How it Works
TechNexion
Loading...
TOUCAN TC-0710 SLIM HMI
Product Manual
26 pgs1.51 Mb0

TechNexion TOUCAN TC-0710 SLIM HMI Product Manual

Download
TOUCAN TC-0710 SLIM HMI PRODUCT MANUAL
(TC-0710)
VER. 1.00
July 27, 2018
Page 2 of 26
REVISION HISTORY
Revision
Date
Originator
Notes
1.00
July 27, 2018
TechNexion
First public release
Page 3 of 26
TABLE OF CONTENTS
1. Introduction ............................................................................................................................................... 4
1.1. General Care and Maintenance ......................................................................................................... 4
2. TC-0710 Product Overview ....................................................................................................................... 5
2.1. Functional Block Diagram .................................................................................................................. 5
2.2. Dimensions ......................................................................................................................................... 6
2.3. Device Cut-out Dimensions For Mounting Though a Panel ............................................................... 7
2.4. External Connectors ........................................................................................................................... 8
2.5. Internal Board Connectors ............................................................................................................... 10
3. External Connectors ................................................................................................................................ 12
3.1. Gigabit Ethernet Interface................................................................................................................. 12
3.2. Power Input Connector ..................................................................................................................... 12
3.3. Digital I/O Connector (GPIO) ............................................................................................................ 13
3.4. USB Host Connector ........................................................................................................................ 13
3.5. HDMI (High Definition Multi-Media Interface) ................................................................................... 13
3.6. CAN Bus Connector (CANBus) ........................................................................................................ 14
3.7. Serial Port / MDB Connector (RS-XXX) ........................................................................................... 15
3.8. USB OTG Connector ........................................................................................................................ 16
3.9. MicroSD Connector .......................................................................................................................... 17
3.10. S1 Button ........................................................................................................................................ 17
3.11. RST Button ..................................................................................................................................... 17
3.12. Antenna Holes ................................................................................................................................ 17
4. Internal Connectors and Expansion Options .......................................................................................... 18
4.1. RTC Battery Connector .................................................................................................................... 18
4.2. Audio Connectors ............................................................................................................................. 19
4.3. Power Fuse ...................................................................................................................................... 19
4.4. S1 Button Boot Select Mode DIP Switch.......................................................................................... 19
5. Mounting.................................................................................................................................................. 20
5.1. VESA Mounting ................................................................................................................................ 20
5.2. Rear Mounting and Mounting Clips Installation ................................................................................ 21
5.3. Surface Mounting and O-ring Installation ......................................................................................... 22
6. Ordering Information ............................................................................................................................... 23
6.1. Custom Part Number Rule ............................................................................................................... 23
6.2. Standard Package Contents ............................................................................................................ 24
7. Important Notice ...................................................................................................................................... 25
8. DISCLAIMER .......................................................................................................................................... 26
Page 4 of 26
1. Introduction
1.1. General Care and Maintenance
Your device is a product of superior design and craftsmanship and should be treated with care. The following suggestions will help you.
• Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that will corrode electronic circuits. If your device does get wet, allow it to dry completely.
• Do not use or store the device in dusty or dirty areas. Its parts and electronic components can be damaged.
• Do not store the device in hot areas. High temperatures can shorten the life of electronic devices, damage batteries, and warp or melt certain plastics.
• Do not store the device in cold areas. When the device returns to its normal temperature, moisture can form inside the device and damage electronic circuit boards.
• Do not open the device while power is on. Otherwise electrical shock may result.
• Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and
fine mechanics.
• Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.
• Do not paint the device. Paint can clog the moving parts and prevent proper operation.
• Unauthorized modifications or attachments could damage the device and may violate regulations
governing radio devices.
These suggestions apply equally to your device, battery, charger, or any enhancement. If any device is not working properly, take it to the nearest authorized service facility for service. Regulatory information
Disposal of Waste Equipment by Users in Private Household in the European Union This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the
environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product.
We hereby declare that the product is in compliance with the essential requirements and other relevant provisions of European Directive 1999/5/EC (radio equipment and telecommunications terminal equipment Directive).
Page 5 of 26
2. TC-0710 Product Overview
2.1. Functional Block Diagram
Page 6 of 26
2.2. Dimensions
The following figure shows the TC-0710 dimensions (unit: mm):
Page 7 of 26
2.3. Device Cut-out Dimensions For Mounting Though a Panel
The TC-0710 can be mounted on the front or the back of the panel. In order to mount it from the front, a nominal rectangular cutout must be made in the panel. The following drawing shows the dimensions of the cut-out area (unit: mm):
Page 8 of 26
2.4. External Connectors
The TC-0710 has a number of external connectors. Rear view:
11 10
9 8
1 2 3 4 5 6 7
External Connectors:
No.
Description
No.
Description
1
LAN RJ45 and PoE connector
7
Serial Port (RS-XXX) connector
2
Power Input (10~30VDC) connector
8
MicroSD cardslot
3
GPIO connector
9
USB OTG connector
4
USB Host connector
10
S1 Boot Select button
5
HDMI connector
11
Reset button
6
CAN Bus (CANBus) connector
Page 9 of 26
Bottom view:
1 2 3 4 5 6 7
Right side view:
8 8 9 10 11
External Connectors:
No.
Description
No.
Description
1
LAN RJ45 and PoE connector
7
Serial Port (RS-XXX) connector
2
Power Input (10~30VDC) connector
8
MicroSD cardslot
3
GPIO connector
9
USB OTG connector
4
USB Host connector
10
S1 Boot Select button
5
HDMI connector
11
Reset button
6
CAN Bus (CANBus) connector
Page 10 of 26
2.5. Internal Board Connectors
The TC-0710 has several connectors, switches and internal expansion options. It is necessary to remove the EDM computing module to access several switches, headers and connectors. Rear view (opened device) with the EDM computing module:
A EDM Computing Module B C
E G D F
Internal Connectors and Switches:
No.
Description
No.
Description
A
RTC Battery connector
E
USB (2 port) header
B
Mic in connector
F
USB (shared with touchpanel)
C
Line out connector
G
Power Fuse
D
SW1 DIP switch for RS-XXX Serial Port
Page 11 of 26
Rear view (opened device) without the EDM computing module:
A H* B C
E I* D G F
Internal Connectors and Switches:
No.
Description
No.
Description
A
RTC Battery connector
F
USB (shared with touchpanel)
B
Mic in connector
G
Power Fuse
C
Line out connector
H*
Boot Select switch for S1 button
D
SW1 DIP switch for RS-XXX Serial Port
I*
SW2 MDB
E
USB (2 port) header
NOTE: Items marked with * are accessible only after removing the EDM computing module.
Page 12 of 26
3. External Connectors
3.1. Gigabit Ethernet Interface
The TC-0710 by default comes with a single Gigabit Ethernet RJ45 connector. This connector can support 802.3at Power over Ethernet functionality by connecting it to an 802.3at compliant PoE switch or power injector.
Pin #
1000 Mbps
100 Mbps
10 Mbps
1
MDI0+
Transmit Data+
Transmit Data+
2
MDI0-
Transmit Data-
Transmit Data-
3
MDI1+
Receive Data+
Receive Data+
4
MDI2+
5
MDI2-
6
MDI1-
Receive Data-
Receive Data-
7
MDI3+
8
MDI3-
3.2. Power Input Connector
The TC-0710 can be powered either over the DC INPUT connector or PoE over the RJ45 LAN port. NOTE: Do not power the unit by DC input when you apply power over the Power over Ethernet (RJ45)!
Pin #
Signal
Description
1
GND
Ground
2
VCC
DC Voltage input (10~30VDC)
Header on TC-0710: Molex 43045-0200 (2-pin Micro-Fit 3.0). Cable receptacle: Molex 43025-0200 (2-pin Micro-Fit 3.0) plug with crimp contact Molex 43030-0007.
Page 13 of 26
3.3. Digital I/O Connector (GPIO)
The TC-0710 has one galvanic isolated GPIO Expansion header with the following pinout:
GPIO:
Pin # Signal
Description Voltage
Current Max.
GPIO Kernel
GPIO Bank/IO
Min.
Typ.
Max.
1
GPIO1A
DIG_IN1
1.2V
1.4V
1A
90
6_31
2
GPIO1B
DIG_IN2
1.2V
1.4V
1A
191
3_26
3
GND_DIO
Ground for digital I/O
4
GND
Common Ground
5
GPIO1C
DIG_OUT5
5V 34V
1A
163
6_03
6
GPIO1D
DIG_OUT6
5V 34V
1A
24
1_24
7
VCC_DIO
Supply input for digital I/O
5V 34V
8
VCC*
Supply output
10V
30V
NOTE: * VCC supply output is based on the VDC input. There is no supply output when device is powered over the Power over Ethernet (RJ45)!
Header on TC-0710: Molex 43045-0800 (8-pin Micro-Fit 3.0). Cable receptacle: Molex 43025-0800 (8-pin Micro-Fit 3.0) plug with crimp contact Molex 43030-0007.
3.4. USB Host Connector
The TC-0710 has a standard single USB Host connector (USB 2.0 signals only) to connect to a USB peripheral such as a keyboard, mouse, USB storage device or USB hub.
3.5. HDMI (High Definition Multi-Media Interface)
The HDMI interface available on the TC-0710 is based on the “HDMI transmitter” & “HDMI 3D TX PHY” integrated into the NXP i.MX6 processor and can be configured to support a secondary display.
The HDMI supports the following standards & features:
• High-Definition Multimedia Interface Specification, Version 1.4a
• Digital Visual Interface, Revision 1.0
• HDMI Compliance Test Specification, Version 1.4a
• Support for up to 720p at 100Hz and 720i at 200Hz or 1080p at 60Hz and 1080i/720i at 120Hz
HDTV display resolutions and up to QXGA graphic display resolutions.
• Support for 4k x 2k and 3D video formats
• Support for up to 16-bit Deep Color modes
For additional details, please refer to the “EDM1-CF-IMX6 Hardware Manual”.
Page 14 of 26
3.6. CAN Bus Connector (CANBus)
The TC-0710 has two galvanic isolated CAN Bus interfaces with the following pinout:
CANBus:
Pin #
Signal
Description
Interface
1
GND_CAN
Ground for CAN
2 CAN1A_TERM_P
To enable CAN1A Termination, bridge with CAN1A_P
can0
3
CAN1A_P
CAN Bus 1A high (-24~+24V)
can0
4
CAN1A_N
CAN Bus 1A low (-24~+24V)
can0
5
CAN1A_TERM_N
To enable CAN1A Termination, bridge with CAN1A_N
can0
6
NC 7 GND_CAN
Ground for CAN
8 CAN1B_TERM_P
To enable CAN1B Termination, bridge with CAN1B_P
can1
9
CAN1B_P
CAN Bus 1B high (-24~+24V)
can1
10
CAN1B_N
CAN Bus 1B low (-24~+24V)
can1
11
CAN1B_TERM_N
To enable CAN1B Termination, bridge with CAN1B_N
can1
12
NC
Header on TC-0710: Molex 43045-1200 (12-pin Micro-Fit 3.0). Cable receptacle: Molex 43025-1200 (12-pin Micro-Fit 3.0) plug with crimp contact Molex 43030-0007.
Page 15 of 26
3.7. Serial Port / MDB Connector (RS-XXX)
The TC-0710 has dual 4-wire galvanic isolated serial port that can be configured as follows: The primary serial port can only be used as a standard RS-232. The secondary port can be configured either as RS­232, RS-422, RS-485 or utilize MDB protocol. This serial port is set by default as RS-232. Setting the TC­0710 in other mode will require to open the device and adjust the internal SW1 DIP and SW2 switch
settings on the Toucan circuit board. The SW1 DIP switch can be found at location “E” and SW2 at
location “F” in chapter 2.5. Internal Board Connectors of this manual.
SW1:
Pin #
RS-232 (default)
RS-422
RS-485
MDB
1-8
ON
OFF
OFF
OFF
2-7
OFF
ON
OFF
OFF
3-6
OFF
OFF
ON
OFF
4-5
OFF
ON
ON
OFF
SW2:
Pin #
RS-232 (default)
RS-422
RS-485
MDB
1-2
OFF
OFF
OFF
ON
RS-232 + RS-232 (default setup):
Pin #
Signal
Description
Device
1
GND
Ground
2 SERIAL1A_TXD
Port#1A Transmit data (output)
ttymxc0
3
SERIAL1A_RXD
Port#1A Receive data (input)
ttymxc0
4
SERIAL1A_RTS
Port#1A Request-to-send (output)
ttymxc0
5
SERIAL1A_CTS
Port#1A Clear-to-send (input)
ttymxc0
6
GND
Ground
7 SERIAL1B_TXD
Port#1B Transmit data (output)
ttymxc1
8
SERIAL1B_RXD
Port#1B Receive data (input)
ttymxc1
9
SERIAL1B_RTS
Port#1B Request-to-send (output)
ttymxc1
10
SERIAL1B_CTS
Port#1B Clear-to-send (input)
ttymxc1
RS-232 + RS-422:
Pin #
Signal
Description
Device
1~5
SERIAL1A
Identical as above
ttymxc0
6
GND
Ground
7 SERIAL1B+
RS-485 positive data signal
ttymxc1
8
NC 9 NC
10
SERIAL1B-
RS-485 negative data signal
ttymxc1
Page 16 of 26
RS-232 + RS-485:
Pin #
Signal
Description
Device
1~5
SERIAL1A
Identical as above
ttymxc0
6
GND
Ground
7 SERIAL1B+
RS-485 positive data signal
ttymxc1
8
NC 9 NC
10
SERIAL1B-
RS-485 negative data signal
ttymxc1
RS-232 + MDB:
Pin #
Signal
Description
1~5
SERIAL1A
Identical as above
6
GND
Ground
7
MDB_TXD
MDB transmit data signal (output)
8
MDB_RXD2
MDB receive data signal (input)
9
MDB_WakeUp
MDB wakeup signal (output)
10
MDB_VCC
MDB wakeup pull up VCC (0~5V)
Header on TC-0710: Molex 43045-1000 (10-pin Micro-Fit 3.0). Cable receptacle: Molex 43025-1000 (10-pin Micro-Fit 3.0) plug with crimp contact Molex 43030-0007.
3.8. USB OTG Connector
The TC-0710 has one USB OTG connector (USB 2.0 signals only) that can be used to connect a host computer to the unit for programming and update purposes.
Pin #
Signal
Description
1
VBUS
5V Universal Serial Bus Power
2
USB_D-
Universal Serial Bus differential pair signal 3
USB_D+
4
USB_OTG_ID
Universal Serial Bus On-The-Go detection signal
5
GND
Ground
6
NC 7
NC 8
GND
Ground
9
NC 10
NC
Page 17 of 26
3.9. MicroSD Connector
The TC-0710 features a standard microSD cardslot which is connected to the NXP i.MX6 integrated “Ultra Secured Digital Host Controller” (uSDHC).
The following main features are supported by uSDHC:
• Compatible with the MMC System Specification version 4.2/4.3/4.4/4.41/5.0.
• Conforms to the SD Host Controller Standard Specification version 3.0.
• Compatible with the SD Memory Card Specification version 3.0 and supports the “Extended
Capacity SD Memory Card”.
• Compatible with the SDIO Card Specification version 3.0.
• Supports 1-bit / 4-bit SD and SDIO modes
The MMC/SD/SDIO host controller can support a single MMC / SD / SDIO card or device.
3.10. S1 Button
The TC-0710 by default boots the unit from internal flash storage (eMMC). By pressing the “S1” button before applying power to the unit and keeping the button pressed for 10 seconds, the unit will boot from an alternative boot media, such as a microSD card. The primary and alternative booth media are determined by internal DIP switch settings. Please see section 4.4. S1 Button Boot Select Mode DIP
Switch for more details.
3.11. RST Button
The TC-0710 features a “RST” button for system reset.
3.12. Antenna Holes
There are two antenna holes available (on the top side). They come fitted with breakaway metal tabs. In order to utilize them, the tabs must be removed by carefully using pincers or pliers.
Page 18 of 26
4. Internal Connectors and Expansion Options
Rear view (opened device) without the EDM computing module:
A H* B C
E I* D G F
Internal Connectors and Switches:
No.
Description
No.
Description
A
RTC Battery connector
F
USB (shared with touchpanel)
B
Mic in connector
G
Power Fuse
C
Line out connector
H*
Boot Select switch for S1 button
D
SW1 DIP switch for RS-XXX Serial Port
I*
SW2 MDB
E
USB (2 port) header
NOTE: Items marked with * are accessible only after removing the EDM computing module.
4.1. RTC Battery Connector
The TC-0710 has an internal RTC backup battery connector (Marked A).
Pin #
Signal
Description
1
GND
Ground
2
RTC_VCC
3V (connect to standard CR2032 battery)
Page 19 of 26
4.2. Audio Connectors
The TC-0710 has two internal audio connectors to connect a passive microphone or a speaker (Marked B and C respectively) The line out signal is pre-amplified with a 2W Texas Instruments TPA2025D1 amplifier.
Mic in (Marked B):
Pin #
Signal
Description
1
MIC
Microphone Signal
2
AGND
Microphone Ground Signal
Line out (Marked C):
Pin #
Signal
Description
1
SP+
Speaker Positive Signal
2
SP-
Speaker Analog Ground Signal
4.3. Power Fuse
The TC-0710 features a fast-acting square ceramic surface mount fuse Conquer SEF3A125V (Marked G) The fuse has the following current and voltage ratings: 3A at 125V.
4.4. S1 Button Boot Select Mode DIP Switch
The TC-0710 has an internal S1 Button Boot Mode Select DIP switch (Marked H).
Pin #
Boot from SD (default)
Boot from iNAND
1
ON
OFF
2
ON
OFF
3
OFF
ON 4 OFF
ON 5 OFF
ON 6 OFF
OFF
Page 20 of 26
5. Mounting
This section describes the mounting procedures for TC-0710. The material in area of the mounting must provide sufficient strength for safe mounting of this device.
5.1. VESA Mounting
The TC-0700 is compatible with the VESA MIS-C Standard 35*75mm hole pattern. There are 4 VESA MIS-C (M4) mounting holes on the rear side of the device. M4 screw holes are a depth of 6mm.
1 2
3 4
Page 21 of 26
5.2. Rear Mounting and Mounting Clips Installation
There are 6 mounting clips required for rear mounting.
1 2 6 3
5 4
Please follow the steps below to secure the clips. Prepare mounting hook, post and screw (M3) (Step 1). Locate all removable tabs on the rear side of your device and use pincers or pliers to remove the tabs (Step 2-3). Press the mounting clip into the holes at an angle and slowly straighten it (Step 4-5). Then tighten the screw to the surface (Step 6). Repeat the steps for all clips required to secure your device.
Page 22 of 26
5.3. Surface Mounting and O-ring Installation
There are 8 mounting holes (M4) on the rear side of the device required for surface mounting. M4 screws with at least 6mm head-to-tip length are required to secure this device.
1 2 3
8 4
7 6 5
Please follow the steps below to properly install the waterproof rubber O-ring. Prepare your device and O­ring (Step 1-2). First, align the O-ring with the groove and press the O-ring into the corners of the O-ring groove (Step 3-4). Then, press it into the center (Step 5). Finally, stretch it uniformly around the O-ring groove (Step 6). Do not pull from one side, and make sure that you stretch it as little as possible.
Page 23 of 26
6. Ordering Information
The TC-0710 is available in several configurations. Please contact your TechNexion sales contact window or distributor for options and availability details.
6.1. Custom Part Number Rule
The TC-0710 can be ordered in custom tailored configuration to meet special application requirements and conditions according to the following custom part number creation rules. Custom part numbers carry minimum order quantities (MOQ). Please connect with your TechNexion distributor or account manager for conditions and availability. Part number format:
TC0710-P-IMX6x-Rxx-Exx-xxxx-xxxx
Interface
Code
Description
PMIC
P
NXP MMPF0100
Processor
IMX6S
NXP i.MX6Solo
IMX6U
NXP i.MX6DualLite
IMX6D
NXP i.MX6Dual
IMX6Q
NXP i.MX6Quad
Memory R05
512MB DDR3
R10
1GB DDR3
R20
2GB DDR3
Storage E04
eMMC 4GB
E08
eMMC 8GB
EXX
eMMC other capacity
Wi-Fi / Bluetooth
- - 9377
Qualcomm QCA9377 802.11a/b/g/n/ac (2.4 + 5GHz) + Bluetooth 4.1
Custom ID
XXXX
Custom Part number ID for customized software loader and special component (BOM)
Page 24 of 26
6.2. Standard Package Contents
Item
Partnumber
Description
1
TC-0710
7 inch PoE HMI PCAP touch system with NXP i.MX6
2
Accessoires
6x mounting hooks
6x long screws (M3)
6x mounting posts
1x rubber O-ring
1x DC power latch cable (2-pin Micro-Fit 3.0)
NOTE: Standard pack contents might vary depending on your ordered configuration.
Page 25 of 26
7. Important Notice
TechNexion reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TechNexion terms and conditions of sale supplied at the time of order acknowledgment.
TechNexion warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TechNexion standard warranty. Testing and other quality control techniques are used to the extent TechNexion deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TechNexion assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TechNexion components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards.
TechNexion does not warrant or represent that any license, either express or implied, is granted under any TechNexion patent right, copyright, mask work right, or other TechNexion intellectual property right relating to any combination, machine, or process in which TechNexion products or services are used. Information published by TechNexion regarding third-party products or services does not constitute a license from TechNexion to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TechNexion under the patents or other intellectual property of TechNexion.
TechNexion products are not authorized for use in safety-critical applications (such as life support) where a failure of the TechNexion product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TechNexion products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TechNexion. Further, Buyers must fully indemnify TechNexion and its representatives against any damages arising out of the use of TechNexion products in such safety-critical applications.
TechNexion products are neither designed nor intended for use in military/aerospace applications or environments unless the TechNexion products are specifically designated by TechNexion as military grade or "enhanced plastic." Only products designated by TechNexion as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TechNexion products which TechNexion has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TechNexion products are neither designed nor intended for use in automotive applications or environments unless the specific TechNexion products are designated by TechNexion as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TechNexion will not be responsible for any failure to meet such requirements.
Page 26 of 26
8. DISCLAIMER
© 2001-2018 TechNexion Ltd. All Rights Reserved. No part of this document may be photocopied, reproduced, stored in a retrieval
system, or transmitted, in any form or by any means whether, electronic, mechanical, or otherwise without the prior written permission of TechNexion Ltd.
No warranty of accuracy is given concerning the contents of the information contained in this publication. To the extent permitted by law no liability (including liability to any person by reason of negligence) will be accepted by TechNexion Ltd., its subsidiaries or employees for any direct or indirect loss or damage caused by omissions from or inaccuracies in this document.
TechNexion Ltd. reserves the right to change details in this publication without notice. Product and company names herein may be the trademarks of their respective owners.
TechNexion Ltd. 16F-5, No. 736, Zhongzheng Road, ZhongHe District, 23511, New Taipei City, Taiwan Phone : +886-2-82273585 Fax : +886-2-82273590 E-mail : sales@technexion.com Web : https://www.technexion.com/
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use