Techly I-ALARM-KIT001 Installation Manual

WIRELESS

GSM/APP

www.techly.com

Installation manual

SMS/GSM Alarm Wireless Starter kit

UP TO 159

ACCESSORIE

DE ITFR

Features

- GSM transmitter

- Supports up to 10 remote controls, 99 wireless accessories and 50 RFID tags

- Can store up to 5 phone numbers, 5 SMS numbers

- Arm / disarm the system by SMS, phone call, or App (on iOS or Android)

- Can be disarmed by RFID tag

- Call function from the panel

- SMS alerts for power failure, power recovery and low battery

- Audio surveillance of the site from distance

- 2 x 800mAh lithium batteries included (8h battery life in standby mode)

Specications

Product name

I-ALARM-KIT001

SKU

I-ALARM-KIT001

Control panel power supply

Input: AC 110-240V / 50-60 Hz Output: DC 12V / 800 MA

GSM working frequency

850 / 900 / 1800 / 1900 mHz

Radio-frequency

433.92MHz (±75KHz)

Transmission distance

80m in open space

Standby current

80ma

Alarm current

300mA

Backup batteries

Lithium Batteries: 3.7V / 800 mAh x 2 (BL-5B) (8h battery life in standby mode)

Internal siren

95dB

Housing material

ABS plastic

Operating conditions

Temperature: -10°C~55°C

Humidity: ≤ 80% (non-condensing)

Control panel dimensions (L x W x H)

188 x 125 x 25 mm

Box content

Control Panel x1 Motion Detector x1 Door / Window Contact x1 Remote Controls x2 RFID Tags x2

AC Adaptor x1 User manual x1

DE ITFR

www.techly.com

Control Panel Layout (Front)

Control Panel Layout (Back)

Plans and position the alarm system

Power On/O

Adapter interface 24h Zone Electronic

lock

Wired siren

GND

SPK

LOCK

Z1 +12V GND

Call

Clear

RFID Reader Home Mode

LCD Display

Disarm

Record

Arm

SOS

Monitoring MIC

Speaker

Power Supply Interface

Tamper Switch

Power Switch

Battery Compartment

SIM Card Slot

Control panel

Remote control

Outdoor siren

Zone Sensor 1: "Front door"

Zone Sensor 2: "Living room PIR"

Zone Sensor 3: "Entrance window"

Zone Sensor 4: "Terrace Window"

Zone sensor 5: "Terrace door"

Zone sensor 6: "Bedroom Window"

Zone Sensor 7: "Bedroom PIR"

Zone Sensor 8: "Gas kitchen"

Zona sensor 9: "Bath water"

www.techly.com

DE ITFR

Quick Start-up Guide

Connect your System

Using the GSM transmitter (SIM card)

Open the battery compartment at the back of the control panel and insert a SIM card in the control panel.

Important

Before using the Alarm System in GSM mode, you need to purchase a SIM card that works on the GSM network with 850 / 900 / 1800 / 1900 MHz frequency. We recommend you to subscribe to a plan with unlimited texts and one hour of voice. For more information, please contact your local reseller.

Important

Make sure the SIM card does not require any PIN code. For more information, please contact your local reseller.

Turning your System on

1. Plug the AC adaptor to an AC socket.

2. Plug the output connector of the AC

adaptor into the adaptor interface in the battery compartment at the back of the control panel.

3. Turn the power switch to "ON" (in the

battery compartment at the back of the control panel).

DE ITFR

www.techly.com

Mount the Control Panel

Before mounting the control panel on the wall, make sure the reception of the

GSM signal is sucient.

Fix the wall-mounting bracket on the wall with screws. Wedge the panel on the

bracket, make sure they t well.

Basic Operations

Arm the System

Press the Arm button " " on the control panel. The control panel beeps once: the system is armed. The LCD display indicates "Armed" and the Arm icon on the control panel is lit.

Note

If the Entry / Exit Delay is activated, all zones except the 24h zone will be armed after the delay set (refer to the instructions on page 10 of this manual “Entry / Exit Delay”).

Disarm the System

Type your user code and press the Disarm button "

" on the control panel. The

control panel beeps twice: the system is disarmed.

Home Mode

Press the Home button " " on the control panel. The control panel beeps once: the system is armed in Home Mode.

All the sensors assigned to the Normal zone are armed. The sensors assigned to the Home zone are disarmed.

Emergency Mode

Hold the “#

SOS

” button for 3 seconds. The alarm is triggered immediately and the siren rings out. At the same time, the control panel dials the stored phone numbers.

DE ITFR

Speed Dial

Press the Call button “ ” on the control panel for 3 seconds: the panel auto-dials the rst stored phone number. Press the Call button “ ” to end the call.

Hands-free Phone Call from the Panel

Through GSM

Press the Call button“ ” on the control panel, type the phone number you wish to call and press the Call button “ ” again.

Record / Play a Voice Memo

Long press the Record Voice Memo button to record a 10-second voice message. The Play Voice Memo Button blinks when a message has been recorded. Push the center of the RFID reader in the control panel to listen to the voice memo. The

LED indicator turns o when the voice memo is being played. Touch it again to

replay the memo.

Hard Reset

Turn the control panel on. Press the tamper switch at the back of the control panel 5 times wirthin 5 seconds after having turned it on.

Settings will be restored to default values. Stored phone numbers and connected accessories will be cleared.

DE ITFR

www.techly.com

Setup from the control panel

The Alarm System must be set up before using for the rst time. During the setup

of the system, the control panel can be powered either by the AC power adapter or by the backup batteries.

Default codes

- Admin code (necessary to set up your system): 123456

- User code (necessary to disarm your system or stop the alarm): 1234

- Duress code: 1111 (enables you to trigger a duress alarm)

- Open door code: 8888 (enables you to open an electronic door lock plugged to

your control panel)

All access codes can be changed. We recommend you to change these codes before using your system for the rst time.

The control panel of your alarm system features an LCD display that enables you to navigate through the menu of the control panel and set up your alarm system.

To enter the setting menu, type [your admin code + Enter] on the control panel.

In the table on the next page, each column represents a menu or a sub menu. Each menu or submenu will be displayed on one of the two lines of the LCD display. On the LCD display, the current menu, submenu, or setting is shown on the line at the bottom, while the previous menu or submenu is shown on the line at the top.

Navigate and select the setting you wish to modify with the keys “

” or “ ”, and

enter each menu or sub menu by pressing “Enter”.

How to use the keyboard

“ ” = delete “ ” = move forward “ ” = move backward “Enter” = select / conrm “Esc” = back / previous step in the menu / cancel

The tables on the next pages summarize all the settings that can be accessed and

modied on the control panel.

DE ITFR

Main Menu Sub Menu 1 Sub Menu 2 Sub Menu 3

Phone numbers

Phone [1~5] is:

SMS Num [1~5] Is:

Accessories

Remote & Keypad

Add a new 01/10 30

Delete All 1=YES 0=NO

Delete a Remote Input 01-10:

Accessories

RFID Tag

Add a new 01/50 30

Delete all 1=YES 0=NO

Delete a Tag Input 01-50:

Accessories

Wireless

Sensors

Add a new

Home Zone Delay Zone

Normal Zine

24-H Zone

Delete all? 1=YES 0=NO

Delete a Sensor Input 01-99:

Accessories

Test Mode

DE ITFR

www.techly.com

Comments

Select the phone or SMS number you want to edit, type in the phone number and conrm with

the key "Enter". Use the key "

" to clear.

5 phone numbers and 5 SMS numbers can be stored in the control panel.

The LCD screen displays “01/10” (at the left), which indicates the number of the remote control you are about to connect (01 is the current remote control, 10 is the total number of remote controls you can connect), and "30" (at the right), which indicates the time remaining to connect the remote control. Press any key on the keypad or remote control, you hear one beep: the connection is successful.

Once the remote control has been added, the countdown starts over from 30 so that you can register another remote control in control panel (up to 10 remote control can be registered in the control panel). Press Esc to exit.

Enter the number of the Remote Control you wish to delete and press "Enter".

The LCD screen displays “01/50” (at the left), which indicates the number of the RFID tag you are about to connect (01 is the current RFID tag, 50 is the total number of tags you can connect), and "30" (at the right), which indicates the time remaining to connect the RFID tag. Swipe the RFID tag in front of the RFID reader, you hear one beep: the connection is successful.

Once the RFID tag has been added, the countdown starts over from 30 so that you can register another RFID tag in control panel (up to 50 tags can be registered in the control panel). Press Esc to exit.

Enter the number of the RFID tag you wish to delete and press "Enter".

Select the sensor type you wish your sensor to be assigned to (Normal Sensor, 24 Hour Sensor, Delay Sensor, or Home Sensor), press “Enter” to conrm. For more information on zone setup, please refer to page 14 of this manual.

The LCD screen displays “01/99” (at the left), which indicates the number of the sensor you are about to connect (01 is the current sensor, 99 is the total number of sensors you can connect), and "30" (at the right), which indicates the time remaining to connect the sensor. Trigger the sensor, you hear one beep: the connection is successful.

Once the sensor has been added, the countdown starts over from 30 so that you can register another sensor in control panel (up to 99 sensors can be registered in the control panel). In such case, the sensor will be added to the same zone. Press Esc to exit.

Enter the number of the sensor you wish to delete and press "Enter".

Trigger the sensors you have previously connected to the control panel. You hear 1 beep, the LCD screen displays the signals that have been respectively sent by each sensor triggered. Make sure all the sensors you have triggered are mentioned on the LCD screen. Press “Esc” to exit the test mode.

This mode enables you to test if the sensors have been connected successfully to the control panel.

DE ITFR

Main Menu Sub Menu 1 Sub Menu 2 Sub Menu 3

System Setting

Date and Time

YYYY-MM-DD TIME

System Setting

Date Format

System Setting

Entry Exit Delay

Entry Delay 000-300

Exit Delay 000-300

System Setting

Auto Arm / Disarm

Auto Arm Time <00:00>

Auto Disarm Time <00:00>

ON or OFF?

System Setting

Control by Phone

ON or OFF? -

System Setting

GSM Fail Alarm

ON or OFF?

System Setting

Keypad tones

ON or OFF? -

System Setting

Access code

Admin Code 123456

User Code 1234

Duress Code 1111

Open Door Code 8888

DE ITFR

www.techly.com

Comments Note

(e.g. 2014-06-20 14H30)

This function can be used if you do not want to bring a remote control or RFID tag with you. When the system is armed, you hear one beep every second to remind you to leave. The beep rhythm speeds up during the last 10 seconds. If an intruder is detected, the alarm will be delayed accordingly.

Time is calculated in seconds. The Entry and Exit Delay can be set from 0 to 300 seconds.

The entry and exit delays only work for sensors connected as Delay Zone accessories (see "Wireless" on page 8).

The Entry Delay gives you time to disarm the system on the control panel without triggering an alarm. The Exit Delay gives you time to arm the system on the control panel and leave your home without triggering an alarm.

You can set up the system to arm and disarm

automatically at a dened time every day.

Setting Auto Arm and Auto Disarm to the exact same time will deactivate the function.

You can activate or deactivate the control of your system by phone call. Activating the control by phone call enables you to arm and disarm the system and monitor your home by phone call.

See instructions on page 14 for more information on the control of the system by phone call.

Notication of SIM/ GSM signal problem.

Activate or deactivate the sound when typing on the keyboard of the control panel.

Your admin code enables you to enter the setup menu. Default admin code: 123456

It is recommended to change all codes before using your system

for the rst time and to keep

your codes secret

Your user code enables you to disarm the system on the control panel. The user code is the access code requested when you call the control panel. Default user code: 1234

In case of emergency, when you are requested to disarm the system by force, it is recommended to disarm your system with your Duress Code. The panel will silently dial the stored phone numbers. Default duress code: 1111

You can open electronic doors using this code. The door must be wired to the [LOCK] interface on the back of the control panel.

DE ITFR

Main Menu Sub Menu 1 Sub Menu 2 Sub Menu 3

System Settings

Ring Times

<1-9>: 5 -

System Settings

Siren Alert Time

<1-9Min>: 3

System Settings

Backlight Time

<0-120s>: 30 -

System Settings

Siren Setup

Wired Siren

Siren Switch

ON/OFF

Arm/Disarm Tone

ON/OFF

Built-in Siren

Siren Switch

ON/OFF

Arm/Disarm Tone

ON/OFF

Wireless Siren

Siren Switch

ON/OFF

Arm/Disarm Tone

ON/OFF

System Settings

User ID

On / O -

Disarm Upload

On / O -

System Settings

Call Recycle

<1-9>: 3

System Settings

Language

- -

System Settings

Reset

1=YES 0=NO -

System Settings

About

About Jun 4 2014 -

History

- -

DE ITFR

www.techly.com

Comments Note

Enter the value (from 1 to 9) and conrm with "Enter".

This function enables you to determine the number of times the control panel will ring before taking your call (for control by phone call).

Enter the value (from 1 to 9) and conrm with "Enter".

This function enables you to determine for how long the siren rings out in case of alarm.

Enter the value (from 0 to 120) and conrm with "Enter".

Default setting is 30 seconds.

Enable / Disable the siren. Default setting: On

Wired siren refers to a siren connected to the control panel by wire.

Arm / Disarm silently. Default setting: On

Enable / Disable the siren. Default setting: On

Built-in siren refers to the siren featured in the control panel.

Arm / Disarm silently. Default setting: On

Enable / Disable the siren. Default setting: On

Wireless siren refers to a siren connected to the control panel by radio-frequency.

Arm / Disarm silently. Default setting: On

When Disarm Upload is on, the system will upload the history of arm/disarm events to the to the CMS.

hen the alarm is triggered, the control panel dials the numbers you have stored. If you do not disarm the system, the control panel will call you again (up to 9 times). The “Call Recycle”

function enables you to dene the number of times the control

panel attempts to call you. Default setting:

3 times.

Select the language you wish to choose and conrm with

"Enter".

Languages available may vary depending on the version of your product.

All system settings will be restored to default setting. Stored phone numbers and connected accessories will be cleared.

Choose the event log you need to track, press “Enter”.

The control panel keeps in record the latest 150 event logs.

DE ITFR

Zone setup of accessories

Every detector can be assigned to 4 dierent categories of zones: Home Zone,

Delay Zone, Normal Zone and 24-H Zone. To assign a detector to a zone, follow the instructions on page 8 of this manual (the zone will be assigned at the time of connection of the accessory).

Normal zone

When the system is armed, if a sensor is triggered, the siren rings out. When the system is disarmed, sensors do not trigger an alarm.

24h zone

Regardless the system is armed or disarmed, sensors assigned to the 24h zone can trigger an alarm. It is recommended to assign smoke detectors, gas detectors and outdoor beam sensors to the 24-H zone.

Delay zone

If you want to set up the entry and exit delay functions, corresponding sensors must be assigned to the Delay zone. Once the delay time has been set up, the sensors will not trigger the alarm during the delay set. Refer to the instructions “Entry and Exit Delay” on page 10 of this manual. It is recommended to assign the Door / Window Contact to the Delay zone.

Home zone

When the system is armed in Home Mode, the sensors assigned to the Home zone do not trigger an alarm. It is recommend to assign motion dectors to the Home zone so that you can have your system armed in Home Mode when you are home and move inside your home without triggering any alarm.

Control by phone call

This feature is available only after having enabled it from the control panel, as explained on page 10 of this manual.

Method 1

When an alarm has been triggered, the control panel dials the stored phone numbers. When you pick up the phone, follow the voice instructions to control the panel from distance (refer to the instructions in the table below).

Method 2

1. Dial the telephone number of your control panel (either the number of the SIM card in your control panel or the number of the landline to which your panel is connected). After getting through, the voice instructions will guide you to enter your access code.

2. Enter your user code, followed by “#”.

3. A voice gives you the options you can select.

4. Select the operations to control the panel (see instructions in the table below).

DE ITFR

www.techly.com

Note

The call will end automatically if you do not send any command within 30 seconds.

Table of commands for control by phone call

Command Function

Press “1” Arms the system

Press “0”

- Disarms the system and turns the

siren o

- Stops monitoring without hanging up

- Stops the phone call function without hanging up

Press “3” Phone call with control panel

Press “

”

- Starts audio monitoring mode (not limited in time)

- Stops the built-in siren and the wireless siren (if connected to the control panel)

Press “6” Turns all sirens o

Press “9”

- Turns the built-in siren on (whether the siren ringing settings is ON or OFF)

- Turns the wireless siren on (if connected to the control panel)

Press “#”

- Turns all sirens o

- Exits control by phone call

- Stops call recycles

Note

In GSM mode, the audio monitoring is not limited in time.

DE ITFR

Setup by SMS

IMPORTANT: BEFORE USING FOR THE FIRST TIME

Insert a SIM card in the control panel before starting SMS operations. Make sure the SIM card does not require any PIN code.

SAVE A SMS NUMBER IN THE CONTROL PANEL (using the control panel).

Only stored numbers can control and congure the system.

(Refer to the instructions page 8)

Each SMS operation dened in this user manual will be illustrated as follows:

You send:

SMS Command

The control panel replies:

Control panel’s reply

The rst green speech bubble is the

SMS command sent by the user.

The rst grey speech bubble is the

reply sent by the control panel.

The speech bubbles that follow are the dialogue between the user and the control panel (SMS sent by the user are in green SMS sent by the control panel are in grey).

The system is in English by default. To change the system language, refer to the instructions on page 22 of this manual.

Important

When replying to the control panel by SMS, make sure no space follows punctuation marks like "." or ":". For examples, to store SMS numbers, your SMS must be formatted as follows:

SMS numbers:

1.067890033

2.067890022

3.067890011

4.067890000

No space after "1."

DE ITFR

www.techly.com

Disarm the System

Send:

System disarmed.

Arm the System

Send:

System armed.

Home Mode

Send:

System in home mode.

Setting Enquiry

Send:

System:Disarmed AC power:on

Note

The values indicated hereinabove will change after having set up the system.

DE ITFR

Store Phone Numbers

Send:

Phone numbers:

Copy, paste, then edit (case sensitive):

Phone numbers:

1. 067890033

2. 067890022

3. 067890011

4. 067890000

Store Phone Numbers for SMS Notications

Send:

SMS numbers:

Copy, paste, then edit (case sensitive):

SMS numbers:

1. 067890033

2. 067890022

3. 067890011

4. 067890000

Note

The rst SMS number will receive SMS notications when the system

is disarmed by RFID tag. To start

receiving these notications, you

must rename the RFID tags. Up to 4 RFID tags can be renamed. Other tags will be attributed a number based on the order of registration to the control panel. Refer to the instructions on page 8 to learn how to register an RFID tag in the control panel.

DE ITFR

www.techly.com

Rename Zones

Send "91~99". For example for zone 1, send:

Zones names:

Copy, paste, then edit (case sensitive):

Zones names:

1. Entrance door sensor

Note

Zones 1 to 9 can be renamed. The name of the zone cannot consist of more than 30 Latin characters. Zones 10 to 99 cannot be renamed.

SMS Alert for Accessory Low Battery

(available for two-way acessories such as Motion Detectors)

For accessories assigned to zones that have been renamed, an SMS will be sent under the format “Zone name + low battery”.

Bedroom PIR low battery

For accessories assigned to zones that have not been renamed, an SMS will be sent under the format “Zone

number + low battery”.

Zone 10 low battery.

SMS Alert for Accessory Tamper Alarm

(available for two-way acessories such as Motion Detectors)

For accessories assigned to zones that have been renamed, an SMS will be sent under the format “Zone name + tamper alarm”.

Bedroom PIR tamper alarm.

For accessories assigned to zones that have not been renamed, an SMS will be sent under the format “Zone

number + tamper alarm”.

Zone 10 tamper alarm.

DE ITFR

Rename RFID Tag

Send:

Rename RFID tag names:

Copy, paste, then edit (case sensitive):

Rename RFID tag names:

1. Tom

2. Nurse

3. Nancy

4. David

Note

The rst SMS number will receive SMS notications when the system

is disarmed by RFID tag. To start

receiving these notications, you

Entry and Exit Delay Time

Send:

Entry delay time(0-300sec):0 Exit delay time(0-300sec):0

Copy, paste, then edit (case sensitive):

Entry delay time(0-300sec):10 Exit delay time(0-300sec):20

Note

This function can be used if you do not want to bring a remote control or a RFID tag with you.

When you arm the system, the system will be armed after the delay set. When you disarm the system, the system will be disarmed after the delay set.

When arming the system, you hear one beep every second to remind you to leave. The beep rhythm speeds up during the last 10 seconds. If an intruder is detected, the alarm will be delayed accordingly.

DE ITFR

www.techly.com

Siren Volume and Ringing Time

Send:

Siren volume(0=Mute,1=High):1 Siren ringing time(1-9min):3

Copy, paste, then edit (case sensitive):

Siren volume(0=Mute,1=High):0 Siren ringing time(1-9min):5

Disarm Password

Send:

Disarm password (4 digits): 1234

Copy, paste, then edit (case sensitive):

Disarm password (4 digits): 4321

DE ITFR

Change System Language

Send the code corresponding to the language you want to set. For example, for English, send “0001”.

0001

Refer to the table below for the full list of languages:

0001 English 0002 French 0003 German 0004 Italian

Languages available may vary depending on the version of your product.

Restore System to Factory Settings by SMS

Send:

0000

The settings will be restored to default values. Stored phone numbers and connected accessories will not be deleted.

Note

Only stored numbers can send the SMS to restore factory settings.

DE ITFR

www.techly.com

Accessories

Wireless Remote Control

Home Mode

Arm

SOS

Disarm

LED indicator

Arm the system

Press the Arm button " " to arm the alarm system. The LED indicator lights up (the control panel beeps once). The system is armed.

If an intruder is detected, the siren

rings out. (The siren turns o after 5

minutes as per default settings.) In the meantime, the system dials the stored phone numbers automatically.

Disarm the system

Press the Disarm button " " to disarm the alarm system. The LED indicator

turns o (the control panel beeps

twice). The system is disarmed.

Home Mode

Press the Home Mode button " " on the remote control. The system state LED is on. All the sensors in regular zones are armed except those in the Home Mode zone. The sensors in the Home Mode zone are disarmed so that users can move inside their home.

DE ITFR

Mute Mode

Press the Home Mode button " " and then the Arm "

" or Disarm " " button immediately after. Doing so, the control panel does not beep when you arm or disarm your system.

Emergency Mode

Regardless the status of the system, the alarm is triggered when the SOS button "SOS" is pressed on the remote control.

At the same time, the control panel

sends a notication by SMS ("RC-01

SOS", 01 being the remote control's

number) and dials the pre-stored phone numbers.

Refer to the instructions in the table on page 8 of this manual "Remote & Keypad".

Specications

Power supply

DC 3V (CR2025 button battery x1)

Static current

≤10 uA

Operating current

≤7 mA

Transmission distance

≤ 80 m (in open area)

Radio-frequency:

433MHz (±75KHz)

Housing material

ABS plastic

Operating conditions

Temperature: -10°C ~ +55°C

Relative Humidity: ≤80%

(non-condensing)

Dimensions

57 x 31 x 11 mm

DE ITFR

www.techly.com

Wireless Motion Detector

Design

1. LED indicator

2. Detection window

3. Bracket

LED indications

Blinks continuously: self-testing Blinks once: an intruder is detected Blinks twice: self-testing is complete;

entering working mode. Blinks once every 3 seconds: undervoltage indication, the batteries must be replaced. (You will be informed by SMS when the batteries are low if the motion detector is registered in the control panel.)

PCB Layout

Alarm zone setup Tamper switch*

Infrared sensor**

AA 1.5V LR6

Antenna

LED working

indicator

*Tamper switch

When the alarm system is armed, the tamper switch will trigger the alarm if the case is opened.

**Infrared sensor

Detects the infrared rays released by human body motion. Do not touch the surface. Keep the surface clean.

DE ITFR

Usage

Open the case and remove the battery activation strip. Self-testing will start for 30 seconds.

When the sensor is in operation, if it is triggered more than twice within 3 minutes, it will switch to standby mode to save power. If no movement is detected within the next 3 minutes, the sensor goes back to working mode.

Connect Button

Navigate through the menu of the control panel and reach "ADD A NEW" (Wireless Sensor). Press the Connect button at the back of the motion sensor or trigger the sensor (by moving in front of it) to register the detector in the control panel.

Installation

Avoid mounting the detector close to windows, air conditioner, heater, refrigerator, oven, sunshine and places where the temperature changes fast or where the air

stream ows frequently.

If two detectors are installed in the same detection scope, adjust the location to avoid interferences and false alarms.

Fix the bracket on the wall with screws and attach the detector to the bracket. Adjust the bracket to change the detection distance and angle. It is recommended to mount the detector 2.2 m from the ground.

Top

Bottom

Ground

2.2 m

The detector is more sensitive to cross movements than vertical movements.

DE ITFR

www.techly.com

Testing

A. After the installation, turn the detector on. After one minute of self-testing,

press the test button, walk in the scope of detection and watch the LED indicator to make sure the detector is working.

B. The LED indicator blinks once when body movement is detected.

C. Adjust the detector angle to achieve the best detection performance.

Specications

Power supply

DC 3V (AA 1.5V LR6 Batteries x 2)

Static current

≤ 30uA

Alarm current

≤ 15 mA

Detection scope

8m / 110°

Transmission distance

≤ 80m (in open area)

Radio-frequency

433 MHz (±75 KHz)

Housing material

ABS plastic

Operating conditions

Temperature: -10°C~55°C

Relative humidity: ≤ 80% (non-

condensing)

Detector dimensions (L x W x H)

107 x 53 x 32 mm

Bracket dimensions (L x W x H)

52 x 30 x 26.5 mm

Detection Scope

110°

Top view

0m 2m 4m 6m 8m

Side view

DE ITFR

Wireless Door / Window Contact

Features

This Door / Window Contact can be installed on doors, windows, and any other objects that open and close. The sensor sends a signal to the control panel when the magnet is separated from the transmitter.

Thanks to the tamper switch, any attempt to remove the cover of the Door / Window Contact will trigger the alarm.

Design

LED indicator

Magnet

Transmitter

PCB Layout

Tamper switch

AA 1.5V LR6 battery

Zone setting

LED indications

Blinks once: the door or window is open and the transmitter sends a signal to

the control panel.

DE ITFR

www.techly.com

Installation

- Open the case and remove the battery

activation strip.

- Mount the sensor on the door and the magnet

on the door frame.

- Make sure the magnet is placed above the

transmitter.

- Mount the magnet max. 1 cm away from the

transmitter and secure the transmitter and magnet with double-sided tape or screws.

- Avoid mounting the sensor in areas with a

large amount of metal or electrical wiring such as a furnace or utility room.

Specications

Power supply

DC 1.5V (AA 1.5V LR6 battery x 1)

Static current

≤ 30 uA

Alarm current

≤ 40mA

Transmitting distance

≤80 m (in open area)

Radio-frequency

433 MHz (±75 KHz)

Housing material

ABS plastic

Operating conditions

Temperature: -10°C~55°C

Relative humidity: ≤ 80% (non-condensing)

Transmitter dimensions (LxWxH)

71 x 35 x 17.5 mm

Magnet dimensions (LxWxH)

51 x 12 x 13.5 mm

DE ITFR

RFID Tag

Features

The RFID tag enables you to disarm your system or unlock electronic door locks.

Refer to the instructions in the table page 8 of this manual (“RFID TAG”).

Specications

Dimensions

45 x 30 x 7 mm

+ 102 hidden pages

Techly I-ALARM-KIT001 Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual