Technaxx
* User Manual
Car Power Inverter with 2 USB Ports TE13
Do not use electric charge that need higher watts than
maximum 200W continuously !
This device is only suitable for CARS !
The Declaration of Conformity for this device is under the Internet link: www.technaxx.de/
(in bottom bar “Konformitätserklärung”). Before using the device the first time, please read
the user manual carefully. Service phone No. for technical support: 01805 012643 (14
cent/minute from German fixed-line and 42 cent/minute from mobile networks). Free Email:
support@technaxx.de
Features
Charges various electronic devices in a car (12V cigarette ligher socket)
2.1A USB port & 1A USB port
Schuko Plug with illuminated power switch
Converts 12V DC battery power into standard 230V AC (household) power, to run a
variety of electronics, e.g. tablets, smartphones, laptop computers, game systems, small
TVs, DVD/MP3 players, camping accessories, GPS units and much more
Output power 200W (max. continuous) and 400W (peak)
Plug into a cigarette lighter socket of a car
Automatic safety shutdown to secure the car battery (at ~10.5V)
High/Low voltage & overload protection
Overheating protection (built-in ventilation fan)
Durable plastic housing fits into a cup holder of a car
®
Technical specifications
Output power 200W (maximum, continuously), 400W (peak)
Input voltage (DC) 12 (cigarette lighter socket of a car)
Output voltage / AC frequency 230V / 50Hz nominal
Output Waveform PWM Sine Wave The power inverter’s PWM [Pulse
Width Modulated] sinusoidal wave is suitable for
almost all electric/electronical devices with max. 200W
Low battery voltage shutdown at ~10.5V
USB output ports (DC) 1x 5V/2.1A and 1x 5V/1A
AC output 1x Schuko port
Circuit protection (DC overload) 20A external car fuse (replaceable)
Weight / Dimensions
Package Contents Car Power Inverter with 2 USB Ports TE13, 20A Fuse,
400g / (H) 10.0–5.5 x (L) 7.0 x (W) 17.2cm
Cable length 90cm
User Manual
Operation
Before using the power inverter determine your equipment’s total watts!
Do not connect more watt than the Output Power (maximum continuous watt) of the
device ( see technical specifications). See below table for typical equipment running
times and for important notes concerning the limitations of car’s electrical systems.
Watt ratings are usually listed in equipment manuals or on nameplates. If your equipment
is rated in Amp, multiply that number times AC utility voltage to determine watts.
(mathematic example: a drill requires 1.5A 1.5A x 230Volt = 345Watt. This is way to
much to work with a drill. Now follow these steps:
Step 1: Plug the device into the cigarette lighter socket / accessory outlet of your car.
Step 2: Turn on the power switch of the device.
Step 3: Plug equipment into the Schuko port of the device.
Note: Power switch can be off when you only use the USB output ports.
Typical running times before battery recharge
Although you can operate your device with your car’s engine off. Best results are usually
achieved with the car’s engine running. Since the device only converts electrical energy
and does not produce it, it’s performance is relative to the condition of the car’s electrical
system (battery, alternator and wiring). If other electric charges (e.g. air conditioner, heater,
lights, etc.) using power also, you may get less running time.
Compact Car
(4 cylinder)
Half load
(engine on/engine off)
Full load
(engine on/engine off)
Continuous /
~ 4–6 hours
Continuous /
~ 2–3 hours
Mid-size Car
(6 cylinder)
Continuous /
~ 6–8 hours
Continuous /
~ 3–4 hours
Mid-size Car
(8 cylinder)
Continuous /
~ 8–12 hours
Continuous /
~ 4–6 hours
Cars electrical system limitations
Due to the limitations of certain cars DC 12V cigarette lighter socket / accessory outlet
electrical systems, you may not be able to continuously run a full elctric charge from the
device. If you regularly blow fuses, it may indicate your car is not adequately wired to
support the device as it is designed. In this case, consult car manufacturer
recommendations for rewiring from the fuse block or battery with appropriate wiring (10–12
gauge) and fusing (at least 40A).
Maintenance
This device requires no maintenance and contains no user-serviceable parts (except for
replaceable DC fuses, where applicable). Maximum output power (continuous or peak) only
available when car’s battery is properly charged. Run car ’s engine often to maintain proper
charge. Peak output power is instantaneous. Replace fuse only with a fuse of equal
amperage rating. Do not use higher-rated fuses.
Troubleshooting
(1) Device does not turn on when power switch is turned ON.
Device shut down automatically due to low battery voltage (at ~10.5V). Turn the
device OFF and start yours car’s engine to recharge the car’s battery. Only use this device
with the car’s engine running.
Device shut down automatically to output overload. Turn the device OFF and remove
overload by unplugging high-watt devices. Electric charge should not exceed the device’s
maximum continuous output power (see technical specifications).
Blown fuse Replace the fuse with standard automotive fuse of identical amperage
where applicable (see technical specifications).
(2) Device is unable to power connected equipment.
Battery running low. Low battery voltage reduces the device’s power output. Turn t h e
device OFF and start yours car’s engine to recharge the car’s battery. Only use this device
with the car’s engine running.
(3) Connected equipment experience audio/video distortion.
Loose connections Check and secure all connection.
Audio/Video interferences Reposition equipment antennas and the device.
Warnings & Caution
Use of the device in life support applications where failure of the device can reasonably
be expected to cause the failure of the life support equipment or to significantly affect its
safety or effectiveness is not recommended. Do not use the device in the presence of a
flammable anesthetic mixture with air, oxygen or nitrous oxide, and also not near flammable
materials, fumes or gases. Since the device requires adequate ventilation during
operation, do not block fan or cooling vents and do not cover the device. Do not operate
near car heating vents or in direct sunlight. Keep the device dry at all times and
disconnect when not in use. Turn OFF connected equipment before (!) starting your
engine. DO NOT plug a surge protector, line conditioner or UPS system into the device. If
you attach AC extension cords, use the heaviest practical gauge. Before connecting a
battery charger or adapter, check its manual to make sure that the technical specifications
of the device (including output waveform) fall within the recommendations of the external
battery charger or adapter.
Hints for Environment Protection: Packages materials are raw
materials and can be recycled. Do not disposal old devices or
batteries into the domestic waste. Cleaning: Protect the device from
contamination and pollution (use a clean drapery). A void using rough,
coarse-grained materials or solvents/aggressive cleaner. Wipe the
cleaned device accurately. Distributor: Technaxx Deutschland
GmbH & Co.KG, Kruppstr. 105, 60388 Frankfurt a.M., Germany
Loading...