Technibel KPAFP125R5I, KPAFP185R5I, KPAFP165R5I Technical Data & Service Manual

Download

Page 1

TECHNICAL DATA & SERVICE MANUAL

SPLIT SYSTEM AIR CONDITIONER

KPAFP165R5I 38.7105.958

0.8180.451.1 09/2006

KPAFP185R5I

Model No. Product Code No.

KPAFP125R5I 38.7105.956

38.7105.957

Page 2

IMPORTANT! Please read before installation

This air conditioning system meets strict safety and operating standards. For the installer or service person, it is important to install or service the system so that it operates safely and efficiently.

For safe installation and trouble-free operation, you must:

• Carefully read this instruction booklet before beginning.

• Follow each installation or repair step exactly as shown.

• Observe all local, state and national electrical codes.

• Pay close attention to all warning and caution notices given in this manual.

•The unit must be supplied with a dedicated electrical line.

This symbol refers to a hazard or unsafe practice which can result in severe personal injury or death.

This symbol refers to a hazard or unsafe practice which can result in personal injury or product or property damage.

If necessary, get help

These instructions are all you need for most installation sites and maintenance conditions. If you require help for a special problem, contact our sale/service outlet or your certified dealer for additional instructions.

In case of improper installation

The manufacturer shall in no way be responsible for improper installation or maintenance service, including failure to follow the instructions in this document.

SPECIAL PRECAUTIONS

• During installation, connect before the refrigerant system and then the wiring one; proceed in the reverse orden when removing the units.

When wiring

ELECTRICAL SHOCK CAN CAUSE SEVERE PERSONAL INJURY OR DEATH. ONLY QUALIFIED, EXPERIENCED ELECTRICIANS SHOULD ATTEMPT TO WIRE THIS SYSTEM.

• Do not supply power to the unit until all wiring and tubing are completed or reconnected and checked, to ensure the grounding.

• Highly dangerous electrical voltages are used in this system. Carefully refer to the wiring diagram and these instructions when wiring. Improper connections and inadequate grounding can cause accidental injury and death.

• Ground the unit following local electrical codes.

• The Yellow/Green wire cannot be used for any connection different from the ground connection.

• Connect all wiring tightly. Loose wiring may cause overheating at connection points and a possible fire hazard.

• Do not allow wiring to touch the refrigerant tubing, compressor, or any moving parts of the fan.

• Do not use multi-core cable when wiring the power supply and control lines. Use separate cables for each type of line.

When transporting

Be careful when picking up and moving the indoor and outdoor units. Get a partner to help, and bend your knees when lifting to reduce strain on your back. Sharp edges or thin aluminium fins on the air conditioner can cut your fingers.

When installing...

• Keep all tubing runs as short as possible.

• Use the flare method for connecting tubing.

• Apply refrigerant lubricant to the matching surfaces of the flare and union tubes before connecting them; screw by hand and then tighten the nut with a torque wrench for a leak-free connection.

• Check carefully for leaks before starting the test run.

NOTE:

Depending on the system type, liquid and gas lines may be either narrow or wide. Therefore, to avoid confusion, the refrigerant tubing for your particular model is specified as narrow tube for liquid, wide tube for gas.

When servicing

• Turn the power OFF at the main power board before opening the unit to check or repair electrical parts and wiring.

• Keep your fingers and clothing away from any moving parts.

• Clean up the site after the work, remembering to check that no metal scraps or bits of wiring have been left inside the unit being serviced.

• Ventilate the room during the installation or test

ing the refrigeration system; make sure that, after the installation, no gas leaks are present, because this could produce toxic gas and dangerous if in contact with flames or heat-sources.

WARNING

CAUTION

WARNING

… In a ceiling

Make sure the ceiling is strong enough to hold the unit-weight. It may be necessary to build a strong wooden or metal frame to provide added support.

… In a room

Properly insulate any tubing run inside a room to prevent "sweating", which can cause dripping and water damage to walls and floors.

... In moist or uneven locations

Use a raised concrete base to provide a solid level foundation for the outdoor unit. This prevents damage and abnormal vibrations.

... In area with strong winds

Securely anchor the outdoor unit down with bolts and a metal frame. Provide a suitable air baffle.

... In a snowy area (for heat pump-type systems)

Install the outdoor unit on a raised platform that is higher then drifting snow. Provide snow vents.

When connecting refrigerant tubing

Page 3

Page

1. SPECIFICATIONS

1-1 Unit specifications 4 1-2 Major Component specifications 6 1-3 Other Component specifications 8

2. DIMENSIONAL DATA

3. ELECTRICAL DATA

3-1 Electric Wiring Diagram 10 3-2 Control PCB switches and functions 11

4. PROCESS AND FUNCTIONS

4-1 Control function 12

5. REPLACING PCB

5-1 Replacing PCB 15 5-2 How to replace PCB 16 5-3 How to replace EEPROM with EEPROM included in PCB service pack 17 5-4 Table of setting 19

6. SERVICE PROCEDURE

6-1 Meaning of alarm message 20 6-2 Led indicator messages on outdoor control PCB 21 6-3 Symptoms and parts to inspect 22 6-4 Details of alarm messages 23 6-5 Table of thermistor characteristics 26

7. OUTDOOR UNIT MAINTENANCE REMOTE CONTROL

7-1 Overwiew

7-2 Functions

7-3 Normal display operations and functions

7-4 Monitoring operations:

Display of indoor unit and outdoor unit sensor temperatures

7-5 Monitoring the outdoor unit alarm history:

Display of outdoor unit alarm history 32

7-6 Setting modes: setting of outdoor unit EEPROM

Table of Contents

Page 4

1. SPECIFICATIONS

1-1 Unit Specifications

KPAFP125R5I

Power source

oltage ratin

Performance

Capacity Air circulation (High/Med./Low) m³/h

Features

Controls/Temperature controls Remote Controller (Option) wired

wireless Fan speed Airflow direction Air Filter Sound pressure level high/med/low dB(A) Refrigerant tubing connections Refrigerant Narrow tube mm(in.) tube diameter Wide tube mm(in.) Refrigerant Refrigerant control

Dimensions & Wei

Dimensions Unit Height mm

Width mm Depth mm

Package dimensions Unit Height mm

Width mm Depth mm Volume m3

Weight Net kg

Shipping kg

DATA SUBJECT TO CHANGE WITHOUT NOTICE

680

Auto (Remote control)

Electronic expansion valve

Washable

55/51/46

Flare type

6,35 (1/4) 12,7 (1/2)

R410A

220 - 240V ~ 50Hz

230V

Cooling Heating

See catalogue with the requested matching

700/590/500

Microprocessor/ I.C. thermostat

3 and Auto

K70D036Z / K70D042Z K70D038Z / K70D040Z

296

23,5 31,5

900

0,24

813

1011

190

Page 5

KPAFP165/185R5I

Power source

oltage ratin

Performance

Capacity Air circulation (High/Med./Low) m³/h

Features

Controls/Temperature controls Remote Controller (Option) wired

Dimensions & Wei

Dimensions Unit Height mm

Width mm Depth mm

Package dimensions Unit Height mm

Width mm Depth mm Volume m3

Weight Net kg

Shipping kg

DATA SUBJECT TO CHANGE WITHOUT NOTICE

Electronic expansion valve

Flare type

31,5

813 296

1011

0,24 23,5

190

220 - 240V ~ 50Hz

230V

Cooling Heating

See catalogue with the requested matching

Microprocessor/ I.C. thermostat

830/760/665

K70D038Z / K70D040Z

900

680

K70D036Z / K70D042Z

Washable

6,35 (1/4)

R410A

12,7 (1/2)

3 and Auto

Auto (Remote control)

60/57/54

Page 6

1-2 Major Component Specifications

KPAFP125R5I

Controller PCB

Part No. Controls

Fan & Fan Motor

Type Q'ty ……. Dia. and lenght mm Fan motor model…Q'ty No. Of poles…rpm (230 V, High) Running Amps A Power input W Coil resistance (Ambient temp. 25 °C )

Ω

GRY-WHT: 194 ÷ 223

WHT-PNK: 238 ÷ 274

WHT-VLT: 80,1 ÷ 92,2 VLT-ORG: 80,1 ÷ 92,2 ORG-YEL: 200 ÷ 230

Safety devices Type

Operating temp. Open °C

Close °C

Run capacitor µF

VAC

Flap motor

Model Rating Rpm Nominal output W Coil resistance (25°C)

kΩ

Heat Exch. Coil

Coil Rows Fin pitch mm face area m2

DATA SUBJECT TO CHANGE WITHOUT NOTICE

450

1,5

Internal thermal protector

145 ± 5K

Automatic reclosing

Microprocessor

CR-CRP50A-B

2…. Ø 130 L 180

0,29

Centrifugal fan

K48407-MO1596 …1

4… 1160

M2LB24ZA12

15,62 ± 15%

2,5

0,167

Aluminium plate fin / Copper tube

1,8

240 VAC

Page 7

KPAFP165/185R5I

Controller PCB

Part No. Controls

Fan & Fan Motor

Type Q'ty ……. Dia. and lenght mm Fan motor model…Q'ty No. Of poles…rpm (230 V, High) Running Amps A Power input W Coil resistance (Ambient temp. 25 °C )

Ω

GRY-WHT: 124 ÷ 144

WHT-PNK: 255 ÷ 294

WHT-VLT: 69,3 ÷ 79,8 VLT-ORG: 69,3 ÷ 79,8 ORG-YEL: 200 ÷ 233

Safety devices Type

Operating temp. Open °C

Close °C

Run capacitor µF

VAC

Flap motor

Model Rating Rpm Nominal output W Coil resistance (25°C)

kΩ

Heat Exch. Coil

Coil Rows Fin pitch mm face area m2

DATA SUBJECT TO CHANGE WITHOUT NOTICE

0,167

1,6

Aluminium plate fin / Copper tube

Automatic reclosing

2,5

M2LB24ZA12

240 VAC

440

CR-CRP50A-B

Centrifugal fan

15,62 ± 15%

Microprocessor

2…. Ø 130 L 180

K48410-MO1598 …1

4… 1160

0,41

Internal thermal protector

145 ± 5K

Page 8

1-3 Other Component Specifications

Trasformer

Rating Primary

Secondary 1 Secondary 2 Secondary 3

Thermal cut-off temp.

Thermistor

(

Coil sensor E1, E2

)

Resistance

kΩ

Thermistor

(

Room sensor TA

)

Resistance

kΩ

ATR-IIJ225A

VAC 230V, 50Hz

AC 20V - 0.2A AC 14V - 0.3A

PBC-41E-S26

AC 10,2V - 1.4A

136°C

0 °C 15,0 ± 5%

25 °C 5,0 ± 4%

DHKTEC-35-S85N

Page 9

2. DIMENSIONAL DATA

Units: mm

Page 10

3. ELECTRICAL DATA

3-1 Electric Wiring Diagram

7P terminal board

1(L) 2(N) U1 U2 R1 R2

iri

remote

con

troller

power

supp

inter-unit

con

trol

Page 11

3-2 Control PCB switches and functions

CR-TRP50A-B OC (CN040)

EMG (CN044)

VARISTOR (VA041)

JP1 DISP (CN072)

EXCT (CN073) FILTER (JP001)

(CN070) CHK (CN071)

FAN DRIVE GRL

(CN032) (CN020) T10 (CN061)

POWER LED

(D002) EEPROM

(IC010)

T10: 6 plug (yellow): used for remote control. (Refer to the remote control section) (CN061) 1- start/stop input 2- COM

3- remote control prohibit/release input 4- start signal output 5- COM (+DC12v) 6- alarm signal output T10

EXCT: 2P plug (red): Can be used for demand control. When imput is present, forces the unit to operate

(CN073) with the termostat OFF.

DISP: 2P plug (white): Short-circuiting this plug allows the unit to be operated by the remote controller, even if it is not (CN072) connected to an outdoor unit. (In this case, alarm "E04", which indicates trouble in the serial communication

between the indoor and outdoor unit, does not occur.)

CHK: 2P plug (white): Test pin. Short-circuiting this pin allows the indoor FM (H fan speed), drain pump, (CN071) flap motor (F1 position), and electronic expansion valve full-open position to checked. However this function

turns OFF if the indoor unit protection mechanism is activated. The unit can be operated even if the remote controller and outdoor unit are not connected. However even if the remote controller cannot is connected, it cannot be used to operate the unit. This function can be used for short-term tests.

JP1: Jumper wire: Allows selection of the T10 terminal (JP001)

Page 12

4. PROCESS AND FUNCTIONS

4-1 control functions

Page 13

Page 14

Page 15

5. REPLACING PCB

5-1 Replacing PCB

About EEPROM

(Erasable Programmable Read-Only Memory) EEPROM is a component in which the various information necessary for functionning can be electronically written or erased. This component holds informations that is essential for the running of the unit, and must be handled with care.

D002

led lamp (red)

Page 16