Technaxx TX-111 User Manual

Technaxx® * User Manual
WiFi Rear Camera System TX-111
Suitable for most of cars (& vans, SUVs, minibuses, caravans, etc.)
as assistance for reverse parking.
This system should be an aid and should NOT replace the need to drive
NOTE: the Smartphone in the car may only be used if it is firmly fixed in
a holder.
Under no circumstances will the manufacturer or supplier accept any
responsibility or can held liable for any direct or indirect, incidental or
consequential damage, or for injuries resulting from installing or use of
this system.
The manufacturer Technaxx Deutschland GmbH & Co.KG hereby declares
that this device, to which this user manual belongs, complies with the
essential requirements of the standards referred to the Directive RED
2014/53/EU. The Declaration of Conformity you find here:
www.technaxx.de/ (in bar at the bottom “Konformitätserklärung”). Before
using the device the first time, read the user manual carefully.
Keep this user manual for future reference or product sharing carefully. Do the same with the original accessories for this product. In case of warranty, please contact the dealer or the store where you bought this product. Warranty 2 years
Features
Inconspicuous reversing camera in license plate holder Suitable for most vehicles as assistance for reverse parking Video stream over WiFi on Smartphone via APP (New Sight) Wireless video transmission up to ~10m IR LED for clear night vision ~4m Adjustable camera alignements & 110° viewing angle IP67 camera protection class (dustproof & protection against
temporary immersion) License plate holder suitable for single-line EC registration (52x11cm)
Complete installation set More safety in reverse driving
Technical specifications
License plate holder with camera
Image sensor / Resolution CMOS / 640x480 pixel Viewing angle 110° Min. illumination 0.5Lux / automatic white balance IR night vision distance ~4m Power supply Connection via WiFi transmitter Max. current 210mA (incl. transmitter) Protection class IP67 Weight / Dimensions 264g / (L) 52.8 x (W) 4.0 x (H) 13.7cm
WiFi Transmitter
Modulation
(CCK, DQPSK, DBPSK), OFDM (BPSK,
QPSK, 16QAM, 64QAM) Protocol IEEE 802.11 b/g/n Encoding WPA2 Transmission frequency 2.4GHz Max. radiated output power 10mW Weight / Dimensions 72g / (L) 9.5 x (W) 4.0 x (H) 1.4cm Input voltage DC 12V Transmission distance ~10m open space (no interferences) Operating temperature –10°C up to +50°C
New Sight / iOS version 7.0 and higher and
APP name / version
Android version 4.4 and higher
Weight / Dimensions 65g / (L) 9.0 x (W) 3.5 x (H) 1.2cm
License plate holder with camera, WiFi transmitter
Packing
with power connection for the camera, Mounting
Contents
material, User Manual
Hints for Environment Protection: Packages materials are raw materials and can be recycled. Do not disposal old devices or batteries into the domestic waste. Cleaning: Protect the device from contamination and pollution (use a clean drapery). Avoid using rough, coarse-grained materials or solvents/aggressive cleaner. Wipe the cleaned device accurately. Distributor: Technaxx Deutschland GmbH & Co.KG, Kruppstr. 105, 60388 Frankfurt a.M., Germany
Product overview
The rear view camera sends a video signal from the camera via WiFi to the smartphone. In case another Bluetooth handsfree device is installed in your vehicle, it works in the same frequency range as the camera. If that handsfree device is activated, it may cause disturbances. Therefore we recommend to deactivate that other Bluetooth handsfree device while using the reversing system.
License plate holder with camera
1 Infrared-LED 3 Holder 2 Camera 4 Connection cable
WiFi Transmitter
1 Connection cable to the
2 Connection cable to camera
electrical system
WiFi status LED on the WiFi transmitter box:
RED: WiFi is being set up GREEN: WiFi is ready for connection
Commissioning
Check the functionality of the components before installation (a installed product is excluded from the return). Preparing and installing the license plate holder and the transmitter unit. NOTE: You may need a voltmeter to measure the polarity of the electrical system.
Break the two locks carefully out of the holder.
Remove the transport locks carefully. Use a sharp knife or a
tong.
 Attach the license plate holder to the vehicle instead of your previous license plate holder.  Insert the camera cable into the trunk compartment and connect it to the transmitter unit.  Attach the transmitter unit steady and firm in the trunk compartment.  Connect the black connection cable of the WiFi transmitter to the negative pole of the 12V electrical system (on board-voltage).
 Connect the red connection cable of the WiFi transmitter to the positive pole of the 12V electrical system (on board-voltage). You can use any 12V voltage that is switched on or off with the ignition or the light (rear light). A connection with 12V continuous plus is not recommended because of the power consumption. It is also not recommended to connect to the reversing light as the WiFi transmitter will take about 10 seconds to establish a connection.
Using the cable clamps
The pictures explains how to use the supplied cable clamps.
1. Put the cable from
2. Insert the 2nd
3. Close the clamp.
the car you want to
connect the WiFi
transmitter with into
cable (red or black
cable of the WiFi
transmitter).
the clamp.
Insert the license plate in the holder
The following drawings show in sequence the insertion of the license plate.
1. Step
Slide the license plate into the upper opening.
 Press the number plate towards the holder.
2. Step
 Slide the license plate down until it stops.
3. Step
 Insert the locks from above into the holder.
(You carefully broke them out of the holder in the first step.)
 Set the camera at an angle where you have a good view to the rear, depending on the height of the license plate holder from the ground.
The displayed lines on the Smartphone give you an indication of the distance.
Definitely control the distance with a folding ruler. Explanations for the installation of the Smartphone APP can be
found on the following pages.  Then tighten the screws on both sides of the camera.
Download & install the APP
For the TX-111 you get for Apple iOS (from 7.0) and Android (from
4.4) a suitable APP.
iOS: Download and install the APP
Open the APP-Store or Scan the QR­code.
In the search field enter New Sight. Select New Sight under the search
results and confirm with Install. After the app is installed, you will see a corresponding icon
Setting up the WiFi connection:
Go to Settings of your Smartphone. Open WiFi.
.
Select WIFICAMERA as WiFi connection.
At initial startup, enter the following dialog as Password 88888888 (8x8).
The connection is made.  Open the APP New Sight.
Android: Download and install the APP
Open the Playstore or Scan the QR­code.
In the search field, enter New Sight. Select New Sight under the search
results and confirm with Install. After the app is installed, you will see a corresponding icon on the screen.
Setting up the WiFi connection:
Go to Settings. open WiFi. In the WiFi list, select WIFICAMERA. At initial startup enter the password
88888888 (8x8).
The connection is made.  Open the App New Sight.
Start/Open the APP New Sight
Take a snapshot of the current live view
List of taken and saved pictures on your Smartphone.
Take a video of the current live view.
List of taken and saved videos on your Smartphone.
Horizontal reflection (mirror) of the live view Customize the WiFi name and WiFi password of the WiFi
transmitter. It is suggested to change the name and the password after the first use. After changing WiFi name and password you need to reconnect your phone to the new WiFi. Enter the new given password.
Tips, Note & Attention
A brief tap on the display will hide the menu. The displayed lines are intended only as an aid to estimating the
distance. To get a feel for it, you should do a driving exercise. When transferring the images, there is a systemic delay. This delay is in the range of one-half to one second. They should take this time into consideration when driving backwards.
Problem and solution
You will only get a gray picture, even though the LED on the WiFi transmitter box is green.  In this case, you should reset the WiFi transmitter box. Press with a pen into the marked RESET button on the WiFi transmitter.
WiFi Status
1 Reset 2
RED: WiFi is being set up
GREEN: WiFi is ready for connection  Then disconnect the power supply and restore the connection after approx. 20 seconds. Check if the WLAN connection is available again. NOTE: In some cases it may also be necessary to uninstall and reinstall the App New Sight.
Safety regulations
The reversing system is an aid and does not relieve the driver of his duty of care in road traffic according to STVO. Please read these instructions carefully before first use.
General information:
Never place the device on an unstable surface. Dropping may damage the device. The device is not in the hands of children. It is not a toy. Also observe the safety instructions and the operating instructions of the other devices to which the device is connected. In commercial facilities, the accident prevention regulations of the Association of Professional Associations for Electrical Installations and Equipment must be observed. In schools, training centers, hobby or self-help workshops, the operation of electronic products is to be monitored responsibly by trained personnel. The seller assumes no responsibility for damage that occurs during the use of the device, as well as for complaints by third parties.
Environmental conditions:
Avoid heavy mechanical stress on the device. Protect it from vibration, hard knocks, do not drop it or shake it. Do not expose the device to high temperatures (over 50°C) and strong temperature fluctuations. Protect it from direct solar radiation and proximity to radiators. IP67 camera protection class (dustproof & protection against temporary immersion). The monitor and the transmitter may only be operated indoors. It cannot be completely ruled out that some paints, plastics or other care products attack the material of the housing or accessories.
Disorders: If an object or liquid gets into the device, have the device checked by an authorized technician before continuing to use it. We recommend that you contact our service center. Packing material: Keep children away from packaging material. There is danger of suffocation. Cleaning and care: Always store the device in a clean, dry place when not in use. Use a dry, soft cloth to clean the exterior surfaces. Interference by wireless transmission: The device operates at a frequency of 2468 MHz. This frequency can also be used by other devices that transmit video wireless. It can thus come in individual cases to disturbances.
Service phone No. for technical support: 01805 012643 (14 cent/minute from
German fixed-line and 42 cent/minute from mobile networks).
Free Email: support@technaxx.de
Enjoy your product * Share your experience and opinion on one of the
well-known internet portals.
Loading...