el control remoto, o STOP/EJECT en el DECK para expulsar el cassette.

Operaciones básicas para la grabación

Inserte el cassette con lengüeta de

protección de grabación (página 6).

• La alimentación del DECK se activa. Si Auto

VCR/TV (consulte la página 32) está en “INACT (OFF)”, presione VCR/TV en el control remoto para el modo VCR.

Presione CH / , o las teclas de números

para seleccionar el canal.

Presione SPEED para seleccionar la

velocidad de grabación (página 6)

• SP = Reproducción normal

• SLP = Reproducción extra larga

Presione REC para comenzar a grabar.

• Para eliminar escenas indeseadas, presione

PAUSE/STILL para hacer una pausa, y al presionar nuevamente continua la grabación.

• No podrá ver otro canal durante la

grabación.

Presione STOP para detener la grabación.

Programación fácil para la grabación con temporizador

Presione PROG

para visualizar la pantalla de Programacion.

P FE IN IC PARADACA VEL

-- --:-- --:--

ELEGI R : TERM

INAR

: PROG

FIJAR : SET

Orden para elegir

Ejemplo

Fecha de hoy

3) Ajustes los ítems restantes, presione SET para ajustar los tiempos de

INICIO/PARADA, CANAL o entrada de LINEA (página 35), y la velocidad de la cinta (SP, SLP). Luego presione para seleccionar. Presione PROG para finalizar PROGRAM.

P FE IN IC PARADACA VEL

1 13 2:00p 3:20p 02

-- --:-- --:--

FIJACION ES COMPLETO

CANCELAR : ADD/DLT ELEGI R : TERM

INAR

: PROG

FIJAR: SET

Grabación de un toque

Presione REC repetidamente para ajustar la

hora de grabación (30 min - 4 horas).

• La videograbadora termina la grabación a una hora programada.

Grabación normal

1) Presion .

2) Para ajustar la FECHA de

grabación, presione

para seleccionar: 1-31 = una vez, o DIARIO = a la misma hora de lunes a viernes, o SEMANA = a la misma hora cada semana.

/ Orden para elegir

SEMANAL

Presione

SLP

para seleccionar un número

que no está usando para

(SA)

SEMANAL

(LU)

ingresar mas programas y

presione SET

para ajustar. Luego repita el paso 2. O

Presione nuevamente PROG para salir.

0:30 1:00

1:302:003:004:00

68 9

SEMANAL

(DO)

DIARIO

rápida consulta

Guía para

Spanish Quick Use Guide/ Guía para rápida consulta

Operaciones básicas del DVD

Presione

aparato.

Presione

1) Presione

2) Ponga un disco en la bandeja de disco.

• Sujete el disco sin tocar ninguna de sus superficies, póngalo con el lado donde esté impreso el título hacia arriba, alinéelo con las guías y póngalo en su posición apropiada. Disco de 3” (8 cm) / Disco de 5” (12 cm)

Presione

La bandeja del disco se cierra automáticamente.

• Si está usando un DVD interactivo y aparece el menú de títulos (TITLE MENU), siga al paso 5.

Presione o las teclas numéricas para

seleccionar el artículo deseado.

Presione Si usa las teclas numéricas, la reproducción comienza automáticamente.

Presione

■ Para buscar una escena particular Búsqueda hacia adelante

Presione

Búsqueda hacia atrás

Presione (Para liberar, presione

■ Para saltar un capítulo o una pista Salto hacia adelante

Presione

Salto hacia atrás

Presione l

■■

■ Para ver una imagen fija

■■

Presione (Para liberar, presione

■ Para ver imágenes cuadro a cuadro (DVD) Presione

La imagen avanza un cuadro cada vez que presiona la tecla. (Para volver a la reproducción normal, presione

■ Para ver en cámara lenta (DVD) Presione

de imagen fija. (Para liberar, presione

POWER

DVD

PLAY

SETo PLAY

STOP

OPEN/CLOSE

FF/SLOW+

REW/SLOW-

SKIP

PAUSE/STILL

en el control remoto o el

para seleccionar el modo DVD.

OPEN/CLOSE

para iniciar la reproducción.

para la reproducción.

para parar la reproducción.

para expulsar el disco.

en el modo de reproducción.

PLAY

)

l en el modo de reproducción.

SKIP

en el modo de reproducción.

durante la reproducción.

PLAY

)

en el modo de imagen fija.

FF/SLOW+oREW/SLOW-

PLAY

)

PLAY

)

en el modo

Funcionnamiento del DVD utilizando visualizaciones en pantalla

Cuando se presiona DISPLAY, la visualización en pantalla muestra la información del disco (título / capítulo / número de lista, tiempo transcurrido de reproducción, audio / idioma del subtítulo, y ángulo) e información (repetir la reproducción, modo reproducción, Karaoke vocal encendido / apagado, etc.).

Presione

o parada para visualizar las visualizaciones en pantalla.

• Cada vez que se presione

visualización en pantalla cambia como se muestra a continuación.

Presione (o ) para seleccionar el ítem

deseado.

Presione

Presione para seleccionar el ajuste

deseado.

Presione Para volver a la pantalla normal, Presione repetidamente

DISPLAY

Información seleccionada del disco

Información seleccionada del DECK

en el modo reproducción

DISPLAY

➡

,la

Pantalla normal

SET

para ajustar.

SET

para ajustar.

CLEARoDISPLAY

T ITULO : 12 DVD

CAPI TULO: 11 00: 12 :34

ELEGI R: FI JAR : SET SI GUI ENTE: DI SPLAY

T ITULO : 12 DVD

CAPI TULO: 11 00: 12 :34

ELEGI R: FI JAR : SET SI GUI ENTE: DI SPLAY

GRUPO

: 1 DVD-AUDIO

P I STA

: 1 00: 12 :34

T ITULO : 12 DVD CAPI TULO: 24 00: 12 :34

ELEGI R: 0-9 FI JAR : SET SI GUI ENTE: DI SPLAY

T ITULO : 12 DVD CAPI TULO: 24 00: 12 :34

ELEGI R: FI JAR : SET SI GUI ENTE: DI SPLAY

GRUPO

: 1 DVD-AUDIO

P I STA

: 1 00:12:34

ELEGI R:

TERMINAR

FI JAR : SET

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Para solicitar ayuda, por favor llame al: 1-800-211-PANA(7262) o consúltenos a través de página web en:http: //www.panasonic.com/contactinfo

: DISPLAY

ENTRAR: 0 FI JAR : SET

-9 TERMINAR

: DISPLAY

Fijaciones iniciales

Presione DVD para seleccionar el modo DVD.

Presione ACTION en el modo de parada para

visualizar MENU.

Presione para seleccionar el artículo deseado.

Presione IDIOMAS DEL DISCO

Todos los idiomas ofrecidos en el disco pueden ser ajustados. Si el idioma ajustado no es ofrecido en el disco, se seleccionará el idioma original del disco.

SALIDA DE AUDIO

Puede usted ajustar la salida audio procedente del terminal de salida audio digital.

DETENER RASTREO

Para seleccionar “CAMPO”, “CUADRO” o “AUTO” para prevenir inestabilidad o para permitir ver textos pequeños o patrones finos claramente en el modo de imagen fija.

TV PREFERENCIA

Para seleccionar cuando el material del vídeo es para pantalla ancha y se quiere reproducir en el estilo Pan&Scan, en el estilo Letterbox o en el estilo 16:9 en la pantalla.

Presione para seleccionar el artículo deseado.

Presione

Volver a visualizar el menú de DVD para

continuar el ajuste. Presione ajuste o, para salir, presione

SET

ACTION

y pase al paso 3 para ajustar otro

ACTION

dos veces.

Selección de IDIOMAS DEL DISCO [DVD solamente]

Seleccione “AUDIO”

(Fijación de fábrica : inglés)

Inglés / Español / Francés / Japonés : Original : Se seleccionará el idioma

original de cada disco.

OTRO 0000 : Se puede seleccionar el

otro idioma.

Seleccione “SUBTITULO” AUTO : Se seleccionará el mismo que fue

seleccionado en la preparación de “AUDIO”. (Fijación de fábrica)

• Si el idioma seleccionado en la preparación de “AUDIO” se utiliza durante la reproducción, los subtítulos no aparecerán.

• Si se utiliza otro idioma durante la reproducción, los subtítulos aparecerán en el idioma seleccionado en la preparación de “AUDIO”

Inglés / Español / Francés / Japonés : OTRO 0000 : Se puede seleccionar el

otro idioma.

Seleccione “MENU”

(Fijación de fábrica : inglés)

Inglés / Español / Francés / Japonés : OTRO 0000 : Se puede seleccionar el

otro idioma.

Cambio del idioma de subtítulos [Vídeo DVD solamente]

EI idioma de los subtítulos seleccionado al hacer las fijaciones iniciales se puede cambiar por otro idioma diferente, si éste se encuentra disponible.

ELEGI R : SUB TITLE

Presione

la reproducción. Cuando no haya subtítulos grabados, se visualizará “-” en lugar del número de idioma.

Presione

las teclas numéricas para seleccionar el idioma deseado.

SUBTITLE

SUB TITLE

durante

, o

Visión desde otro ángulo [DVD solamente]

Algunos discos DVD tienen escenas que han sido filmadas simultáneamente desde ángulos diferentes. Con estos discos, la misma escena podrá verse desde cada uno de estos ángulos diferentes utilizando el botón ANGLE.

ANGULO

: 1

ELEGIR : ANGLE

ANGULO

: 2

ELEGIR : ANGLE

Presione

durante la reproducción para visualizar la selección del ángulo.

Presione

repetidamente o para seleccionar el ángulo deseado.

ANGLE

rápida consulta

Guía para

Spanish Quick Use Guide/ Guía para rápida consulta

Selección de vocal para los discos de Karaoke [DVD solamente]

Presione

para visualizar la pantalla AUDIO.

ELEGI R : AUD IO /

• DVD Karaoke (1 vocal) VOZ ACTIVO VOZ INACTIVO

• DVD Karaoke (2 vocals) VOZ V1 VOZ V2 VOZ V1+V2 VOZ INACTIVO

AUDIO

durante la reproducción

Presione para seleccionar VOZ y presione seleccionar tal como se indica a continuación.

AUDIO

o para

Utilización de un menú de títulos [DVD solamente]

Algunos discos con películas, vienen con dos o más títulos. Por ejemplo, si el disco tiene un menú de títulos grabados, el botón TITLE podrá utilizarse para seleccionar el título de la película.

Presione

Ahora se visualiza una lista de los títulos del disco.

TI TLE MENU

Dogs

Love

TITLE

Castles

Birds

Dogs

of the world

durante la reproducción.

Presione o las teclas de números para

seleccionar el título deseado.

Presione

para elegir.

SET

PLAY

Cambio del idioma de la pista de sonido [DVD solamente]

EI idioma de la pista de sonido seleccionado al hacer las fijaciones iniciales se puede cambiar por otro idioma diferente, si éste se encuentra disponible.

Presione

reproducción para visualizar SONIDO en la pantalla.

ELEGI R : AUDIO

Presione

teclas numéricas para seleccionar el idioma deseado.

ELEGI R : AUDIO

AUDIO

durante la

, o las

Utilización de un menú de DVD [DVD solamente]

Algunos discos DVD ofrecen un menú especial. Este menú incluye guías para contenidos únicos, audio, subtitulos, idiomas, etc. Aunque los contenidos y las operaciones se cambian, los siguientes son unos pasos básicos para el uso del menú.

Presione

El menú de DVD introducido en el disco se visualiza ahora.

DVD MENU

1 . SUBTI TLE 2 . AUDI O

3 . ANGLE

durante la reproducción.

Presione o las teclas de números para

seleccionar el ítem deseado.

Presione

para elegir.

SET

PLAY

Ampliación de la imagen [DVD solamente]

Durante la reproducción de un DVD, puede ampliar partes específicas de una imagen y seleccionar la relación de zoom usando el botón ZOOM.

Presione

tamaño de la imagen como se indica a continuación:

■ Use los botones , , y para desplazar

ZOOM

repetidamente para cambiar el

la posición hacia arriba, hacia abajo, hacia la izquierda o hacia la derecha.

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Para solicitar ayuda, por favor llame al: 1-800-211-PANA(7262) o consúltenos a través de página web en:http: //www.panasonic.com/contactinfo

2da

3da

Funcionamiento de la ejecución de MP3/WMA/JPEG

Puede utilizar esta unidad para reproducir audio de formato MP3/WMA/JPEG, grabado para uso personal con una computadora, etc., en un CD-ROM o CD-RW. La ejecución no podrá realizarse en algunos casos, debido a las condiciones de la grabación.

Presione

o DECK.

Presione

coloque un disco MP3/WMA/JPEG en la bandeja de discos.

Presione

Se visualizará el MENU MP3/WMA/JPEG y la

ejecución se iniciará automáticamente. (Se visualizará el directorio del CD.)

Estado de la función

POWER

en el control remoto

OPEN/CLOSE

y a continuacion

para cerrarla.

REPROD

ROOT

Area de las carpetas

(La carpeta visualizada actualmente se volverá verde)

:Archivo MP3 :Archivo WMA :Archivo JPEG

:Carpeta :Carpeta principal

TECHNO DD

POPS J

AZZ

MODE DE REPRODUCCION : NORMAL

MODO DE REPRODUCCIÓN

. .

END_W

ALTZ

CUB I C NOCTURNE NORN

Carpeta principal

Area de archivos

(El archivo/ la carpeta se visualiza con un cursor.)

■ Ejecución MP3/WMA/JPEG (Durante el

modo STOP) Presione para seleccionar un archivo MP3/WMA ( / ) o un archivo JPEG ( ), y

presione

• MP3/WMA

Búsqueda hacia adelante/hacia atrás

➡ Presione

Salto de pista hacia adelante/hacia atrás

➡ Presione

• JPEG

Búsqueda siguiente/anterior

➡Presione

Inicie la muestra-diapositiva

➡Presione

Ampliar una imagen ➡ Presione Girar una imagen ➡ Presione

Presione

descrita arriba.

■ Seleccione MODO DE REPRODUCCION

(Durante el modo STOP)

Presione para seleccionar el MODO

DE REPRODUCCIÓN deseado.

[MODO DE REPRODUCCIÓN] NORMAL:

Todos los archivos se reproducen sólo una vez.

REPETICION DE UNA MUSIC:

El archivo seleccionado se reproduce repetidamente.

REPETICION DE UN ARCHIVO:

Los archivos que se encuentran en la carpeta seleccionada se reproducen repetidamente.

REPETICION DEL DISCO:

Todos los archivos se reproducen repetidamente.

SET

PLAY

FF/SLOW+

durante la ejecución.

SKIP+

durante la ejecución.

SKIP+

FF/SLOW+

STOP

para detener la operación

REW/SLOW-

| o

SKIP-

| o

SKIP-

REW/SLOW-

| .

ZOOM

ANGLE

rápida consulta

Guía para

Presione

DVD MENU PRINCIPAL.

ACTION

para regresar al

Index

DECK & VCR

A ACTION button ................................. 8, 18

Accessories............................................ 4

ADD/DELETE button

(Add or Delete a Channel) ............ 8, 19

Audio Broadcast types

(Stereo/SAP/Mono) ............................ 26

Audio Mode (Playback, Recording) .... 27

Auto Operation Functions .................... 31

Auto Shut-Off ........................................ 33

B Batteries ................................................. 4

Blue Light (ON/OFF Feature)........... 9, 32

C Channel (“SET UP CHANNEL”).......... 18

Channel Up/Down,

Tracking/V-Lock Button .................... 4, 8

Clock (“SET CLOCK”) .......................... 18

CM/ZERO SEARCH button ............. 8, 30

Commercial Skip ................................. 30

Connections................................. 12 ~ 15

Copy Your Tapes (Dubbing) ............... 35

COUNTER RESET button ............... 8, 30

Customer Services Directory............... 61

D DISPLAY button ............................... 8, 11

DST (Daylight Saving Time) ................ 19

E EJECT button ................................... 8, 20

ENTER button

(For tuning TV Channel) ................ 8, 28

F FAST FORWARD/SLOW+ button ..... 8, 20

H Head Cleaning ...................................... 4

I Index Search ........................................ 30

Indicator (Multi Function Display) ....... 11

Initial Setup (Ready to Play) ......... 16, 17

INPUT button ................................... 8, 35

L Limited Warranty ........................... 60, 61

Location of Controls

(Remote, DECK) .......................... 8 ~ 10

MMulti-Brand Control ....................... 28, 29

Multi Function Display (Front Display)

ON/OFF Feature ................................... 34

O On-Screen Displays (VCR) ................. 11

One Touch Recording ......................... 21

P PLAY button (Playback a Tape) ...... 8, 20

POWER button ....................................... 8

PROG button (PROGRAM).............. 8, 24

Program Clear, Review, Replace ....... 25

Q Quality Picture ....................................... 4

R REC button (Record on a Tape) ..... 8, 21

Record Tab ............................................ 6

Remote Sensor ...................................... 9

Remote Warning .................................. 34

Repeat Play ......................................... 31

Reset All Memory Functions ................. 9

REWIND/SLOW- button ................... 8, 20

S SAP/Hi-Fi ............................................. 27

SEARCH button ............................... 8, 30

Spanish Quick Use Guide ........... 62 ~ 69

Specifications......................................... 7

SPEED button .................................. 8, 21

Still (Freeze) Picture ............................ 20

STILL/PAUSE button (Still Picture) .. 8, 20

STOP button ..................................... 8, 20

T Tape Position, Tape Status ................. 31

Tape Select .......................................... 31

Timer Recording .................................. 24

Trouble Shooting ........................... 58, 59

TV mode button................................ 8, 28

V VCR Lock ............................................. 32

VCR mode button ............................ 8, 28

VCR/TV button ................................. 8, 21

VCR/TV Selection Feature .................. 32

VOLUME +/- button (TV Volume) .... 8, 28

WWarning and Instruction Displays ....... 57

Weak Signal Display ........................... 33

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

DVD

A ACTION button ................................. 8, 52

ANGLE button

(Multiple Angle Viewing) ......... 8, 37, 51

AUDIO button

(Audio Soundtrack Language) ...... 8, 36

Audio Output

(For Selecting Audio Output) ............. 53

Auto-Power Off Function ..................... 23

A/V OPTIMIZER.................................... 55

B Bonus Group (For DVD-Audio) ........... 41

C CLEAR button .................................. 8, 39

Component Video Output .............. 10, 13

D Direct Navigator ................................... 42

Disc Languages ................................... 52

DISPLAY button

(“On-Screen Display”).................... 8, 44

DTS ...................................................... 14

DVD-Audio ........................................... 41

DVD Menu ........................................... 38

DVD mode button ............................ 8, 28

DVD-RAM (DVD-VR) ........................... 42

F Frame by Frame Picture ...................... 23

Forward/Reverse Chapter/Track Skip... 23

Forward/Reverse Scene Search .......... 23

J JPEG ............................................ 49 ~ 51

K Karaoke

(Vocal Selection for Karaoke Discs) ... 37

L Language Code List ............................ 56

MMENU button

(To display DVD Menu) ................. 8, 38

MP3 ...................................................... 49

Multiple Angle Viewing........................ 37

O OPEN/CLOSE button....................... 8, 22

Optical Digital Audio Output .......... 10, 15

P PAGE button (Still Image Skip) ....... 8, 41

PLAY button (Play a Disc) ............... 8, 22

Play List................................................ 43

Program Play (For CD) ........................ 39

Progressive Scan ..................... 10, 13, 55

R Random Play (For CD)........................ 40

Repeat Play ................................... 47, 48

Resume Function ................................. 23

RETURN button ............................... 8, 22

Rotation................................................ 51

S SKIP+

(Forward/Reverse Chapter/Track) 8, 23

Slide-show ........................................... 50

SLOW+/SLOW- button

(Slow Motion Picture) .................... 8, 23

STILL/PAUSE button

(Still Picture or Pause) ................... 8, 23

Still Mode (For selecting “FIELD” or “FRAME”) .. 54

STOP button ..................................... 8, 22

SUB TITLE button (For selecting Subtitle Language) ... 8, 36

S-Video Out .................................... 10, 13

T TITLE button (Title Menu) ................ 8, 38

TV Mode (For selecting the screen display style) .. 54

V VOLUME ADJUST button ................ 8, 40

V.S.S. (Virtual Surround Sound) ..... 8, 23

WWMA ..................................................... 49

Z ZOOM button (Picture Zoom) ..... 8, 37, 51

l or SKIP- l button

Information

For Your

LSQT0797 A

Panasonic Consumer Electronics Company, Division of Matsushita Electric Corporation of America

One Panasonic Way Secaucus, New Jersey 07094

Panasonic Sales Company (“PSC”), Division of Matsushita Electric of Puerto Rico, Inc.

Ave. 65 de Infantería. Km. 9.5 San Gabriel Industrial Park, Carolina, Puerto Rico 00985

Printed in Indonesia

LSQT0797 A

S0104-1024

Technics PV-D4754S User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Table of Contents

Connections

Manual Clock Set

Resume Function

Timer Recording

Index Search

Zero Search

Commercial Skip

Repeat Play

Tape Position Display

Remote Warning Feature

Disc Operation

TI TLE MENU

DVD MENU

Direct Navigator

Play List

AUDIO OUTPUT

ST IL L MODE :

A/V OPTIMIZER

Language Code List

Index