Technaxx Easy IP-Cam Socket Full-HD TX-57 User manual

® *

Technaxx

User Manual

Easy IP-Cam Socket FullHD TX-57

(Camera for a socket)

This device complies with the requirements of the standards referred to the Directive

R&TTE 1999/5/EC. The Declaration of Conformity you find here: www.technaxx.de/ (in

bar at the bottom “Konformitätserklärung”). Before using the device the first time, read the

user manual carefully. Service phone No. for technical support: 01805 012643 (14

cent/minute from German fixed-line and 42 cent/minute from mobile networks).

Free Email: [e-mail]

Content

Content................................................................................................................................1

Features...............................................................................................................................2

1. Device structure...............................................................................................................2

2. Initiate Easy IP-Cam........................................................................................................3

Install Easy IP-Cam..........................................................................................................3

Access AP Mode..............................................................................................................3

3. Setup Easy IP-Cam .........................................................................................................3

Install Technaxx Easy IP App ...........................................................................................3

Add Camera ( ).............................................................................................................3

Easy Mode Add Camera..................................................................................................4

Monitor Camera ...............................................................................................................5

Advance Function ............................................................................................................5

Camera list ( )...............................................................................................................5

Event list ( )..................................................................................................................5

Photos/Videos ( ) .........................................................................................................6

Camera Settings ( )......................................................................................................6

4. Event Record...................................................................................................................6

Monitor Event Detection...................................................................................................7

View Event Record...........................................................................................................7

5. Technical specifications ...................................................................................................8

GNU GENERAL PUBLIC LICENSE ............................................................................9

Preamble .....................................................................................................................9

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION10

1

Features

 Ideal for viewing and monitoring rooms and other indoor locations
 Easy power supply over a socket - no power cable needed
 Push notification via APP when motion detection
 FullHD video resolution 1080P (1920x1080), 30fps
 IR LED for night lighting & ambient light sensor
 2MP CMOS image sensor & PIR sensor
 P2P Cloud monitoring camera
 Easy setup at iOS/Android device by QR code scanning
 Built-in microphone for audio recordings, iOS & Android APPs

for live monitoring & recording & playback

1. Device structure

1 Lens
2 PIR Sensor
3 Microphone
4 Light Sensor
5 Exchangeable AC Plug

1 IR LED
2 Ready LED
3 Status LED
4 MicroSD Card Slot
5 Reset Button

2

2. Initiate Easy IP-Cam

The Easy IP-Cam has a built-in WIFI chipset and can directly connect to your home WIFI
network. Therefore, for the first time use the Easy IP-Cam, you need to set up the WIFI
network and assign an available network which can link to the internet for the camera from
the AP (Access Point) Mode.

Install Easy IP-Cam

Insert a MicroSD card in the MicroSD card slot max.32GB.
Insert the AC Plug of the camera to the wall AC outlet and the Easy IP-Cam turns on.
Adjust the camera up or down to the applicable angle.

Note:

1. The Easy IP-Cam has no built-in battery. If you take out the camera from the AC outlet,

the camera will be offline and turns off.

2. All settings have saved in camera even power off. When the power supply restore, the

camera will turn on and reconnect to the set WIFI network automatically.

Access AP Mode

If the Easy IP-Cam was never be used. It will enter the AP Mode directly.
The RED Status LED lights on for about 8 seconds to initiate. After that it flashes slowly for 20 or
more seconds and active the WIFI function.
The Ready LED flashing fast in GREEN when the camera enters the AP Mode.

Note: Press the Reset Button to restore the default setting of camera in AP Mode.

3. Setup Easy IP-Cam

Install Technaxx Easy IP App

Search and find the Technaxx Easy IP App from the Apple Store for iOS or the
Google Play for Android. Then install it in your mobile device. Press the Easy IP
icon to start it.

Add Camera ( )

Press the Add Camera icon
camera body. Use the QR Code Reader to read the UID of camera.

Enter UID Password "888888" and name (customizable) the camera.

to add camera. Find the UID QR Code Label on the

3

Enter the password of WIFI network which the camera can link to the internet and press

.

For iOS:

1. Press the Home button and select the Settings, go to the WIFI network then check

"CamAP" and no need to enter password.

2. Wait around 60 sec. and make sure you see

appear.

3. Press Home button again and go back to Easy IP app.

Camera reboots within 60 sec. and the Green LED turns on steady.
Update or change the device password and then press .

Easy IP is connecting to the camera and ready for monitoring from your Smartphone when
camera is online. Please press the “OK” button when you see a popup notification during
connection process!

Note:

1. The maximum of 16 cameras can be added in the App.

2. If the assigned WIFI network of the camera has been changed, the camera must use the AP

Mode to set the new assigned WIFI network again.

3. Make sure the assigned WIFI has enough bandwidth otherwise the camera is hard or

need longer waiting time to access the internet.

Easy Mode Add Camera

As long as the Easy IP-Cam has initiated the WIFI network from the AP Mode. You can use
the Easy Mode to add this camera in other mobile device and monitor it from Easy IP App.

Press the Add Camera icon
body. Use the QR Code Reader to read the UID of camera.

Enter Camera Password then press .

Note: This password must use the same as the new password which has be changed in
the AP Mode.

to add camera. Find the UID QR Code Label on the camera

4