(1/5)
User’s Manual
Product: WiFi+Bluetooth 4.1(HS) System on Module
Manufacturer: TechNexion Ltd.
Model: PIXI-9377
For Original Equipment Manufacturer integration only – this device cannot
be sold to the general public
FCC ID :2AKZA-QCA9377
IC:22364-QCA9377
General Specifications
Form Factor PIXI 16mm x 12mmx1.0mm Wireless SIP Module
MCU Qualcomm QCA9377-3
WLAN IEEE 802.11a/b/g/n/ac
Bluetooth Bluetooth 4.1(+ HS, BLE)
Bluetooth 2.1 + EDR/4.1: 2402MHz ~ 2480MHz
802.11b/g/n HT20 MHz: 2412MHz ~ 2462MHz
Frequency
Range
802.11a : 5180MHz ~ 5240MHz / 5745MHz ~ 5825MHz
802.11n HT20 MHz: 5180MHz ~ 5240MHz / 5745 ~ 5825MHz
802.11n HT40 MHz: 5190MHz ~ 5230MHz / 5755 ~ 5795MHz
802.11ac VHT80 MHz: 5210MHz / 5775MHz
Antenna 1x MHF4 connector
802.11n HT40 MHz: 2422MHz ~ 2452MHz
Host Interface
Voltage Input supply for host I/O: 3.3V
Signaling
Environment
Support
WLAN: SDIO 3.0
BT: UART/ I2S
WIFI control function through to SDIO interface
BT control function through to UART interface
Operating Temperature -40~85℃
Storage Temperature -40~135℃
(2/5)
User Manual with Statement required
FCC Statement:
FCC 15.119:
This device complies with Part 15 of FCC Rules. Operation is Subject to following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received including interference that cause undesired
operation.
FCC 15.105:
This equipment has been tested and found to comply within the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a different circuit from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
l Any changes or modifications not expressly approved by the party responsible for compliance could
void the authority to operate equipment.
l This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body
Modular Approval
OEM INTEGRATION INSTRUCTIONS:
This device is intended only for OEM integrators under the following conditions: 1) The module must be
installed in the host equipment such that 20 cm is maintained between the antenna and users, and 2) the
transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions
above are met, further transmitter test will not be required. However, the OEM integrator is still
responsible for testing their end-product for any additional compliance requirements required with this
module installed (for example, digital device emissions, PC peripheral requirements, etc.).
Any changes or modifications not expressly approved by the manufacturer could void the user's authority
to operate this equipment.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location
with another transmitter), then the FCC authorization for this module in combination with the host
equipment is no longer considered valid and the FCC ID of the module cannot be used on the final
product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization.
USERS MANUAL OF THE END PRODUCT:
The OEM integrator has to be aware not to provide information to the end user regarding how to install or
remove this RF module in the user's manual of the end product which integrates this module. The end
user manual shall include all required regulatory information/warning as show in this manual.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID: 2AKZAQCA9377
(3/5)
IC Statement:
RSS-Gen Issue 4 8.4
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following
two conditions: (1) This device may
not cause interference; and (2) This device must accept any interference, including interference that may
cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts
de licence. L'exploitation est autorisée
aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Co-located
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna
or transmitter.
Cet appareil et son antenne (s) ne doivent pas être situés ou fonctionner en conjonction avec une autre
antenne ou émetteur.
RSS-GEN 8.3 transmitters equipped with detachable antennas
This radio transmitter (identify the device by certification number) has been approved by Industry Canada
to operate with the antenna types
Antenna gain information: Dipole ANTENNA :4 dBi (2.4GHz),6 dBi(5GHz) and FPC ANTENNA 2.5 dBi
(2.4GHz),3 dBi(5GHz) listed with the maximum permissible gain indicated. Antenna types not included in
this list, having a gain greater than the maximum gainindicated for that type, are strictly prohibited for use
with this device.
Cet émetteur radio (identifiez le dispositif par numéro de certification) a été approuvé par
Industrie Canada pour fonctionner avec les types d’antenne
Informations sur le gain d'antenne: ANTENNE Dipolaire: 4 dBi (2,4 GHz), 6 dBi (5 GHz) et
ANTENNE FPC 2,5 dBi (2,4 GHz), 3 dBi (5 GHz) avec le gain maximal admissible indiqué. Les
types d'antennes non inclus dans cette liste, ayant un gain supérieur au gain maximum indiqué
pour ce type, sont strictement interdits pour cet appareil.
RSS-247 6.4(5) WLAN 11a
(i)the device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for
harmful interference to co-channelmobile satellite systems;
(iii) for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band
5725-5850 MHz shall be such that theequipment still complies with the e.i.r.p. limits specified for point-topoint and non-point-to-point operation as appropriate; and
Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of
the bands 5250-5350 MHz and5650-5850 MHz and that these radars could cause interference and/or
damage to LE-LAN devices.
(i) l'appareil pour fonctionner dans la bande 5150-5250 MHz est réservé à une utilisation en intérieur afin
de réduire les risques d'interférences
nuisibles à la co-canal systèmes mobiles par satellite;
(iii) pour les appareils avec antenne (s) détachable, le gain d'antenne maximal autorisé pour les
appareils dans la bande 5725-5850 MHz doit
être telle que l'équipement satisfait encore la pire limites spécifiées pour le point-à-point et non point-à-
point, le cas échéant; opération et
Devraient également être informés les utilisateurs que les radars à haute puissance sont désignés
comme utilisateurs principaux(c.-à-utilisateurs prioritaires) des bandes 5250-5350 MHz et 5650-5850
MHz et que ces radars pourraient provoquer des interférences et / ou
endommager les appareils LE-LAN.
(4/5)
IC Radiation Exposure Statement:
mobile device
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled
environment. This equipment should be
installed and operated with minimum distance 20cm between the radiator & your body.
Modular Approval
OEM integrator is still responsible for testing their end product for any additional compliance
requirements required with this module installed
(for example, digital device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop
configurations or co-location with another
transmitter), then the IC authorization is no longer considered valid and the IC No. cannot be used on the
final product. In these circumstances,
the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate IC authorization.
End Product Labeling of Modular
This transmitter module is authorized only for use in device where the antenna may be installed such that
20 cm may be maintained between
the antenna and users. The final end product must be labeled in a visible area with the following:
“Contains transmitter module IC: IC:22364-QCA9377
(5/5)
Loading...